"user manual"
Contents
1. RGBW DMX protocol Version 1 1 Mode 1 Standard 16 bit Mode 2 Reduced 8 bit Type of control Special functions Reserved To activate following functions stop in DMX value for at least 3 sec and shutter must be closed at least 3 sec Shutter channel 14 9 must be at range of 0 31 DMX Corresponding menu items are temporily overrided 30 39 RGBW colour mixing mode 40 49 CMY colour mixing mode 50 59 Colour calibration mode On 60 69 Colour calibration mode Off 70 89 Reserved 90 99 Dimmer curve linear 100 109 Dimmer curve square law 110 179 Reserved To activate zoom reset function stop in DMX value for at least 3 sec 180 189 Zoom reset 190 255 Reserved Red Cyan coarse 0 255 Red LEDs saturation control 0 100 proportional Red Cyan fine 0 255 Red LEDs saturation fine control min gt max proportional 3 Green Magenta coarse 0 255 Green LEDs saturation control 0 100 proportional 5 Green Magenta fine 0 255 Green LEDs saturation fine control min gt max proportional Blue Yellow coarse 0 255 Blue LEDs saturation control 0 100 proportional 7 Blue Yellow fine 0 255 Blue LEDs saturation fine control min gt max proportional White coarse RGBW mode only 0 255 White LEDs saturation control 0 100 proportional White fine RGBW mode only 0 255 White LEDs saturation fine control min gt max proportional CTO 10 0 No function step 1 255 Colour temperature correction proportional Virtual2. all pixels W LA white LEDs all pixels CTO a colour temperature correction Vir C a virtual colour Zoom azoom movement Stro astrobe shutter Dimm a dimmer S Tm a step time 0 25 5 sec COPY copying the current prog step to the next prog step 4 Press ENTER button to confirm adjusted value 5 Press ESCAPE button select next prog step press ENTER button and repeat steps 3 5 6 7 Reset This option resets zoom system of the fixture 6 8 Special functions Special RDM UID RDM L This menu item shows the first part of the RDM identification code 15 ArcPad Zoom 48MC RDM H This menu item shows the second part of the RDM identification code Wireless Wireless DMX status The menu serves for reading of the wireless operation status Stat Wireless DMX information The menu item shows level of received signal in UnLink Wireless DMX unlink The item serves for unlinking the fixture from transmitter Adiust Adjustment The menu allows the fine adjustment of colours DMX Val DMX values Use the menu to set DMX values of fixture s channels Calib A calibration of white colour 5600K Load d C Loading a default calibration Sw Upd Software update The menu item allows you to update software in the fixture via either serial or USB port of PC The following are required in order to update software PC running Windows 95 98 2000 XP 7 8 or Linux DMX Software Uploader Flash cable R
3. alone mode after switching the fixture on Selected program will be played continuously in a loop Off The option disables Auto Run function Test The option will start built in test program User The option will start user created program Pr Play Playing program Select this menu to run a user created program in a loop Test Prg The option runs built in test program User Prg The option runs user created program Select the program you wish and press ENTER The selected program starts running By Pressing ENTER again program pauses running Pr Edit Editing program Select this menu to edit or create the program The ArcPad Zoom 48MC has one built in program and one user editable program up to 40 steps Each program step has a step time during which effects last in the current step To edit program Procedure 1 Press UP or DOWN to select the menu Pr Edit and press ENTER 2 Press UP or DOWN to select the desired program step and press ENTER button 3 Press UP or DOWN to select the desired item and press ENTER button Now you can edit by UP or DOWN buttons the DMX value 0 255 for selected item Prg End a total number of the program steps value 1 40 This value you should be set before starting of programming e g if you want to create program with the 10 steps set Prg End 10 Powr a power special functions R LA red LEDs all pixels G LA green LEDs all pixels BLA blue LEDs
