VMT5015 User Manual EN V3.1 - ads-tec
Contents
1. the operating system can be reinstalled by using one of the existing interfaces An external keyboard is required for installation 8 1 INSTALLING THE OPERATING SYSTEM If the device is not equipped with an integrated drive installing the operating system can only be carried out by using the USB interface Procedure for installation USB e The boot drive in the system Bios must be switched to USB in order to boot the device from the USB interface e Restart the device and insert the Windows CD e Windows installation and basic data setup e With devices using a touchscreen the full functionality range or touchscreen drivers and the soft keyboard should be installed If Windows CE net or Windows XPe is used the entire operating system may be completely installed from the USB stick using the respective image The required image can be purchased from the ads tec company or via the ASSIX online portal 30 ads tec GmbH e Raiffeisenstr 14 e 70771 Leinfelden Echterdingen Te Pier User Manual VMT 5015 V3 1 8 2 TOUCHSCREEN DRIVER INSTALLATION Note gt When installing the drivers you have to consider that the touchscreen is connected with the serial interface Touchscreen and PS2 mouse can be used simultaneously Installation must be carried out as described below e Switch on PC and boot e Start the installer file in the touchscreen folder by accessing the service CD with the Windows Explorer e Follow the in2. 7 1 10 ennn Open abs A e Leg GND HED mesana ils TEE Some EGE S Oe A A 1 KE l ponos f i Er K E 66 u d AN ANY il j 14 ads tec GmbH e Raiffeisenstr 14 e 70771 Leinfelden Echterdingen User Manual VMT 5015 V3 1 Bracket for 90 installation The stainless steel bracket for angled installation in a 90 angle allows a flexible use It has four drill holes for fixing the device You can set the angle of the device towards the front or rear in several steps by loosening the self locking screws on both sides in order to set up the angle of viewing al All Ge F 7 GES T i Ih E w F x I db T l i 1 a ai CO E l H d dh wer Tl AEDT I I j l4 II 142 14 E 241 60 ae 50 ken UT OO i Ann Ka HORKORO o em Sg NN i 7 as 395 ads tec GmbH Raiffeisenstr 14 e 70771 Leinfelden Echterdingen 15 PT tec For manufacturing of customer specific brackets you d have to consider that the bolts on the device side are fixed and cannot be removed Customer specific brackets User Manual VMT 5015 V3 1 En Leen se nn N D e ee u i sined ir rir e einki a SO oe N o eop ole Gene e e f n eoe F obdogGDpe Be Oo2t00000000q 209020900048 d DofocGnpnopgeg TODT TOTONGI SE The figure on this page shows a VMT 5012 devic
3. 9 TECHNICAL DETAILS 32 9 1 DISPLAY DATA Display Display colours Touchscreen 9 2 COMPUTER DATA Eltec 15 TFT 1024 x 768 pixels 16 7 million colours max Resistive industrial touchscreen This device may be equipped with the following adsX modules ex factory according to customer requirements VERSION 1 VERSION 2 VERSION 3 Graphic memory Mass storage device Alternatively Interfaces Network Power supply 9 3 GENERAL DATA External dimensions Weight Protection class Power consumption Max switch on current Pentium M 1 1 GHz 256MB 2GB DDR RAM Intel 855 GME Celeron M 1 0 GHz ULV 256MB 2GB DDR RAM Intel 855 GME Celeron M 800 MHz ULV 256MB 2GB DDR RAM Intel 855 GME A maximum of 64 MB shared memory 1x plug in compact flash board 1 8 hard disk with min 20 GB UDMA COM 1 RS232 1x PS2 mouse 1x PS2 keyboard 2x USB 2 0 1x Mini PCI 1x PCMCIA Line Out 2 internal speakers 1x Ethernet 10 100 Mbit RJ 45 Intel 82551QM 24V DC 20 395 mm x 292 mm x 58 mm WxHxD approx 4 8 kg IP 65 25 Watt typical 7 Ampere for 2ms ads tec GmbH e Raiffeisenstr 14 e 70771 Leinfelden Echterdingen Te Pier User Manual VMT 5015 V3 1 10 SERVICE AND SUPPORT The ads tec company and their partner companies offer a comprehensive service and support to your customers providing a quick and professional support in case of any question with respect to ads tec products and
