PACE SX-90 Unsoldering Handpiece User Manual
Contents
1. and turning it approximately ten 10 degrees to the right or left The door assembly can now be removed by simply gripping the door near the ear shaped protrusions and lifting straight up 2 Replace the disposable chamber by holding the door assembly in the palm of your hand with the filter assembly facing up With your free hand use a fresh solder chamber with the arrows facing away to push the spent chamber out of the door assembly and into a waste receptacle The fresh chamber is now in position and ready for reassembly CAUTION The handpiece will not function properly if the chamber is inserted incorrectly The directional arrows on the solder chamber must be pointed at the heater 3 Complete the process by lowering the door into the handle assembly Insure that the door is properly situated with the ears seated in their respective detents Now return the plunger assembly to its locked position by simply twisting the plunger locks mechanism so that it returns to the channels in the handle assembly 4 Insure that the door assembly is securely in place by attempting to lift the door from the handle assembly It should now be held firmly in place 5 Check all air hose fittings Actuate the vacuum and insure that proper vacuum is present at the tip 6 Return the handpiece to the cubby or resume work as required 2008 PACE Inc Southern Pines NC All Rights Reserved Page 8 of 11 www paceworldwide com PACE Sodr X Tractor H2. For thru hole desoldering select a tip with an I D just large enough to allow the lead to freely pass inside The tip O D should not exceed the diameter of the land to minimize risk of damage to the board substrate Tip Installation Before installing your desoldering tip Identify your Sodr X Tractor heater assembly Replacement SX 90 heater assemblies utilize part number 6010 0107 P1 SX 70 tips are NOT compatible with SX 80 or SX 90 handpieces SX 80 Endura tips will operate in SX 70 SX 80 and SX 90 handpieces SX 90 tips are only compatible with SX 90 handpieces SX 70 X 80 Sx 90 For optimal thermal transfer and performance always use SX 90 tips with SX 90 handpieces and heater assemblies 2008 PACE Inc Southern Pines NC All Rights Reserved Page 5 of 11 www paceworldwide com PACE Sodr X Tractor Handpiece For maximum productivity and proper fit install tips into your Sodr X Tractor when the heater is hot CAUTION During tip installation hold the handpiece with the heater pointed at an up ward angle to prevent injury 1 Insert the tip fully into the heater bore using the supplied tip tool P N 1100 0206 2 Gently tighten the Heater Set Screw 3 Recheck the Heater Set Screw periodically to insure that it remains snug NOTE Periodically clean the heater bore with a properly sized 3 16 O D wire brush P N 1127 0014 P5 t
3. set tip temperature 2 Using a moistened sponge remove all solder dross and flux residue from the tip 3 Using a large gauge flux cored wire solder tin the end of these tips Proper tinning enhances heat transfer to lands and extends tip life 4 During Flo desoldering or Thru hole desoldering on heavily fluxed or contaminated boards debris may collect inside the tip bore If this occurs clean the tip bore with the Sodr X Tractor Tip Cleaning Kit PACE part number 6993 0200 2008 PACE Inc Southern Pines NC All Rights Reserved Page 6 of 11 www paceworldwide com PACE Sodr X Tractor Handpiece 5 The Sodr X Tractor handpiece is now ready for use If not immediately using the handpiece store in its Tip amp Tool Stand NOTE Ensure that the tool stand sponge material is moist and free of debris Add water if necessary Wiping the heated tip on a dry sponge will only contaminate the tip and ultimately the board Through Hole Solder Extraction 1 Ensurethat the handpiece vacuum hose is connected to a VisiFilter and the Vacuum Port on the power source Select an operating temperature that will cause complete solder melt in 2 5 seconds somewhat longer on heavy multilayer boards A starting tip temperature of 316 C 600 F is recommended for most applications Position your index finger on the handpiece vacuum control switch Gently position the extractor tip over the lead contacting the solidified solder keeping tip perp
4. your local authorized PACE Distributor or PACE Incorporated to obtain the latest specifications The following are trademarks and or service marks of PACE Incorporated MD USA INSTACAL FUMEFLO HEATWISE PACEWORLDWIDE PERMAGROUND POWERPORT PONERMODULE TEMPWISE TIP BRITE AUTO OFF TEKLINK and INTELLIHEAT The following are registered trademarks and or service marks of PACE Incorporated Annapolis Junction Maryland U S A ARM EVAC FLO D SODR MINIWAVE PACE SENSATEMP SNAP VAC SODRTEK SODR X TRACTOR THERMOFLO THERMOJET THERMOTWEEZ VISIFILTER THERMO DRIVE and TOOLNET PACE products meet or exceed all applicable military and civilian EOS ESD temperature stability and other specifications including MIL STD 2000 ANSI JSTD 001 IPC7711 and IPC A 610 Additional copies of this manual or other PACE literature may be obtained from PACE www paceworldwide com PACE USA PACE Europe Limited 9030 Junction Drive 13 Tanners Drive Blakelands Annapolis Junction MD 20701 Milton Keynes USA MK145BU United Kingdom Tel 301 490 9860 Tel 44 01908 277666 Fax 301 498 3252 Fax 44 01908 277777 2008 PACE Inc Southern Pines NC All Rights Reserved Page 11 of 11 www paceworldwide com
