sp2652 - Badger Communications
Contents
1. Additional Information FCC and ACTA Regulations However if you do make a call to an emergency number e Youmustremain on the line and briefly explain the reason for the call before hanging up e Programming testing of emergency numbers should be performed during off peak hours such as in the early morning or late evening when the emergency services tend to be less busy 44 Technical Specifications FREQUENCY CONTROL Crystal controlled PLL synthesizer TRANSMIT FREQUENCY 2401 056 2482 272 MHz RECEIVEFREQUENCY 2401 056 2482 272 MHz CHANNELS 95 Channels NOMINAL EFFECTIVE RANGE Maximum power allowed by FCC Actual operating range may vary according to environmental conditions at the time of use SIZE Handset 176mm x 51mm x 41mm Base 178mm x 128mm x 68mm WEIGHT Handset 187 grams Base 385 grams POWER REQUIREMENTS Handset 800 mAh Ni Cd Battery Pack or 1500 mAh NiMH Battery Pack Base 7 VDC 900mA MEMORY Phonebook 50 Memory locations upto 32 digits per location CID 50 Memory locations SPECIFICATIONS ARE TYPICAL AND MAY CHANGE WITHOUT NOTICE 45 Additional Information Table Of Contents 1 Important Safety 25 Advanced Operations Instructions 25 Handset and Base Pean p 25 Making Calls 3 Introduction 25 Answering Calls 4 Parts Check List 25 Redial from Base Unit 5 The Handset Layout 26 Mute Function 6 The Base Unit Layout 26 Hold Function 26 Flash2. If you do not subscribe to Caller ID services you can still use your 2652 and the other features it offers Due to regional incompatibilities Caller ID information may not be available for every call you receive In addition the calling party may intentionally block their name and phone number from being sent 16 Handset Settings From the Handset Settings menu you can select the following options to modify e RINGER VOLUME Select this option to adjust the ringer volume Use the 3 amp scroll keys to adjust the volume up or down The Handset will display a graphic indicator of the selected volume setting Press OK to confirm your selection and return to the Handset Settings menu e RINGER MELODY Select this option to adjust the ringer melody or tone Use the scroll keys to select from the six available tones Press SAVE to confirm your selection and return to the Handset Settings menu LOW BATT TONE Select this option to turn the Low Battery warning tone ON or OFF Press the OFF or ON soft keys to make your selection Press OK to confirm your selection and return to the Handset Settings menu When set to ON the Handset will emit a warning tone when a Low Battery condition is detected RANGE TONE Select this option to turn the Out of Range warning tone ON or OFF Press the OFF or ON soft keys to make your selection Press OK to confirm your selection and return to the Handset Settings menu When set to ON t
3. 33 Advanced E Advanced ET Name and Number Announce Caller ID Name and Number Announce Caller ID is an advanced feature that enables your telephone to announce the name or telephone number of callers before you answer the call Announcements are made from the Base Unit speaker You must subscribe to Caller ID service in order to use this feature Name and Number announcements are recorded in your own voice You can record up to 50 Name and Number announcements one for each entry in your Phonebook directory Each Name and Number announcement can be up to 3 seconds long Please refer to the steps below to setup Name and Number Announce NOTE If an inbound call has the Caller ID information blocked and Name and Number Announce is enabled the Base Unitwill announce PRIVATE CALLER If an inbound call has the Caller ID information out of area and Name and Number Announce is enabled the Base Unit will announce UNKNOWN CALLER Setup Name and Number Announce e Inthe idle OFF mode press MENU and use the scroll keys to select ANNOUNCE CID then press OK e Use the scroll keys to select SELECT TYPE then press OK e Use the scroll keys to select one of the four options OFF NUMBER NAME NUMBER AND NAME then press OK OFF Select this option to disable Name and Number announce NUMBER Select this option to enable Name and Number announce of received telephone numbers only e NAME Select this
4. CALLING again A charge is added to your phone bill each time this service is used REPEAT DIALING repeatedly dials the last number you called over a time interval determined by your local phone company This is useful in reaching a party whose line is busy A charge is added to your phone bill each time this service is used NOTE For handset Pay Per Use press handset BILLED SERVICES key Then use B Gp 0 scroll to your desired option Press OK to confirm It is likely that your local telephone company will assess charges to use custom features You should check with your local service provider regarding which custom services are available in your area and the associated costs for the intentional or unintentional use of Pay Per Use services Your local telephone company may provide a monthly subscription to an individual service or a package of services which gives you unlimited usage for a small monthly fee 36 Headset Operation Your 2652 cordless telephone is equipped with a 2 5mm Headset Jack for use with an optional accessory Headset for hands free operation Once you have a compatible 2 5mm Headset locate the Headset Jack on the Handset Connect the plug on the Headset cord to the jack covered with a small rubber flap on the cordless Handset The plug should fit securely Do not force the connection Operation NOTE Whenever a compatible Headset is connected to the cordless Handset the microphone on the Hand
5. Cycles Low Medium and High when Handset battery is charging Flashes when a low battery condition is detected Mute indicator On steady when the Handset microphone is muted Hold indicator On steady when the line is on hold Range Extender indicator On steady when the Range Extender is on Handset Registration indicator is displayed when a Handset is either not registered or is searching for a Base Unit 13 Handset and Base Indicators Handset LEDs LED Description e Flashes to indicate that you have new messages in your voicemail Service must be subscribed to through your local telephone company Message Waiting Base LEDs LED Description VOICEMAIL Flashes to indicate that you have new messages in your voicemail Service must be subscribed to through your local telephone company Lights when Base unit is receiving power from wall outlet Flashes when unit is in Power Backup mode Lights when line is being used by any Handset of the 2652 system Flashes when another telephone on the same line parallel extension is in use Flashes following ringing cadence while the phone is ringing Lights whenever the Handset is placed in the Base Unit charging cradle Flashes briefly when put a spare battery in the spare battery compartment Charge Mute Lights when Base microphone is muted Flashes when HOLD function is activated Speaker Lights when Ba