4. ES 19 4 4 CHECK OF READINESS FOR OPERATION NNN 19 5 OPERATION a een 2 5 1 FRONT CONTROL E 20 5 2 SOFT KE VB OAP Dee een ae ie essen 21 5 3 TOU A CREEN ee ee ee essen 22 5 4 STATUS INDICAPORS EE 22 6 ANTERFACES aen ende oO 6 1 INTERFACE CE TUP Sementina ee ran 23 6 2 SERIAL COM INTERFACE RS232 anna a enen ai EEE Inne Een 23 6 3 USB CONNECTIONS san nn Een an a a EE a EAAS 24 6 4 EXTERNAL KENBOARD ea Ee 25 6 5 Kgl 26 ads tec GmbH e Raiffeisenstr 14 e 70771 Leinfelden Echterdingen 3 User Manual VMT 5015 V3 1 TZ tec 6 6 24V DC POWER SUPPLY 6 7 NETWORK CONNECTION RJ45 EN 28 6 8 LINE OUT SOUND ee teneinde nnee 28 6 9 OPTIONAL RADIO NETWORK CARD EE 28 7 M 7 1 HARD DRIVES COMPACT FLASH DRIVES IDE INTERFACE NNN 29 7 2 EXTERNAL Ee 29 8 SOFTWARE amp DRIVER INSTALLATION WEEN 30 8 1 INSTALLING THE OPERATING SYSTEM 30 8 2 TOUCHSCREEN DRIVER INSTALLATION un nn nn nn nun nennen nn nn nn nn nn n nn nn nn RER RER En nn nn nenn nenn nn nn nen 31 8 3 EENEG ege 31 9 EERSTEN DZ 9 1 DISPLAY DATA 9 2 COMPUTER DA A aa ea a area DEE dent nen Rieder 32 9 3 GENERAL DATA 10 SERVICE AND SUPPORT xxx n nk KKK KK KKK RK KR KKK RK KK KKK RK E KKK KKK KKK KN KKK KKK KKK KKK RRE KKK KKK KKK unn OO 10 1 ADS STEG SUPPORT EE EE 33 10 2 COMPANY ADDRESS EEN 33 4 ads tec GmbH e Raiffeisenstr 14 e 70771 Leinfelden Echterdingen Eier User Manual VMT 501 5 V3 1 ABOUT US ads tec GmbH Raiffeisenstr 14 70771 Leinfelden Ech
5. components Since the devices from ads tech company are also used by partner companies these devices might be configured according to customer requirements Should any question or issue with respect to specific configurations and software installations arise it can only be resolved by the system manufacturer For devices not directly purchased from ads tec we cannot be responsible for the support In this case the support is provided by our partner company 10 1 ADS TEC SUPPORT The ads tec support team is available for direct clients from Monday to Friday from 08 30 AM to 05 00 PM using the following phone number Phone 49 0 711 45894 500 Fax 49 0 711 45894 990 Email info ads tec com 10 2 COMPANY ADDRESS ads tec Automation Daten und Systemtechnik GmbH Raiffeisenstra e 14 D 70771 Leinfelden Echterdingen Germany Phone 49 0 711 45894 0 Fax 49 0 711 45894 990 Email info ads tec de Home www ads tec de ads tec GmbH e Raiffeisenstr 14 e 70771 Leinfelden Echterdingen 33
6. interface can be connected by using a commercially available 9 pin SUB D cable PIN NUMBER SIGNAL NAME m N fo o o f A AN K 1 DCD Y leo000 Y RxD TxD DTR GND DSR RTS CTS RI WO OO SION vu B w N Note This interface is not electrically isolated ads tec GmbH e Raiffeisenstr 14 e 70771 Leinfelden Echterdingen 23 User Manual VMT 5015 V3 1 ec 24 6 3 USB CONNECTIONS The USB interfaces are used for connecting peripherals with USB connection The interface complies with the USB 2 0 standard PIN NUMBER SIGNAL NAME 1 VDC 2 D 3 D 4 GND Note The USB interfaces may be locked using the Lock USB software tool You ll find this software and the documentation on the service CD USB CONNECTION ON THE FRONT PANEL One USB interface can be accessed from the front This interface is located under a plastic cover beneath the display The cover has a tab on the right hand side which is used for opening The plastic cover must properly be replaced and carefully closed after using the USB interface since otherwise the protection class of IP65 is no longer ensured ads tec GmbH e Raiffeisenstr 14 e 70771 Leinfelden Echterdingen ec User Manual VMT 5015 V3 1 6 4 EXTERNAL KEYBOARD One mouse and one keyboard can be connected with both existing PS2 connectors These connections are colour coded for proper connection with this device PIN NUMBER SIGNAL NAME 1 Data 2 NC 3 GND 4 5V 5
7. screened plug connectors to be strictly installed as per the instructions contained in the User Manual 1 8 EQUIPMENT VERSIONS The system is available in two equipment versions Platform for use with compact flash memories Platform without any rotating mass storage media hard disks etc including embedded operating systems Windows CE net XP embedded for stationary use in connection with standard Ethernet or radio network cards on portable commissioning and or forklift equipment Platform including hard disks Including hard disks for stationary use e g in manufacturing using standard operating systems 8 ads tec GmbH e Raiffeisenstr 14 e 70771 Leinfelden Echterdingen Te Pier User Manual VMT 5015 V3 1 1 9 SCOPE OF DELIVERY Please check that all of the following components are contained in the packaging e 1 device e 3 pin Feed through connector from Phoenix Contact COMBICON MC 1 5 3 STF 3 81 type already connected with the device socket e Service CD Optional scope of delivery e Operating system e Installation kit e 2 4 GHz WLAN antennas enclosed for b g ads tec GmbH e Raiffeisenstr 14 e 70771 Leinfelden Echterdingen User Manual VMT 5015 V3 1 Te Eer 2 OPERATING INSTRUCTIONS This device contains electrical voltages and extremely sensitive components The manufacturer or a service partner authorised by the manufacturer should be consulted if you plan to make any modifications For this ty
