Link Gate A Premium
Contents
1. Analog GSM Gateway Link Gate A Premium BLINK COM gd User manual v1 0 BASIC FEATURES Link Gate A Premium is dual band GSM Gate based on Telit GL865 GSM module equipped by a lot of adjustable features increased comfort of service It has been designed for GSM network 850 900 1800 1900 MHz e Polarity reversal of telephone line allows exact detection of start and end of call e CLIP support all ordinary protocols and allows send not only incoming call number but also name when is saved in phonebook Call billing allows control exact call duration due tax pulses 12 16 kHz 1 pulse when outgoing call is picked up e Beep in minute period into the call allows easy identification of GSM call e Monitoring system allows sending SMS to preprogrammed number when voltage of backup batterie is low unit is logged to GSM network no picks up number of ringing called person connected device doesnt react for ringing etc e ECHO canceler setting up of local conditions Option e USB cable with PC software allows you easy configuration as same as sending and receiving SMS messages via SMS mail software or data transmission e Sending of status SMS 1 30 days adjustable Thanks of many Link Gate A Premium features you can satisfy very wide group of customers By setting of permitted numbers to memory of Link Gate A Premium you can restrict unrequested calls to public numbers As same as you can set Link Gate A Premium to pr2. Acknowledge character setting HERE 2 3 jn Type of dial tone n n 0 permanent tone n 1 dial tone up table of tone n 2 dial tone of public lines operator n 3 quiet 2 5 n Signalization to the call short tone each minute n 0 tone is turn off n 1 tone is turn on G n Restriction of call duration n 0 without restriction n 1 call duration restricted at 10 minutes T Reswen PT n 0 start without PIN n 1 start with PIN 2 n Outgoing DTMF Inband Outband AHONEN SER TT n 1 Outband DTMF PPI TT ee om romere sne me frequency is 5 sec Echo canceller 1 icient i Ge Number of dialled numeral after it is dial send immediately length of telephone number nn 00 function none active nn 01 19 number of numeral telephone number 3 7 n n n n Storingof PN PP PP 318 In Amplification of sound in outgoing direction 1t04 TTT 3 CLIR feature switching off outgoing CLIP 31 n 0 OFF n 1 ON xx 00 No charging pulses xx 12 12 kHz charging pulses xx 16 16 kHz charging pulses yy 00 1 pulse only at the moment of connection yy 01 to 99 seconds Pulses each 01 up to 99 seconds 7j2 n Amplification of sound in incoming direction 1to4 OU n 1 FSK CLIP Bell 7 4 In Call progress tone KERE EPIT ge tt et ON Roaming n 0 prohibited n 1 permitted 9j 9 Defauttseting PE TTT Table of tones Dial tone up setting Link Gate A Premium is ready to accept dial Bus
3. is When is used for PBX features you can change it on 24 An analogue phones are not enable send which is very used in GSM In this case is possible to use combination 00 to send it to mobile phone 31 This feature identificated connection of Link Gate A Premium to external line at some type of PBX ex Siemens Hicom 29 This feature is used for searching of antenna best position After feature activation you get tones immediately You end the feature by hang up 32 35 The GSM phones requested command to connection on inserted number The Link Gate A Premium will send a command immediately after acknowledge character dialling Notes Programming is only by tone dial DTMF Don t forget set even external line at PBX Changes are valid after hang up only finishing of programming mode It is very important especially in acknowledge character changes till hang up you must use previous acknowledgement After numbers dialling you must wait for confirming request insert acknowledge character and wait for confirming tone When you insert acknowledge character before wont be accepted 4 Switch to programming mode is possible even in busy tone 4 Some parameters are possible by software only Table of programming Dial Number Default 0 0 n n n n Password nnnn to programming mode access CCCs 1l1t n n n n Memory x for permitted fix number 1 to 4 digits 1 l2lnlnlnln wnn polarity n 0 OFF n 1 ON HH