5. PACE Operation and Maintenance Manual for the SX 90 amp SX 80 Sodr X Tractor Handpieces 5050 0492 Rev F Part Number Model Features 6010 0106 P1 SX 80 90 Black connector Handpiece Only 6010 0149 P1 SX 90 Blue Connector Handpiece Only 6993 0213 P1 SX 80 90 Black connector Handpiece amp Cubby 6993 0266 P1 SX 90 Blue Connector Handpiece amp Cubby PACE SX 90 Shown PACE Sodr X Tractor Handpiece TITLE PAGE msorelPeurel pee 3 Tip amp Tool Stand Setup caepit eodeni Eee ERR HR Ee 3E ER nana 4 Handpiece Setups coo de fedet e laore de a daa deua dae de ace eng 4 Vacuum Hose Connection sssssssssssssseseeeee eene nne e inen 4 Tip SelectlOri 2 5 iota cerea ce rige Ahlen ad ee Fade ate dele aa eed 5 Tip Installation ics iere peret Avice We cane eerie cite eee 5 Temperature Setting eisir iiien iii giad oiia i aiii nnns innen nennen 6 Burin ProCeQure nidu ini aai aar deron Pe Wis deu aaa adain iaaii aia Eiaa 6 Tip Preparation ectie iistiid aai ia Te ENE R NE E i 6 Through Hole Solder Extraction enne 7 Uer mE LEES 7 Special Applications ED 8 Replacing the Disposable Solder Collection Trap sseeeee 8 Heater Replacement atini isisisi diidiis ii i ed iiien intr ns en nnns 9 Corrective Maintenance dennin aaa aa raaa ae haas aAA a aha Taai de Lhaa AAAA entente 9 Handpiece Replacement Parts cc cccecsssceceeseeeeeeeseee
6. andpiece Heater Replacement The Sodr X Tractor utilizes a modular heater design which allows for a quick and easy change out of the heater assembly Remove and set aside any installed tip from the handpiece Disconnect the handpiece from the receptacle of the power source Remove the two heater assembly screws These screws can be accessed through the two holes found on the face of the heater shroud After the two heater assembly screws have been removed and set aside remove the heater assembly by pulling the heater module straight out Reassemble the handpiece in the following order Align the modular heater plug with receptacle on the handle assembly and gently push into place Replace and tighten the two heater assembly screws Insuring that the heater assembly is snugly in place when through Be careful not to over tighten the screws Connect the handpiece to the power source and return the handpiece to the cubby or resume work NOTE There are two heaters available for the SX80 90 handpieces If your handpiece came with a heater with a black plug in connector you must order and use heater part number 6010 0107 P1 if your handpiece came with a heater with a Blue plug in connector you must order and use heater part number 6010 0163 P1 A heater with the blue connector will NOT fit in to a handpiece fitted with the black connector Corrective Maintenance Your Sodr X Tractor requires no special maintenance other than bein
7. ctor Handpiece a Disconnect the 137cm 54 inch length of air hose from the FLOW IN side of the VisiFilter assembly Insert the ribbed end of a male quick connect hose mount fitting P N 1259 0087 into the free end of this air hose b Connectthe free end of a 1 inch 2 5cm length of air hose with an installed female quick connect hose mount fitting P N 1259 0086 to the FLOW IN side of the VisiFilter Assembly c The 137cm 54 inch length of air hose can now be easily moved between the VisiFilter Assembly and the Controllable Pressure Port The VisiFilter assembly remains connected to the Vacuum Port 4 Additional fittings may also be added to the hose connection at the rear of each air handpiece to ease changing of handpieces NOTE When removing any air hose turn and pull Do not attempt to pull hose directly off Damage to or breakage of fitting or VisiFilter may occur Use your Sodr X Tractor with a clean VisiFilter element Otherwise deterioration in performance or damage to the unit may occur Tip Selection PACE Endura Tips come in three basic types 1 Desoldering Tips These tips are tinnable and provide enhanced thermal performance for thru hole desoldering on high mass boards 2 Precision These tip feature smaller ID sizes with larger mass for improved thermal recovery 3 Flo D Sodr Tips These tips provide rapid continuous extraction of old or excess solder from SMT lands Size selection of tips is important