8. storage 20 45 C Because of the integrated max temperature memory e Humidity In operation 10 85 without condensate For storage 10 85 without condensate e Vibrations In operation 1G 10 500 Hz EN 60068 2 6 e Shock resistance In operation 5 G with a half wave of 30 ms duration EN 60068 2 27 ads tec GmbH e Raiffeisenstr 14 e 70771 Leinfelden Echterdingen F2 User Manual VMT 5015 V3 1 Te Eer 1 7 STANDARDS This unit is compliant with the provisions and safety objectives of the following EU Directives e This unit is compliant with the CE mark testing specification limits as defined in the European test standards EN 61000 6 4 und EN 61000 6 2 e This unit is compliant to the DIN EN 60950 VDE0805 IEC950 testing specification limits on Safety of Information Technology Equipment e This unit is compliant to the DIN EN 60068 2 6 sinusoidal vibration testing specification limits e This unit is compliant to the DIN EN 60068 2 27 shock and bump testing specification limits Note A corresponding declaration of conformity is available for competent authorities care of the Manufacturer Said declaration can be viewed at all times upon request For full compliance to the legal requirements in force on electromagnetic compatibility all components and cables used for unit connection must also be compliant with said regulations It is therefore necessary to employ BUS and LAN cables featuring
9. 50V Im SCHT d W beet Hinweis The device can be started with the ignition function 18 ads tec GmbH e Raiffeisenstr 14 e 70771 Leinfelden Echterdingen TZ tec User Manual VMT 5015 V3 1 4 2 CABLE INSTALLATION The power supply connectors and interfaces of this device are installed inside the case Cables can be routed through rubber grommets and exit the case on the bottom The grommets are inserted between the case and the cover and can easily be removed after removing the cover Since this device includes the required input peripherals soft keyboard touch screen only one grommet for the power supply cable cable diameter of 6 mm as well as three blank plugs are integrated by default Should it be required to feed through more cables from the device to the outside these blank plugs must be replaced by suitable grommets optionally available accessories 4 3 ORDER OF COMMISSIONING STEPS e Remove the case cover screws and carefully remove the cover e Fix the wires of the power supply cable in the screw terminals by using wire end sleeves e Plug the data cable connector on the desired interface connector and screw it on if possible e Select a cable grommet with a suitable diameter for each cable to be fed through and enclose the cable with it e Remove the blank plug and replace it with the grommet surrounding the cable e Attach the case cover properly and install the screws The service slot is f
10. Clock 6 NC The control system has a purple coloured 6 pin mini DIN socket PS2 identified as KEYB Any commercially available AT compatible quality keyboard equipped with the required connector can be connected with this socket Check the keyboard for proper function before using it Note Since the timing of the integrated controller is optimised for Cherry keyboards keyboards of this manufacturer should preferably be used If the screen shows that the soft keyboard is active controlling the device by using the external keyboard is possible with restrictions only The keyboard must be connected before switching the device on since the keyboard interface Is initialised while booting If the keyboard is connected during operation of this device and the keyboard was not connected during the booting process it is not operable The device features an keyboard simulator which can be used to connect a scanner ads tec GmbH e Raiffeisenstr 14 e 70771 Leinfelden Echterdingen 25 User Manual VMT 5015 V3 1 ec 6 5 MOUSE The green coloured interface MOUSE is used to connect a mouse Check the mouse for compatibility before using it PIN NUMBER SIGNAL NAME 1 Data 2 NC 3 GND 4 5V 5 Clock 6 NC Note The mouse must be connected before switching the device on since the mouse interface Is initialised while booting If the mouse is connected during operation of this device and the mouse was not connected dur
