User Manual - LUCKINSlive
Contents
1. 34 EIO0000000233 03 2012 Configuration Runtime Tab Introduction The Modbus SL Comm DTM provides different types of runtime information This chapter describes the information provided by the Modbus SL Comm DTM and the configuration of the log function Runtime Tab The Modbus SL Comm DTM provides different types of runtime information which can be used to monitor the established communications The runtime information is available on the Runtime tab of the Modbus SL Comm DTM which can be accessed in the following manner e Inthe network view of your FDT Frame Application double click the Modbus SL Comm DTM icon Now select the Runtime tab e Inthe network view of your FDT Frame Application right click the Modbus SL Comm DTM icon and then click Configuration Now select the Runtime tab The following figure shows the Runtime tab of the Modbus SL Comm DTM dialog lt gt ModbusSLCommunicationD 41D x Modbus Modbus Serial Communication DTM Schneider 204 d Electric Serial Configuration Runtime AddressTable Scan Communication Connections 0 Sent messages 0 Received messages 0 Exceptions 0 Timeouts 0 Log View Log File C Documents and Settings admin My Documents ModbusSLLog log Log Mode Deactivated v lt b Disconnected j Data set E100000000233 03 2012 35 Configuration Configuration Commands The following2. 34 H ntime Tab seein tse each pan eec PER Uvade vtt ele 35 Address Table rco deb Sa e DEUS SEL Re deris 37 Scan Configuration 000 cece ene 39 GlosSary 4 2 xxm an an T EE E TE 41 Index 1 346 e4eEiuaGa en xx Rie Bossa wen ee eee oi 45 EIO0000000233 03 2012 3 EIO0000000233 03 2012 Safety Information A Important Information NOTICE Read these instructions carefully and look at the equipment to become familiar with the device before trying to install operate or maintain it The following special messages may appear throughout this documentation or on the equipment to warn of potential hazards or to call attention to information that clarifies or simplifies a procedure The addition of this symbol to a Danger safety label indicates that an electrical hazard exists which will result in personal injury if the instructions are not followed personal injury hazards Obey all safety messages that follow this symbol to avoid possible injury or death A DANGER DANGER indicates an imminently hazardous situation which if not avoided will result in death or serious injury A WARNING WARNING indicates a potentially hazardous situation which if not avoided can result in death or serious injury This is the safety alert symbol It is used to alert you to potential EIO0000000233 03 2012 5 PLEASE NOTE A CAUTION CAUTION indicates a potentially haz
3. FDT Frame Application DTM Channel 1 PC with Modbus SL Comm DTM 2 4 target devices 20 EIO0000000233 03 2012 Connection Types and Communication Models Modem Connection The Modbus SL Comm DTM can be used in conjunction with a standard serial line modem to establish Modbus communications to remote devices FDT Frame Application DTM Channel PC with Modbus SL Comm DTM standard serial modem telephone line industrial serial modem 6 target devices UN EIO0000000233 03 2012 21 Connection Types and Communication Models 22 EIO0000000233 03 2012 DTM Graphical User Interface Graphical User Interface Overview This chapter describes the graphical user interface GUI of the Modbus SL Comm DTM E100000000233 03 2012 23 Graphical User Interface Introduction The following figure shows the GUI graphical user interface of the DTM lt gt ModbusSLCommunicationD dbx Modbus Modbus Serial Communication DTM S cbneider nu Electric Serial Configuration Runtime AddressTable Scan Connection T ype Serial Line COM Port COMI w Link parameters Default C Auto Adaptation Parity Stop Bits Baud Rate J ONone 15 19200 v Odd O 2Bits O Even Global Mode Timeout 300000 RTU 8 Bits Rey 0 ASCII 7 Bits J lt b Disconnected J D
4. All parameter modifications are canceled and the Modbus SL Comm DTM window will be closed The original values will be applied at the next connection Default Displays the default parameter values Apply Saves the parameters but the Modbus SL Comm DTM window remains open The new parameter values will be applied at the next connection EIO0000000233 03 2012 29 Configuration Serial Configuration for Modbus SL Comm DTM Introduction This chapter describes the parameters of the Modbus SL Comm DTM for RS232 RS485 connections Serial Parameters The following table contains a description of the communication parameters for a serial line connection e RTU 8 bits e ASCII 7 bits Parameter Description Default value Auto Adaptation Enables disables the auto adaptation function Disabled which can be used to detect the communication parameters for Modbus Serial Line automatically COM Port PC COM port COM1 Baud Rate serial line baud rate 19200 Parity serial line parity Even Stop Bits number of stop bits 1 Global Timeout Modbus slave response timeout 3000 ms Retry Number Number of times the Modbus Comm DTM will 0 resend the Modbus request on the serial connection if a communication timeout occurred Mode Transmission mode RTU 30 EIO0000000233 03 2012 Configuration Bluetooth Configuration for Modbus SL Comm DTM Introduction Th
