Home

PNP-64 - Imimg

1. Handshaking Signals The card gives out a BUSY signal When the card is ready to accept a data byte the BUSY line is at about 9 volts When it is unable to accept any data this line goes to about 9 volts Data Voltage RS 232 Levels Serial Interface Connection pa os 3 PIN RELIMATE 9 PIN D TYPE MALE PNP 64 Printer BUSY 3PINRELIMATE PIN RELIMATE 25 PIN D TYPE MALE Note 1 Short Together DCD DTR and DSR on your host connector 2 Transmit data to the Printer after turning on the power and initializing the printer 3 In9 PIN D TYPE MALE Connector DCD DTR DSR have following pin Numbers i DCD 1 ii DTR 4 ili DSR 6 4 In25 PIN D TYPE MALE Connector DCD DTR and DSR Pin Number as follows i DCD 8 ii DTR 20 iii DSR 6 PNP 64 SELECT PRINT MODE COMMAND The format of this command is Esc n 1BH 21H n Depending on logic levels of the bits in n various print formats can be selected Bit7 Bit6 Bit 5 Bit 4 Bit3 Bit 2 Bit 1 BitO 0 O upright 0 Single width 0 Single height 0 0 0 0 29Cols 0 1 inverse 1 Double width 1 Double height 0 0 0 1 42 Cols GRAPHIC MODE It is selected by following command Esc X 4 x y di d2 _ d k 1 dk 1BH 58H 34H x y di d2 d k 1 dk ESCX 4 X Y di d2 d x y Defines a user defined bit image using x 8 dots in horizontal direction and y dots in vertical direction Range Horizontal directions dots x 8 dots
2. User s Manual PNP 64 Panel Printer pt N Ci ne MAXIM PERIPHERALS PVT LTD 101 Pradhan Bidg Aarey Road Near Subway Goregaon East Mumbai 400 063 India Phone 2927 5039 Fax 91 22 2927 50 41 6 E mail support maximppl com PNP 64 INTRODUCTION The PNP 64 is a Plug amp Play type 2 Inch Thermal Panel Printer Module which enables the OEM users to avoid hassles like mounting mechanism paper roll developing control board etc It has following features Compact size Silent printing Easy paper loading Easy Panel Mounting High resolution 203 dpi Low noise FRONT VIEW Top Cover Lever Top Cover Open Feed Button Error LED Control Panel Power LED Data Connector Power Connector PNP 64 SPECIFICATIONS Printing Method Print Width Print Speed Resolutions Paper Loading St Oe SD Character set 8 Fonts 9 Sensors 10 Paper Type 11 Paper Roll 12 Reliability 13 Interface 14 Data Buffer 15 Power 16 Cutter 17 Dimensions Characters per line Direct Thermal Printing 48 mm 50mm per second 203 DPI 8 dots mm Easy Clam Shell type 29 default or 42 96 Characters ASCII As shown below KALOTE 01234567 89 lt gt ABCDEFGHIJKLMNO PQRSTUVWXYZ Imnopaqrstuvwxyz _ abcdefhijk Normal Double Width Double Height amp Quadruple Size No Paper sensor Direct Thermal Paper
3. Where x ranges from 1 to 48 Vertical direction y dots Explanation The graphic pattern to be printed is divided into columns each column of 8 bits In this command x is number of 8 bits columns The maximum value of x is 48D y is total number of rows LINE FEED Sending OAH or ODH will cause the contents of the data buffer if there are any to be printed followed by a line feed If there is no data in the buffer then a simple line feed will occur In graphic mode these will NOT cause line feed They will be interpreted as data bytes PNP 64 COMMAND SETTING Factory Set 1 Start bit 8 Data bit 1 Stop bit No Parity Baud Rate 9 600 bps Any other on request CONNECTORS 6 PIN RELIMATE MALE FOR POWER amp DATA oo 1 Power GND Black 2 5VDC Brown 8 5VDC Red 4 DATA Orange 5 BUSY Yellow 6 GND Green
4. Width 58mm Outer Diameter 40mm MCBF 50 km RS 232C 768 Characters Logic 5VDC 250mA Mechanism 8 2 VDC 1 5A Peak 3A Manual External 80 W x 76 L x 43 H mm Panel Cut out 76 2 x 72mm PNP 64 PRINTER MOUNTNG METHOD 1 User side dimension guide 8024 SECTION A A 2 Mounting flow chart PNP 64 OPERATING CONTROL PANEL Feed Button 1 Press the feed button to advance the paper 2 Feed button can also be used for printing Self Test as follows Hold down the feed button amp turn on the printer with Top Cover closed Indicator Lights 1 Power The Power LED is on when the printer power is on 2 Error The error LED blinks is on when paper is out INSTALLING THE PAPER ROLL Note The printer must be turned off before installing the paper roll 1 Open the printer cover by pulling the lever 2 Insert the paper roll as shown below Correct 3 Pull out the paper until it comes out from the top of the printer Then close the Top Cover IMPORTANT The power supply should be designed to provide an instantaneous peak current of 3 Amps The 8 5 Volts power supply to the print head should not be applied in the absence of the 5 Volts Logic power supply PNP 64 SERIAL INTERFACE 1 eo N Baud Rates 9600 Factory set Any other on special request Data Length 8 Bits Factory set Data Buffer 768 Characters Parity setting Absent Factory set

PNP-64 - Imimg

Contents

Download Pdf Manuals

Related Search

Related Contents