11. User Manual Version 9 1 veesoe VMT 5013 ads tec GmbH Raiffeisenstr 14 D 70771 Leinfelden Echterdingen Tel 49 0 711 45894 0 Fax 49 0 711 45894 990 mailbox ads tec com http www ads tec com User Manual VMT 5015 V3 1 Et Eiter Copyright ads tec GmbH Raiffeisenstr 14 D 70771 Leinfelden Echterdingen Germany gt ads tec GmbH e Raiffeisenstr 14 e 70771 Leinfelden Echterdingen Te Pier User Manual VMT 5015 V3 1 INDEX ABOUT US EEN 2 1 REMARKS eege eesech 1 1 RELEVANT DOCUMENTATION FOR THIS DEVICE sernnnnnnnnnnnnnn nun nun nn nn nun nn nun nun nn nn nun nun nn nn nun nn nun ann nenn anne nennen 6 1 2 USED SYMBOL EXPLANATION Senne nee een 6 1 3 DATA FIGURES AND ee ten H ie 6 1 4 TRADE MARKS ee ee ee nae ee a ne een ee te nenn 6 1 5 Beie EE 7 1 6 ENVIRONMENTAL CONDITIONS EE 1 EE 8 1 8 EQUIPMENT VERSIONS een ae ee nee engere een 8 1 9 SCOPE OF DEEN ER Vest deet 9 2 OPERATING INSTRUCTIONS NN NRN 10 2 1 OPERATING LOCATION EE EE 10 2 2 DAMAGE CAUSED BY IMPROPER USE Aas NNN KKK KKK NN NNN KKK KN NNN NNN NK NK NK NN KN NN NNN NNN KN NNN KN NNN KKK KN 10 2 3 WARRANTY REPAIR Eden EE Ee 11 3 ENSTALLATION su 0 0 0000 en ae see Be 3 1 INSTALLATION OPTIONS ee ee enter wesen 12 3 2 EXTERNAL DEVICE DIMENSIONS NNN 17 4 Bel EE el dE EENG E 4 1 ANTRE INTER ACE ee 18 4 2 CABLE INSTALLATION een een ne Eee dns 19 4 3 ORDER OF COMMISSIONING STEPS Geesse E ANEA aaa Da EECHER
12. Using the device in non specified environments for example on board ship or in areas that might contain explosive gases or in extreme heights is prohibited Warning The device may only be switched on after acclimatising to the ambient temperature in order to avoid condensate accumulation The same applies if the device has previously been exposed to extreme temperature variations To avoid overheating in operation The device must never be exposed to direct radiation by sunlight or any other light or heat source 2 2 DAMAGE CAUSED BY IMPROPER USE This device must immediately be shut down and protected from any accidental commissioning if the operating system shows any obvious damage caused by for example improper operating or storage conditions or by improper use or handling 10 ads tec GmbH e Raiffeisenstr 14 e 70771 Leinfelden Echterdingen TZ tec User Manual VMT 5015 V3 1 2 3 WARRANTY REPAIR During the warranty period any repair must only be carried out by the manufacturer or by a person authorised by the manufacturer ads tec GmbH e Raiffeisenstr 14 e 70771 Leinfelden Echterdingen 14 User Manual VMT 5015 V3 1 TZ tec 3 INSTALLATION 3 1 INSTALLATION OPTIONS Gallow bracket for Rittal systems The stainless steel installation bracket for gallow type installations CP S CP L has four drill holes By using this bracket the device can be fixed on a gallows You can set the angle of the device towards the
13. Which driver for which device menu item in order to open this file 1 2 USED SYMBOL EXPLANATION Warning The Warning symbol refers to activities which might cause personal injury or damage to the hardware or software Note The Note symbol familiarises you with conditions to be observed in order to ensure flawless operation Additionally hints and advice are given for a more efficient use of the device and for software optimisation 1 3 DATA FIGURES AND MODIFICATIONS All texts data and figures are non binding We reserve the right of modification in accordance with technological progress At that point in time when the products leave our premises they comply with all currently applicable legal requirements and regulations The operator operating company is independently responsible for compliance with and observance of any subsequently introduced technical innovations and new legal requirements as well as for all usual obligations of the operator operating company 1 4 TRADE MARKS We would like to remind you that all software and hardware designations as well as trade names of companies used in this documentation are subject to the general international trade mark brand or patent protection laws WINDOWS WINDOWS CE and WINDOWS CE net are trade marks registered by Microsoft Corp Citrix and ICA are trade marks registered by Citrix Systems Inc Intel and Pentium are trade marks registered by I