5. EIO0000000233 03 2012 17 Connection Types and Communication Models Direct Connection The Modbus SL Comm DTM can be used to establish a direct Modbus communication between the PC and the target device For the direct connection the following physical connection types are supported RS232 RS485 by using an RS232 RS485 converter USB by using an USB Serial Line converter USB by using a direct USB cable see your hardware manual for the correct cable reference 1 2 FDT Frame Application DTM Channel Device DTM PC with Modbus SL Comm DTM target device 18 EIO0000000233 03 2012 Connection Types and Communication Models Bluetooth Connection Bus Connection The Modbus SL Comm DTM can be used to establish a direct Modbus communication between the PC and the target device via Bluetooth FDT Frame Application 1 PC with Modbus Serial Comm DTM 2 target device The Modbus SL Comm DTM can be used in conjunction with a RS232 RS485 converter to establish a Modbus communication to a Modbus Serial Line bus FDT Frame Application DTM Channel 1 PC with Modbus SL Comm DTM 2 4 target devices EIO0000000233 03 2012 19 Connection Types and Communication Models Gateway Connection The Modbus SL Comm DTM can be used to establish a Modbus communication to Modbus serial devices behind a Modbus TCP Modbus Serial gateway
6. relevant instructions must be followed Failure to use Schneider Electric software or approved software with our hardware products may result in injury harm or improper operating results Failure to observe this information can result in injury or equipment damage 2012 Schneider Electric All rights reserved EIO0000000233 03 2012 Table of Contents Safety Information lesser 5 About the Book 0 0 00 cece 7 Chapter 1 Hardware and Software Requirements 9 System Requirements 0 0 0 cece esee 10 Compatibilty u re EE em dad eos eet eed 12 Considerations 0 0 cee ne 13 Installing and Removing the Modbus Comm DTM 14 Chapter 2 Connection Types and Communication Models 15 Connection Types for Modbus SL Comm DTM 2 55 16 Communication Models for Modbus SL Comm DTM 17 Chapter 3 DTM Graphical User Interface 23 Graphical User Interface 1 0 0 cee 23 Chapter 4 Configuration 0000 eee 27 Configuration Tab for Modbus SL Comm DTM 2 5 28 Serial Configuration for Modbus SL Comm DTM 30 Bluetooth Configuration for Modbus SL Comm DTM 31 Remote Gateway Configuration for Modbus SL Comm DTM 32 Modem Connection Configuration for Modbus SL Comm DTM 33 USB Connection Configuration for Modbus SL Comm DTM
7. O Odd O 2 Bits Even Global Mode Timeout 3000 RTU 8 Bits Retry 0 v O ASCII 7Bits lt lt Disconnected j Data set 28 EIO0000000233 03 2012 Configuration Connection Type In the combo box Connection Type on the Configuration tab of the Modbus SL Comm DTM you can select the connection type for the Modbus communication The following table contains a list of connection types available for selection Connection Type Description Serial Line This connection type shall be selected for the following connections e RS232 e RS485 e USB to RS232 converters e USB to RS485 converters Remote Gateway For Modbus communications with serial devices which are located behind a Modbus TCP Modbus SL gateway select this connection type Modem Select this connection type if a remote connection via a standard serial modem shall be used for communication Bluetooth Select this connection type if the communication to the target device shall be established via Bluetooth USB Select this connection type if you are making a direct USB connection Configuration Commands The following table contains a description of the configuration commands available in the Configuration tab Command Description Ok All parameters will be saved and the Modbus SL Comm DTM window will be closed The new parameter values will be applied at the next connection Cancel
8. SL Comm DTM will resend the Modbus request if a communication timeout occurred 32 EIO0000000233 03 2012 Configuration Modem Connection Configuration for Modbus SL Comm DTM Introduction This chapter describes the configuration of the Modbus SL Comm DTM for the use with a standard serial modem to establish a remote connection Modem Connection Configuration The following table contains a description of the parameters for a remote connection established via a standard serial modem Parameter Description Modem List of modems installed on the PC Select the modem which shall be used to establish the remote connection Global Timeout Modbus slave response timeout Retry Number Number of times the Modbus SL Comm DTM will resend the Modbus request if a communication timeout occurred Phone Number Enter the phone number of the remote network EIO0000000233 03 2012 33 Configuration USB Connection Configuration for Modbus SL Comm DTM Introduction This chapter describes the configuration of the Modbus SL Comm DTM for a direct USB connection USB Connection Configuration The following table contains a description of the parameters for an USB connection Parameter Description Global Timeout Modbus slave response timeout Retry Number Number of times the Modbus SL Comm DTM will resend the Modbus request if a communication timeout occurred