6. Function i 27 Volume Control 7 Getting Started 27 Page Intercom 7 Setup 28 Handsfree Speaker Operation 8 Installation of Battery Pack in 29 Base Speaker Operation Handset 29 Line in Use Indication 9 Spare Battery Charger Power 29 Low Battery Indication Backup Function 30 Conference Calling 10 Charging Of Handset Battery 30 Transferring Calls Pack 31 Message Waiting 11 Registration and Operation 31 Programming Voicemail Access i 31 VOICEMAIL Access Key 13 Basic Operation 32 Using the dedicated PLAY 13 Handset and Base Indicators KEEP and DELETE keys 15 Soft Menu Functions 32 PLAY Access Key 15 RDL Redial 32 Reprogramming PLAY 15 MENU 33 KEEP Access Key 16 Calls Log Caller ID 33 Reprogramming KEEP 17 Handset Settings 33 DELETE Access Key 17 Ringer Volume 33 Reprogramming DELETE 17 Ringer Melody 34 Name and Number Announce 17 Low Batt Tone Caller ID 17 Range Tone 34 Setup Name and Number 17 Keypad Tone Announce 17 Contrast N d 17 Language 34 Record a New Name an Number Announcement 18 Range Extender 18 Register 35 Review Play Erase or Re 19 MEM Memory peel a Name and Number 20 To Store a Number Name nnouncement 21 To Search For and Dial a 36 Custom Pay Per Use PPU Number Name Features 21 To Delete a Number Name 37 Headset Operation 22 To Edita Name or a Number ba h 23 Base Settings 38 Additional Information 23 Select Base Ringer Melody 38 In Case Of Difficulty 23 Selec
7. closer to the Base or relocate the Base Unit The layout of your home may be limiting the range Try moving the Base Unit to another position The Handset Does Not Ring When You Receive A Call Make sure you have the Handset ringer activated To set the ringer see HANDSET SETTINGS and BASE SETTINGS Make sure the telephone line cord is plugged firmly into the Base Unit and the telephone jack Make sure the power cord is plugged in You may be too far from the Base Unit You may have too many extension phones on your telephone line to allow all of them to ring Try unplugging some of the other phones You Hear Other Calls While Using Your Phone Disconnect your Base Unit from the telephone jack and plug in a regular telephone If you still hear other calls the problem is probably in your wiring or local service Call your local telephone company You Hear Noise In The Handset And None Of The Keys Or Buttons Work Make sure the power cord is plugged in 38 In Case Of Difficulty Common Cure For Electronic Equipment If the unit does not seem to be responding normally then try putting the Handset in the cradle If it does not seem to respond do the following in the order listed 1 oar w Disconnect the power to the Base Disconnect the Handset battery and spare battery pack if applicable Wait a few minutes Connect power to the Base Re install the battery pack s Watch for Handset
8. information to your local telephone company This equipment is compatible with inductively coupled hearing aids Should you experience trouble with this telephone equipment please contact For repair warranty information The telephone company may ask you to disconnect this equipment from the line network until the problem has been corrected FCC Part 15 Warning Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment The equipment has been tested and found to comply with part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try and correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver Connect the equipment into an outlet or on a circuit different from that to which the receiver i
9. option to enable Name and Number announce of recorded Name and Number announcements only NAME AND NUMBER Select this option to enable Name and Number announce of telephone numbers for calls received that don t match an entry in your phonebook or Name and Number announce of recorded Name and Number announcements Record a New Name and Number Announcement From New Phonebook Entry Follow the steps in To Store a Number Name Page 20 e After the ENTRY HAS BEEN STORED message is displayed you will then be prompted to RECORD ANNOUNCE CID e If you choose NO the entry will be stored without a Name and Number announcement e Choose YES to record a Name and Number announcement 34 Name and Number Announce Caller ID Press the RECORD key You will be prompted to RECORD AFTER TONE Speak directly into the handset microphone to record up to 3 seconds of audio You can press the STOP key when you are done or simply wait for recording to automatically stop after 3 seconds e Press PLAY to review the Name and Number announcement The audio will playback from the Base Unit speaker e You can also choose to ERASE the announcement or RECORD a new announcement From RECORD NEW function In the idle OFF mode press MENU and use the scroll keys to select ANNOUNCE CID then press OK Use the scroll keys to select RECORD NEW and then press OK Use FIND or scroll key to locate the phonebook record
10. spare battery pack can also be used to replace a drained Handset battery ensuring uninterrupted use NOTE When using the 2652 during Power Backup mode audio quality may be compromised due to reduced Power availability The Base Unit can t be used when in power backup mode 1 Open the spare battery charger by pressing the release button located on the right hand side of the Base Unit A drawer will open to reveal the spare battery compartment 2 Place a battery pack in the Ed drawer with the charge contacts 4 i facing up and to the left Sr 3 Push the drawer closed OTE The spare battery takes 24 hours to fully charge a drained battery SZ A ZA z Loo UY Wy SS Charging Of Handset Battery Pack The Handset of your 2652 cordless telephone is powered by a rechargeable battery pack It charges automatically whenever the Handset is in the Base Unit You should charge the battery pack for 12 hours when you first receive your phone You ll know the battery pack needs charging when The low battery message is displayed The Handset seems completely dead the LCD is completely clear and does not activate when you press the keys CAUTION to reduce the risk of fire or injury to persons by battery read and follow these instructions 1 Use only the appropr