4. card as same as all cables are connected do not forget that Link Gate A Premium is connected on external line not on extension connect device to main 230V The blue LED of power supply is light up within 10 sec After a while will flash a few times irregularly yellow LED GSM network registration Tle CPU then waiting for communication to GSM module via LED table communication off After 30 seconds the yellow LED start flashing up GSM signal strength via LED table When pick up connected analogue phone or call to Link Gate A Premium from PBX the LED of analogue line lights up green LED In the phone is hearing dial tone of Link Gate A Premium It is ready to use The most often problems during Link Gate A Premium compact installation gt All LED is not lighting There is a problem with the power supply Check connection to main 230V as same as connection of adapter to Link Gate A Premium gt The LED power supply lights When you make connection to Gate green LED is ON and in handset you hear busy tone Yellow LED flashing in period GSM module doesn t communicate with CPU During work with USB could be programmed fix communication rate for GSM module Use USB to program rate on autobauding gt The yellow LED flashing in period PIN unreadable After calling to Link Gate A Premium you get busy tone The SIM card requires PIN which is not pre programmed or is pre programmed wrongly gt The LED commu
5. nication to GSM is flash shortly one for 2 sec After calling to Link Gate A Premium you are hearing busy tone Link Gate A Premium is not log into GSM network bad signal gt The yellow LED communication to GSM is flashing up signal strength After calling to Link Gate A Premium is not light up green LED is not light up and in analogue phone is quiet It interrupted conduction of analogue line or so much big resistance in current loop for example longer cable between PBX and Link Gate A Premium gt The yellow LED communication to GSM is flashing up signal strength as same as green LED lights up The PBX hold pick up line of GSM Gate By incoming call you can remove this issue In other cases check PBX manual gt The Link Gate A Premium works but call is disturbed by interference Incorrect position of antenna against telephone line Change antenna position Note Default you make by parameter 99 in programming mode via programming table at page 11 All LEDs flashing as same as tone types are mentioned in tables at the end of manual You can purchase USB tool for PC configuration of the unit It is optional This tool is connected by a 6 wire cable to the units in middle of phone line See picture on page 2 You can control the GSM modul direcly by virtual COM port The Gate you can further uses ordinary GSM modem for data transmission internet connection or for SMS messages When unit is working as GSM modem
6. orts tones Confirm the feature by dialling acknowledgement Wait for confirming tone Follow programming tone again o0 606008080 8 Finish programming by hang up a phone Example programming of new permitted fix numbers 02 to memory 09 Dial acknowledgement default is In phone you are hearing waiting tone i BEE Dial password default 0000 Waiting tone is changing to programming tone HHE Dial 1902 Wait for tone of confirming request 3 shorts tones Confirm the feature by dialling acknowledgement Wait for confirming tone one long tone Finish programming mode by hang up a phone Warning After dialling of parameter value you have to wait for 3 short tones and then dial acknowledgement Wait for long tone confirms acceptation of this parameter Notes to each parameters 11 19 When you program some prefixes the Link Gate A Premium allows outgoing calls starts by those prefixes only The others will get busy tone When memories will be empty the calling won t be restricted default Memory of prefixes can content 1 digit only If you insert 1 digit only the Link Gate A Premium will check first position only Rewriting of memory by storing of new fix numbers are old fix numbers erased Erasing of memory Memory you will erase by storing of nothing You dial only number of memory which you want erase and confirm it 22 Very important features is acknowledge character setting Default