9. tab of the Modbus SL Comm DTM Command Description Scan Mode Scan Mode Monopoint Select this connection type only for direct connections where the target device is directly connected to the PC scanned Address Range 248 Multipoint Select this connection type only for multipoint connections where the PC is connected to a Modbus Serial Line network Scan Address Range Scan Address Range Single Scans only a single address of one target device in the range between 1 247 Range Scans a specified address range between 1 247 All Scans the complete address range of the Modbus Serial connection all addresses between 1 247 A WARNING UNINTENDED EQUIPMENT OPERATION Do not use the scan mode Monopoint on a Modbus multipoint network Only use the scan mode Monopoint with point to point communication that is directly between the PC and the device Failure to follow these instructions can result in death serious injury or equipment damage 40 EIO0000000233 03 2012 Glossary configuration CRC DTM The arrangement and interconnection of hardware components within a system and the hardware and software selections that determine the operating characteristics of the system cyclic redundancy check Messages that implement this error checking mechanism have a CRC field that is calculated by the transmitter according to the message s content
10. Comm DTM double click on the file setup exe and follow the instructions in the installation wizard Removal To remove the Modbus Comm DTM from your computer choose Start Settings Control Panel Add Remove Programs 14 EIO0000000233 03 2012 Connection Types and Communication Models 2 Introduction This chapter gives an overview about the different configurations the Modbus Comm DTM can be used with to establish Modbus communications What s in this Chapter This chapter contains the following topics Topic Page Connection Types for Modbus SL Comm DTM 16 Communication Models for Modbus SL Comm DTM 17 E100000000233 03 2012 15 Connection Types and Communication Models Connection Types for Modbus SL Comm DTM Introduction The Modbus SL Comm DTM can be used to establish Modbus communications based on different connection types Serial Connection The Modbus SL Comm DTM provides the possibility to establish a Modbus communication via a standard PC serial port USB RS232 USB RS485 Converter Connection The Modbus SL Comm DTM can be used to establish a Modbus communication via a USB RS232 or USB RS485 converters NOTE The Modbus SL Comm DTM only supports USB converters which can be accessed as Virtual COM Ports USB Connection The Modbus SL Comm DTM can be used to establish a Modbus communication by using the following cables e TCS XCN AMUM3P e UNY XCA USB 033 e BMX XCA
11. EIO0000000233 02 Modbus Serial Communication Device Type Manager User Manual 03 2012 www schneider electric com Schneider Electric The information provided in this documentation contains general descriptions and or technical characteristics of the performance of the products contained herein This documentation is not intended as a substitute for and is not to be used for determining suitability or reliability of these products for specific user applications It is the duty of any such user or integrator to perform the appropriate and complete risk analysis evaluation and testing of the products with respect to the relevant specific application or use thereof Neither Schneider Electric nor any of its affiliates or subsidiaries shall be responsible or liable for misuse of the information contained herein If you have any suggestions for improvements or amendments or have found errors in this publication please notify us No part of this document may be reproduced in any form or by any means electronic or mechanical including photocopying without express written permission of Schneider Electric All pertinent state regional and local safety regulations must be observed when installing and using this product For reasons of safety and to help ensure compliance with documented system data only the manufacturer should perform repairs to components When devices are used for applications with technical safety requirements the