4. colour wheel 11 7 No function step ArcPad Zoom 48MC White 2700 K step White 2700 K tungsten emulation step White 3200 K step White 3200 K tungsten emulation step 7 9 White 4200 K step 10 12 White 5600 K step 13 15 White 8000 K step 16 Blue Blue full Red Green White 0 step 17 55 Red 0 Green gt up Blue full White 0 proportional 56 Light Blue Red 0 Green full Blue full white 0 step 57 95 Red 0 Green full Blue down White 0 proportional 96 Green Red 0 Green full Blue 0 White 0 step 97 134 Red5up Green full Blue 0 White 0 proportional 135 Yellow Red full Green full Blue 0 White 0 step 136 174 Red full Green gt down Blue 0 White 0 proportional 175 Red Red full Green 0 Blue 0 White 0 step 176 214 Red full Green 0 Blue up White 0 proportional 215 Magenta Red full Green 0 Blue full White 0 step 216 246 Red gt down Green 0 Blue full White 0 proportional 247 Blue Red 0 Green 0 Blue full White 0 step 248 251 Rainbow effect with fade time from min gt max speed proportional 252 255 Rainbow effect without fade time from min gt max speed proportional Zoom coarse 0 255 Zoom from min to max beam angle proportional Zoom fine 0 255 Fine zooming from min gt max proportional Shutter Strobe 0 31 Shutter closed step 32 63 Shutter open step 64 95 Strobe effect from slow to fast proportional 96 127 Shutter open step 128 143 Opening pulses i
5. or installing the fuses or any part Do not overload supply line as this can result in fire or electric shock Make sure that the power data cable is never crimped or damaged by sharp edges Check the fixture and the power data cable from time to time Do not install the unit near naked flames Refer servicing to qualified service personnel This fixture falls under protection class Therefore this fixture has to be connected to a mains socket outlet with a protective earthing connection Do not connect this fixture to a dimmer pack Warning Risk Group 2 LED product according to EN 62471 LED light emission Risk of eye injury Do not look straight at the fixture s LEDs during operation The intense light beam may damage your eyes Keep compustible materials at least 0 2 m away from the fixture If the fixture has been exposed to drastic temperature fluctuation e g after transportation do not switch it on immediately The arising condensation water might damage your device Leave the device switched off until it has reached room temperature Avoid brute force when installing or operating the fixture ArcPad Zoom 48MC When choosing the installation spot please make sure that the fixture is not exposed to extreme heat or dust Avoid using the unit in locations subject to possible impacts Only operate the fixture after having checked that the housing is firmly closed and all screws are tightly fastened Make sure that
6. the area below the installation place is blocked when rigging derigging or servicing the fixture Do not block the front glass cover with any object when the fixture is under operation The fixture body never must be covered with cloth or other materials The fixture becomes very hot during operation Allow the fixture to cool approximately 30 minutes prior to manipulate with it Operate the fixture only after having familiarized with its functions Do not permit operation by persons not qualified for operating the fixture Most damages are the result of unprofessional operation Do not attempt to dismantle or modify the unit Please consider that unauthorized modifications on the fixture are forbidden due to safety reasons Please use the original packaging if the fixture is to be transported If this device will be operated in any way different to the one described in this manual the product may suffer damages and the guarantee becomes void Furthermore any other operation may lead to dangers like short circuit burns electric shock etc ArcPad Zoom 48MC 2 Fixture exterior view 3 3 1 Head 2 LED zone 4 3 Tilt locks Ts 4 Bracket 5 Control board with cover 6 Power DMX input 3 Installation 3 1 Mounting the fixture The ArcPad Zoom 48MC can be arranged in any position orientation without altering its operation characteristics The LED module can be tilted to desired position by means of the t