11. that you want to record your announcement After you have located the desired entry press the EDIT softkey The Handset will display Press RECORD If there is already an announcement The display will prompt ANNOUNCE CID ALREADY RECORDED However you can record over the old audio by pressing the RECORD softkey twice then re record If there is no announcement recorded press RECORD softkey to make the recording Review Play Erase or Re Record a Name and Number Announcement In the idle OFF mode press MENU and use the scroll keys to select ANNOUNCE CID then press OK Use the scroll keys to select REVIEW and then press OK Use FIND or scroll key to locate the record that you want to playback Press SELECT to review the record You can use ERASE Delete current Name and Number announcement PLAY Playback the current Name and Number announcement RECORD You can re record your current Name and Number announcement 35 Advanced ae Custom Pay Per Use PPU Features AUTO CALL BACK dials the last party who called you whether or not you answered the call A charge is added to your phone bill each time you use this feature 3 WAY CALLING allows you to talk with 2 separate parties from a single line To use this feature follow these steps 1 Call your first party after the party answers 2 Press 3 WAY CALLING Wait for dial tone 3 Call your second party after the call is answered 4 Press 3 WAY
12. the following options DEL OPT SAVE DEL Select this option to delete THIS or ALL records in Caller ID memory OPT Select this option to display up to four possible dialing strings of the number stored in Caller ID memory If a number is provided in the Caller ID data the possible options to choose from will be either 7 8 10 or 11 digits For example if the original number in Caller ID menory was 808 880 8808 then the display options will be Use the D keys to make selection and then press DIAL ON or HANDSFREE to dial the number SAVE Select this option to save the displayed Caller ID record into Phonebook Memory Only Caller ID records with telephone numbers can be saved into Phonebook Memory If you need to modify the number after saving see To Edit a Name or a Number Caller ID Call Waiting ID Your 2652 is capable of displaying the name and or number of the party calling before you answer the phone Caller ID It is also capable of displaying Caller ID information in conjunction with a Call Waiting alert signal Call Waiting Caller ID With Call Waiting Caller ID the Caller ID data is displayed so you can decide whether to answer the incoming call or continue with your current conversation NOTES ABOUT CALLER ID amp CALL WAITING CALLER ID These are subscription services provided by most regional telephone service providers You must subscribe to these services to get the benefits of these features
13. to display 39 then Additional Information Additional Information Maintenance Taking Care Of Your Telephone Your 2652 cordless telephone contains sophisticated electronic parts so it must be treated with care Avoid Rough Treatment Place the Handset down gently Save the original packing materials to protect your telephone if you ever need to ship it Avoid Water Your telephone can be damaged if it gets wet Do not use the Handset outdoors in the rain or handle it with wet hands Do not install your Base Unit near a sink bathtub or shower Electrical Storms Electrical storms can sometimes cause power surges harmful to electronic equipment For your own safety use caution when using electric appliances during storms Cleaning Your Telephone Your telephone has a durable plastic casing that should retain its luster for many years Clean it only with a soft cloth slightly dampened with water or a mild soap Do not use excess water or cleaning solvents of any kind Remember that electrical appliances can cause serious injury if used when you are wet or standing in water If your Base Unit should fall into water DO NOT RETRIEVE IT UNTIL YOU UNPLUG THE POWER CORD AND TELEPHONE LINE CORDS FROM THE WALL Then pull the unit out by the unplugged cords 40 Limited Warranty The Supplier warrants to the original purchaser only the material and workmanship of this product for ONE YEAR from the date o
14. Avoid using a telephone other than a cordless type during an electrical storm There may be a remote risk of electric shock from lightning Do not use the telephone to report a gas leak in the vicinity of the leak SAVE THESE INSTRUCTIONS Introduction The 2652 is an advanced cordless telephone that operates in the 2 4 GHz frequency range Your 2652 is capable of supporting up to a maximum of 4 Handsets Using additional Handsets up to three people can be conferenced on a call 2 Handsets and the Base Speakerphone or two extensions can be conferenced on a call while two other extensions can be talking internally using the Intercom feature This manual is designed to familiarize you with the 2652 cordless telephone IMPORTANT Please record the Base ID code BS ID printed on the underside of the 2652 Base in the space below Please be certain to include all 15 digits characters Base ID Parts Check List 1 Base Unit 5 Battery Pack 2 Handset 6 Belt Clip 3 AC Power Adapter 7 User s Manual 4 Telephone Cord Telephone Cord Belt Clip Battery Pack x 2 AC Power Adapter User s Manual The Handset Layout Oe COT ae Gd eae Antenna Message Waiting Indicator Earpiece Headset Jack 2 5mm Scroll Keys On Flash Dialing Key 0 9 10 11 12 13 14 Handsfree Speakerpho
15. Base f SCIO 0 e Base During an active call press the HOLD key to place a call on hold The SPEAKER LED will flash to indicate a call is on hold Flash Function r To return to the call press either CFP G HOLD or SPEAKER FLASH You can use your 2652 with services such as Call Waiting When you receive a call waiting signal simply press the ON FLASH key on the Handset or the FLASH key on the Base when in speakerphone mode to Flash the line Volume Control ER VOLUME Advanced Operations From the Handset During an active call press the MOJN soft key then use the EF and B soft keys to adjust the earpiece volume From the Base During an active call simply press the Volume Qe Gap Keys to adjust the speakerphone volume You will hear a special tone when you reach the highest or lowest setting 26 Handset and Base Operation From Base to a particular Handset Press the Base PAGE key then press the number of the Handset you want to call e g Handset 2 Page Intercom FOO From Base to ALL Handsets To page all Handsets from the Base press the PAGE key This will cause all Handsets linked with this Base to ring Each Handset will display GLOBAL CALL FROM BASE Any Handset can answer the page and enter intercom mode with the Base by pressing any key except OFF and soft keys To end an intercom call press OFF onthe Handset or PAGE on the Base Handset 2 c
