Advantech HIT-W151 User Manual Ed1
Contents
1. 51 Healthcare Infotainment Terminal AD ANTECH Enabling an Intelligent Planet Copyright The documentation and the software included with this product are copyrighted 2011 by Advantech Co Ltd All rights are reserved Advantech Co Ltd reserves the right to make improvements in the products described in this manual at any time without notice No part of this manual may be reproduced copied translated or transmitted in any form or by any means without the prior written permission of Advantech Co Ltd Information provided in this manual is intended to be accurate and reliable How ever Advantech Co Ltd assumes no responsibility for its use nor for any infringe ments of the rights of third parties which may result from its use Acknowledgements Intel and Pentium are trademarks of Intel Corporation Microsoft Windows and MS DOS are registered trademarks of Microsoft Corp All other product names or trademarks are properties of their respective owners Declaration of Conformity FCC Class B Note This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installa tion This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful inter2. este 1 eI 2 System 3 Hardware Description 5 General Specifications 4 6 Mechanical Specifications 7 2 2 1 Mechanical Specifications 7 2 2 2 Mechanical Drawing for Rear 1 8 External Viewer 8 2 9 1 TN 8 2 3 2 Side amp Bottom View 9 2 33 Rear VIEW 9 Software Description 11 Windows XP Embedded Software Specifications 12 Design Requirements 15 Environmental Specifications 16 re O TAO 16 o AA 17 Installation for Terminal 18 Installation for Handset For PIT Series ONlY 19 Installation for Remote Controller For PIT Series Only 20 Installation for Am 21 vii HIT W151 User Manual HIT W151 User Manual viii Introduction This chapter briefly introduces the HIT W151 product Overview E System Configuration 1 1 Overview The HIT W151 Healthcare Infotainment Terminal is a standard Advantech product with built in Windows XP Embedded OS In addition to providing hospital beds
3. 6 11 200 4 Smartcard ALCOR micro USB smartcard reader Rev 5 11 9520 7 Reader m Touch Elo TouchSys 2216 AccuTouch USB Rev 4 4 0 0 WLAN SParkLan WIFI module Rev 1 2 3 0 Embedded Application Software B Advantech SUSI SUSI Demo Program m SI iortcut to d jsiDen IO HIT W151 User Manual 12 1 2 LED Indicator Control SUSIDemo PCM 8600 1 13 04 07 2009 LED Switch VA Ccrizal 1 0 Corwal ED St At is LED OFF LED ON LCD Panel Brightness Control SUS Demo PCM 8600 F1 13 04 07 2009 LED Switch Ya Conhel 1 0 Coriroi Brightness Control 13 HIT W151 User Manual HIT W151 User Manual 14 Design Requirements This Chapter describes the design requirements of the HIT W151 E Environmental Specifications E Reliability 4 1 4 2 Environmental Specifications Temperature amp Humidity M Operating temperature 0 40 C E Storage temperature 0 60 C m Relative humidity 0 95 RH Non condensed Case Panel Temperature B Less than 40 C 25 C ambient temperature front bezel Safety B CE EMI m FCC class B approved Vibration E 10 18 Hz 1 5 mm peak to peak displacement 18 500 Hz 1 acceleration Reliability MTBF m 20 000 hours Touchscreen 1 million touch actuation times on a single point with a 5 8 diameter silicon fin ger under a 350 g load at 2 Hz B Power Requirements DC Input Voltage 19 V m Power Co
4. VV x 285 x 50 8 D mm 400 00 50 80 B Carton Dimensions 620 VV x 540 x 180 D excludes accessories box Mounting System Back box for wall mounting m Gross Weight 5 0 kg 7 HIT W151 User Manual m Net Weight 3 7 kg VESA Mount 75 75 mm or 100 100 mm B Screws M4 10 mm m 2 2 2 Mechanical Drawing for Rear I O A DC Inlet H Power Switch B Gigabit LAN x 2 I USB port C Audio Jack Right Line in Left MIC J 3 in 1 Memory card reader D USB2 0x4 MS amp SD amp MMC E GPIO x 1 K Barcode Scanner optional VGAx 1 L Smart Card Reader optional G COM x2 2 3 External View 2 3 4 Front View Front View Terminal HIT W151 User Manual 8 2 3 2 Side amp Bottom View 50mm amm 284mm 2 3 3 Rear View Rear View Terminal 9 HIT W151 User Manual HIT W151 User Manual 10 Software Description This Chapter describes the soft ware features of the HIT W151 E Windows XP Embedded Soft ware Specifications 3 1 Windows XP Embedded Software Specifications Real Time OS Kernel B Windows XPE 7 Language Version Driver List B Chipset Intel ICH8M Rev B Graphics Intel GMA500 Rev B Audio Realtek Audio ALC880 Rev 5 10 0 5512 m LAN Marvell Yukon Ethernet Controller Rev 8 61 7 3 Camera D Max UVC 1 3M Webcam Rev
