Industrial Ethernet 6
Contents
1. Removal Removing Lynx with integrated DIN clip Press down the support at the back of the unit using a screwdriver See figure in Cooling This unit uses convection cooling To avoid obstructing the airflow around the unit use the following spacing rules Minimum spacing 25 mm 1 0 inch above below and 10 mm 0 4 inches left right the unit Spacing is recommended for the use of unit in full operating temperature range and service life 18 6643 22001 Getting Started This product runs Westermo Operating System WeOS which provides several management tools that can be used for configuration of the unit e IPConfig tool This is a custom Westermo tool used for discovery of attached Westermo units e Web Configuration of the unit using the web browser e CLI Configuration of the unit via the Command Line Interface Username admin Password westermo If the computer is located in the same subnet as the switch you can easily use a web browser to configure the unit Within the web you can configure most of the available functions For advanced network settings and more diagnostic information please use the CLI Detailed documentation is available in the chapter The Command Line Management Tool in the WeOS management guide Factory default IP address 192 168 2 200 Netmask 255 255 255 0 Gateway Disabled N2. to be placed in an environment classified as ISA S71 04 class G3 Notice Note If the product is placed in a corrosive environment it is important that all un used connector sockets are protected with a suitable plug in order to avoid corrosion attacks on the gold plated pins in connectors 6643 22001 9 Declaration of Conformity Vuwesterma Westermo Teleindustri AB Declaration of conformity The manufacturer Westermo Teleindustri AB SE 640 40 Stora Sundby Sweden Herewith declares that the product s Type of product Model Industrial Ethernet 6 port Switch Lynx L 06 F2G EX is in conformity with the following EC directive s No Short name 2004 108 EC Electromagnetic Compatibility EMC 2011 65 EU Restriction of the use of certain hazardous substances in electrical and electronic equipment RoHS References of standards applied for this EC declaration of conformity No Title Issue EN 61000 6 1 Electromagnetic compatibility Immunity for residential 2007 environments EN 61000 6 2 Electromagnetic compatibility Immunity for industrial 2005 environments EN 61000 6 3 Electromagnetic compatibility Emission for residential 2007 environments A1 2011 EN 61000 6 4 Electromagnetic compatibility Emission for industrial 2007 environments A1 2011 EN 55024 Information technology equipment Immunity 1998 A1 2001 A2 2003 EN 55022 Information techno
3. 20 km 1310 nm 1100 0133 SLC40 monomode connecteur LC 40 km 1310 nm 1100 0134 SLC80 monomode connecteur LC 80 km 1550 nm 1100 0140 SLC120 monomode connecteur LC 120 km 1550 nm Transmetteurs Bi Di 100 Mbit 1100 0145 SLC15 Bi Di A monomode Bi Di 20 km 1310 nm TX 1550 nm RX 1100 0146 SLC15 Bi Di B monomode Bi Di 20 km 1550 nm TX 1310 nm RX 1100 0152 MLC2 BiDi A multimode Bi Di 2 km 1310 nm TX 1550 nm RX 1100 0153 MLC2 BiDi B multimode Bi Di 2 km 1550 nm TX 1310 nm RX Transmetteurs SFP 1 Gbit 1100 0144 GMLC550 SX multimode connecteur LC 550 m 850 nm SX 1100 0147 GMLC2 SX multimode connecteur LC 2 km 1310 nm SX 1100 0141 GSLC10 LX monomode connecteur LC 10 km 1310 nm LX 1100 0142 GSLC50 XD monomode connecteur LC 50 km 1550 nm XD 1100 0143 SLC80 monomode connecteur LC 80 km 1550 nm ZX 1100 0171 GSLC110 monomode connecteur LC 110 km 1550 nm EZX Transmetteurs Bi Di 1 Gbit 1100 0156 GSLC20 BiDi A monomode Bi Di 20 km 1310 nm TX 1490 nm RX 1100 0157 GSLC20 BiDi B monomode Bi Di 20 km 1490 nm TX 1310 nm RX Transmetteurs cuivre 1 Gbit 1100 0148 GC100 cuivre RJ45 100 m 1000BaseT 6643 22001 Maintenance No maintenance is required as long as the unit is used as intended within the specified conditions Agency approvals an