14. e The VMT fixing points for a customer specific bracket are the same with all VMT devices ads tec GmbH e Raiffeisenstr 14 e 70771 Leinfelden Echterdingen 16 gt g gt 0 Ka Q D kK 2 gt T J C D 2 Cc d 0 J 3 2 EXTERNAL DEVICE DIMENSIONS JN N 0000 140 83 ads tec GmbH e Raiffeisenstr 14 e 70771 Leinfelden Echterdingen User Manual VMT 5015 V3 1 Et Eiter 4 COMMISSIONING The power supply connection and interfaces of this device are installed inside the case You have to remove the case cover in order to connect the power supply cables and the interface cables All supply leads and all required data leads have to be connected before commissioning Warning The device must be switched off before connecting or disconnecting any cables in order to prevent damage to the electronics The device may only be switched on after acclimatising to the ambient temperature in order to avoid condensate accumulation Make sure to meet the admissible voltage reguirements for this device After switching off and before switching on you must wait for at least 5 seconds Note The screen of a data cable must always be connected with the connector housing EMC Under the embedded operating system interfaces must explicitly be enabled and required drivers must be installed in order to be able to use them 4 1 AVAILABLE INTERFACES OV AIGN 24V Sicherung T6 3H2
15. front or rear in several steps by loosening the self locking screws on both sides in order to set up the angle of viewing E D me E LE Fig TEF TN PFE UE d Es dd Es E gr Es E de KH a T gt J CO 12 ads tec GmbH e Raiffeisenstr 14 e 70771 Leinfelden Echterdingen User Manual VMT 5015 V3 1 Bracket for VESA standard The stainless steel installation bracket for the VESA standard 75mm has four drill holes Using this bracket the device can be fitted to a wall or to a VESA coupler You can set the angle of the device towards the front or rear in several steps by loosening the self locking screws on both sides in order to set up the angle of viewing oe Berater OE EE s kd Goh 8000000 860 666666 HH UN dech w s SS HT m wer 7 Im TIR ef Y r i Kei Y ret i y T EUR Be an Ami OW ewe egy nn a ads tec GmbH e Raiffeisenstr 14 e 70771 Leinfelden Echterdingen 13 User Manual VMT 501 5 V3 1 Desktop bracket The stainless steel bracket for desktop installation has 12 drill holes By using this bracket the device can be fixed to a control stand or desktop You can set the angle of the device towards the front or rear in several steps by loosening the self locking screws on both sides in order to set up the angle of viewing D D D D enon cog gel Pi D l EEEE D EE Dao laan Dapp a EEEIEE EE a E 1 1 7
16. fter another at the soft keyboard and the special keys Shift Alt and Ctrl must always be pushed first Due to differences in programming of a large variety of software we cannot ensure that the soft keyboard works properly with all software When deactivating the soft keyboard the previously active state alphanumeric numeric keys or function keys will be stored and will be displayed when re activating the keyboard ads tec GmbH e Raiffeisenstr 14 e 70771 Leinfelden Echterdingen 21 User Manual VMT 5015 V3 1 Er tec 5 3 TOUCHSCREEN The control system is equipped with an touchscreen The touchscreen is internally connected with a serial interface The driver software required for its use is already integrated in the corresponding operating system or can be installed from the attached service CD 5 4 STATUS INDICATORS SYS LED BICOLOURED Depending on the colour and type of flashing different device states are displayed by the SYS LED The following signals are displayed e LED lights green The device is ready for operation Power ON e LED is off The device is switched off Power OFF 2e ads tec GmbH e Raiffeisenstr 14 e 70771 Leinfelden Echterdingen TZ tec User Manual VMT 5015 V3 1 6 INTERFACES 6 1 INTERFACE SETUP INTERFACE IRQ ADDRESS COM1 4 3F8h COM2 Touch 3 2F8h 6 2 SERIAL COM INTERFACE RS232 The serial interface is used for digital and for analogue data transmission as well The RS 232