16. ER 2 Select ON to enable RANGE EXTENDER An E icon will appear in the upper left corner of Handset display indicating that RANGE EXTENDER is ON 3 Select AUTO to allow your 2652 to automatically monitor the signal strength between the Handset and Base Unit and activate whenever necessary With this option selected your 2652 may occassionally enable or disable the RANGE EXTENDER feature Use the scroll keys to select the desired setting and then press OK to confirm the selection Note When Range Extender mode is enabled your 2652 will consume more battery power That means the standby and talk time of your Handset will be shorter Register Use this option to register a Handset to the 2652 Base You can register a total of four Handsets to the 2652 Base This process is activated automatically whenever a new Handset is powered up in range of the 2652 Base You will be prompted to enter the 15 digit Base ID code printed on the underside of the Base unit After entering this code press OK The Handset will display SEARCHING FOR BASE and then FOUND BASE when the process is complete Note Base ID codes are 15 digits long and can include the following characters 0 1 2 3 4 5 6 7 8 9 or 18 MEM Memory The 2652 can store up to 50 numbers with names in memory Each memory location can hold up to 32 digits for the number for the number and up to 16 characters for the name When pr
17. Important Safety Instructions When using your telephone equipment basic safety precautions should always be followed to reduce the risk of fire electric shock and injury to persons including the following 1 2 3 10 11 Read and understand all instructions Follow all warnings and instructions marked on the product Unplug this product from the wall outlet before cleaning Do not use liquid or aerosol cleaners Use a damp cloth for cleaning Do not use this product near water for example near a bath tub kitchen sink or swimming pool Do not place this product on an unstable cart stand or table The product may fall causing serious damage Slots and openings in the Handset and Base Unit are provided for ventilation To protect it from overheating these openings must not be blocked by placing the product on a bed sofa rug or other similar surface This product should never be placed near or over a radiator or heat register This product should not be placed in a built in installation where proper ventilation is not provided This product should be operated only from the type of power source indicated on the marking label If you are not sure of the type of power supply to your home consult your dealer or local power company Do not allow anything to rest on the power cord Do not install this product where the cord might be damaged by anyone walking on it Never push objects of any kind into this product t
18. ail PASSWORD First you must activate and define your voicemail password with the voicemail service provided by your local telephone company Once you have defined your password you can then program it into the 2652 31 Advanced eee Handset and Base Operation From the idle OFF mode press MENU use the D GESB scroll keys to select VOICEMAIL SETUP then press OK The following screen is displayed Use the B scroll keys to select PASSWORD then press OK You will see the following display Press EDIT Enter your password To enter pauses or delete characters use the MORE key When done press SAVE Using the dedicated PLAY KEEP and DELETE keys The 2652 is factory programmed with the appropriate key sequences for PLAY KEEP and DELETE When retrieving voicemail messages you can use the dedicated keys on the Base Unit to access these functions If the default programming for the PLAY KEEP and DELETE keys do not work with your voicemail system you can reprogram the keys using the following steps PLAY Access Key From the idle OFF mode press MENU use the B Gp scroll keys to select VOICEMAIL SETUP then press OK The following screen will be displayed Use the B GB scroll keys to select PLAY then press OK You will see the following display Reprogramming PLAY The default PLAY access number is 1 If this does not match the number provided by your local telephone company you w
19. an then answer the intercom call by pressing any key except OFF and Softkeys To end an intercom call press OFF on the Handset or PAGE or SPEAKER on the Base From Handset to Base Press the INTERCOM key followed by 0 The Base will ring once and then automatically enter intercom mode To end an intercom call press OFF on the Handset or PAGE or SPEAKER on the Base From Handset to Handset Press the INTERCOM key followed by the number of the other Handset you wish to call e g Handset 3 Handset 3 can then answer the intercom call by pressing any key except OFF and Softkey To end the intercom call press OFF on either Handset 27 Advanced EER Advanced ears Handset and Base Operation call ALL from Handset Press the INTERCOM key followed by the All registered Handsets and the Base will ring Any Handset can answer by pressing INTERCOM or the Base can answer by pressing SPEAKER To end the intercom call press OFF on Handset or press SPEAKER on Base Handsfree Speaker Operation Your 2652 Handset has a built in handsfree speaker This feature allows you to stand the Handset upright on a table or desktop and have handsfree conversations For more information refer to MAKING CALLS in HANDSET AND BASE OPERATION To Switch Between Earpiece and Speaker While on a call you can press HANDSFREE to switch to speaker While on a speaker call press HANDSFREE again to the Handset ea
20. er a conference call simply access the line with two or three extensions by pressing ON or HANDSFREE on the Handset or SPEAKER on the Base The phone icon and two or three extension numbers will be displayed in the upper left corner of the Handset Transferring Calls You can transfer calls on the 2652 system from the Base to Handset Handset to Handset or Handset to Base Blind Transfer You can directly transfer any active call to another system extension without notification by doing the following steps Handset or Base must be on an active call Press the INTERCOM key on the handset or PAGE key on the base followed by the number of the Handset 1 2 3 4 or Base 0 that you wish to transfer the call to When the other extension answers the call will automatically be connected to the other extension An unanswered call will ring back to the originating Handset Base if not answered within 30 seconds And if it is still not answered within another 30 seconds the call will automatically be terminated Announced Transfer You can perform an announced transfer call and advise another extension of an active call by following these steps Handset or Base must be on an active call Place the active call on HOLD Press the INTERCOM key on the handset or PAGE key on the base followed by the number of the Handset 1 2 3 4 or Base 0 that you wish to transfer the call to When the other extension an