4. option approved transceivers AA VEN jp SFP Transceivers 100 Mbit 1100 0131 MLC2 Multimode LC Connector 2 km 1310 nm 1100 0132 SLC20 Singlemode LC Connector 20 km 1310 nm 1100 0133 SLC40 Singlemode LC Connector 40 km 1310 nm 1100 0134 SLC80 Singlemode LC Connector 80 km 1550 nm 1100 0140 SLC120 Singlemode LC Connector 120 km 1550 nm BiDi Transceivers 100 Mbit 1100 0145 SLC15 BiDi A Singlemode BiDi 20 km 1310 nm TX 1550 nm RX 1100 0146 SLC15 BiDi B Singlemode BiDi 20 km 1550 nm TX 1310 nm RX 1100 0152 MLC2 BiDi A Multimode BiDi 2 km 1310 nm TX 1550 nm RX 1100 0153 MLC2 BiDi B Multimode BiDi 2 km 1550 nm TX 1310 nm RX SFP Transceivers 1 Gbit 1100 0144 GMLC550 SX Multimode LC Connector 550 m 850 nm SX 1100 0147 GMLC2 SX Multimode LC Connector 2 km 1310 nm SX 1100 0141 GSLC10 LX Singlemode LC Connector 10 km 1310 nm LX 1100 0142 GSLC50 XD Singlemode LC Connector 50 km 1550 nm XD 1100 0143 GSLC80 ZX Singlemode LC Connector 80 km 1550 nm ZX 1100 0171 GSLC110 EZX Singlemode LC Connector 110 km 1550 nm EZX BiDi Transceiver 1 Gbit 1100 0156 GSLC20 BiDi A Singlemode BiDi 20 km 1310 nm TX 1490 nm RX 1100 0157 GSLC20 BiDi B Singlemode BiDi 20 km 1490 nm TX 1310 nm RX 1100 0148 Copper Transceiver 1 Gbit
5. 0 hours Vibration IEC 60068 2 6 Operating 3 13 2 Hz 1mm 5 5 30 Hz 1 5 g sine 13 2 100 Hz 0 7 g 30 50 Hz 0 42 mm 50 500 Hz 4 2 g Shock IEC 60068 2 27 Operating 30 g 11 ms 100 g 6 ms Bump IEC 60068 2 27 Operating 10 g 11 ms Packaging Enclosure EN 60950 1 Zinc Fire enclosure Dimension W x H x D 52 5 x 100 x 101 mm With connectors 52 5 x 119 x 101 mm Weight 0 7 kg Degree of protection EN 60529 Enclosure IP 40 Cooling Convection Refer to Safety section Might require Ethernet cables to be fastened close to the unit 6643 22001 Description L106 F2G EX L206 F2G EX is an Industrial switch made for harsh enviroments The switch can be used in either 100 Mbit or Gigabit networks due to our multi rate SFP solution L106 F2G EX L206 F2G EX can also be used together with our previous Lynx series of switches Our unique FRNT Fast Recovery of Network Topology technology is the fastest protocol on the market to re configure a network in the event of any link or hardware failure That is why our products are used in safety critical applications such as tunnels traffic signal control and railway systems Installations in harsh environments and places with heavy electrical interference require the use of a reliable media Lynx provides a number of solutions using fibre optic trans ceivers Multi or singlemode transceivers can be used to build point to point or redundant ring networks with
6. 12ATEX0119X Normes EN 60079 0 2012 EN 60079 15 2010 EN 60079 28 2007 Code de certification Ex nA op is T4 IIC T3 Gc 40 C lt Ta lt 70 C Code ATEX x 11 3G Conditions sp ciales d utilisation L quipement doit tre install dans une zone o le degr de pollution ne d passe pas le degr 2 conform ment l IEC EN 60664 1 et dans un bo tier qui fournit un niveau de protection au moins gal IP54 et conforme aux exigences applicables EN 60079 0 et EN 60079 15 Toutes les connexions externes l quipement et le cas ch ant les modules SFP ne doi vent pas tre ins r s ou retir s sauf si la zone dans laquelle l quipement est install est reconnue comme non dangereuse ou si les circuits raccord s sont hors tension Une fois les c bles r seau install s ils doivent tre correctement fix gr ce des atta ches de c bles ou autre l ment semblable afin de r duire le risque de d branchement accidentel Param tres d entr e des quipements Connecteur d alimentation DC1 DC2 amp COM Double entr e d alimentation 24 V 48 VCC Connecteur E S Statut et Statut et Entr e digitale et Entr e digitale Tension maximale I P 60 VCC 6643 22001 7 Ex Transmetteurs optionnels SFP certifi s Transmetteurs SFP 100 Mbit 1100 0131 MLC2 multimode connecteur LC 2 km 1310 nm 1100 0132 SLC20 monomode connecteur LC
