SP-PoE Splitter User Manual
Contents
1. 3 Connect proper DC plug from DC OUT of SP PoE to remote device Caution Please ensure the output voltage is correct for remote device Otherwise it will damage your remote device 4 Power on the remote device and the LED indicator on SP PoE will remains on SP PoE Splitter User Manual 9 Chapter 2 Hardware Installation Connect with other802 3af devices The SP PoE also provides an alternative way to connect to non IEEE 802 3af devices and to connect with an IEEE 802 3af in line power device like a Power over Ethernet Switch See the figure below Figure 4 PSE SP PoE application 100 meters EE eee 802 3af in ine power Switch Wireless Access Point 100Base TX UTP _ 100Base TX UTP with POE Power Line DO 10 SP PoE Splitter User Manual2. DIP Switch Output DC Connector Output Power Number of Device can be powered Ethernet Cable Installation Material Standards Conformance Standard Compliance 1x 10 100Base TX with IEEE 802 3af PoE PD for data DC in RJ 45 connector 1x 10 100Base TX for data out RJ 45 connector IEEE 802 3af Power over Ethernet PD 1 2 3 6 End Span or 4 5 7 8 Mid Span 48V DC Range 44 to 56VDV 10 100Mbps vary on Ethernet device attached 148810pps 64Bytes 5VDC 12VDC output voltage DC Jack 5 5 x 2 5 mm receptacle in the central post 12W max 1 TIA EIA 568 Category 5 5e cable Standalone or Wall mountable Plastic IEEE 802 3 10Base T Ethernet IEEE 802 3u 10 100Base TX Fast Ethernet IEEE 802 3af Power over Ethernet PD SP PoE Splitter User Manual Chapter 1 Overview Physical Specifications Dimensions W x D x H 2 87 x 2 17 x 0 94 73 x 55 x 24mm Weight 0 22 lbs 50g Environmental Specifications Operating Temperature 0 C 50 C Relative Humidity 5 90 non condensing Storage Temperature 20 C 70 C Relative Humidity 5 90 non condensing Electrical Specification Output Voltage DIP switch 5V 5VDC 2 0A max DIP switch 12V 12VDC 1 0A max NOTE This product is intended to be supplied by a UL Listed Direct Plug In Power Unit marked Class 2 or LPS and output rated 48 VDC 3 Amp minimum SP PoE Splitter User Manual 5 Chapter 1 Overvie
3. GE Security SP PoE Splitter User Manual Copyright 2010 GE Security Inc This document may not be copied in whole or in part or otherwise reproduced without prior written consent from GE Security Inc except where specifically permitted under US and international copyright law Disclaimer The information in this document is subject to change without notice GE Security Inc GE Security assumes no responsibility for inaccuracies or omissions and specifically disclaims any liabilities losses or risks personal or otherwise incurred as a consequence directly or indirectly of the use or application of any of the contents of this document For the latest documentation contact your local supplier or visit us online at www gesecurity com This publication may contain examples of screen captures and reports used in daily operations Examples may include fictitious names of individuals and companies Any similarity to names and addresses of actual businesses or persons is entirely coincidental Trademarks and GE and the GE monogram are trademarks of General Electric patents Company Other trade names used in this document may be trademarks or registered trademarks of the manufacturers or vendors of the respective products Intended use Use this product only for the purpose it was designed for refer to the data sheet and user documentation for details For the latest product information contact your local supplier or visit
