Set up and user manual for the VPC5-704CME VPC5
Contents
1. SIDE VIEW 1 4 20UNC 70 0mm MA at mt FRONT VIEW TOP VIEW Manual version V1 1 This manual is subject to change without notice2. iris SPEED 0 255 Sets the convergence speed of the iris SHUTTER AGC AUTO HIGH LUMINANCE MODE SHUT SHUT AUTO IRIS only SHUT can be selected if LENS is in MANUAL mode BRIGHTNESS 0 255 Adjusts the brightness level LOW LUMINANCE MODE AGC OFF Auto Gain Control on or off BRIGHTNESS x0 25 x0 50 x0 75 x1 00 Amount of AGC applied in low lighting conditions MANUAL MODE SHUT OFF Auto gain control SHUTTER Select the shutter speed 1 50 1 120 1 250 1 500 1 1000 1 2000 1 4000 1 10000 AGC Sets the AGC gain applied dB for ME manual exposure 6 12 18 24 30 36 42 44 8dB WHITE BAL ATW Auto Trace White balance SPEED 0 255 Adjusts the pull in speed of ATW DELAY CNT 0 255 Sets the time based hysteresis of ATW ATW FRAME X0 5 X1 X1 5 X2 Sets the pull in frame magnification ENVIROMENT indoor outdoor Preset for either indoor or outdoor applications of the ATW PUSH Wide range Auto White Balance mode AWB USER1 amp 2 Both USER 1 amp 2 can be individually set up for specific applications The gain values for USER 1 are biased towards the camera being installed outdoors and USER 2 setting are biased towards being installed internally B GAIN 0 255 R GAIN 0 255 ANTICR Colour rolling suppression ideal for internal use when fluorescent lighting is present MANUAL The B and R gain values for manual WB are set on this scre
3. following WARNING CAUTION and Note statements identify potential hazards that can occur if the equipment is not handled properly WARNING Caution Improper use of this eguipment can cause eguipment damage Improper use of this eguipment can cause severe bodily injury or eguipment damage Note Notes contain important information about a product or procedure RoHS Announcement All lead free products offered by the company comply with the reguirements of the European law on the Restriction of Hazardous Substances RoHS directive which means our manufacture processes and products are strictly lead free and without the hazardous substances cited in the directive The crossed out wheeled bin mark symbolizes that within the European Union the product must be collected separately at the product end of life This applies to your product and any peripherals marked with this symbol Do not dispose of these products as unsorted municipal waste 59 This apparatus is manufactured to comply with the radio interference A Declaration of Conformity in accordance with the following EU standards has been made The manufacturer declares that the product supplied with this document is compliant the provisions of the EMC Directive 2004 108 EC the CE Marking Directive 93 68 EEC and all associated amendments This symbol indicates electrical warnings and cautions This symbol indicates general warnin
4. 625KHz H x 50Hz V Sync system Internal Electronic shutter 1 50 1 10 000 sec Min illumination Colour Colour 0 15Lux Colour Colour 0 15Lux F1 2 0 15Lux Mono 0 01Lux 0 15Lux Mono 0 01Lux IR Cut Filter Fixed Mechanical Fixed Mechanical Video output 1 0Vp p 75 ohm composite S N Ratio 50dB AGC off OSD Control Tactile buttons on rear of camera T ATR Luminance L Contrast L LM Backlight OFF D Day Night Auto delay 0 255 secs Colour BW BW or BW with BURST 2 Motion Det Off 4 areas Privacy On colour mosaic Off 4 zones White ATW PUSH USER1 USER2 ANTI CR MANUAL PUSH Balance LOCK S AGC Off Exposure Auto Iris Auto Iris Electronic Shutter Brightness 0 255 steps 2 Contrast 0 255 steps Sharpness 0 255 steps Hue 0 255 steps Gain 0 255 steps NR OFF Y C Y C Mirror On Off Camera ID 2 26 characters On edit position Off Language GER RUS POR SPA POWER Power source 12VDC 15 24VAC 10 100 240VAC 50 60Hz Consumption 3 5W 0 3A 4W 0 055A Power input 2 pin terminal block AC Cord Video output BNC connector Q Operating Temp 10 C 50 C Storage Temp 10 C 60 0 90 non condensing 5 Dimensions 70 W x 60 H x 124 5 L mm unit 2 280 W x 70 H x 140 D boxed Weights 252g net 410g gross 11 DIMENSIONS 124 5mm
