MS4CT+ Quick Installation Guide
Contents
1. ANS IGITAL Follow all instructions Do not place this device near water and clean only with dry cloth Do not block any ventilation openings Install in accordance with Sans Digital s instructions Do not place near any heat sources such as radiators heat registers stoves or the devices including amplifiers that produce heat Protect the power cord from being walked on or pinched particularly at plugs convenience receptacles and the point where they exit from the apparatus Hard Drive Installation 1 Use the enclosed handles to secure the 4 HDDs with screws in the given direction indicators 2 Push the tab on the front cover downward to open the cover ANS IGITAL 3 Press down the tab located on the top of the metal frame to remove the frame MOBILESTOR MS4UT B MS4CT Only use attachments accessories specified by Sans Digital Unplug this during lightning storms or when unused for long periods of time Refer all servicing to Sans Digital Technical Support Servicing is required when the devices has been damaged in any way such as power supply cord or plug is damaged liquid has been spilled or objects have fallen into the devices Carefully read and follow the Quick Installation Guide and User Manual Do not drop or shake the device Do not move the device when it is powered on Do not overload wall outlets 4 Take the paper drive bay holder out of2. BIG 7 RAID 0 Striping mode 8 RAID Mirroring mode 9 RAID 3 10 RAID 5 11 RAID 10 12 Rebuild 13 eSATA In use access 14 Firewire In use access MS4CT only 15 Smart fan automatic mode 16 Smart fan manual mode 17 Fan speed Level 18 Fan speed Level 2 19 Fan speed Level 3 20 HDD error When any of HDD HDD4 has error HDD error is on 21 24 HDD HDD2 HDD3 HDD4 Blue Active Purple Access Red Rebuild 4 HDD HANDLE g_ coco p 5 METAL FRAME o o n m m 1394b Port MS4CT Power Connector EB RAID Setup For RAID setup press and HOLD the MODE button for 3 seconds until the LED flashes Press the button again to change the RAID mode The default setting is RAID 5 2 After selecting the desired RAID mode press and HOLD the confirmation button located behind a small cover on the back panel until the device powers off NOTE When using RAID function HDDs with the same brand model and capacity is strongly recommended 3 The selected RAID set will be ready to use Please format the disk follwing the OS instructions A Please refer to manufacture website for a list of certified HDDs B Rebuild time varies depending on the HDD volume about hour for 200GB Once Rebuild is complete the rebuild LED will turn off 1 Operating Environment Temperature 0 50 Celsius Humidity 0 90 2 USB p
3. the device 5 Slide 4 HDDs into the chassis and make sure they are securely installed in the order from top to bottom Make sure the HDDI is securely installed first at all times Otherwise the PC may not recognize the device 6 Reinstall the metal frame that was removed in Step 3 Make sure the bottom of the frame is locked inside the track before closing the cover 7 Connect the power supply to the device plug in USB or eSATA cable in the rear panel and power on the device 8 Setup RAID settings by following RAID Setup instructions 9 Please format the HDD via OS if the HDD is unformatted Refer to OS manual for detailed instructions on how to format HDD 10 To take the HDD out from the device slightly press down the handle and pull it out OL_JOoooL jo Diagrams 1 FRONT PANEL ANS IGITAL 3 RIGHT SIDE PANEL RAID Config 1394a Port MS4CT USB 3 0 Port eSATA Port 1 Blue Power on Orange Sleep 2 USB In use access 3 Power button It needs to be pressed and held for 3 secs to power off This design prevents accidental power off 4 Mode RAID mode button needs to be pressed and held for 3 secs to switch the device RAID mode Confirmation button is located at on the back of the unit This design will prevent accidental execution of this function 5 Fan button Controls auto amp manual modes and fan speed from level to level 3 6 RAID 0 Spanning mode
4. ort of your PC must support power off function so that the device would go to sleeping mode Setting up motherboard s power management in S3 is strongly recommended For more details please refer to user guide of motherboard BIOS setting 3 Smart fan is controlled by the built in thermal sensor and it comes with 2 modes auto manual and 3 levels of speed Level l higher than 55 C 2 500rpm 3 500rpm Level 2 45 C 54 C 1 800rpm 2 500rpm Level 3 below 45 C 1 200rpm 1 800rpm 4 Press the power button to power on the device or press the button for 3 seconds to power off the device
Download Pdf Manuals
Related Search