12. Glossary M master slave model The direction of control in a network that implements the master slave model is from the master to the slave devices MB abbreviation for Modbus Modbus Modbus is an application layer messaging protocol Modbus offers many services specified by function codes S SL abbreviation for Serial Line T TCP transmission control protocol A connection oriented transport layer protocol that provides reliable full duplex data transmission TCP is part of the TCP IP suite of protocols telegram A data packet used in serial communication E100000000233 03 2012 43 Glossary 44 EIO0000000233 03 2012 Index A address table 37 auto adaptation 30 bluetooth connection 17 bluetooth configuration 31 C communication models 17 compatibility 12 configuration tab 28 connection bluetooth 16 17 bus 17 direct 17 direct RS232 17 direct RS485 17 direct USB BMX XCA USB H018 045 17 direct USB TCS XCN AMUMGP 17 direct USB UNY XCA USB 033 17 direct USB serial line 17 gateway 16 17 serial 16 serial modem 16 17 types 16 USB 16 USB RS232 converter connection 16 USB RS485 converter connection 16 considerations 13 D DTM graphical user interface 23 G graphical user interface 23 installation 14 M modem connection configuration 33 EIO0000000233 03 2012 45 Index R remote gateway configuration 32 r
13. Receiving nodes recalculate the field Disagreement in the two codes indicates a difference between the transmitted message and the one received D A DTM Device Type Manager is a kind of device driver which is provided by the field device vendor The DTM contains the device specific information and provides a graphical user interface The DTM can be used to perform monitoring tasks and configuration tasks on the specific device A DTM is not a standalone application it requires an FDT Frame Application to run EIO0000000233 03 2012 41 Glossary Ethernet FDT function code A LAN cabling and signaling specification used to connect devices within a defined area e g a building Ethernet uses a bus or a star topology to connect different nodes on a network F The FDT Field Device Tool technology standardizes the communication interface between field devices and systems www fdtgroup org A function code is an instruction set commanding 1 or more slave devices at a specified address es to perform a type of action e g read a set of data registers and respond with the content G gateway A program or hardware that passes data between networks IP internet protocol That part of the TCP IP protocol family that tracks the internet addresses of nodes routes outgoing messages and recognizes incoming messages LAN local area network A short distance data communications network 42 EIO0000000233 03 2012
14. Serial Comm DTM requires the Schneider Modbus Serial PC Driver installed on the system EIO0000000233 03 2012 11 Hardware and Software Requirements Compatibility FDT Compatibility The Modbus Comm DTM is compliant to the FDT standards FDT 1 2 and FDT 1 2 1 It is based on the FDT Modbus Annex 1 0 Modbus Compatibility The Modbus Comm DTM supports Modbus services specified in the Modbus Application Protocol specification V1 1b 12 EIO0000000233 03 2012 Hardware and Software Requirements Considerations Windows User Rights The Modbus SL Comm DTM can be run under Windows Vista Windows 7 with administrator access rights without any restrictions If you want to run the Modbus SL Comm DTM under Windows Vista Windows 7 with standard user rights the maximum number of concurrent Modbus connections is limited to 4 connections In addition the following steps must be performed after the installation process is finished open the Windows Control Panel double click the Driver Manager icon open the Modbus Serial Driver tab configure and start all 4 instance of the Modbus Serial PC Driver check if all instances are running 4 icons of the Modbus Serial Driver in the system tray NOTE To perform these steps administrator access rights are required EIO0000000233 03 2012 13 Hardware and Software Requirements Installing and Removing the Modbus Comm DTM Installation To install the Modbus
15. USB H018 045 Gateway Connection The Modbus SL Comm DTM can be used to establish a Modbus communication to Modbus serial devices behind a Modbus TCP Modbus Serial gateway In this case the connection is established via the Ethernet network adapter of the PC Bluetooth Connection The Modbus SL Comm DTM provides the possibility to establish a Modbus communication via Bluetooth NOTE The Modbus SL Comm DTM only supports Bluetooth adapters which implement the Bluetooth Serial Port Profile SPP Serial Modem Connection The Modbus SL Comm DTM can be used in conjunction with standard serial line modems to establish Modbus communications to remote devices 16 EIO0000000233 03 2012 Connection Types and Communication Models Communication Models for Modbus SL Comm DTM Introduction This chapter describes the different communication models supported by the Modbus SL Comm DTM NOTE The FDT Technology is not designed for real time data transfer Depending on your system and communication model you employ the data may not reflect the actual real time device state A WARNING INVALID DEVICE STATE INFORMATION Do not use the Modbus Comm DTM for time critical controlling or monitoring tasks because the transferred data may not reflect the actual device state The FDT Technology is not designed for this purpose Failure to follow these instructions can result in death serious injury or equipment damage
