I-TOP Installation, Service and User Instructions
Contents
1. Operate the appliance in accordance with the following procedure e Remove all pans from the cooking zone e Make sure the cooking zone is switched off e Power up the appliance by activating the main switch on the machine e Switch on the cooking zone and increase its power level the green indicator light corresponding to that zone should flash at regular intervals to indicate the absence of a pan e Place a pan full of water on the zone the green indicator light will remain lit steadily e Turn the power up to maximum after a few minutes the fan will be activated 12 TROUBLESHOOTING e Important Do not open up the appliance There is high voltage inside PROBLEM CAUSE CORRECTIVE MEASURE No heating There is no Check the mains indicator light power the power connection remains off appliance is switch on the not switched appliance on No heating The pan is too Use suitable indicator light small its base cookware as flashes is not flat or it recommended by the is the wrong manufacturer shape the Switch off the power pan is not and contact a positioned in qualified technician the middle of authorized by the the cooking manufacturer zone Appliance breakdown The indicator Unsuitable Use suitable light does not pan used cookware make sure inconsistent or generator too hot flash but generator the air inlets are clear heating is not l2. oil inside inside pan pan too hot lower switching off temperature level power too low Connection error between the generator and the panel 05 Potentiometer Set the power level damaged or to a value other than control knob 0 before use power not set to 0 problems consult a qualified technician 07 IGBT Consult a qualified temperature technician sensor error 09 Pan Consult a qualified temperature technician sensor error 10 Supplied Check the power supply lt 180V Consult a qualified technician N B When the electricity supply is restored after it has been cut off e g blackout the green indicator light flashes 5 times Turn the knob to 0 and switch the appliance on again 13 REPLACING COMPONENTS REMINDERS FOR REPLACING COMPONENTS e Disconnect the appliance from the electricity supply and unplug it before carrying out any procedure Replacing the filter Slide out the filter on the base of the appliance e Remove and replace the component e Re assemble all parts For assembly proceed in reverse order 14 CLEANING THE INTERIOR e Check the condition of the inside of the appliance e Remove any built up dirt
3. to clean the floor beneath the appliance 3 DISPOSAL OF PACKAGING AND THE APPLIANCE 3 1 PACKAGING The packaging is made using environmentally friendly materials The plastic recyclable components are e the transparent cover the bags containing the instructions manual and nozzles made of Polyethylene PE e the straps in Polypropylene PP 3 2 APPLIANCE The appliance is manufactured 90 from recyclable metals stainless steel aluminum sheet copper The appliance must be scrapped in compliance with current regulations governing such disposal e It must be disposed of properly e Make the appliance unusable before scrapping INSTRUCTIONS FOR INSTALLATION REMINDERS FOR THE INSTALLER The manufacturer will not be liable for any damage or injury resulting from failure to observe the following rules e Read this manual carefully It provides important information for safe installation use and maintenance of the appliance e Appliance maintenance must be carried out by qualified technicians authorized by the manufacturer in compliance with current safety standards and the instructions in this manual e Identify the specific appliance model The model number is detailed on the packaging and on the appliance data plate e The appliance must be installed in a well ventilated room e Do not obstruct any air vents or drains present on the appliance e Do not tamper with appliance components 4 REFERENCE STAN
4. which might scratch and damage the surfaces 10 FILTERS AIR FILTERS e Check and clean the air filter regularly e To clean the filter remove it from its slot if it is saturated with grease wash it with a grease removal soap then rinse and dry When the procedure is concluded refit the filter in its seat When the filter is deteriorated it must be renewed INSTRUCTIONS FOR MAINTENANCE REMINDERS FOR THE MAINTENANCE TECHNICIAN The manufacturer will not be liable for any damage or injury resulting from failure to observe the following rules e Read this manual carefully It provides important information for safe installation use and maintenance of the appliance e Appliance maintenance must be carried out by qualified technicians authorized by the manufacturer in compliance with current safety standards and the instructions in this manual e Identify the specific appliance model The model number is detailed on the packaging and on the appliance data plate e The appliance must be installed in a well ventilated room e Do not obstruct any air vents or drains present on the appliance e Do not tamper with appliance components e Check and clean the air filter regularly 11 COMMISSIONING Following installation conversion to a different type of gas or any maintenance operations check appliance operation In the event of any malfunction consult the next Paragraph Troubleshooting 11 1 ELECTRICAL APPLIANCES