7. 310 nm 1100 0132 SLC20 Singlemode LC Anschluss 20 km 1310 nm 1100 0133 SLC40 Singlemode LC Anschluss 40 km 1310 nm 1100 0134 SLC80 Singlemode LC Anschluss 80 km 1550 nm 1100 0140 SLC120 Singlemode LC Anschluss 120 km 1550 nm BiDi Trans ceiver 100 Mbit 1100 0145 SLC15 BiDi A Singlemode BiDi 20 km 1310 nm TX 1550 nm RX 1100 0146 SLC15 BiDi B Singlemode BiDi 20 km 1550 nm TX 1310 nm RX 1100 0152 MLC2 BiDi A Multimode BiDi 2 km 1310 nm TX 1550 nm RX 1100 0153 MLC2 BiDi B Multimode BiDi 2 km 1550 nm TX 1310 nm RX SFP Transceiver 1 Gbit 1100 0144 GMLC550 SX Multimode LC Anschluss 550 m 850 nm SX 1100 0147 GMLC2 SX Multimode LC Anschluss 2 km 1310 nm SX 1100 0141 GSLC10 LX Singlemode LC Anschluss 10 km 1310 nm LX 1100 0142 GSLC50 XD Singlemode LC Anschluss 50 km 1550 nm XD 1100 0143 GSLC80 ZX Singlemode LC Anschluss 80 km 1550 nm ZX 1100 0171 GSLC110 EZX Singlemode LC Anschluss 110 km 1550 nm EZX BiDi Trans ceiver 1 Gbit 1100 0156 GSLC20 BiDi A Singlemode BiDi 20 km 1310 nm TX 1490 nm RX 1100 0157 GSLC20 BiDi B Singlemode BiDi 20 km 1490 nm TX 1310 nm RX Kupfer Tra 1100 0148 nsceiver 1 Gbit GC100 Kupfer RJ45 100 m 1000BaseT 6643 22001 x Certification ATEX b Num ro de certification ATEX Baseefa
8. GC100 Copper RJ45 100 m 1000BaseT 6643 22001 Ex ATEX Zertifizierung ATEX Zulassungsnummer Baseefa12ATEX0119X Standards EN 60079 0 2012 EN 60079 15 2010 EN 60079 28 2007 Zertifizierungscode Ex nA op ist T4 IIC T3 Gc 40 C lt Ta lt 70 C ATEX Code d 11 3G Spezifische Einsatzbedingungen Die Ger te miissen in einem Bereich welcher einem maximalen Verschmutzungsgrad der Stufe 2 gem IEC EN 60664 1 entspricht und in einem Geh use das einen Schutzgrad von mindestens IP54 bietet und die relevanten Anforderungen von N 60079 0 und EN 60079 15 erf llt installiert werden Alle u eren Anschl sse des Ger tes und auch die SFP Module d rfen nur dann verbun den oder getrennt werden wenn entweder der Bereich in dem das Ger t installiert ist nachweislich ungef hrlich ist oder die verbundenen Stromkreise spannungsfrei sind Die Netzwerkkabel missen nach der Installation mithilfe von Kabelbindern oder hnli chem Material ordnungsgem befestigt werden um ein versehentliches Abziehen der Stecker zu verhindern Eingangsparameter der Ger te Stromversorgung DC1 DC2 amp COM Betriebsspannungsbereich 24 V to 48 VDC I O Anschluss Status amp Status und Digital in und Digital in Maximale I P Spannung 60 VDC 6643 22001 Ex F r SFP Option zugelassene Transceiver SFP Transceiver 100 Mbit 1100 0131 MLC2 Multimode LC Anschluss 2 km 1
9. User Guide 6643 22001 i LI Westermo Teleindustri AB Lynx L106 F2G EX L206 F2G EX Industrial Ethernet 6 port Switch www westermo com Safety Warning Do not open connected unit Hazardous voltage may occur within this unit when connected to power supply Note that this unit can be connected to two different power sources When this unit is operated at an ambient temperature above 55 C 131 F the External Surface of Equipment may exceed Touch Temperature Limit according to EN IEC UL 60950 1 To reduce the risk of fire use only No 26 AWG or larger telecommunication line cord For more information see General safety 100 5001 License Information This device contains public available software which is under the GPL license For more information see legal pdf included with all firmware releases This product includes software developed by the OpenSSL Project for use in the OpenSSL Toolkit http www openssl org Legal information The contents of this document are provided as is Except as required by applicable law no warranties of any kind either express or implied including but not limited to the implied warranties of merchantability and fitness for a particular purpose are made in relation to the accuracy and reliability or contents of this document Westermo reserves the right to revise this document or withdraw it at any time without prior notice Under no circumstances shall Westermo be res