7. ANOLIS a ArcPad Zoom 48MC ArcPad Zoom 48MC W USER MANUAL ArcPad Zoom 48MC Table of contents 1 Safety a din un de en er dde nt da a D Da SUR dE D led au da na COVER Aa Ra 3 2 Fixture exterior VIEW rt meras tien hae nt hen ee le te ne 5 Stalin dad diel pelado oa ta Siad 5 3 1 Mountingthe fixture lt da a Nada De don CG RNA dr att 5 3 2 Connection to the Mains ii AA A Ne en etd 6 3 3 Wireless DMX operationens sra ca is iii 7 4 ArcPad Zoom 48MC RGBW DMX protocol ccccccssccecssssececsssececssssececsesaececeeseseeecsesaececseaaesecsesaeeeeesaeeeesesaeeeeseaaes 8 5 Control menu map RGBW version cccscccecssssececssssececsesseecssssececsesaececsesseceseeesaececseasececsesaececesseeeeseaaeeecsesaeeeeesaaas 10 ICONO Men ssa nora cen ceets rasas aani a t men e eme ia LER nt aten nb nada nata Serato 13 6 1 Addressing DMXA iii aeee nana rece na arrasa EPAI nana asse ALADO IA PEII ESSA 13 6 2 Fixtureiintormation INTO es A A A AAA AA AAA 13 A O de et de vd nas dote rat 14 6 4M n al Control Manli mn end RM ses sh sual Mari ner Met en ein nes 14 6 5 Test program TeSt PEE loa ini ia Ad E Ea It ia bata titine 14 6 6 Stand alone SEA ONE ii A a A one A AA tha 15 RO tess SRU do vance iden von cities Ue anni nn ide ere nan shee vba colis ee ne te Een 15 6 8 Special functions Special e ccc ecsesccseessececeesececeeseecsesaeeeceesseeececsaeeececsseeecsesseeececsseeescaaeeeceesaeeeseesae
8. MX RDM module only for ArcPad Zoom 48MC W e Compliance with USITT DMX 512 1986 amp 1990 and 512 A e Full DMX fidelity and frame integrity e Auto sensing of DMX frame rate and frame size e lt 5ms DMX latency e Operational frequency range of 2402 2480 MHz e Producer LumenRadio Strobe e Strobe effect with variable speed max 20 flashes per second e Pre programmed random strobe pulse effects Dimmer e Smooth 16 bit dimming from O 100 Connection e Data power cable Li9Y11Y 3xAWG16 2xAVG24 shielded and jacketed e junction box Mounting e Via mounting bracket Protection factor e IP 67 CE e Suitable for wet locations ETL Impact resistance e IK 10 18 ArcPad Zoom 48MC Temperatures e Ambient temperature range 20 C 40 C e Maximum housing temperature 70 C Total heat dissipation e 440 BTU h calculated Weight e 11 6 kg fixture e 1 5 kg floor stand Dimensions mm A IL da JAM jjj UML al hy SECTION A A 19 ArcPad Zoom 48MC Junction box I oT a2 113 S amp S _ A E Ll I a e Included items e 1x ArcPad Zoom 48MC e 1 x Junction box P N9971 4886 e 1 x Data power cable e 1 x User manual Optional accessories e Floor s
9. S232 DMX No 13050624 if you want to use a serial port of PC Robe Universal Interface if you want to use an USB port of PC Note 1 Software update should execute a qualified person If you lack qualification do not attempt the update yourself and ask for help your Anolis distributor Note 2 DMX address user program and all items in the menu Pers will be set to their default factory values To update software in the fixture Installation of the DMX Software Uploader 1 DMX Software Uploader program is available from the Anolis web site at WWW anolis cz 2 Make a new folder e g Anolis Uploader on your hard disk and download the software to it 3 Unpack the program to the folder l Fixture software updating 1 Determine which of your ports is available on your PC and connect it with the DMX input of the fixture if you using the flash cable RS232 DMX with the DMX output of the Robe Universal Interface if you using the USB cable Disconnect the fixture from the other fixtures in a DMX chain Turn both the computer and the fixture on Make sure the lamp is switched off only if the fixture involves a lamp 2 Switch the fixture to the updating mode by selecting the SW Upd item and press ENTER Note If you do not want to continue in software update you have to switch off and on the fixture to escape from this menu We recommend to cancel all running programs before starting the Software Uploader 3 Run the Software Uplo