5. Installation Manual Set up and user manual for the VPC5 704CME VPC5 700CME VPC5 704DNE VPC5 700DNE cameras Before You Begin Read these instructions before installing or operating this product Note This installation should be made by a gualified service person and should conform to local codes This manual provides installation and operation information To use this document you must have the following minimum qualifications A basic knowledge of CCTV systems and components A basic knowledge of electrical wiring and low voltage electrical connections Intended use Only use this product for its designated purpose refer to the product specification and user documentation Customer Support For assistance in installing operating maintaining and troubleshooting this product refer to this document and any other documentation provided If you still have questions please contact Norbain Technical Support and Sales Norbain Ltd 210 Wharfedale Road IQ Winnersh Triangle Wokingham Berks RG41 5TP UK 44 0 118 912 5000 Netherlands 31 0 76 579 2577 Belgium 32 0 3 369 8080 South Africa 27 0 11 887 1546 Portugal 351 234 301900 Spain 34 91 503 06 78 Middle East 971 4 881 14332 Rest of world 44 118 912 5000 Note You should be at the equipment and ready with details before calling Technical Support Conventions Used in this Manual Boldface or button icons highlight command entries The
6. ON OFF Enables disables the motion detection AREA SEL 1 4 Selects the motion detection area TOP 0 244 O top BOTTOM 0 244 244 bottom LEFT 0 474 O left RIGHT 0 474 474 right PRIVACY AREA SEL 1 4 Selects the motion detection area TOP 0 244 O top BOTTOM 0 244 244 bottom LEFT 0 474 O left RIGHT 0 474 474 right COLOUR 1 8 Sets the colours of the privacy zones TRANSP 0 00 0 50 0 75 1 00 Sets the transparency of the privacy zone area if colour is selected MOSAIC ON OFF Sets the mosaic function as the privacy to ON or OFF Note when mosaic ON transparency needs to be set at 0 00 Privacy zones can only be 1 colour OR mosaic and not mixed DAY NIGHT AUTO BURST ON OFF Allows the colour burst signal in monochrome mode to be removed DELAY CNT 0 255 secs Sets the hysteresis time before switching between colour mono amp mono colour to reduce the hunting effect DAY gt NIGHT 0 255 Sets the threshold for switching from day to night operation NIGHT gt DAY 0 255 Sets the threshold for switching from night to day operation COLOUR colour only operation B W monochrome only operation BURST ON OFF Allows the colour burst signal in monochrome mode to be removed NR 2D DNR This is used to remove noise from the image in low light conditions when AGC is applied NR MODE OFF Y C Y C Sets the 2D NR filter mode Y LEVEL 0 15 Sets the Y
7. cts VENTILATION Openings in the equipment if any are provided for ventilation to ensure reliable operation of the unit and to protect if from overheating These openings must not be blocked or covered POWER SOURCES The equipment should be operated only from the type of power source indicated on the marking label If you are not sure of the type of power supplied at the installation location contact your dealer For equipment designed to operate from battery power refer to the operating instructions GROUNDING OR POLARIZATION Equipment that is powered through a polarized plug a plug with one blade wider than the other will fit into the power outlet only one way This is a safety feature If you are unable to insert the plug fully into the outlet try reversing the plug Do not defeat the safety purpose of the polarized plug Alternate Warning If the equipment is powered through a three way grounding type plug a plug having a third grounding pin the plug will only fit into a grounding type power outlet This is a safety feature Do not defeat the safety purpose of the grounding type plug If your outlet does not have the grounding plug receptacle contact your local electrician CORD AND CABLE PROTECTION Route power cords and cables in a manner so to protect them from damage by being walked on or pinched by items places upon or against them LIGHTNING For protection of the equipment during a lightning storm or when it is left u