16. ardous situation which if not avoided can result in minor or moderate injury NOTICE NOTICE is used to address practices not related to physical injury Electrical equipment should be installed operated serviced and maintained only by qualified personnel No responsibility is assumed by Schneider Electric for any consequences arising out of the use of this material A qualified person is one who has skills and knowledge related to the construction and operation of electrical equipment and its installation and has received safety training to recognize and avoid the hazards involved EIO0000000233 03 2012 About the Book A At a Glance Document Scope This user manual is intended to describe the use of the Communication Device Type Manager Comm DTM for Modbus Validity Note This document has been updated with the release of Comm DTM V2 0 EIO0000000233 03 2012 7 Product Related Information User Comments A WARNING LOSS OF CONTROL e The designer of any control scheme must consider the potential failure modes of control paths and for certain critical control functions provide a means to achieve a safe state during and after a path failure Examples of critical control functions are emergency stop and overtravel stop power outage and restart e Separate or redundant control paths must be provided for critical control functions e System control paths may include communicatio
17. ata set ai 1 Identification area 2 Tab menu 3 4 Parameter status icons 5 Status bar Identification Area The identification area shows the name and the version of the DTM Tab Menu Use the tab menu to access the different functions provided by the DTM EIO0000000233 03 2012 24 Graphical User Interface Parameter Status Icons The parameter status icons provide information about the current state of the parameter Possible parameter states Icon Meaning The parameter was modified and has an invalid value The parameter was modified and has a valid value Status Bar The status bar provides information about the current status of the DTM Possible connection states Icon Text Meaning DTM State A Disconnected disconnected all other states t Connecting connecting going online E T e Connected connected online de Disconnecting disconnecting going offline a Interrupted interrupted detected communication interruption lt EIO0000000233 03 2012 25 Graphical User Interface Possible data source states Icon Text Behavior Data set Displayed values are loaded from the instance data set Changed values are affected on the instance data set only Data set locked Displayed values are loaded from the instance data set Data set is locked 26 EIO0000000233 03 2012 Configurati
18. e on System 30 MB Drive Free Hard Drive Space on Installation 60 MB Drive Swap File 1024 MB 2048 MB Monitor Display 256 color SVGA 800 x 600 resolution True color XGA 1024 x 768 resolution Software Requirements Software operating systems Operating System Edition Service Pack Special Considerations Windows 2000 SP2 or later Windows XP Professional SP2 or later Windows Vista 32 Bit SP2 Windows Vista 64 Bit SP2 Windows 7 32 Bit Windows 7 64 Bit Windows 7 XP mode Virtual PC You need administrator access rights to install the Modbus Serial Comm DTM 1 with Windows 7 XP Application mode You must use the Windows 7 XP Virtual PC mode SoMachine is not copatible EIO0000000233 03 2012 Hardware and Software Requirements Software installed on the PC Software Edition Special Considerations Microsoft NET Framework V2 0 FDT Frame Application FDT 1 2 or FDT 1 2 1 The Modbus SL Comm DTM requires an FDT Frame Application compliant to the FDT standard The FDT Frame Application must support the Microsoft NET Framework 2 0 Schneider Modbus Serial PC Driver Editions V1 8 IE35 Windows XP 32 Bit V2 0 IE10 Windows Vista 32 Bit V1 10 IE37 Windows XP 32 Bit V2 2 IE12 Windows Vista 32 Bit V3 2 IE12 Windows Vista 64 Bit V2 2 IE12 Windows 7 32 Bit V3 2 IE12 Windows 7 64 Bit The Modbus
19. equirements hardware 10 software 10 retry number 30 31 32 33 34 RS232 28 RS485 28 runtime tab 35 S scan configuration 39 scan mode 39 serial configuration 30 U USB connection configuration 34 user interface 23 46 EIO0000000233 03 2012
20. ing figure shows the Address Table tab of the Modbus SL Comm DTM dialog lt gt ModbusSLCommunicationD I gt X Modbus Modbus TCP Communication DTM Schneider d Electric Address Instance Name Name Vendor Altivar_1 Altivar 71 Schneider Electric Altivar_1 Altivar 71 Schneider Electric Universal_1 Universal Modbus Se Schneider Electric ies Fe t Disconnected 3 Data set EIO0000000233 03 2012 37 Configuration Configuration Commands The following table contains a description of the configuration commands available in the Address Table tab Command Description OK All modifications will be saved and the Modbus SL Comm DTM window will be closed The new values will be applied at the next connection Cancel All modifications are canceled and the Modbus SL Comm DTM window will be closed The original values will be applied at the next connection Apply Saves the modifications but the Modbus SL Comm DTM window remains open The new values will be applied at the next connection Address Information The following table contains a description of the address information available on the Address Table tab of the Modbus SL Comm DTM Parameter Description Address Target address of the hardware device which shall be configured with the connected DTM Instance Name Instance name of the DTM Name DTM specific name Vendor DTM vendor