10. ader program Select desired COM and then click on the Connect button Select COM if the serial port is used or Robe Universal Interface if the USB port is used If the connection is OK click on the Start Uploading button to start uploading It will take several minutes to perform software update If the option Incremental Update is not checked all processors will be updated including processors with the same software version If you wish to update only later versions of processors check the Incremental Update box Avoid interrupting the process Update status is being displayed in the Info Box window When the update is finished the line with the text The fixture is successfully updated will appear in this window and the fixture will reset with the new software Note In the case of an interruption of the upload process e g power cut the fixture keeps the updating mode and you have to repeat the software update again 16 ArcPad Zoom 48MC 7 RDM This fixture is ready for RDM operation RDM Remote Device Management is a bi directional communications protocol for use in DMX512 control systems it is the new open standard for DMX512 device configuration and status monitoring The RDM protocol allows data packets to be inserted into a DMX512 data stream without adversely affecting existing non RDM equipment By using a special Start Code and by complying with the timing specifications for DMX512 the RDM protocol
11. allows a console or dedicated RDM controller to send commands to and receive messages from specific moving lights RDM allows explicit commands to be sent to a device and responses to be received from it The list of commands for the fixture is the following Parameter ID DISC_UNIQUE_BRANCH DISC_MUTE DISC_UN_MUTE DEVICE_INFO SUPPORTED_PARAMETERS SOFTWARE_VERSION_LABEL DMX_START_ADDRESS IDENTIFY_DEVICE DEVICE_MODEL_DESCRIPTION MANUFACTURER_LABEL DEVICE_LABEL SENSOR_DEFINITION SENSOR_VALUE DISPLAY_LEVEL DEVICE_RESET DMX_PERSONALITY DMX_PERSONALITY_DESCRIPTION STATUS_MESSAGES STATUS ID DESCRIPTION DEVICE HOURS Please see the Robe Universal Interface user manual for detail description of RDM operation 17 ArcPad Zoom 48MC 8 Technical specifications Power supply e Electronic auto ranging e Input voltage 100 277V AC 50 60 Hz e Max power consumption 150W 0230V power factor 0 94 Optic 8 Effects e Light source 12 x 15W LED multi chip e Zoom range 8 44 at beamu e RGBW or CMY colour mixing e Built in colour macros e Adjustable strobe sequences eTypical Lumen maintenance 70 60 000 hours Control e Setting amp Addressing two row LCD display 4 control buttons e Control USITT DMX 512 RDM support e DMX protocol modes 2 16 10 control channels e Operations modes DMX Stand alone e Manual control of all effects via control panel e One editable program up to 40 steps Wireless D
12. eesesaaaeeesees 15 WARD Vs A CER E Us Orada A A AA antec tate A A Miedo teh O 17 8 Technical specifications 18 Cd O ao 21 9 1 Replacing a TUS 232808 anale Le Pr hat ere annee d inde oli dee ni e iaae e nan a nie eg 21 ArcPad Zoom 48MC FOR YOUR OWN SAFETY PLEASE READ THIS USER MANUAL CAREFULLY BEFORE POWERING OR INSTALLING YOUR ArcPad Zoom 48MC Save it for future reference This device has left our premises in absolutely perfect condition In order to maintain this condition and to ensure a safe operation it is absolutely necessary for the user to follow the safety instructions and warning notes written in this manual The manufacturer will not accept liability for any resulting damages caused by the non observance of this manual or any unauthorized modification to the device Please consider that damages caused by manual modifications to the device are not subject to warranty This device is for professional use only It is not for household use 1 Safety instructions DANGEROUS VOLTAGE CONSTITUTING A RISK OF ELECTRIC SHOCK IS PRESENT WITHIN THIS UNIT Make sure that the available voltage is not higher than stated on the rear side of the fixture This fixture should be operated only from the type of power source indicated on the marking label If you are not sure of the type of power supplied consult your authorized distributor or local power company Always disconnect the fixture from AC power before cleaning removing