7. ovides incoming calls only INSTALLATION By pressing of yellow button release the SIM card holder Insert the SIM card and replace the SIM card holder Before inserting the SIM card we recommend checking at various mobile phone state of the SIM card logging with or without PIN PIN etc and set logging without PIN When you want logging with PIN you have to pre programmed this PIN and set logging with PIN via table of programming Without this setting the Gate wont work DO NOT FORGET ANTENNA CONNECTION The available place for installation select up following point of view 1 Distance from PBX possibility of GSM interferences to other PBX lines as same as length of line from Gate to PBX max 200m 2 Main 230 V for power supply of Gate 3 Quality of GSM signals at the installation place of GSM Gate Link Gate A Premium Power supply Quality of GSM signal The sound quality depends on BTS setting where you are connected by the Gate To find best place for antenna mounting you can use either mobile phone or feature 29 table of programming The suitable signal power is 3 scales of mobile graduation To check and find best position from GSM signal point of view you can use also GG SET configuration sw Connection of antenna MENU SETWhen you connect magnetic antenna keep on mounting at bigger iron subject This subject makes against weight at its depends the power of radiated signal When you inserted SIM
8. then is busy for voice connection When you pick up the line you will hear busy tone The unit is monitoring data transmission by modem The data transmission can not be permanent therefore the unit stays in data mode 10 seconds after finishing of data transmission Then is going back to Voice mode calling The same is when you are calling over unit It is busy for data transmission The optional sw supply to unit for sending and receiving SMS messages is SMS mail It is working under Outlook Outlook Express Opera etc And you can work with SMS as with normal e mails see manual for SMS mail It works in batches and allows programs communication interval 1 to 99 minutes to Link Gate A Premium for sending and receiving SMS Due this we avoid situation that unit is permanently blocked by data mode for voice communication Further functionality of USB is monitoring Link Gate A Premium operation It is possible a record even incoming call includes time and CLIP signal strength etc CONFIGURATION The programming mode is set after acknowledgement dialling to Link Gate A Premium In the analogue phone is waiting tone After password inserting is tone changing to programming tone Then you can programming each features of Link Gate A Premium via table of programming Progress of programming Dial 2 digits number of programming feature Dial 1 to 4 digits number for feature value programming Wait for a tone of confirming request 3 sh
9. tions Humidity Dimensions mm Weight Part of power supply Supply voltage Protection Safety group Analogue telephone line Telephone interface Telephone connector Impedance Dial Billing Start and end of connection Supply conduction Current loop Resistance of subscribers conduction Ringing Signalization CLIP GSM Mobile network Provider USB Link Gate A Premium various temperature 5 C 40 C 10 80 at 30 C 140 97 37 2159 8 12V AC DC adapter thermal fuse in adapter CSN EN 60950 group 2 2 wires RJ 11 600 Q 20 tone DTMF t gt 30 ms 12 16 kHz Polarity reversal symmetrical 24V max 29 mA max 500 Q 55 Ver 50 Hz 425 Hz 20Hz FSK Bell Quad band 850 900 1800 1900Mhz according SIM card 3V and 1 8 V version 1 1 virtual COM
10. y tone short tone repeated Called part is busy doesn t exist not permitted etc Ringing tone long tone and pause repeated Called part is ringing Waiting tone short tone repeated with quick cadence Link Gate A Premium waiting for password insert Programming short tone with quick cadence Programming mode of Link Gate A Premium Confirmation inquiry 3 short tones Inquiry to confirm inserted parameter Confirmation tone long tone Parameter was saved correctly Minute tone short tone with 1 minute period Minute beep to inform about GSM call Call progress tone short tones with different frequency Searching of called part LED signalling Permanent light lights up after 3 sec After power connection Power supply of unit Permanent light Line OFF HOOK Doesn t light Line ON HOOK Flashing in rythm of busy tone Programming or PC connection mode Flashing in rhytm of busy tone Initialization mode after power supply connection restart after programming etc 1 5 flashes with period 4 sec Stand by mode Number of flashes signal strenght Permanent light GSM connection is running call Short lights off with period 2 sec GSM modul doesn t communicate to CPU Flashing in period 2sec SIM is not readed Short flashes in period 2 sec Gate is not registrate to GSM network Technical parametres Type Operating position Operating condi
Download Pdf Manuals
Related Search