5. ference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interfer ence to radio or television reception which can be determined by turning the equip ment off and on the user is encouraged to try to correct the interference by one or more of the following measures or relocate the receiving antenna E Increase the separation between the equipment and receiver B Connect the equipment into an outlet on a circuit different from that to which the receiver is connected m Consult the dealer or an experienced radio TV technician for help Warning Any changes or modifications made to the equipment which are not expressly approved by the relevant standards authority could void your A authority to operate the equipment Caution Danger of explosion if battery is incorrectly replaced Replace only with the same or equivalent type recommended by the manufacturer Dis pose of used batteries according to the manufacturer s instructions Part No 2008W15100 Edition 1 Printed in Taiwan March 2011 HIT W151 User Manual ii Technical Support and Assistance 1 Visit the Advantech web site at www advantech com support where you can find the latest information about the product 2 Contact your distributor sales representative or Advantech s customer service center for technical support if you need additional assista
6. 2 0 ports 2 x Gigabit Ethernet Ports Stereo Speaker 1Wx2 Bus Expansion MINI PCle Dimensions W x H x D 400 mm W x 285 mm c 50 3 mm D 15 8 x 11 26 x 1 98 Weight 5 kg 11 Ib Enviromental Specifications Operating Temperature 0 40 Relative Humidity 10 95 40 non condensing Operating Humidity 20 to 90 No Condensation Operating Atmospheric Pressure 700 1060 hPa Storage Humidity 1096 9596 No Condensation Storage Atmospheric Pressure 700 1060 hPa Transportation Temperature 20 60 Transportation Humidity 10 95 No Condensing Transportation Atmo spheric Pressure 700 1060 hPa Vibration 1G Shock 10 G peak acceleration 11 msec duration EMC BSMI CE FCC Safety CB CE UL CCC BSMI Power Output Rating 12 24 V Size Type 15 6 TFT LCD Max Resolution 1366 x 768 Max Color 262K LCD Display Pixel Pitch mm 248 25 H x 248 25 V Brightness cd m 300 View Angle 170 160 Backlight 50 000 hrs HIT W151 User Manual Type Analog Resistive 5 Wire Touch window Resolutions Continuous Light T issi 80 Touch Screen ig ransmission 6 Controller USB Storage Driver Windows XP 7 XPE Linux Durability Touches 10 million 2 2 Mechanical Specifications 2 2 1 Mechanical Specifications Terminal System Dimensions 400
7. e who connects additional equipment to the signal input part or signal output part is configuring a medical system and is therefore responsi ble that the system complies with the requirements of the system standard IEC 60601 1 1 The unit is for exclusive interconnection with IEC 60601 1 certified equipment in the patient environment and IEC 60XXX certified equipment out side of the patient environment If in doubt consult the technical services department or your local representative A user must not allow SIP SOPs and the patient to come into contact with one another at the same time The sound pressure level at the operator s position according to IEC 704 1 1982 is no more than 70dB A DISCLAIMER This set of instructions is given according to IEC 704 1 Advantech disclaims all responsibility for the accuracy of any statements contained herein Note X Attention please thoroughly consult the accompanying documentation Caution This product HIT W151 is only used with the qualified amp certificated power adapter listed below Medical SINPRO ELECTRONICS CO LTD model MPU50 107 Out put 16 21Vdc 50W max SET UP19Vac 2 634 ITE FSP GROUP INC model FSPO90 DMBB1 Output 19Vdc 4 74A Max 90W max V HIT W151 User Manual HIT W151 User Manual vi Contents Chapter Chapter Chapter Chapter Chapter 1 1 1 1 2 2 2 1 2 2 2 3 3 1 4 1 4 2 5 1 5 2 5 3 5 4