13. emperature in the moving LED head Current A current temperature of the moving LED head Highest A maximum temperature of the moving LED head since the fixture has been fabricated High Res A maximum temperature of the the moving LED head since the counter was last reset 13 ArcPad Zoom 48MC In order to reset this counter press and hold both UP and DOWN buttons and the Enter button at the same time Sw Ver Software versions Select this item to read version of software in fixture processors IC 1 IC 2 IC 3 WL 6 3 Personality Pers DMX Pres DMX preset Use the menu to select desired channel mode Mode 1 16 control channels Mode 2 10 control channels RGB Cnt RGB counting If this function is active the white channel channel 4 uses red green and blue chanels in proportional relation to ensure max light output in a white colour if white channel full also red green and blue channels are full DMX In DMX input Use the menu to select mode of receiving DMX signal Wired DMX signal is received by means of the standard DMX cable Wireless DMX signal is received by means of the inbuilt wireless module if the module is installed Display Display adjusting This menu allows you to adjust the display behaviour Turn This function rotates menu 180 degrees from current orientation On Off T This function allows you to keep the display permanent on or turn it off two minutes after last p
14. ers menu confirms adjusted values and leaves menu A UP and Y DOWN buttons move between menu items on the same level sets values After switching the fixture on display shows current DMX address 6 1 Addressing DMXA Set DMX address Use this menu item to set the DMX start address of the fixture which is defined as the first channel from which the fixture will respond to the DMX controller Please be sure that you do not have any overlapping channels in order to control each ArcPad Zoom 48MC correctly and independently from any other fixture on the DMX data link If there is no data received at the DMX input the display will start to flash 0001 with actually stored DMX address DMX Pres DMX preset Use the menu to select desired channel mode Mode 1 16 control channels Mode 2 10 control channels 6 2 Fixture information Info POn Time Power on time Select this menu to read the number of fixture operation hours Total The item shows the total number of the operation hours since the ArcPad Zoom 48MC has been fabricated Reset The item shows the number of the operation hours that the ArcPad Zoom 48MC has been powered on since the counter was last reset In order to reset this counter to O press and hold both UP and DOWN buttons and the Enter button at the same time DMX In DMX readout The menu is used to read DMX values of each channel received by the fixture Temp Temperature The menu shows t
15. ilt lock Use an Allen key 6 to adjust desired tilt position Three slots in the mounting bracket serve for mounting on the non flammable flat surface 6 Dimensions in mm ArcPad Zoom 48MC Ensure that the structure to which you are attaching the fixture is secure Caution Overhead installation requires experience Fixtures may cause severe injuries when crashing down If you have doubts concerning the safety of a possible installation do not install the device and consult installation with an expert 3 2 Connection to the mains Fixtures must be installed by a qualified electrician in accordance with all national and local electrical and construction codes and regulations This device falls under class one and must be grounded The ArcPad Zoom 48 MC is equiped with with a 5 cored power data cable The 3 cores serve for the power supply and next 2 shielded cores are intended for DMX connection as shown the table se a DE EOI CI ET The power data cable is connected to ajunction box as shown on the picture below la 6 x mini blocks spring connection 0 F ABB DS2 5 10 4L Terminal plate ZAG6 Terminal box Power connection Terminal box DMX connection Connect the junction box acording to the tables below Power connection Green yellow ArcPad Z
16. n sequences slow gt fast proportional 144 159 Closing pulses in sequences fast gt slow proportional 160 191 Shutter open step 192 223 Random strobe effects from slow to fast proportional 224 255 Shutter open step 15 10 Dimmer coarse 0 255 Dimmer intensity from 0 to 100 proportional 16 Dimmer fine 0 255 Dimmer intensity from min gt max proportional Halogen lamp effect during dimming ArcPad Zoom 48MC 5 Control menu map RGBW version Default settings Bold print Set DMX 001 255 address DMX Pres RE C DE A CEI A EE ES Join fe D A A A RE HS DD CS RE ES O pee ee A ES IR E E JA e PS pe po pp CCC mese ee ly jm E peme e gt gt o E PR ee O O D ETT fire dE gt ee E e e O TA py fer foo Y fees fosos ES eE E OL E A e AMA O CE 10 ArcPad Zoom 48MC RE O e Sta Alone O pee Step 40 RDM UID RDM L ArcPad Zoom 48MC ses E CE PE FO Load d C Sw Upd On Off 12 ArcPad Zoom 48MC 6 Control menu The ArcPad Zoom 48MC is equipped with 2 line LCD display which allows to set the fixture s behaviour according to your needs obtain information on its operation control various range of effects and lastly program it if it has to be used in a stand alone mode Control board The four control buttons on the front have the following functions Y ESCAPE button leaves menu without saving changes lt l ENTER button ent