10. al ports 2 kV Earth port 1 kV Surge EN 61000 4 5 Power port L E 0 5 kV 12 0 9 uF L L 0 5 kV 2 Q 18 uF L E 2 kV 42 O 0 5 uF L L 2 kV 42 O 0 5 uF L E 2 kV 120 9 uF L L 1 kV 12 Q 9 uF Signal ports L E 1 kV 2 Q L E 2 kV 420 0 5 uF Power frequency magnetic field EN 61000 4 8 Enclosure 300 A m 0 16 7 50 Hz Pulsed magnetic field EN 61000 4 9 Enclosure 300 A m Radiated RF immunity EN 61000 4 3 Enclosure 10 V m 80 800 MHz 20 V m 800 1000 MHz 10 V m 1400 2100 MHz 5V m 2100 2500 MHz 1 V m 2500 2700 MHz 1 kHz sine 80 AM Conducted RF immunity EN 61000 4 6 Power port 10 V 80 AM 1 kHz 0 15 80 MHz Signal ports 10 V 80 AM 1 kHz 0 15 80 MHz Earth port 10 V 80 AM 1 kHz 0 15 80 MHz Radiated RF emission EN 55022 Enclosure Class A FCC Part 15 Class A Conducted RF emission EN 55022 Power port Class B Signal ports Class B Dielectric strength EN 60950 1 Power port to all 1 5 kVrms 50 Hz 1 min Signal ports to all other ports 1 5 kVrms 50 Hz 1 min Environmental Temperatures Operating 40 to 70 C 40 to 158 F Storage and transport 50 to 85 C 58 to 185 F Humidity Operating 5 to 95 relative humidity Storage and transport 5 to 95 relative humidity Altitude Operating 2 000 m 70 kPa Service life Operating 10 year Reliability prediction MTBF MIL HDBK 217F Operating 615 00
11. ax 46 16 42 80 01 E mail info westermo com www westermo com Sales Units Westermo Data Communications China North America United Kingdom sales cn westermo com www cn westermo com France infos westermo fr www westermo fr Germany info westermo de www westermo de info westermo com www westermo com Singapore sales Qwestermo com sg www westermo com Sweden info sverige westermo se www westermo se sales westermo co uk www westermo co uk Other Offices OM AO 1 For complete contact information please visit our website at www westermo com contact REV A 6643 22001 or scan the QR code with your mobile phone 2013 12 Westermo Teleindustri AB Sweden A Beijer Electronics Group Company
12. ble Not required except when installed in Railway applications as signalling and telecommunications apparatus and located close to rails Conductive housing Yes Number of ports 4 Refer to Safety section To minimise the risk of interference a shielded cable is recommended when the cable is located inside 3 m boundary or the cable is longer than 30 m and inside 10 m boundary to the rails and connected to this port Ethernet SFP pluggable connections FX or TX Electrical specification IEEE std 802 3 2005 Edition Data rate 100 Mbit s or 1000 Mbit s transceivers supported Duplex Full or Auto depending on transceiver Transmission range Depending on tranceiver Connection SFP slot holding fibre transceiver or copper transceiver Number of ports 1or2 6643 22001 13 I O Relay output Maximum voltage current 60 VDC 80 mA Contact resistance Max 30 Q Isolation to All other Connection Detachable screw terminal Connector size 0 2 2 5 mm AWG 24 12 I O I Digital input Maximum voltage load current 60 VDC 2 mA Voltage levels Logic one gt 12V Logic zero lt 1V Isolation to All other Connection Detachable screw terminal Connector size 0 2 2 5 mm AWG 24 12 USB Electrical specification USB 2 0 host interface Data rate Up to 12 Mbit s full speed mode Circuit type SELV Maximum
13. ceived data No 3 RD In Out Transmitted Received data No 4 Not Connected He a 4uVis No 5 Not Connected 20 mA Data rate 10 100 Mbit s No 6 Transmitted Received data No 7 No 8 Not Connected Shield Connected to PE Not Connected Galvanically isolated via signal transformers and capacitively isolated to GND PE through a 2kV 1000pF capacitor See user manual for proven transient protection I O connection for details see page 10 and 12 Console port Cable 1211 2027 for details see page 10 and 12 Connection to console port The console port can be used to connect to the CLI Command Line Interface The following steps needs to be taken 1 Connect the serial diagnostic cable to the console port use only Westermo cable 1211 2027 2 Connect cable to your computer USB port if drivers are needed they can be downloaded from our Web page 3 Use a terminal emulator and connect with correct speed and format 115200 8N1 to the assigned port Bottom view For more information about the CLI see the WeOS management guide 6643 22001 15 Safety control drawing Power connection 4 position Herel Direction Description Input values marking 1 No 1 DC1 Input Supply voltage input DC1 2 3 No 2 DC2 Input Supply voltage input DC2 Uin 19 60 VDC 4 lin 330 mA 24VDC No 3 COM Input C