8. ide patient information remote monitoring and care functions the CPU and the LAN enabled architecture of the HIT W151 terminal also serves as an integrated hospital gateway device The HIT W151 is equipped with an Intel Atom 1 6GHz Dual core processor 15 6 wide full flat touchscreen onboard dual Giga LAN port and audio It plays a key role as a hospital bedside care and monitoring solution and connects service calls and LED light signals of a hospital room through the LAN to other parts of the hospital SWAT CARO READER HIT W151 User Manual 2 1 2 System Configuration The block diagram of a HIT W151 Healthcare Infotainment Terminal based on Hos pital bedside environment is shown in the following diagram MODE ee ann 1 HX CMOS Camera Module 2 3 M Pixel RABEN rd CABLE1 I USB CABLE 5 1 0 17CM 1700008826 CABLE ____ OA 1 bas und omore HDD CABLE Pesa MODULE10 I l ll eammmmmmmmmmm CABLES ET SQFlash I 627 con Temp L Il L_ 14 Inverter pe 2 1 ODO ie IL GL 1 acabo Te2 0000m1 numi home 968EMS0029 1254001261 INV CABLE 7P 2 0 20cm MODULES I LI Egs CABLES E E den ros Bir H um ooo 1 HIT M B 3 xoexoex LI Gerasemas uo 8 b Ee 5 RFID Module E 1 USB CABLE 5P 2 0 17CM F
9. ingerprint SERE SNS GABLEM 4 H USB Fingerprint reader MTO A D510 ICH8 M E MODULE4 MSR250HK 10 POCO H pe L USBTABLESSZ0T 0M 3 A 1 mEREEREREEEEREEEERMENNEN L I MSR L PWR geo f ST a a L H F EEN UART CABLE 6P 1 25 17CM I 19 HAN Lene We ______ 19 DC Adapter i 1 9688000450 DC Z PHR pr E i peon ua NN J USB CABLE 8P 1 25 20CM I pr end i 1 sa Module USE 3 3V 810021110000 9680005765 MODULE6 EZM110PU mm D 1 1 Power Core OA pe Smart Card I 1700001524 dE I BRD4 LI kennen TE mmm mane E Charger E Board a H Optional WCANMAW NE7SS EEE 302 11b gin Mini PCle 968EMWO0021 3 HIT W151 User Manual HIT W151 User Manual Hardware Description This Chapter describes the hard ware features of the HIT W151 General Specifications E Mechanical Specifications m External View 2 1 General Specifications Processor System Intel Atom 0510 Dual Core 1 67 GHz Pro CPU cessor Chipset Intel N450 D510 ICH8M L2 Cache 512 KB 1 MB FSB Speed 667 MHz Memory DDR2 200 pin SODIMM x 2 0 Supports 1 x internal CompactFlash 3 in 1 Card Reader Supports MS amp SD amp MMC Webcam Standard built in 2M CMOS camera HDD 1 2 5 internal SATA HDD interface Network 2 x Gigabit Ethernet Ports 2 x ports VGA port GPIO Mic in Line out Ports 4 x USB
10. is sion of the publisher All brand and product names are trademarks or registered trademarks of their respective companies O Advantech Co Ltd 2011
11. nce Please have the following information ready before you call Product name and serial number Description of your peripheral attachments Description of your software operating system version application software etc A complete description of the problem The exact wording of any error messages Warning 1 Input voltage is rated 19 DC Mode 2 Packing Please carry the unit with both hands handle with care 3 Maintenance To properly maintain and clean the surfaces use only approved products or clean with a dry applicator iii HIT W151 User Manual Safety Instructions 10 11 12 13 14 19 16 Read these safety instructions carefully Keep this User Manual for later reference Disconnect this equipment from any AC outlet before cleaning Use a damp cloth Do not use liquid or spray detergents for cleaning For plug in equipment the power outlet socket must be located near the equip ment and must be easily accessible Keep this equipment away from humidity Put this equipment on a reliable surface during installation Dropping it or letting it fall may cause damage The openings on the enclosure are for air convection Protect the equipment from overheating DO NOT COVER THE OPENINGS Make sure the voltage of the power source is correct before connecting the equipment to the power outlet Position the power cord so that people cannot step on it Do not place a