17. oom 48MC DMX connection Power DMX Power DMX The junction box allows to connect several fixtures in a daisy chain of the power data cable Use the 3 x 1 5mm power cable to connect the first junction box with the mains and the power data cable for connecting fixtures each other Do not overload the supply line and the connecting leads The max number of connected fixtures in a daisy chain depends on input voltage 13 fixtures at power supply 230V for power cable 3 x 1 5mm 6 fixtures at power supply 120V for power cable 3 x 1 5mm You have to take into account the the length of power data cable circuit breaker etc at projecting of the fixtures installation 3 3 Wireless DMX operation The wireless version of the ArcPad Zoom 48MC ArcPad Zoom 48MC W is equipped with the Lumen Radio CRMX module and antenna for receiving DMX signal CRMX module operates on the 2 4 GHz band 1 Select wireless DMX input from the menu PErS PErs gt dMX In gt Wireless 2 To link the fixture with DMX transmitter The fixture can be only linked with the transmitter by running the link procedure at DMX transmitter After linking the level of DMX signal 0 100 is displayed in the menu item Stat Special gt Wireless gt Stat 3 To unlink the fixture from DMX transmitter The fixture can be unlinked from receiver via the menu item Unlink Special gt Wireless gt Unlink ArcPad Zoom 48MC 4 ArcPad Zoom 48MC
18. ressing any button on the control panel Contrast Use this function to adjust contrast of the display 0 100 Backlight Use this function to adjust backlight of the display 0 100 C Cal M Colour calibration mode If the functin is on the white output 2700K 8000K from the fixture and also mixed colours is more uniform C Mix M Colour mixing mode This item allows switching into RGBW or CMY mode In the CMY mode the white 8bit and white 16 bit channels are not active Dimer C Dimmer curve This menu item allows to set linear Linear or square law SqL dimmer curve Temp Uni Temperature unit Use the menu item to change temperature unit from C to F LEf Pos Init effect positions Use the menu to set all effects to the desired positions at which they will stay after switching the fixture on without DMX signal connected Defaults The menu item allows to set all fixture parameters to the default factory values 6 4 Manual Control Manual Use the menu to control all fixture channels by means of the control panel Displayed menu items depend on selected DMX mode 6 5 Test program Test Prg Use this menu item to run a special demo test sequences without an external controller which will show you some possibilities of using ArcPad Zoom 48MC 14 ArcPad Zoom 48MC 6 6 Stand alone St Alone Auto Run Presetting playback This function allows you to select the program which will be played in the stand
19. tand for ArcPad Zoom 48MC P N 10980235 20 ArcPad Zoom 48MC 9 Cleaning and maintenance DANGER Disconnect from the mains before starting any cleaning or maintenance work Rinse off loose dirt with low pressure water spray Wash the housing with a soft brush or sponge and a mild non abrasive washing detergent Rinse it Maintenance and service operations are only to be carried out by a qualified person Should you need any spare parts please use genuine parts 9 1 Replacing a fuse This replacement has to be realized by a qualified person or Anolis service worker only 9 2 Disposing of the product To preserve the environment please dispose or recycle this product at the end of its life according to the local regulations and codes Specifications are subject to change without notice November 2 2015 21 ArcPad Zoom 48MC 22
Download Pdf Manuals
Related Search