17. ing the booting process it is not operable 26 ads tec GmbH e Raiffeisenstr 14 e 70771 Leinfelden Echterdingen Te Pier User Manual VMT 5015 V3 1 6 6 24V DC POWER SUPPLY The power supply voltage is supplied via a feed through clamp including screw connection figure shows socket in the device PIN NUMBER SIGNAL NAME 123 1 24V DC d 2 Ignition contact ei 3 OV DC Voltage tolerance In the equipment version with a 24V DC 20 power supply a DC DC converter is integrated e Input voltage 24V DC 20 Current consumption The current consumption of the device at nominal consumption depends on the equipment version of this device heater WLAN etc e Switch on current 7 Amperes for 2ms e Standby input current 0 1 Ampere e maximum input current using heater 2 5 Amperes e Regular operation 1 5 Amperes without heater Note The typical power consumption of this device is indicated in the Technical details Chapter ads tec GmbH e Raiffeisenstr 14 e 70771 Leinfelden Echterdingen 27 User Manual VMT 5015 V3 1 Et Eiter 6 7 NETWORK CONNECTION RJ45 If the drivers required for functioning are installed on the device the control system may be integrated in an Ethernet network supporting the 10 100 Mbit standard by using the Ethernet 10 100BaseT network connector Specifications of this network topology must be observed in this case You can install the drivers required for functioning from the e
18. ixed with captive screws Warning Full protection according to the indicated protection class is only ensured if the case cover Ze properly installed 4 4 CHECK OF READINESS FOR OPERATION Check the device for any hidden damage caused by improper transport improper operating or storage conditions or by improper use e g smoke development from the device etc Immediately shut down the device and prevent any further accidental commissioning if any damage is detected ads tec GmbH e Raiffeisenstr 14 e 70771 Leinfelden Echterdingen 19 User Manual VMT 501 5 V3 1 Er tec F OPERATION 5 1 FRONT CONTROL KEYS Depending on the equipment version of the device an operating system Windows CE net Windows XP embedded or Windows XP Prof and a soft keyboard might be already installed ex factory The following functions are already assigned to the keys on the front panel by a specific driver in the soft keyboard On Off pushbutton for the device ATX functionality Level 1 Activate and deactivate the soft keyboard for letter character input using the touchscreen Level 2 Increase the volume with devices using a speaker audio output Level 1 Change tasks Alt ESC in Windows Level 2 Decrease the volume with devices using a speaker audio output Level 1 Not connected Level 2 Increase display brightness Level 1 Right mouse key function Level 2 Decrease display brightness Shift key SHIFT fo
19. nclosed service CD should they not be installed on the device PIN NUMBER SIGNAL NAME 18 1 TX e E 2 3 RX 4 NC 5 NC 6 RX 7 NC 8 NC 6 8 LINE OUT SOUND The Line Out connection of this device is a 3 5 mm socket which provides a stereo signal In order to use this connection the matching plug must be wired up as follows PIN NUMBER SIGNAL NAME O a Ground GND R Signal right hand side SE de E L Signal left hand side 6 9 OPTIONAL RADIO NETWORK CARD If a slot with a radio network card and an externally attached antenna is installed in the device and if this card is supported by the corresponding drivers in the operating system this device may be integrated in an Ethernet network supporting 11 Mbit or 54 Mbit 802 11a b g compatible connections Specifications of this network topology must be observed in this case 28 ads tec GmbH e Raiffeisenstr 14 e 70771 Leinfelden Echterdingen ec User Manual VMT 5015 V3 1 7 DRIVES 7 1 HARD DRIVES COMPACT FLASH DRIVES IDE INTERFACE The storage medium is selected according to the customer requirements The following options are available for storage Compact Flash memory Compact flash memories with a storage capacity of at least 64 MB are used The capacity depends on the desired operating system and the additional programmes to be installed Hard disk A 1 8 hard disk with at least 20 GB UDMA is used On delivery the hard disk is formatted in NTFS fo