21. is chapter describes the configuration of the Modbus SL Comm DTM for a Bluetooth connection Bluetooth Configuration The following table contains a description of the parameters for Bluetooth connections Parameter Description Bluetooth This combo box contains a list of found virtual COM Ports provided by the Bluetooth adapters installed on your PC Select the COM Port on which the Modbus communication shall be established NOTE If the desired COM Port is not available for selection try to establish the communication with the following configuration setthe Connection Type to serial line e select the desired COM Port in the combo box Global Timeout Modbus slave response timeout Retry Number Number of times the Modbus SL Comm DTM will resend the Modbus request on the Bluetooth connection if a communication timeout occurred EIO0000000233 03 2012 31 Configuration Remote Gateway Configuration for Modbus SL Comm DTM Introduction This chapter describes the configuration of the Modbus SL Comm DTM for the remote gateway connection Remote Gateway Configuration The following table contains a description of the parameters for remote gateway connections Parameter Description Remote Gateway IP Address of the Modbus SL Comm DTM gateway behind which the target devices are located Global Timeout Modbus slave response timeout Retry Number Number of times the Modbus
22. n links Consideration must be given to the implications of unanticipated transmission delays or failures of the link e Observe all accident prevention regulations and local safety guidelines e Each implementation of this equipment must be individually and thoroughly tested for proper operation before being placed into service Failure to follow these instructions can result in death serious injury or equipment damage For additional information refer to NEMA ICS 1 1 latest edition Safety Guidelines for the Application Installation and Maintenance of Solid State Control and to NEMA ICS 7 1 latest edition Safety Standards for Construction and Guide for Selection Installation and Operation of Adjustable Speed Drive Systems or their equivalent governing your particular location We welcome your comments about this document You can reach us by e mail at techcomm schneider electric com EIO0000000233 03 2012 Hardware and Software Requirements 1 What s in this Chapter This chapter contains the following topics Topic Page System Requirements 10 Compatibility 12 Considerations 13 Installing and Removing the Modbus Comm DTM 14 EIO0000000233 03 2012 Hardware and Software Requirements System Requirements Hardware Requirements Requirement Minimum Recommended Computer Pentium 4 or equivalent Core 2 Duo RAM 1GB 2GB Free Hard Drive Spac
23. name Address Assignment The address table of the Modbus SL Comm DTM can be used to specify the target address of the hardware device which shall be configured with a specific DTM To specify the target address you have to enter the new address in the corresponding Address field of this DTM and to validate this modification by clicking either the Apply button or by clicking the Ok button A WARNING UNINTENDED EQUIPMENT OPERATION FOR MODBUS SL Do not communicate to a device with an address of 248 on a bus with multiple Modbus devices connected Only establish connections to a device using an address of 248 point to point that is directly between the PC and the device Failure to follow these instructions can result in death serious injury or equipment damage 38 E100000000233 03 2012 Configuration Scan Configuration Introduction Scan Tab The Modbus Comm DTM provides the possibility to specify the range of the scanned addresses for the FDT scan This chapter describes the configuration of the scan parameters for the FDT scan The Modbus SL Comm DTM supports the scan function as it is defined the FDT specification V1 2 1 The scan can be used to build automatically the network topology of the underlying communication network The Modbus SL Comm DTM provides the possibility to specify the range of the scanned addresses The scan parameters are available on the Scan tab of the Modbus SL C