8. e manufacturer or that have the same characteristics as the original part Unauthorized substitutions may result in fire electric shock or other hazards SAFETY CHECK Upon completion of any service or repairs to the equipment ask the service technician to perform safety checks to verify that the equipment is in proper operating condition FIELD INSTALLATION The installation of equipment should be made by a qualified service person and should conform to all local codes CAUTION THESE SERVICING INSTRUCTIONS ARE FOR USE BY QUALIFIED SERVICE PERSONNEL ONLY TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT PERFORM ANY SERVICING OTHER THAN THAT CONTAINED IN THE OPERATING INSTRUCTIONS UNLESS YOU ARE QUALIFIED TO DO SO Use certified Listed Class 2 power supply transformer only CE COMPLIANCE STATEMENT WARNING This is a Class A product In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures VI TABLE OF CONTENTS INTRODUCTI CONTENTS OF PACKAGE E OSD ADJUSTMENT OSD MAIN MENU TREE OSD MENUSETTINGS SPECIFICATIONS DIMENSIONS VII INTRODUCTION Features 700TVL Colour amp Monochrome resolutions 1 3 Sony EXview HAD CCD II with Effio e DSP 0 15Lux Colour F1 2 Sensitivi
9. en LEVEL 14 57 PUSH LOCK PUSH LOCK fixes the white balance and should only be used when there is no change the illumination level If there are any changes in illumination this must be reset by pushing the enter button again to adjust to new illumination level BACKLIGHT OFF Reduces over illumination of back lit subject HLC Inverts over bright white light to black Peak White Inversion ADJUST MIRROR ON OFF Inverts image horizontally BRIGHTNESS 0 255 Sets the screen brightness CONTRAST 0 255 Sets the screen contrast SHARPNESS 0 255 Sets the screen sharpness HUE 0 255 Adjusts the hue GAIN 0 255 Adjusts the gain ATR ATR Adaptive Tone Reproduction allows adjustment of the image to assist with widely contrasting scenes of view LUMINANCE LOW MID HIGH Sets the extent of the luminance compression CONTRAST LOW MIDLOW MID MIDHIGH HIGH Sets the extent of the contrast enhancement MOTION DET DETECT SENSE 0 127 Sets the motion detection sensitivity O low sensitivity 127 high sensitivity BLOCK DISP OFF ON ENABLE Applies a motion block trace in the selected area To define the area select Enable and push centrally on the tactile switch Use the tactile switch to navigate to the blocks you want to Disable and not include in motion trace To return to the menu push and hold central tactile switch for 2secs and release MOTION AREA
10. filter Luminance strength C LEVEL 0 15 Sets the C filter Chrominance strength CAMERA ID Sets the camera ID to ON or OFF A title of 26 characters per line can be applied CAMERA ID Use the tactile switch to navigate the cursor Pushing centrally on the tactile switch will allow selection of that CAMERAID ABCDEFGH JKLMNOPQRSTUV WXYZ0123456789 8 character The arrows at the bottom RETURN allow you to move the cursor without changing the CHR1 character Allows you to edit line 1 CHR2 Allows you to edit line 2 CLR Inserts a space POS Allows you adjust the location of the camera ID title display SYNC INT Internal synchronization only on both LV and Mains models LANGUAGE LANGUAGE select between English Japanese German French Russian Portuguese 8 Spanish CAMERA RESET CAMERA RESET Returns the camera to the factory default settings SAVE ALL SAVE ALL Saves all the changes made in the menu EXIT EXIT Exits the menu and does not save changes made 10 SPECIFICATIONS MODEL 704CME 704DNE 700CME 700DNE Resolution 7OOTVL colour and monochrome Image sensor 1 3 SONY EXview HAD CCD Total pixels 1028 H x 596 V Effective pixels 976 H x 582 v Scanning system 2 1 Interlace Scanning freq PAL 15
11. gs and cautions NORBAIN LTD reserves the right to make changes to the product and specification of the product from time to time without prior notice WARNINGS AND CAUTIONS To reduce the risk of fire or electric shock do not insert any metallic objects through the ventilation grills or other openings on the equipment CAUTION CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL IV IMPORTANT SAFEGUARDS 1 10 READ AND RETAIN INSTRUCTIONS Read the instruction manual before operating the eguipment Retain the manual for future reference CLEANING Turn the unit off and unplug from the power outlet before cleaning Use a damp cloth for cleaning Do not use harsh cleansers or aerosol cleaners ATTACHMENTS Do not use attachments unless recommended by manufactured as they may affect the functionality of the unit and result in the risk of fire electric shock or injury MOISTURE Do not use equipment near water or other liquids ACCESSORIES Equipment should be installed in a safe stable location Any wall or shelf mounting accessory equipment should be installed using the manufacture s Instructions Care should be used when moving heavy equipment Quick stops excessive force and uneven surfaces may cause the equipment to fall causing serious injury to persons and obje