21. f purchase We will repair or replace at our option this product without charge should it fail due to a defect in material or workmanship within that time period This warranty does not apply to loss or damage that is the result of accident misuse or negligence All other warranties expressed implied or statutory including warranties of fitness for a particular purpose are limited to the time period listed and are otherwise excluded from this warranty if unauthorized repairs are attempted Additionally the Supplier shall not be liable for any incidental or consequential damage or commercial loss nor for any other loss or damages The Supplier assumes no responsibility for products sent without prior return authorization For Warranty service ONLY call 1 800 595 9511 41 Additional Information Additional Information FCC and ACTA Regulations This equipment complies with Parts 15 of the Federal Communications Commission FCC rules for the United States It also complies with regulations RSS210 and CS 03 of Industry and Science Canada Operation is subject to the following two conditions 1 this device may not cause interference and 2 this device must accept any interference including interference that may cause undesired operation of the device Alabelis located on the underside of the Base Unit containing either the FCC registration number and Ringer Equivalence Number REN You must upon request provide this
22. h the charge contacts in the battery compartment Replace the battery compartment cover by sliding it upward Place the Handset in the Charge Cradle and allow it to charge for 10 12 hours After the initial charge a maintenance charge of 8 hours should be sufficient Registration and Operation Enter Base ID Code 1 After charging the Handset remove it from its Charge Cradle the screen will display Press NEW then enter the 15 digit Base Unit ID code located on the underside of the Base Unit Press OK The Handset will display PLEASE WAIT Wait approximately 15 seconds The Handset will display FOUND BASE If the Handset displays SYSTEM IS BUSY PLEASE TRY LATER this indicates that the system is in use Wait until the Base Unit is in the idle on hook mode and repeat steps 2 through 4 Congratulations You can now enjoy the benefits of your multi Handset system 12 Handset and Base Indicators Handset Icons Description Line In Use indicator On steady with no number next to it when a parallel set is in use On steady with one or more numbers next to it indicating which extensions are using the line For example 12 indicates that Handset 1 and Handset 2 are on an outside call Intercomindicator On steady with the extension numbers currently on an intercom call For example 02 indicates that the Base and Handset 2 are on an intercom call Battery indicator
23. he Handset will emit a warning tone whenever the Handset is taken out of range of the Base e KEYPAD TONE Select this option to turn the Keypad tones ON or OFF Press the OFF or ON soft keys to make your selection Press OK to confirm your selection and return to the Handset Settings menu When set to ON the Handset will emit a beep whenever a key is pressed CONTRAST Select this option to adjust the contrast level of the Handset display Use the scroll keys to make your selection The Handset display will automatically adjust as you make your selection Press OK to confirm your selection and return to the Handset Settings menu e LANGUAGE Select this option to change the display to appear in English Spanish or French Use the 3 amp scroll keys to select language then press OK to confirm your choice 17 Range Extender Your 2652 has an enhanced feature that is designed to improve performance This feature is useful if you are using your 2652 in an area with excessive interference or you require a moderate increase in operating range The Range Extender feature can help to improve both the sound quality and range Actual range will depend on your environment To select the Range Extender setting follow these steps In the idle OFF mode press MENU and use the scroll keys to select RANGE EXTENDER then press OK There are 3 option settings in the RANGE EXTENDER menu 1 Select OFF to disable RANGE EXTEND
24. hrough holes and slots in the Handset and Base Unit as they may touch dangerous voltage points or short out parts that could result in a risk of fire or electric shock Never spill liquid of any kind on the product To reduce the risk of electric shock do not disassemble this product but take it to an authorized service facility Opening or removing cabinet parts other than specified access doors may expose you to dangerous voltages or other risks Incorrect reassembling can cause electric shock when the appliance is subsequently used Do not overload wall outlets and extension cords as this can result in the risk of fire or electric shock Important Safety Instructions 12 13 14 Unplug this product from the wall outlet and refer servicing to an authorized service facility under the following conditions A B C D If the product does not operate normally by following the operating When the power supply cord or plug is damaged or frayed If liquid has been spilled into the product If the product has been exposed to rain or water instructions Adjust only those controls that are covered by the operating instructions because improper adjustment of other controls may result in damage and will often require extensive work by an authorized technician to restore the product to normal operation If the product has been dropped and the cabinet has been damaged If the product exhibits a distinct change in performance
25. iate type and size battery pack specified in the instruction manual provided for this product 2 Do not dispose of the battery pack in a fire The cell may explode Check with State and local codes for possible special disposal instructions 3 Do not open or mutilate the battery pack Released electrolyte is corrosive and may cause damage to the eyes or skin It may be toxic if swallowed 4 Exercise care in handling battery in order not to short the battery with conducting materials such as rings bracelets and keys The battery or conductor may overheat and cause burns 5 Charge the battery pack provided with or identified for use with this product only in accordance with the instructions and limitations specified in theinstruction manual 6 Observe proper polarity orientation between the battery pack and battery charger 10 Registration and Operation Registration and Operation of the 2603 Accessory Handset Your 2652 system can operate up to 4 Handsets The accessory Handset consists of the following Handset Belt Clip Battery Pack Charger Unit Setup of the 2603 Accessory Handset 1 11 Plug the AC power adapter into an electrical outlet then the DC connector into the bottom of the Charger Unit Remove the Handset battery compartment cover by pressing on the indent and sliding downward Place the new battery pack in the Handset with the metal contacts aligned wit