24. nformation which will be written to the log file depending on the selected Log Mode Log Mode Description Deactivated Disables the log file feature Error Logging Only information about detected timeout errors and received Modbus exceptions will be written to the log file All Logging In addition to the information about detected timeout errors and received Modbus exceptions information about the sent Modbus requests and received Modbus responses and the requests received from the Device DTM is written to the log file 36 EIO0000000233 03 2012 Configuration Address Table Introduction Address Table The Modbus Comm DTM provides an address table which lists all connected Device DTMs and their target addresses This chapter describes the information provided in the address table and the configuration of the target addresses of the devices The Modbus SL Comm DTM provides an address table which lists all connected Device DTMs and their target addresses In this address table you can specify the target addresses of the connected Device DTMs The Address Table tab can be accessed in the following manner e In the network view of your FDT Frame Application double click the Modbus SL Comm DTM icon Now select the Address Table tab e In the Network View of your FDT Frame Application right click the Modbus SL Comm DTM icon and then click Configuration Now select the Address Table tab The follow
25. omm DTM which can be accessed in the following manner e Inthe Network View of your FDT Frame Application double click the Modbus SL Comm DTM icon Now select the Scan tab e In the Network View of your FDT Frame Application right click the Modbus SL Comm DTM icon and then click Configuration Now select the Scan tab The following figure shows the Scan tab of the Modbus SL Comm DTM dialog lt gt ModbusSLCommunicationD gt x Modbus Modbus Serial Communication DTM e 204 Scbneider Serial d Electric r r ye Configuration Runtime AddressTable Scan Scan Mode Monopoint Multipoint Scan Address Range Single 1 Range OAI lt L Disconnected j Data set EIO0000000233 03 2012 39 Configuration Configuration Commands The following table contains a description of the configuration commands available in the Scan tab Command Description OK All modifications will be saved and the Modbus Comm DTM window will be closed The new values will be applied at the next scan Cancel All modifications are canceled and the Modbus Comm DTM window will be closed The original values will be applied at the next scan Apply Saves the modifications but the Modbus Comm DTM window remains open The new values will be applied at the next scan Scan Parameters for Modbus SL The following table contains a description of the scan parameters available on the Scan
26. on What s in this Chapter This chapter contains the following topics Topic Page Configuration Tab for Modbus SL Comm DTM 28 Serial Configuration for Modbus SL Comm DTM 30 Bluetooth Configuration for Modbus SL Comm DTM 31 Remote Gateway Configuration for Modbus SL Comm DTM 32 Modem Connection Configuration for Modbus SL Comm DTM 33 USB Connection Configuration for Modbus SL Comm DTM 34 Runtime Tab 35 Address Table 37 Scan Configuration 39 EIO0000000233 03 2012 27 Configuration Configuration Tab for Modbus SL Comm DTM Introduction The Configuration tab of the Modbus SL Comm DTM contains the communication parameters for the different connection types Configuration Tab You have several possibilities to access the Configuration tab of the Modbus Serial Comm DTM e In the network view of your FDT Frame Application double click the Modbus SL Comm DTM icon e In the network view of your FDT Frame Application right click the Modbus SL Comm DTM icon and then click Configuration The following figure shows the Configuration tab of the Modbus SL Comm DTM dialog ModbusSLCommunicationD 4D x Modbus Modbus Serial Communication DTM 204 Schneider Serial d Electric Configuration Runtime AddressTable Scan Connection Type Serial Line v COM Port COM1 v Link parameters Auto Adaptation Parity Stop Bits Baud Rate None 1Bit 19200 E
27. table contains a description of the configuration commands available in the Runtime tab Command Description OK All parameters will be saved and the Modbus SL Comm DTM window will be closed The new parameter values will be applied at the next connection Cancel All parameter modifications are canceled and the Modbus SL Comm DTM window will be closed The original values will be applied at the next connection Browse opens a file browser to specify the log file path Reset resets all runtime parameters to zero Apply Saves the parameters but the Modbus SL Comm DTM window remains open The new parameter values will be applied at the next connection Runtime Parameters The following table contains a description of the runtime parameters available on the Runtime tab of the Modbus SL Comm DTM Command Description Connections Number of active connections to the Modbus SL Comm DTM Sent Messages Number of messages sent by the Modbus SL Comm DTM Received Messages Number of messages received by the Modbus SL Comm DTM Exceptions Number of Modbus Exception messages received by the Modbus SL Comm DTM Timeout Errors Number of detected timeout errors on reception Log File The Modbus SL Comm DTM provides the possibility to create a log file In the Log File box you must specify the path in which the log file shall be stored The following table describes the i
Download Pdf Manuals
Related Search