12. nattended and unused for long periods of time unplug the unit from the wall outlet Disconnect any antennas or cable systems that may be connected to the equipment This will prevent damage to the equipment due to Lightning or power line surges 11 12 13 14 15 16 17 18 OVERLOADING Do not overload wall outlets and extension cords as this can result in a risk of fire or electric shock SERVICING Do not attempt to service the video monitor or equipment yourself as opening or removing covers may expose you to dangerous voltage or other hazards Refer all servicing to qualified service personnel DAMAGE REQUIRING SERVICE Unplug the equipment from the wall outlet and refer servicing to qualified service personnel under the Following conditions A When the power supply cord or the plug has been damaged If liquid has spilled or objects have fallen into the Unit C If the equipment has been exposed to water or other liquids D If the equipment does not operate normally by following the operating instructions adjust those controls that are covered by the operating instructions as Improper adjustment for other controls may result in damage to the unit E If the equipment has been dropped or the casing is damaged F When the equipment exhibits a distinct change in performance REPLACEMENT PARTS When replacement parts are required be sure the service technician uses replacement parts specified by th
13. r into the OSD menu push the centre button and navigate using the up down left and right buttons If there is an arrow to the right of the menu function this denotes that there is an accessible sub menu function and this is accessed via the enter command with the tactile switch Low voltage Mains Voltage OSD MAIN MENU TREE SETUP MENU page 1 LENS SHUTTER AGC LENS SHUTTER AGC WHITE BAL BACKLIGHT AUTO IRIS AUTO PICT ADJUST MANUAL MANUAL ATR MOTION DET NEXT page2 RETURN RETURN EXIT SAVE WHITE BALANCE BACKLIGHT ATW BLC PUSH HLC USER 1 USER 2 ANTI CR MANUAL PUSH LOCK RETURN RETURN PICTURE ADJUST ATR MOTION DET MIRROR LUMINANCE DETECT SENSE BRIGHTNESS CONTRAST BLOCK DISP CONTRAST MONITOR AREA SHARPNESS AREA SELECT HUE GAIN RETURN RETURN RETURN SETUP MENU page 2 PRIVACY PRIVACY DAY NIGHT DAY NIGHT NR AREA SEL AUTO CAMERA ID COLOUR COLOUR SYNC TRANSP B W LANGUAGE MOSAIC CAMERA RESET BACK page 1 EXIT SAVE RETURN RETURN NR CAMERA ID NR MODE titling Y LEVEL C LEVEL RETURN RETURN RETURN LANGUAGE CAMERA RESET ENGLISH CHINESE return the GERMAN camera to FRENCH factory RUSSIAN defaults PORTUGUESE SPANISH OSD MENU SETTINGS LENS MANUAL Manual lens only AUTO TYPE DC VIDEO Sets the type of mechanical iris Video lens is not supported MODE OPEN CLOSE AUTO Sets the type of control to be applied over the
14. ty CME version 0 15Lux Colour 0 01 Lux B W F1 2 Sensitivity DNE version Auto electronic shutter 1 50 1 10 000 and manual electronic shutter modes Day amp Night Auto delay Colour BW OSD On Screen Display via tactile switch ATR Adaptive Tone Reproduction AGC Auto Gain Control 2D DNR function Digital Noise Reduction Auto and manual white balance modes BLC Back Light Compensation HLC Peak White Inversion 4 Privacy zones colour mosaic 4 Motion detection zones Functions Mirror Brightness Sharpness Hue Contrast Gain Multi language support English Japanese German French Russian Portuguese Spanish 12VDC or 24VAC operation on 704 models only If using DC 12V power adaptor Please use a power supply capable of supplying over 600mA 100 240VAC operation on 700 models only Use Certified Listed Class 2 power source only CONTENTS OF PACKAGE Installation of the camera must be performed by qualified service personnel in accordance with all local and national electrical and mechanical codes Carefully remove the camera and its accessories from the carton and verify that they were not damaged in shipment The content of the package includes 1 Camera 2 Mini DIN connector for video or dc type auto iris lens 3 ring adapter 4 This manual OSD ADJUSTMENT The buttons on the rear of the camera allows both navigation and changes to the OSD Menu To ente
Download Pdf Manuals
Related Search