14. d standards compliance Type Approval Compliance EMC EN 61000 6 1 Immunity residential environments EN 61000 6 2 Immunity industrial environments EN 61000 6 4 Emission industrial environments EN 55022 A1 Emission IT equipment EN 55024 Immunity IT equipment FCC part 15 Class A EN 50121 4 Railway signalling and telecommunications apparatus IEC 62236 4 Railway signalling and telecommunications apparatus Safety UL IEC EN 60950 1 IT equipment Marine DNV Standard for Certification no 2 4 Ex EN 60079 0 EN 60079 15 and EN 60079 28 FCC Part 15 105 This equipment has been tested and found to comply with the limits Notice for a Class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interfer ence when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio com munications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense Corrosive This product has been successfully tested in a corrosion test according to environment IEC 60068 2 60 method 3 This means that the product meets the requirements
15. logy equipment Emission 2006 A1 2007 EN 50121 4 Railway applications Electromagnetic compatibility 2006 Emission and immunity of the signalling and telecommunications apparatus EN 60079 0 Explosive atmospheres 2012 Equipment General requirements EN 60079 15 Electrical apparatus for explosive gas atmospheres 2010 Construction test and marking of type of protection n EN 60079 28 Explosive atmospheres Protection of equipment and 2007 transmission systems using optical radiation The last two digits of the year in which the CE marking was affixed 13 Signature Fr Pierre berg Technical Manager 08 December 2013 1 5 op k indicati A ago The first in the model name can be any alphanumeric character indicating software version The second in the model name can be any alphanumeric characters indicating customer specific models or blank Org nr Postadress Postal address Tel Telefax Postgiro Bankgiro Corp identity number Registered office S 640 40 Stora Sundby 016 428000 016 428001 52 7279 4 5671 5550 556361 2604 Eskilstuna Sweden Int 46 16428000 Int 46 16428001 10 6643 22001 Type tests and environmental conditions Environmental phenomena Basic standard Description Test levels other ports ESD EN 61000 4 2 Enclosure Contact 6 kV Air 8 kV Fast transients EN 61000 4 4 Power port 2 kV Sign
16. ommon Pin 8W 24 VDC No 4 COM Input Common Lynx supports redundant power connection The positive inputs are DC1 and DC2 the negative input for both supplies are COM Connect the primary voltage e g 24 VDC to the DC1 pin and return to one of the COM pins on the power input I O connection 4 position a Direction Description Input Output values 1 No 1 Status Output Alarm relay status contact U 60 VDC max No 2 Status Output Alarm relay status contact lip 80 mA max i No 3 Digital in Input Digital in U n 60 VDC max No 4 Digital in Input Digital in lin 2 mA max The Status output is a potential free opto isolated normally closed solid state relay This can be configured to monitor various alarm events within the Lynx unit see WeOS Management Guide An external load in series with an external voltage source is required for proper functionality For voltage current ratings see Interface Specification section Console port Position Direction description Input output values No 1 In out GND U 3 3 VDC max No 2 Out Tx 24 mA max No 3 In Rx Direction relative to this unit The Digital in is an opto isolated digital input which can be used to monitor external events For volt age current ratings see Interface Specification section 16 External Load Stat