20. ntel Corp IBM PS 2 and VGA are trade marks registered by IBM Corp 6 ads tec GmbH e Raiffeisenstr 14 e 70771 Leinfelden Echterdingen Te Pier User Manual VMT 5015 V3 1 CompactFlash and CF are trademarks of SanDisk Corp All other nationally and internationally recognised trade marks and product names are hereby likewise recognised 1 5 COPYRIGHTS This manual including all contained figures is protected by copyright law Any use for third parties non compliant with the copyright provisions is prohibited Any reproduction translation as well as electronic and photographic archiving and modification shall only be permitted after explicit written authorisation by ads tec GmbH Any party in violation of this provision shall be obliged to damage compensation 1 6 ENVIRONMENTAL CONDITIONS The device may be operated under the following conditions Failure to observe these specifications will terminate any warranty for this device Ads tec cannot be held liable for any damages arising due to improper use and handling e Temperature for devices including a HDD In operation 0 45 C For storage 20 45 C Because of the integrated max temperature memory e Temperature for devices including a compact flash memory In operation 0 45 C For storage 20 45 C Because of the integrated max temperature memory e Temperature for devices including a heater only CF Devices In operation 20 45 C For
21. pe of work the device must be switched off at the mains and the power lead must be disconnected Suitable measures for avoiding electrostatic discharge towards parts of the components when touching the equipment must be taken If the device is opened by an unauthorised person hazards for the user might arise and any warranty claim will cease General instructions e All users must read this manual and have access to it at all times e Installation commissioning and operation may only be carried out by trained and qualified staff e The security instructions and the manual itself must be observed by all persons who work with this device e At the location of use the valid guidelines and regulations for accident prevention must be observed e The manual contains the most important instructions on how to use this device in a safe way e Appropriate storage proper transport installation and commissioning as well as careful operation are prerequisites for ensuring safe and proper operation of the device Warning Any leads e g power leads interface cables may only be connected if the device is switched off in order to avoid damaging the device 2 1 OPERATING LOCATION The VMT control system is designed for use with support arm systems or on mobile base equipment commissioning trolleys fork lift equipment and similar You have to take care that the environmental conditions indicated in the technical specification are met
22. r activating the second keyboard level This key must be pressed simultaneously with the desired function key Note If the software keyboard is not installed only the functions for display settings and volume control are active The controller display is not output on the display in this case The functions assigned to the keys might already be modified according to customer specifications Above described functions are pre set ex works 20 ads tec GmbH e Raiffeisenstr 14 e 70771 Leinfelden Echterdingen ec User Manual VMT 5015 V3 1 5 2 SOFT KEYBOARD If the operating system is installed ex works the soft keyboard is included in this installation If the device is delivered without any operating system the soft keyboard has to be installed by the customer By using the soft keyboard data can be entered via the touchscreen like with an external keyboard el erdee eee EEE ETA Groe beopobeeb ere eee SDE se el Activate and deactivate the soft keyboard for letter character input using the touchscreen Switches display of numeric keypad on off only if numeric keypad is displayed Switching between representation modes alphanumeric keypad gt numeric keypad gt bar of function keys Soft keyboard representation zoom in Soft keyboard representation zoom out Note If a function is to be activated which requires pressing two keys at the same time e g Alt F4 these keys have to be pushed one a
