ATOM 360_说明书_20130523.cdr
Contents
1. see its user manual e When the flash unit receives wireless signals is shown on the LCD display 11 Sync Triggering The Sync Cord Jack 9 is a 3 5mm plug Insert a trigger plug here and the flash will be fired synchronously with the camera shutter 12 PC Sync Triggering Insert one end of a PC sync cable into the PC Sync Socket 10 of the flash unit and the other end into the PC Sync Socket on the camera The flash unit will fire when the camera s shutter release button is pressed A Protection Function Over Temperature Protection e To avoid overheating and deteriorating the flash head do not fire more than 75 continuous flashes in fast succession at 1 1 full power After 75 continuous flashes allow a rest time of at least 10 minutes e If you fire more than 75 continuous flashes and then fire more flashes in short intervals the inner over temperature protection function may be activated and make the recycling time about 10 to 15 seconds If this occurs allow a rest time of about 10 minutes and the flash unit will then return to normal e When the over temperature protection is started is shown on the LCD display Number of flashes that will activate over temperature protection Power Output Level Number of Flashes Approx 1 1 75 1 2 100 1 4 200 1 8 300 1 16 1 32 400 1 64 1 128 500 10 Model ATOM 360 Max Power 360Ws Guide No m ISO 100 80 m I2. BIT SCPE O LENCARTA ATOM 362 Powerful amp Portable Flash Instruction Manual E FOREWORD Before using this product Please read this user manual carefully in order to ensure your safety and the proper operation of this product Keep for future reference Thank you for purchasing a LENCARTA product ATOM 360 flash system is an ATOM 360 flash with a bare tube external power pack wireless manual power control and a range of dedicated light shaping accessories ATOM 360 is 5 to 7 times powerful as typical hotshoe flashes with the size and weight alike It offers studio quality light for outdoor and live shooting The ATOM 360 offers e Studio quality light up to 360Ws GN 80 m ISO 100 with AD S2 standard reflector Approx 23mm flash coverage when operating on a camera with the standard reflector One ATOM 360 can overpower the sun External battery pack ATOM POWER lithium 11 1V 4500mAh 0 05 4 5s recycling and 450 full power flashes Lightweight and portable even with power and accessories Wireless control on power levels and triggering with LENCARTA remote control Wide range accessories softbox beauty dish snoots color gels etc All lighting accessories fit for barebulb flashes from most brands Power adjusts from full power to 1 128 in 1 3 stop increments Stable color temperature at 5600 200K over the entire power range Multi flash Focus assist beam on off amp Hi Speed sync triggering Th
3. Dial The flash unit is not powered by itself but draws power from LENCARTA ATOM POWER sold separately 03 e Included Accessories 1 Flash tube 1 2 Protecting bag 1 3 Mini stand 1 4 Off camera adapter 1 5 Reflector 1 6 Power cable 1 7 Reflector diffuser 2 8 Instruction manual 1 24 A 5 END u yis LLE e Separately Sold Accessories 3 The product can be used in combination with the following accessories sold separately so as to achieve best photography effects Remote Control Softbox Beauty Dish Fold up umbrella Snoots Light stand etc 1 Rotate Accessory Locking Ring 2 counter clockwise until it is loosen 2 Insert the reflector into the Accessory Mount 1 3 Rotate Accessory Locking Ring 2 clockwise to lock it up Do not over tighten 04 2 Match the red dot on the base of the flash tube with the red dot in the Tube Socket 4 Push the flash tube in until it is securely seated into the socket 1 Remove the reflector or other accessories from the flash head Connecting to a Power Pack 3 Turn on the power pack Normally the flash unit will be fully charged and ready to work 1 Before connecting make sure that the power pack is turned off 2 Plug one end of Power Cable into Power Socket 7 of the flash unit and insert the other end into the output socket of the power pack The flash unit is not powered by itself but draws pow
4. SO 100 with standard reflector Approx 28mm flash coverage when operating on a camera with the standard reflector Vertical Rotation Angle 15 to 90 Horizontal Rotation Angle 0 to 270 Power Supply ATOM POWER Full Power Flashes 450 ATOM POWER Recycle Time Approx 0 05 4 5s with ATOM POWER Color Temperature 5600 200K Flash Duration 1 300s 1 10000s Dimension 75 95 220mm flash tube amp reflector not included Net Weight 780g flash tube amp reflector not included Shut down the device immediately should abnormal operation be detected Avoid sudden impacts and the lamp should be dedusted regularly It is normal for the flash tube to be warm when in use Avoid continuous flashes if unnecessary Maintenance of the flash must be performed by our authorized maintenance department which can provide original accessories The flash tube is user replaceable Replacement tubes can be obtained from the manufacturer This product except consumables e g flash tube is supported with a one year warranty Unauthorized service will void the warranty If the product had failures or was wetted do not use it until it is repaired by professionals Disconnect the power when cleaning the unit or when changing the flashtube Changes made to the specifications or designs may not be reflected in this manual 11