4. nstraat 7 6003 DH Weert The Netherlands 2002 96 EC WEEE directive Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union For proper recycling return this product to your local supplier upon the purchase of equivalent new equipment or dispose of it at designated collection points For more information see www recyclethis info For contact information see our Web site www gesecurity com For contact information see our Web site www gesecurity eu SP PoE Splitter User Manual Content Chapter 1 Overview 1 Package Contents 2 Introduction 2 Product Overview 3 Chapter 2 Hardware Installation 7 Before Installation 7 Installation 9 SP PoE Splitter User Manual Chapter 1 Overview EEE 803 3af Po SP Pog R SPLIT ER ER ETHE The GE Security SP PoE is an IEEE 802 3af Power over Ethernet device that splits the 48VDC power input over an Ethernet cable into separate 5V and 12V DC power outputs SP PoE Splitter User Manual Chapter 1 Overview Package Contents Your SP PoE Splitter carton should contain the following items e The Power over Ethernet Splitter x 1 e User s Manual x 1 e 15cm UTP straight network cable x1 e DC Plug cable x 2 If any item is missing or damaged please consult the dealer from whom you purchased you SP PoE Splitter module Introduction The GE Security SP PoE is an IEEE 802 3af Power over Ethernet device that splits the 48VDC p
5. ower input over an Ethernet cable into separate 5V and 12V DC power outputs The SP PoE works with IEEE 802 3af power source equipment PSE This frees device deployment from restrictions due to power outlet locations and eliminate the costs for additional AC wiring and reduces the installation time When the PSE inserts DC Voltage into the CAT 5 cable it allows the cable between the PSE and SP PoE to transfer data and power simultaneously The maximum distance between the PSE and SP PoE is 100M Product Features e Complies with the IEEE 802 3z Gigabit Ethernet standard e 1X 1000Mbps fiber port e Plug and Play Installation e SFP1000SX 220 provides distance up to 220m over 62 5 125um fiber cable and 550m over 50 125um fiber cable 2 SP PoE Splitter User Manual Chapter 1 Overview e SFP1000LX 10Km provides distance up to 10km over 9 125um single mode fiber cable Product Overview Figure 1 shows the left and right side panels of the SP PoE Splitter Figure 1 Left and right side panels of the SP PoE a Ethernet DC y LED Indicators LED Color Function is Green Lights to indicate the port is providing 48VDC in line power SP PoE Splitter User Manual 3 Chapter 1 Overview Product Specifications Interface Ethernet DC Copper Port Ethernet Copper Port Power over Ethernet PoE Standard PoE Input Pin Assignment PoE Input Voltage Hardware Specification Data Rate Throughput Packet per second
6. us online at www gesecurity com This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures FCC compliance Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help SP PoE Splitter User Manual Regulatory information Manufacturer European Union directives Contact information CE Cu GE Security Inc HQ and regulatory responsibility GE Security Inc 8985 Town Center Parkway Bradenton FL 34202 USA EU authorized manufacturing representative GE Security B V Kelvi
7. w 6 SP PoE Splitter User Manual Chapter 2 Hardware Installation Before Installation If your network environment is very difficult to find a power socket for your AC DC Adapter of networked device the SP PoE provide DC power for this Ethernet Device conveniently and easily The SP PoE separates the power out and provides two kind of DC power output through its DIP switch and its voltage and current shown as below e 5VDC 2A e 12V DC 1A SP PoE Splitter User Manual Chapter 2 Hardware Installation Figure 2 5V 12V DC out DIP switch Ethernet DC OUT et The default value is set on 5V MS POE and SP PoE units can be installed in pairs However use of third party device is allowed if the device complied with IEEE 802 3af standard 8 SP PoE Splitter User Manual Chapter 2 Hardware Installation Installation To connect the hardware do the following 1 Connect a standard network cable from Ethernet DC of MS POE to Ethernet DC of SP PoE The POE LED of SP PoE MS POE will start to flash continuously Figure 3 MS PoE SP PoE application 100 meters Switch ur m E e i i CE Wireless Access Point Power 100Base TX UTP S 100Base TX UTP with PoE Power Line DC Note The SP PoE only accept IEEE 802 3af equipment other in line power device may cause the SP PoE malfunction 2 Connect the UTP cable in the package from Ethernet of SP PoE to the RJ 45 port of remote device
Download Pdf Manuals
Related Search