Home

Spectra Led Flood USER MANAUAL

1. S button so the red LED s come on this means you can now start to set the DMX address 2 Press the 0 button so the green LED s come on this means the first digit Q the hundreds place setting is successful 3 Now Press the 0 button and the blue LED s will come on this now means that the second digit 0 tens place setting is successful 4 Now Press the 2 button and all of the R G B LED s will come on this means that the final digit 2 units place setting is successful and the full DMX address setting has been changed 5 Now press the DMX MODE button to save the new address into memory Important notes Set the DMX address on each fixture before plugging into the DMX controller e The I R Remote is not usable when the fixture s are being controlled by a DMX controller The maximum transmitter distance is 10M Please make sure that you have the I R remote aimed directly at each fixture to be programmed If you do not press the DMX MODE button after you have changed the DMX address when you power down the fixture it will lose the address you have set LEDJ Exterior Spectra Led Flood DMX Set Up Notice e Be sure to follow figures 2 amp 3 when making your own cables Do not connect the cable s shield conductor to the ground lug or allow the shield conductor to come in contact with the XLR s outer casing Grounding the shield could cause a short circuit and err
2. WWW PROLIGHT CO UK og Man TEESE HS a 2 A ps ys Wa Pe _ n SPECTRA LED FLOOD EXTERIOR ORDER CODE LED J87 USER MANAUAL LEDJ Exterior Spectra Led Flood Safety WARNING FOR YOUR OWN SAFETY PLEASE READ THIS USER MANUAL CAREFULLY BEFORE YOUR INITIAL START UP CAUTION Keep this equipment away from flammable sources liquids or gases SAFETY INSTRUCTIONS Every person involved with the installation operation amp maintenance of this equipment should Be competent Follow the instructions of this manual CAUTION TAKE CARE USING THIS EQUIPMENT HIGH VOLTAGE RISK OF ELECTRIC SHOCK Before your initial start up please make sure that there is no damage caused during transportation Should there be any consult your dealer and do not use the equipment To maintain the equipment in good working condition and to ensure safe operation it is necessary for the user to follow the safety instructions and warning notes written in this manual Please note that damages caused by user modifications to this equipment are not subject to warranty LEDJ Exterior Spectra Led Flood Safety IMPORTANT The manufacturer will not accept liability for any resulting damages caused by the non observance of this manual or any unauthorised modification to the equipment Never let the power cable come into contact with other cables Handle the power cable and all mains v
3. 24W 215 10mm LEDs R 48 84 B 83 Beam angle 40 degrees e IR signal and DMX signal available Selectable built in programmes Auto run DMX mode Master Slave mode and Sound activated by IR remote please read manual for IR remote controlling e IP rating IP65 Dimensions 295 207 185mm e Weight 4 5Kgs WWW PROLIGHT CO UK
4. age and the warranty becomes void Incorrect operation may lead to danger e g short circuit burns electric shocks lamp failure etc Do not endanger your own safety and the safety of others Incorrect installation or use can cause serious damage to people and property LEDJ Exterior Spectra Led Flood Over view The outdoor DMX Spectra LED Flood together with the IR remote control can produce colourful and dynamic lighting effects lt can be used in a wide variety of venues and for outdoor building illumination Over View IR Sensor front Power In DMX In STI Power Out all DMX Out Safety Eye Hanging Bracket DMX Values and Functions CHANNEL VALUE FUNCTION 000 255 FLASH 000 slowest to 255 fastest LEDJ Exterior Spectra Led Flood I R Remote I R Remote purchased separately LEDJ90B Functions The BLACKOUT button is used to set the LED s into the power on or off modes The AR button is used to set the LED s into the auto run mode The S PR button is used to set the LED s to run the built in programmes Built in programme selection 7 colour selection colour changing and colour fade Choose between the 9 built in programmes by pressing the and buttons The FL button is used to set the LED s to flash on and off to change the flash frequency use the and buttons The SP button is used to set the run speed this button is available only in the colo
5. atic behaviour common DMX 512 in 3 pin XLR XLR MALE SOCKET XLR FEMALE SOCKET XLR Pin Configuration 2 cold 1 ground 1 ground 2 cold Pin 1 Ground O Pin 2 Negative DMX 512 out 3 pin XLR i i i i lt i a a a ae a ti ji ty FIGURE 3 FIGURE 2 Special Note Line termination When longer runs of cable are used you may need to use a terminator on the last unit to avoid erratic behaviour Termination reduces signal transmission problems O and interferance it is always advisable to connect a DMX terminal resistance 120 Ohm 1 4 W between pin 2 DMX and pin 3 DMX of the last fixture Using a cable terminator part number CABL90 will decrease the possibilities of erratic behaviour 5 Pin XLR DMX Connectors Some manufactures use 5 pin XLR connectors for data transmission in place of 3 pin 5 Pin XLR fixtures may be implemented in a 3 pin XLR DMX line When inserting standard 5 pin XLR connectors in to a 3 pin line a cable adaptor must be used The Chart below details the correct cable conversion 3 Pin XLR socket Pin 1 GN screeh Pin 2 Signal Pin 3 Signal A 5 Pin XLR socket 3 Pin XLR socket f Pin 1 GND screen Pin 1 GND screen Pin 2 Signal R PON Pin 3 Signal in 4 Pin 5 N C LEDJ Exterior Spectra Led Flood Specifications Spectra Flood Specifications Input power 240V 50HZ Power consumption
6. oltage connections with particular caution Never remove warning or informative labels from the equipment Do not open the equipment and do not modify the equipment Do not connect this equipment to a dimmer pack Do not switch the equipment on and off in short intervals as this will reduce the system s life Do not expose to flammable sources liquids or gases e Always disconnect the power from the mains when equipment is not in use before cleaning Only handle the power cable by the plug Never pull out the plug by pulling the power cable e Make sure that the available voltage is between 220v 240v e Make sure that the power cable is never crimped or damaged Check the equipment and the power cable periodically If the equipment is dropped or damaged disconnect the mains power supply immediately Have a qualified engineer inspect the equipment before operating again If your product fails to function correctly discontinue use immediately Pack the unit securely preferably in the original packing material and return it to your Prolight dealer for service e Only use fuses of same type and rating Repairs servicing and power connection must only be carried out by a qualified technician THIS UNIT CONTAINS NO USER SERVICEABLE PARTS e WARRANTY One year from date of purchase OPERATING DETERMINATIONS If this equipment is operated in any other way than those described in this manual the product may suffer dam
7. ur change or colour fade modes To change the speed use the and buttons The D button is used to set the LED s into DMX mode See DMX value table The SA button is used to set the LED s into sound activated mode This function is unavailable on the Exterior Spectra Series The SL button is used to set the LED s into slave mode The S 0 1 2 3 4 5 6 7 8 and 9 buttons are used to set the DMX address for the LED s see example below The R G and B buttons are used to set the brightness for the LEDs to change the brightness use the and buttons DMX Address Examples To set the DMX address 245 1 Press the S button so the red LED s come on this means you can now start to set the DMX address 2 Press the 2 button so the green LED s come on this means the first digit 2 the hundreds place setting is successful 3 Now Press the 4 button and the blue LED s will come on this now means that the second digit 4 tens place setting is successful 4 Now Press the 5 button and all of the R G B LED s will come on this means that the final digit 5 units place setting is successful and the full DMX address setting has been changed 5 Now press the DMX MODE button to save the new address into memory To set the DMX address 002 1 Press the

Spectra Led Flood USER MANAUAL

Contents

Download Pdf Manuals

Related Search

Related Contents