5. ate over temperature protection in high speed sync triggering mode Power Output Level Number of Flashes Approx 1 1 10 112 15 1 4 20 1 8 30 8 MF Assist Beam Under poorly lit or low contrast conditions you can press MF Assist Beam Button 16 to turn on the MF assist beam in order to make it easier to autofocus When the MF assist beam is lit W is shown on the LCD display 9 Buzz Function The buzz function can be controlled by pressing BUZZ Button 17 When the buzzer is turned on is shown on the LCD display The buzzer provides an indication that the ATOM 360 flash unit has fully recycled 10 Wireless Control Function e The flash unit is built in with a Wireless Control Port 8 so that you can wirelessly adjust the power level of the flash and control the on or off of your flash focus assist lamp and buzzer as well as trigger the flash e To control the flash wirelessly you need a FT series remote control set on camera and on flash Insert its receive end into the Wireless Control Port 8 on the flash and insert the transmit end into the camera hot shoe Settings made on the 09 hotshoe mounted transmit and receive ends will be wirelessly communicated to the flash Then you can press the camera shutter release button to trigger the flash You can also hold the transmit end at hand to control your off camera ATOM 360 e For full instructions on the use of FT series remote control
6. de Stroboscopic Flash Press Mode Selection Button 18 to enter RPT mode Multi Stroboscopic flash With stroboscopic flash a rapid series of flashes is fired It can be used to capture multiple images of a moving subject in a single photograph You can set the firing frequency number of flashes per sec expressed as Hz the number of flashes and the flash output For setting procedures see the following e Press the Mode Selection Button 18 so that RPT is displayed e Press Set Button 19 to select the item to be set The item blinks e Rotate Select Dial 22 to set a desired number 07 Calculating the Shutter Speed During stroboscopic flash the shutter remains open until the firing stops Use the following formula to calculate the shutter speed required to capture the full sequence of flashes Number of flashes Firing frequency Shutter speed For example if the number of flashes is 10 and the firing frequency is 5 Hz the shutter speed should be at least 2 sec Note e Stroboscopic flash is most effective with a highly reflective subject against a dark background e Using a tripod a remote switch and an external power source is recommended e Aflash output of 1 1 or 1 2 cannot be set for stroboscopic flash e Stroboscopic flash can be used with bulb To avoid overheating and deteriorating the flash head do not use stroboscopic flash more than 10 times in succession Maximum Stroboscopic F
7. e powerful and portable ATOM 360 meets the demands of freelance commercial photographers photojournalists wedding and beach portraiture shooters event and backpack photographers photograph enthusiasts etc It is compatible with market available cameras from Canon Nikon Pentax and Olympus etc and fits for almost any flash trigger W FOR YOUR SAFETY A Always keep this product from rain or dampness to avoid fire or electric shock A This product contains high voltage electronic parts Touching the high voltage circuit inside it may result in electric shock Do not disassemble Should repairs become necessary this product must be sent to an authorized maintenance center A Stop using this product if it breaks open due to extrusion falling or strong hit Otherwise electric shock may occur if you touch the electronic parts inside it A Do not fire the flash directly into the eyes especially those of babies within short distances Otherwise visual impairment may occur When taking pictures for babies keep the flash unit at least 1 meter 3 3 feet away from them Using bounce flash to reduce light intensity is also recommended 01 A Do not use the flash unit in the presence of flammable gases chemicals and other similar materials In certain circumstances these materials may be sensitive to the strong light emitting from this flash unit and fire or electromagnetic interference may result 4 Do not leave or store the flash