12. nsumption less than 60 VV HIT W151 User Manual 16 Installation This Chapter describes the instal lation of the HIT W151 E Installation for Terminal E Installation for Handset For PIT Series Only E Installation for Remote Control ler For PIT Series Only B Installation for Arm 5 1 Installation for Terminal Step 1 Fix Hook Step 2 Fix ARM Handset Bracket for PIT Series only Remote Control Bracket for PIT Series only R S M3 L6 ST NI Q ty 2 R S M3 L6 ST NI NK Q ty 2 HIT W151 User Manual 18 5 2 Installation for Handset For PIT Series Only Step 1 Fix Hook only R S M4 Q ty 4 R S M3 L6 ST NI NK Qy 2 19 HIT W151 User Manual 5 3 Installation for Remote Controller For PIT Series Only Step 1 Fix Hook Step 2 Fix ARM Handset Bracket for PIT Series only Remote Control Bracket for PIT Series only R S M4 Q ly 4 R S M3 L6 ST NI NK Q ty 2 HIT W151 User Manual 20 5 4 Installation for Arm Step 1 Fix Hook only R S M4 Q ty 4 21 HIT W151 User Manual AD ANTECH Enabling an Intelligent Planet www advantech com Please verify specifications before quoting This guide is intended for reference purposes only All product specifications are subject to change without notice No part of this publication may be reproduced in any form or by any means electronic photocopying recording or otherwise without prior written perm
13. nything over the power cord All cautions and warnings on the equipment should be noted If the equipment is not used for a long time disconnect it from the power source to avoid damage by transient overvoltage Never pour any liquid into an opening This may cause fire or electrical shock Never open the equipment For safety reasons the equipment should be opened only by qualified service personnel If one of the following situations arises get the equipment checked by service personnel a The power cord or plug is damaged b Liquid has penetrated the equipment c The equipment has been exposed to moisture d The equipment does not work well or you cannot get it to work according to the user s manual e The equipment has been dropped and damaged f The equipment has obvious signs of breakage DO NOT LEAVE THIS EQUIPMENT IN AN ENVIRONMENT WHERE THE STORAGE TEMPERATURE MAY GO BELOW 20 C 4 F OR ABOVE 60 C 140 F THIS COULD DAMAGE THE EQUIPMENT THE EQUIPMENT SHOULD BE IN A CONTROLLED ENVIRONMENT If your computer clock loses a significant amount of time or the BIOS configura tion resets to default the battery has no power Caution 1 Do not replace power adaptor yourself Please contact a qualified technician or your retail 2 The computer is provided with a battery powered real time clock circuit There is a danger of explosion if battery is incorrectly replaced Replace only with same or equi
14. valent type recom mended by the manufacturer Discard used batteries according to the manufacturer s instructions 3 Cleaning During normal use of the HIT W151 may become soiled and should therefore be cleaned regularly Agents Alcohol or water 4 End of Product for Environmental protection please follow national requirements to dispose of unit HIT W151 User Manual iv 17 18 19 20 21 22 23 24 29 CLASSIFICATION Supplied by Class adapter No applied parts Continuous operation No AP or APG category Follow national requirements to dispose of unit Maintenance To properly maintain and clean the surfaces use only approved products or clean with a dry cloth Contact information No 1 Alley 20 Lane 26 Rueiguang Road Neihu District Taipei Taiwan 114 R O C TEL 02 2792 7818 PE le Medical Equipment With Respect to Electric Shock Fire and Mechanical Hazards Only C US In Accordance with UL 60601 1 CANICSA C22 2 No 601 1 XXXX This equipment is not to be used as a life support system Accessory equipment connected to the analog and digital interfaces must be in compliance with the respective nationally harmonized IEC standards i e IEC 60950 for data processing equipment IEC 60065 for video equipment IEC 61010 1 for laboratory equipment and IEC 60601 1 for medical equipment Furthermore all configurations must comply with the system standard IEC 60601 1 1 Anyon
Download Pdf Manuals
Related Search