8. ed the component is easily removed If any solder should remain in the plated thru hole after extraction resolder the connection and perform this procedure again Tip Cleaning During heavy continuous desoldering on boards with flux residues or other contamination the tip may occasionally become clogged with such material If this should occur clean the tip with the Tip Cleaning Kit PACE part number 6993 0200 by inserting the wire tool into the tip end 2008 PACE Inc Southern Pines NC All Rights Reserved Page 7 of 11 www paceworldwide com PACE Sodr X Tractor Handpiece Special Applications If you require assistance in the use of this handpiece or with a special application contact PACE Technical Support at Telephone 301 490 9860 Fax 301 490 0193 Replacing the Disposable Solder Collection Trap As the Sodr X Tractor is used solder and flux build up will begin to impede the airflow and decrease system performance The SX 90 amp SX 80 utilize a disposable chamber that makes maintenance a quick and simple process Regular replacement of the Sodr Flux Trap will keep the Sodr X Tractor handpiece operating at peak performance To replace the Sodr Flux Trap follow the procedures outlined below 1 While holding the Sodr X Tractor with the tip facing away from you and the handpiece in a downward position remove the door assembly from the handpiece This action is accomplished by pulling the plunger lock approximately 14
9. eeeeneneeeeeneneeseeneneeeeeeneneeeeesenees 10 iJ E e RTE E EEE EAE A EE EIE IE E E EEA EA EEEE 10 Goritact InfOrmallOni s enano texere rta ee era RR CREAR AEEA EE AEAEE RENSA EE MAL XN ENERO eura od 11 2008 PACE Inc Southern Pines NC All Rights Reserved Page 2 of 11 www paceworldwide com PACE Sodr X Tractor Handpiece These instructions detail the basic operational guidelines for using the SX 80 amp SX 90 Sodr X Tractor handpieces The SX 80 has yellow coloration on it and the SX 90 has blue coloration on it The SX 80 is only available in SensaTemp technology while the SX 90 is available in SensaTemp and Intelliheat technologies Introduction The Sodr X Tractor handpiece provides thermally enhanced through hole desoldering on extra heavy multilayer assemblies at safer lower temperatures even during continuous use This Sodr X Tractor handpiece features a large easy to replace solder trap slim ine pencil grip design and finger actuated vacuum switch facilitates ease of use and manipulation in tight places The Sodr X Tractor is a member of the PACE SensaTemp family of advanced handpieces CAUTION Always return heated handpieces to the appropriate Tip amp Tool Stand when not in use Failure to do so may cause burns to the operator equipment or work surfaces and may be a potential ignition source if combustible materials are nearby Always use this handpiece in a well ventilated area to avoid inhalation of fumes created by so
10. endicular to the pad and board Do not apply pressure against the pad at any time during this operation Damage to the board may result 4 Gently move the lead ev a Inacircular motion for round leads b In a back and forth motion for flat leads until the lead moves freely Free lead movement indicates that complete solder melt has been obtained 5 While continuing to move lead actuate vacuum with the finger switch and keep on for at least 2 seconds to cool joint and prevent re sweating The length of time from when heat is applied until the time vacuum is started i e complete solder melt should be 2 5 seconds under normal conditions Heavy multilayer boards may require somewhat longer heating times In extreme cases preheating or auxiliary heating is recommended to achieve the safest results NOTE Early activation of the vacuum may result in incomplete removal of solder from the joint being desoldered Free movement of the lead is the work piece indicator that proper solder melt has been achieved In the event that all the solder has not been removed from the hole resolder the hole and try again after the board has been allowed to cool 6 Remove tip from pad and continue vacuum application for an additional 2 seconds to insure that all residual solder is drawn into the solder collection chamber 7 Rectin tip using large gauge flux cored solder and return Sodr X Tractor to its Tool Stand 8 After all leads are desolder
11. g kept clean The heater bore and the heater assembly set screw which secures the tip must be kept free of oxidation and debris in order to maintain the proper tip to ground resistance 2008 PACE Inc Southern Pines NC All Rights Reserved Page 9 of 11 www paceworldwide com PACE Sodr X Tractor Handpiece Handpiece Replacement Parts Soar X Tractor Exploded Diagram SX 90 Replacement Part Numbers Ref Description Part Number 1 Solder Flux Chamber 1309 0054 P10 Handle Assembly Black Connector 6010 0115 P1 2 Handle Assembly Blue Connector 6010 0162 P1 3 Door Assembly 1119 0141 P1 Heater Assembly Black Connector 6010 0107 P1 4 Heater Assembly Blue Connector 6010 0163 P1 5 Plunger Shaft 1261 0154 P1 6 Plunger Lock 1500 0063 P1 7 Front Seal 1213 0087 P1 8 Rear Seal 1213 0086 P1 9 C Clips 1348 0387 P3 10 Spring Long Slide 1221 0136 P1 11 Spring Short Slide 1221 0137 P1 12 Door Lock 1119 0142 P1 NOT PICTURED 13 Heater Set Screws Pack of 10 1348 0547 P10 14 Glass Flux Trap Kit 6000 0212 P1 15 Glass Chamber Only 1265 0011 P1 Service Please contact PACE or your local distributor for service and repair 2008 PACE Inc Southern Pines NC All Rights Reserved Page 10 of 11 www paceworldwide com PACE Sodr X Tractor Handpiece PACE Incorporated retains the right to make changes to specifications contained herein at any time without notice Contact