26. ill need to edit the number Press EDIT Enter the PLAY access number provided by your local telephone company To enter pauses or delete characters use the MORE key When finished press SAVE 32 Handset and Base Operation KEEP Access Key From the idle OFF mode press MENU use the QD GSB scroll keys to select VOICEMAIL SETUP then press OK The following screen will be displayed Use the B Gp scroll keys to select KEEP then press OK You will see the following display Reprogramming KEEP The default KEEP access number is 2 If this does not match the number provided by your local telephone company you will need to edit the number Press EDIT Enter the KEEP access number provided by your local telephone company To enter pauses or delete characters use the MORE key When finished press SAVE DELETE Access Key From the idle OFF mode press MENU use the QED Gp scroll keys to select VOICEMAIL SETUP then press OK The following screen will be displayed Use the B G scroll keys to select DELETE then press OK You will see the following display Reprogramming DELETE The default DELETE access number is 3 If this does not match the number provided by your local telephone company you will need to edit the number Press EDIT Enter the DELETE access number provided by your local telephone company To enter pauses or delete characters use the MORE key When finished press SAVE
27. key enter the first few chararcters of the name If you make a mistake press the CLR softkey Press FIND to search The closest match in alphabetical order will be displayed Once you find the entry you want simply press ON or HANDSFREE to dial the number To Delete a Number Name Using steps 1 and 2 in To Search For and Dial a Number Name locate the entry you want to delete Press the EDIT softkey The Handset will display 21 MEM Memory Press the DEL softkey The Handset will display To delete the displayed records press THIS To delete all records press ALL If you press ALL The screen will display ARE YOU SURE To confirm the deletion of all records press YES To exit without deleting press NO To Edit a Name or a Number Using steps 1 and 2 in To Search For and Dial a Number Name locate the entry you want to edit Press the EDIT softkey twice Then choose NAME or NUM Using the E softkey move the cursor to the character you want to edit and then enter the corrections as needed Press MORE access DEL BACK and Pause when edit a name SPACE function When finished press the SAVE softkey To exit without saving press OFF When finished the Handset will display the edited entry 22 Base Settings The 2652 Base Unit has several settings that can be adjusted according to your preference and system requirements Select Base Ringer Melody The
28. ment is causing harm to the telephone network the telephone company may temporarily discontinue your telephone service The telephone company is required to notify you before interrupting service If advance notice is not practical you will be notified as soon as possible You will be given the opportunity to correct the problem and the telephone company is required to inform you of your right to file a complaint with the FCC Your telephone company may make changes in its facilities equipment operation or procedures that could affect the proper functioning of this product The telephone company is required to notify you if such changes are planned 5 Hearing aid compatibility If this product is equipped with a corded or cordless handset itis hearing aid compatible 6 Programming testing of emergency numbers If this product has memory dialing locations you may choose to store police fire department and emergency medical service telephone numbers in these locations If you do please keep three things in mind a We recommend that you also write the telephone number on the directory card so that you can still dial the emergency number manually ifthe memory dialing feature doesn t work b This feature is provided only as a convenience and the manufacturer assumes no responsibility for customer reliance upon the memory feature c Testing the emergency telephone numbers you have stored is not recommended 43 Additional Information
29. ne LCD Display Select Off Clear Intercom Billed Services Microphone The Base Unit Layout W GI T a XE NGG Mi SAGES SESr AC Power Jack Phone Cord Jack Page Key Charge Indicator Power Indicator In Use Indicator Delete Key Keep Key Redial Key Flash Key Hold Key Mute Key Play Key Volume Keys Dialing Keys 0 9 Speaker Key Auto Callback Key 3 Way Calling Key Repeat Dialling Key Voicemail Key Charging Contacts Setup Plug the AC power adapter into an electrical outlet and the DC connector into the back of the Base Unit To telephone socket outlet To AC power To telephone jack jack Plug one end of the telephone line cord into the jack on the back of the Base Unit Plug the other end of this cord into the wall jack Connecting to phone line Checking for dial tone After the battery is charged press ON on the Handset The Phone icon will appear on the Handset display and you will hear dial tone If not In Case of Difficulty Tone Pulse selection See BASE SETTINGS for details AN CAUTION Use only the power supply provided with your 2652 Unit IMPORTANT For best performance the 2652 should be installed as follows In an elevated location in the center of the room with no obstructions nearby In a location that is away from other electrical appliances such as microwave
30. ompted to ENTER NAME use the digit keys to spell the name Each press of a particular key causes characters to be displayed in the following order Number Key Characters in order 1 2 3 4 5 6 7 8 9 0 19 MEM Memory To Store a Number Name Starting from the idle screen enter the number you want to store in memory Be sure to include long distance codes and pauses using the Pause softkey if necessary Press OFF to correct if you make mistake Press the MEM softkey NOTE If the memory is full the Handset will display PHONEBOOK IS FULL and exit to the pre dial mode without saving the entry You will then be prompted to ENTER NAME Use the digit keys to spell the name If you make a mistake press the CLR softkey To enter a space press I When finished press SAVE If there is space available in memory the entry will be saved and the Handset will display RECORD ANNOUNCE CID If you want to record Name and Number Announce please follow the steps in Recorda New Name and Number Announce Form New Phonebook Entry on page 34 If not press and hold OFF 20 MEM Memory To Search For and Diala Number Name Starting from the idle screen press the MEM softkey to review memory contents a Using the p Gp softkeys scroll through the memory contents in alphabetical order Or you can press the FIND soft