17. oss over cable when connecting the ports Power on the unit Wait for the unit to start up Control that the ON LED is flashing red The ON LED flashing indicates that the unit is now ready to be reset to factory default You now have the choice to go ahead with the factory reset or to skip factory reset and boot as normal e Go ahead with factory reset Acknowledge that you wish to conduct the factory reset by unplugging the Ethernet cables The ON LED will stop flashing This initiates the factory reset process and the unit will restart with factory default settings When the switch has booted up the ON LED will show a green light and is now ready to use e Skip the factory reset To skip the factory reset process just wait for approximately 30 seconds after the ON LED starts flashing RED without unplugging the Ethernet cables The switch will conduct a normal boot with the existing settings Note Do not power off the unit while the factory reset process is in progress 6643 22001 Dimensions Measurements are stated in millimeters IUU TI Max 7 5mm Min 4mm 6643 22001 21 UwesTermo Westermo SE 640 40 Stora Sundby Sweden Tel 46 16 42 80 00 F
18. ote If you are not sure about the subnet consult your network administrator Configuration Configure the unit via Web browser The unit can easily be configured via a Veb browser Open the link http 192 168 2 200 in your web browser and you will be prompted with a Login screen where the default settings for Username and Password are Username admin Password westermo Once you have logged in you can use the extensive integrated help function describing all configuration options Two common tasks when configuring a new switch are to assign appropriate IP settings and to change the password of the admin account The password can be up to 64 characters long and should consist of printable ASCII characters ASCII 33 126 Space is not a valid password character Note Version of IP Config tool must be 10 3 0 or higher 6643 22001 19 Referring documents Type Description Document number Management Guide Westermo OS management guide 6101 3201 Factory default on L106 F2G EX L206 F2G EX It is possible to set the unit to factory default settings by using two straight standard Ethernet RJ 45 cables 1 2 20 Power off the switch and disconnect all Ethernet cables copper and fibre Connect one Ethernet cable between Ethernet ports 3 and 6 and the other between Ethernet ports 4 and 5 The ports need to be connected directly by an Ethernet cable i e not via a hub or switch Use a straight cable not a cr
19. ponsible for any loss of data or income or any special incidental and consequential or indirect damages howsoever caused More information about Westermo can be found at the following Internet address http www westermo com 2 6643 22001 Ex ATEX certification ATEX certification number Baseefa12ATEX0119X VIN IN N A Standards EN 60079 0 2012 EN 60079 15 2010 EN 60079 28 2007 Certification code Ex nA op is T4 IIC T3 Gc 40 C lt Ta lt 70 C ATEX code d 11 3G Specific Conditions of Use The equipment must be installed in an area of not more than pollution degree 2 in accordance with IEC EN 60664 1 and in an enclosure that provides a minimum degree of protection of at least IP54 and complies with the relevant requirements of EN 60079 0 and EN 60079 15 All external connections to the equipment and where applicable the SFP modules must not be inserted or removed unless either the area in which the equipment is installed is known to be non hazardous or the circuits connected have been de energized The network cables once installed must be properly fixated by the use of cable ties or similar to reduce the risk of accidently withdrawing the plugs Equipment input parameters Power Connector DC1 DC2 amp COM Working Voltage Range 24V to 48 VDC I O Connector Status amp Status and Digital in and Digital in Maximum I P Voltage 60 VDC 6643 22001 3 Ex SFP