12. lder flux NOTE Always use your Sodr X Tractor with a clean VisiFilter element Otherwise deterioration in performance or damage to the unit may occur Select and enter your desired true operating temperature on your PACE power source To save tip life and reduce the possibility of damage PACE recommends using the lowest possible tip temperature that will provide rapid yet controllable melt of the entire solder joint to be extracted Begin with an operating temperature in the range of 316 C 600 F and adjust as necessary 2008 PACE Inc Southern Pines NC All Rights Reserved Page 3 of 11 www paceworldwide com PACE Sodr X Tractor Handpiece Handpiece Setup Connect the handpiece connector plug into one of the Power Receptacles on your PACE power source in the following manner 1 Align guide on connector with slot on power receptacle 2 Insert connector into power receptacle 3 Tum the connector housing clockwise to lock in place Vacuum Hose Connection To set up your Sodr X Tractor vacuum hose connection perform the following steps 1 Vacuum Hose To Handpiece Connection a Attach one end of a 137cm 54 inch length of air hose to the metal tube in the back of the handpiece b If you have a PACE system incorporating only one handpiece attach the air hose to the SX handpiece power cable using the supplied Hose Clamps Space them evenly along the length of the power cable starting at a point 6 inches from the ends of
13. o insure optimum heat transfer and proper tip grounding Temperature Setting To save tip life and reduce the possibility of damage to the PCB PACE recommends using the lowest possible tip temperature that will provide rapid yet controllable melt of the entire solder joint Begin with an operating temperature of 316 C 600 F and adjust as necessary Tip temperatures in excess of 399 C 750 F may cause damage For safest removal some components on extra heavy assemblies may require preheating or auxiliary heating Burn In Procedure The following Burn In procedure must be performed to insure optimum performance and life of this product Insure that system is located in a well ventilated area on Initial power up Remove plastic cap from end of Heater Assembly If present Connect Handpiece to PACE system Power Source Fon Set Handpiece Tip temperature to 316 C 600 F Burn Handpiece in for 10 minutes at this temperature 5 Set Handpiece Tip Temperature to 427 800 F Heater Assembly will again emit smoke Burn Handpiece in at this temperature until emission of smoke ceases Approximately 15 minutes 6 Operate Handpiece in a normal manner Tip Preparation Proper tip preparation will insure optimum results and increase tip life Follow this procedure before each component removal or land preparation operation and prior to storage of the handpiece in its Tip amp Tool Stand 1 Ensure that the installed tip is at
14. the handpiece c Ifyou have a PACE system incorporating 2 or more air handpieces e g SX 90 80 TP 100 TJ 70 TP 65 you may wish to leave the air hose assembly unattached to allow a quick change to any air handpiece being used NOTE Insure that only one air handpiece is connected to either the Vacuum Port or Controllable PRESSURE Port at one time Attachment to both ports simultaneously will cause a deterioration of performance 2 Prepare a VisiFilter in the following manner a Connecta 1 inch 2 5cm length of clear PVC air hose to the FLOW OUT side of the VisiFilter push and turn the hose onto the VisiFilter nipple to seat b Insertthe ribbed end of a male quick connect hose mount fitting P N 1259 0087 into the free end of the 1 inch 2 5cm length of air hose connected to the FLOW OUT side of the VisiFilter c Connect the free end of the 137cm 54 inch length of air hose to the FLOW IN side of the VisiFilter d Insert the end of the quick connect hose mount fitting on VisiFilter FLOW OUT side into the power source Vacuum Port 3 When using air pressure and or utilizing multiple air handpieces PACE recommends the use of the following set up procedure which utilizes additional quick connect hose mount fittings An assortment of quick connect air fittings are supplied with each additional air handpiece 2008 PACE Inc Southern Pines NC All Rights Reserved Page 4 of 11 www paceworldwide com PACE Sodr X Tra
Download Pdf Manuals
Related Search