23. rmat default for Windows XP Note Recommendation for selection of storage media with a basic installation Compact Flash memory Windows CE 5 0 Windows XP embedded Hard disk Windows XP Professional 7 2 EXTERNAL DRIVES By default no drive for removable media CD floppy disk is integrated in the device Additionally the system provides an USB interface with which an external drive could be connected In this case you d have to ensure that the equipment used is suitable for use in an industrial environment Warning Connecting or disconnecting of external drives during operation is inadmissible since it cannot be excluded that the drive is in use at this point in time Data loss might occur if not observed ads tec GmbH e Raiffeisenstr 14 e 70771 Leinfelden Echterdingen 29 User Manual VMT 5015 V3 1 ads 8 SOFTWARE amp DRIVER INSTALLATION The device will be delivered with a pre installed Windows operating system on request by the customer The drivers required for this are already installed and the operating system will be enabled by entering the licence information Should an initial installation be required please adhere to the following steps With a newer operating system like Windows XP the network card and graphics card will properly be recognised during initial installation so that only the touchscreen driver and the soft keyboard must be installed separately Note If the hard drive was formatted
24. structions on screen and agree to the licensing conditions e Once the installer is finished shut down the computer and restart it e After restarting the touchscreen must be calibrated If the driver does not start automatically open the setup menu by using the Start gt Settings gt Control panel gt Elo Touchscreen directory path e Start the touchscreen calibration by using the Calibration data item and push the crosses which appear one after another on the screen If the cursor position coincides with the touch point of your finger on the touchscreen exit the control box by using the OK button 8 3 SOFT KEYBOARD The soft keyboard must be installed from the enclosed CD ROM in order to enable using the 5 keys exception VMT series there are 6 keys underneath the screen Installation must be carried out as described below e Connect the external drive with the device e Switch the PC on and insert the driver CD into the drive after booting e Start the installer from the service CD e Follow the on screen instructions install the driver select the language and confirm that the computer is going to be restarted Note Further settings can be performed with respect to the basic settings of the soft keyboard You ll find information about this in the Readme file in the installation folder for the soft keyboard ads tec GmbH e Raiffeisenstr 14 e 70771 Leinfelden Echterdingen 31 User Manual VMT 5015 V3 1
25. terdingen Tel 49 0 711 45894 0 Fax 49 0 711 45894 990 www ads tec com Germany ads tec GmbH provides large enterprises and globally active corporations with cutting edge technology up to date know how and comprehensive services in the area of automation technology data processing technology and systems engineering AUTOMATION ads tec GmbH implements full automation solutions from planning to commissioning and is specialized in handling and material handling technologies DATENTECHNIK The data systems division develops and produces PC based solutions and offers a broad range of industrial PCs thin clients and embedded systems SYSTEMTECHMNIK ads tec is specialized in modifying and optimizing embedded operating systems and develops software tools to complement its hardware platforms ads tec GmbH e Raiffeisenstr 14 e 70771 Leinfelden Echterdingen 5 User Manual VMT 5015 V3 1 ec 1 REMARKS 1 1 RELEVANT DOCUMENTATION FOR THIS DEVICE The following documents are essential for setting up and operating this device USER MANUAL ON SERVICE CD DOCUMENTATION ON HAND Contains information for installation commissioning and operating the device along with technical data of the device hardware SERVICE CD Contains drivers and the user manual Note The Drivers xx pdf file contains an overview table showing which drivers from the service CD are to be used for which device You must open the
Download Pdf Manuals
Related Search