31. ovens personal computers or televisions Installation of Battery Pack in Handset Follow the steps below 1 Remove battery compartment cover by pressing on the indent and sliding downward 2 Place the new battery pack in the Handset with the metal contacts aligned with the charge contacts in the battery compartment Replace the battery compartment cover by sliding it upwards 4 If the new battery pack is not already charged place the Handset in the Base Unit or a charging stand and allow it to charge for 10 12 hours After initial charge a maintenance charge of 8 hours should be sufficient oP 008 o 00 0 0 00 Oe The original Handset that is shipped with your 2652 system will be automatically registered to the Base This Handset is HANDSET 1 As you register additional Handsets to the system they will be assigned extension numbers in the following order HANDSET 2 HANDSET 3 and HANDSET 4 Whenever a Handset battery pack is installed the Handset will automatically begin SEARCHING FOR BASE if previously registered or it will prompt you to ENTER BASE ID to register the new Handset Spare Battery Charger Power Backup Function The 2652 can use the spare battery in the Base Unit to provide operational backup in the event of a power failure With a fully charged battery pack in the spare battery charger you will still be able to place and receive calls from the Handset for up to 3 hours The
32. phone must be off Press the star key three times The Base will emit a happy tone and the Power and In Use LEDs will flash rapidly Press the 1 2 3 4 5 or 6 keys to select the Ringer Melody After each key press the Base will emit a 1 second preview of the selected ringer To save the selected ringer and exit press To exit without saving press x Select Tone Pulse For Base For Handset The phone must be off Press the star key three times The Base will emit a happy tone and the Power and In Use LEDs will flash rapidly Press the 7 key to toggle between TONE and PULSE dialing mode The In Use LED will toggle ON when TONE is selected and OFF when PULSE is selected To save the TONE PULSE selection and exit press To exit without saving press Press MENU Use the scoll keys to select TONE PULSE then press OK Use the scoll keys to select TONE or PULSE then press OK 23 Base Settings Select Base Ringer Volume and OFF The phone must be off Press the star key three times The Base will emit a happy tone and the Power and In Use LEDs will flash rapidly Press the volume up and down keys y to adjust the Base Ringer volume After each press of the volume keys the Base will emit the selected Ringer and volume setting for one second To turn the Base ringer OFF press the volume down key until no ringer preview is played To save the Ringer Volume selec
33. rpiece 28 Handset and Base Operation Base Speaker Operation The Base of your 2652 is equipped with a full duplex speaker This is a very useful feature for handsfree conversations or conference calls at the Base Unit For more information refer to MAKING CALLS in the HANDSET AND BASE OPERATION section Line in Use Indication On the Handset When the telephone line is currently being used by a system Handset or the 2652 Base a status message similar to this will display on idle Handset s When the telephone line is currently being used by a parallel set a telephone device other than the 2652 on the same line the phone icon will remain on steadily and EXTENSION IN USE will be displayed on the Base When a system Handset or a 2652 Base is currently being used the IN USE LED on the Base will illuminate steadily When a parallel set is currently being used the IN USE LED on the Base will flash Low Battery Indication When a low battery is detected the Battery icon will flash and a warning beep is played The status message LOW BATTERY will also be displayed when the Handset is in idle mode To prevent an unexpected call drop a drained Handset battery should be replaced by a fully charged spare battery 29 Advanced ER Advanced eel Handset and Base Operation Conference Calling The 2652 is capable of supporting conference calls with up to two registered Handsets and the Base Unit To ent
34. s connected Consult the dealer or an experienced radio TV technician for help FCC and ACTA Information If this equipment was approved for connection to the telephone network prior to July 23 2001 it complies with Part 68 of the Federal Communications Commission FCC rules If the equipment was approved after that date it complies with the Part 68 rules and with Technical Requirements for Connection of Equipmentto the Telephone Network adopted by the Administrative Council for Terminal Attachments ACTA We are required to provide you with the following information 1 Product identifier and REN information The label on the back or bottom of this equipment contains among other things an identifier indicating product approval and the Ringer Equivalence Number REN This information must be provided to your local telephone company upon request For equipment approved prior to July 23 2001 the product identifier is preceded by the 42 FCC and ACTA Regulations phrase FCC Reg No and the REN is listed separately For equipment approved after that date the product identifier is preceded by US and a colon and the REN is encoded in the product identifier without a decimal point as the sixth and seventh characters following the colon For example the product identifier US AAAEQ03T123XYZ would indicate an REN of 0 3 The REN is used to determine how many devices you may connect to your telephone line and still have