8. er from ATOM POWER sold separately For the instructions of the power pack see the related user manual 05 1 Loosen the locking ring on the mounting foot 2 Slip the mounting foot of the flash unit into the camera hotshoe 3 Secure the flash unit by rotating the locking ring the direction of the row T Replacing the Off Camera Adapter The off camera adapter is useful when using the product as an off camera flash There is a 1 4 mounting hole at the bottom of the off camera adapter After replacing the adapter the flash can be used mounting on LENCARTA portable light boom LENCARTA floor light stand and almost any other light stand To install the off camera adapter 1 Use a screwdriver not included to remove the four screws at the bottom of this product Then take out the bottom part carefully as illustrated Gips lt M Y 1 2 Install the off camera adapter at the bottom of this product 3 Tighten all the screws W9 Using the Flash 1 Power Management ON OFF Power Switch 20 controls the on off of the flash unit Turn off the power pack if the flash unit will not be used for an extended period 06 2 Flash Output Flash output can be varied from 1 128th power to 1 1 full power in 1 3 stop increments To obtain a correct flash exposure use a hand held flash meter to determine the required flash output Adjust the power output by rotating Select Dial 22 The following table mak
9. es it easier to see how the stop changes in terms of f stop when you increase or decrease the flash output Figures displayed when reducing flash output level on Figures displayed when increasing flash output level When OF is shown on the LCD display it means no flash output and flash firing is turned off 3 M Mode Manual Mode Press MODE Selection Button 18 to enter M mode In this mode you can set the flash unit onto your camera hot shoe or your trigger hot shoe for firing Before shooting adjust the power output of the ATOM 360 When the camera s shutter is pressed the flash will fire Slave triggering mode is not available in M mode 4 S1 Mode S1 Slave Triggering Mode Press Mode Selection Button 18 to enter S1 mode In this mode the flash unit can function as a slave flash for creating multiple lighting effects It is respectively applicable to manual flash environment In S1 mode the flash unit will fire synchronously when the master flash fires the same effect as that by the use of radio triggers 5 S2 Mode S2 Slave Triggering Mode Press Mode Selection Button 18 to enter S2 mode In this mode the flash unit can function as a slave flash for creating multiple lighting effects It is applicable when using a TTL master flash In S2 mode the flash unit will ignore a single preflash from the master flash and will only fire in response to the second actual flash from the master 6 RPT Mo
10. lashes Flash Output l a 3 A 3 6 y 1 1 1 1 1 1 1 1 1 1 2 1 1 1 1 1 1 1 1 4 30 5 2 2 2 2 1 1 8 50 4 2 2 2 2 2 1 16 70 70 7 4 3 3 3 1 32 80 80 80 16 8 6 5 1 64 99 99 99 99 99 99 25 11128 99 99 99 99 99 99 99 we Ma 8 9 10 11 12 13 13 15 15 19 20 99 1 1 1 1 1 1 1 1 1 1 2 1 1 1 1 1 1 1 1 4 1 1 1 1 1 1 1 1 8 2 2 2 2 2 2 2 1 16 2 2 2 2 2 2 2 1 32 5 4 4 3 3 3 3 1 64 15 10 6 6 5 5 5 1 128 99 99 99 99 99 36 20 08 7 4 Hi Speed Sync Triggering To enter H mode press both Mode Selection Button 18 and Set Button 19 Press Mode Selection Button 18 again to exit 4 mode In 4H hi speed sync triggering mode you can use a hi speed sync trigger to have your flash unit synchronize with all shutter speeds of cameras max 1 8000 second up to your camera This is convenient when you want to use aperture priority for fill flash portraits Note e Hi speed sync triggering mode is effective only when the flash unit is used together with hi speed sync trigger e g Godox Cells II transceiver e Hi speed sync triggering mode is not available when the flash unit is mounted onto the camera hotshoe To avoid overheating or deteriorating the flash head the over temperature protection function will be activated automatically after 10 continuous high speed flashes and the recycle time becomes 10s longer Number of flashes that will activ
11. unit if the ambient temperature reads over 50 C e g in automobile Otherwise the electronic parts may be damaged A Be cautious when using the ATOM 360 on your camera ATOM 360 is slightly heavy so that an ATOM 360 on your camera may damage the camera hotshoe W CONTENTS 01 Foreword 01 For Your Safety 03 Names of Parts 03 Body 03 Control Panel 04 Included Accessories 04 Separately Sold Accessories 04 Installing Reflector Other Accessories 05 Attaching Flash Tube 05 Connecting to a Power Pack 05 Connecting the Flash to a Camera 06 Replacing the Off Camera Adapter 06 Using the Flash 06 Power Management 07 Flash Output 07 M Mode 07 S1 Mode 07 S2 Mode 07 RPT Mode 09 mHi Speed Sync Triggering 09 MF Assist Beam 09 Buzz Function 09 Wireless Control Function 10 Sync Triggering 10 PC Sync Triggering 10 Protection Function 11 Technical Data 11 Maintenance 09 11 12 y MN HM 14 01 Accessory Mount 08 Wireless Control Port 02 Accessory Locking Ring 09 Sync Cord Jack 03 Flash Tube 10 PC Sync Socket 04 Tube Socket 11 MF Assist Beam 05 Umbrella Mounting Hole 12 Light Sensor 06 Release Button 13 Control Panel 07 Power Socket 14 Hotshoe Stand e Control Panel 15 LCD display 16 MF Assist Beam Button 17 BUZZ Button 18 MODE Selection Button 19 SET Button 20 ON OFF Power Switch 21 Test Button Flash Ready Indicator 22 Select
Download Pdf Manuals
Related Search