20. ranges up to 120 km between each switch Our BIDI transceiver which transmits and receives data on a single fibre can be used in applications where the number of fibre cores are limited Real time properties are implemented in the switch in order to achieve determinism for real time critical applications Lynx supports QoS Quality of Service with four priority queues and strict priority scheduling as well as HoL Head of Line Blocking Prevention All to assure that the data network is deterministic 12 6643 22001 Interface specifications Power Operating voltage Rated 24 to 48 VDC Operating 19 to 60 VDC Rated current 180 mA 330 mA 24 VDC with 500 mA USB load 90 mA 170 mA Q 48 VDC with 500 mA USB load Rated frequency DC Inrush current l2t 22 7 10 3 A2s 48 VDC Startup current 2 x Rated current Polarity Reverse polarity protected Redundant power input Yes Isolation to All other Connection Detachable screw terminal Connector size 0 2 2 5 mm AWG 24 12 Shielded cable Not required External supply current capability for proper start up Ethernet TX Electrical specification IEEE std 802 3 2005 Edition Data rate 10 Mbit s 100 Mbit s manual or auto Duplex Full or half manual or auto Circuit type TNV 1 Transmission range Up to 150 m with CAT 5e cable or better Isolation to All other Connection RJ 45 auto MDI MDI X Shielded ca
21. supply current 500 mA Connection USB receptacle connector type A Console Electrical specification TTL level Data rate 115 2 kbit s Data format 8 data bits no parity 1 stop bit no flow control Circuit type SELV Connection 2 5 mm jack use only Westermo cable 1211 2027 SFP Transceivers Supported transceivers Firmware prior to 4 4 0 accepts Westermo branded transceivers only From 4 5 0 other transceivers are accepted with a notice and the unit will no longer be UL approved Temp specifications are also depending on the used transeivers Note To comply with UL60950 1 only UL recognized SFP transceivers should be used Deviations With copper transceiver 1100 0148 the specified operating temperature on Lynx is 0 to 50 C 32 to 122 F FRNT reconfiguration times can not be guaranteed with copper transceivers 14 6643 22001 Safety control drawing Location of interface ports and LED s LED Indicators for details see page 13 Power connection for details see page 12 USB Position Direction description Output values 1 Out VBUS 2 In out D 3 In out D Ubut 5 VDC max 4 GND lout 500 mA max Shield PE SFP transceivers for details see page 4 and 10 Ethernet connection TX 4 ports Position Signale Direction Description Input output values No 1 TD In Out Transmitted Received data g No 2 TD In Out Transmitted Re
22. us Digital In 6643 22001 LED indicators LED Status Description ON OFF Unit has no power GREEN All OK no alarm condition RED Alarm condition or until unit has started up Alarm conditions are configurable see WeOS Management Guide BLINK Location indicator Here I am Activated when connected to IPConfig Tool or upon request from Web or CLI DC1 OFF Unit has no power GREEN Power OK on DC1 RED Power failure on DC1 DC2 OFF Unit has no power GREEN Power OK on DC2 RED Power failure on DC2 FRNT OFF FRNT disabled GREEN FRNT OK RED FRNT Error BLINK Unit configured as FRNT Focal Point RSTP OFF RSTP disabled GREEN RSTP enabled BLINK Unit elected as RSTP STP root switch USR1 OFF GREEN Configurable see WeOS Management Guide RED 1t06 OFF No Link GREEN Link established GREEN Data traffic indication FLASH YELLOW Port alarm and no link Or if FRNT or RSTP mode port is blocked 6643 22001 Muwesterme oc1 ped Fant di 0 RSTP ung fi PE Lynx pss 3 lt gt 5 4 lt gt 6 17 Mounting This unit should be mounted on 35 mm DIN rail which is horizontally mounted inside an apparatus cabinet or similar It is recommended that the DIN rail is connected to ground Snap on mounting see figure Mounting Lynx with integrated DIN clip Aa
Download Pdf Manuals
Related Search