35. se speaker is in use 14 Soft Menu Functions The 2652 has an advanced design that uses a menu structure and soft keys to access all of the built in features Example of the idle mode display RDL Redial Press RDL to display the last 5 telephone numbers dialed The number on top line is the most recent number dialed Use the EB B scroll keys to select the desired number To dial the number you can simply press the ON or HANDSFREE key To Save Redial to Memory Use the scroll keys to select the desired number Then press SELECT Press SAVE Use the steps from 3 to 5 of To Store a Number Name To Erase Redial Use the scroll keys to select the desired number Then press SELECT Press ERASE MENU With the Handset in the idle OFF mode press the MENU key to access the following options lt CALLS LOG CALLER ID ANNOUNCE CID HANDSET SETTINGS RANGE EXTENDER TONE PULSE REGISTER e VOICEMAIL SETUP Use the B GSB scroll keys to select the desired option then press OK 15 Calls Log Caller ID From the idle OFF mode press MENU use the B GG scroll keys to select CALLS LOG then press OK The Caller ID information of the most recently received call will be displayed To scroll to other records use the aD Gp scroll keys To dial the number displayed you can simply press the ON or HANDSFREE key You can also press the CID key to access
36. set will be muted This is done to limit the effect of background noise Belt Clip The Handset is also equipped with a detachable belt clip Align the pins on the inside edge of the clip with the notches on the sides of the Handset The belt clip should snap securely into place Do not force the connection Advanced sia 37 Additional Information In Case Of Difficulty If you have difficulty operating your phone the suggestions below should solve the problem The Phone Doesn t Work At All Make sure the Power Cord is plugged in Make sure the telephone line cord is plugged firmly into the Base Unit and the telephone wall jack Make sure the batteries are properly charged If the LOW BATTERY message is shown the battery pack needs charging No Dial Tone First check all the suggestions above If you still don t hear a dial tone disconnect the Base Unit from the telephone jack and connect a different phone If there is no dial tone on that phone either the problem is in your wiring or local service Contact your local telephone company You Get Noise Static Or A Weak Signal Even When You re Near The Base Unit Household appliances plugged into the same circuit as the Base Unit can sometimes cause interference Try moving the appliance or the Base Unit to another outlet You Get Noise Static Or A Weak Signal When You re Away From The Base Unit You may be out of range Either move
37. swers the intercom call explain they have an active call waiting Either extension can press the OFF key on the handset or PAGE key on the base to end the intercom call The other extension presses ON or HANDSFREE on the Handset or SPEAKER on the Base to pick up the call on hold 30 Handset and Base Operation Message Waiting When a voicemail is detected the VOICEMAIL key will be illuminated with a flashing yellow LED The LED in the handset will also flash Programming Voicemail Access Once your voicemail access number and password are programmed into the 2652 you can quickly retrieve voicemail messages by pressing the VOICEMAIL key on the base NOTE In order to use these features you must subscribe to and activate voicemail service through your local telephone company VOICEMAIL Access Key From the idle OFF mode press MENU use the GD GEER scroll keys to select VOICEMAIL SETUP then press OK The following screen is displayed Use the B scroll keys to select ACCESS NUMBER then press OK You will see the following display The default voicemail access number is 99 If this does not match the number provided by your local telephone company you will need to edit the number Press EDIT Enter the voicemail access number provided by your local telephone company To enter pauses or delete characters use the MORE key When finished press SAVE You will then need to program your voicem
38. t Tone Pulse 40 Maintenance 24 Select Base Ringer Volume 41 Limited Warranty and OFF 42 FCC and ACTA Regulations 45 Technical Specifications 91 005574 040 000 ISSUE 0 Sprint 2 4GHz DIGITAL SPREAD SPECTRUM CORDLESS TELEPHONE SYSTEM Model 2652
39. them ring when you are called In most but not all areas the sum of all RENs should be five 5 0 or less You may want to contact your local telephone company for more information 2 Connection and use with the nationwide telephone network The plug and jack used to connect this equipment to the premises wiring and the telephone network must comply with the applicable Part 68 rules and technical requirements adopted by ACTA Acomplianttelephone cord and modular plug is provided with this product It is designed to be connected to a compatible modular jack that is also compliant An RJ11 jack should normally be used for connecting to a single line and an RJ14 jack for two lines See Installation Instructions in the user s manual This equipment may not be used with Coin Telephone Lines or with Party Lines If you have specially wired alarm dialing equipment connected to your telephone line ensure the connection of this equipment does not disable your alarm equipment If you have questions about what will disable alarm equipment consult your telephone company or a qualified installer 3 Repair instructions If this equipment is malfunctioning it must be unplugged from the modular jack until the problem has been corrected Repairs to this telephone equipment can only be made by the manufacturer or its authorized agents For repair procedures follow the instructions outlined under the Limited Warranty 4 Rights of the telephone company If this equip
40. tion and exit press To exit without saving press 24 Handset and Base Operation Redial from Base Unit Pp REDIAL Making Calls From the Handset PS Press ON or HANDSFREE to use the Handset Speakerphone feature Dial the phone number OR Dial the phone number first then press ON or HANDSFREE Press OFF to end your call From the Base Unit E SPEAKER Press SPEAKER Dial the phone number Press SPEAKER to end your call Answering Calls From the Handset Press any key except OFF and the softkeys Press OFF to end your call From the Base Unit Fre SPEAKER Press SPEAKER Press SPEAKER to end your call Pressing REDIAL will immediately dial the last number in the Base Unit redial memory Hold down the REDIAL key for more than 2 seconds to erase the contents in redial memory This is to prevent the accidental dialing of the number stored in redial memory 25 Advanced ba Handset and Base Operation Mute Function MUTE During an active call pressing either the MUTE soft key on the Handset or the MUTE key on the Base when in speakerphone mode will disable the microphone Press the MUTE key again to return to normal 2 way conversation Hold Function LF HOLD From the Handset Press the HOLD soft key to place orpo N a call on hold To return to the call voume ress the ON or HANDSFREE key One O Fr ie
Download Pdf Manuals
Related Search