5. DARDS AND LAWS Install the appliance in compliance with UNI 8723 safety standards and with D M n 74 of 12 04 1996 Install the appliance in compliance with the prescriptions of EN1717 and the water pollution regulations in force in your country 5 UNPACKING Check the state of the packaging and in the event of damage ask the delivery person to inspect the goods e Remove the packaging e Remove the protective film from the external panels Use a suitable solvent to remove any residual adhesive from the panels 6 POSITIONING e The overall dimensions of the appliance and the position of connections are given on the installation diagram at the start of this manual e The appliance can be installed independently e Position the appliance at least 10 cm from adjacent walls This distance can be reduced in the presence of non combustible walls or heat insulated walls 7 CONNECTIONS The position and dimensions of connections are given in the installation diagram at the start of this manual 7 1 ELECTRICAL CONNECTIONS Check that the appliance is designed to operate at the voltage and frequency of the power supply present on site Check the details given on the appliance data plate e At an easily accessible point upline of the appliance fit an all pole disconnect switch of suitable capacity with a contact breaking distance of at least 3 mm and a highly sensitive differential protection device The maximum permitted leakage
6. current is 1 mA kW e Insert the plug into the relevant socket 8 COMMISSIONING See Chapter INSTRUCTIONS FOR MAINTENANCE INSTRUCTIONS FOR USE REMINDERS FOR THE USER The manufacturer will not be liable for any damage or injury resulting from failure to observe the following rules e Read this manual carefully It provides important information for safe installation use and maintenance of the appliance e Keep this manual in a safe place known to all users so that it can be consulted throughout the working life of the appliance e Appliance maintenance must be carried out by qualified technicians authorized by the manufacturer in compliance with current safety standards and the instructions in this manual e For after sales service contact technical assistance centres authorized by the manufacturer and demand the use of original spare parts e Have the appliance serviced at least twice a year The manufacturer recommends taking out a service contract e The appliance is designed for professional use and must be operated by trained personnel e The appliance is to be used for cooking food as specified in the reminders for use Any other use must be considered improper e Do not allow the appliance to operate empty for prolonged periods e Do not leave the appliance unattended while in operation e If the appliance breaks down or malfunctions turn off the power supply main switch installed upline of the appliance and
7. er via a licenced waste handler Units are designed to be dismantled easily and recycling of all material is encouraged whenever practicable Falcon Foodservice Equipment HEAD OFFICE AND WORKS Wallace View Hillfoots Road Stirling FK9 5PY Scotland SERVICELINE CONTACT Phone 01438 363 000 Fax 01438 369 900 GENERAL INFORMATION This chapter contains general information which all users of the manual must be familiar with Specific information for individual users of the manual is provided in subsequent chapters INSTRUCTIONS FOR 1 APPLIANCE SPECIFICATIONS e The data plate is located at the bottom of the appliance e The appliance model and serial number are also detailed on decals under the brand logo and on the packaging 2 GENERAL PRESCRIPTIONS The manufacturer will not be liable for any damage or injury resulting from failure to observe the following rules REMINDERS FOR THE INSTALLER e Read this manual carefully It provides important information for safe installation use and maintenance of the appliance e Appliance maintenance must be carried out by qualified technicians authorized by the manufacturer in compliance with current safety standards and the instructions in this manual e Identify the specific appliance model The model number is detailed on the packaging and on the appliance data plate e The appliance must be installed in a well ventilated room e Do not obstruct any air vents or dra
8. iTOP Induction Unit INSTALLATION SERVICING EG and USER INSTRUCTIONS IMPORTANT The installer must ensure that the installation of the appliance is in conformity with these instructions and National Regulations in force at the time of installation Particular attention MUST be paid to BS7671 IEE Wiring Regulations Electricity at Work Regulations Health And Safety At Work Act Fire Precautions Act This appliance has been CE marked on the basis of compliance with the Low Voltage and EMC directives for the voltages stated on the data plate WARNING THIS APPLIANCE MUST BE EARTHED On completion of the installation these instructions should be left with the Engineer in Charge for reference during servicing A demonstration of operation and cleaning should be given to users IT IS MOST IMPORTANT THAT THESE INSTRUCTIONS BE CONSULTED BEFORE INSTALLING AND COMMISSIONING THIS APPLIANCE FAILURE TO COMPLY WITH THE SPECIFIED PROCEDURES MAY RESULT IN DAMAGE OR THE NEED FOR A SERVICE CALL PREVENTATIVE MAINTENANCE CONTRACT In order to obtain maximum performance from this unit we would recommend that a Maintenance Contract be arranged with SERVICELINE Visits may then be made at agreed intervals to carry out adjustments and repairs A quotation will be given upon request to the SERVICELINE contact numbers below WEEE Directive Registration No WEE DC0059TT PRO At end of unit life dispose of appliance and any replacement parts in a safe mann
9. ins present on the appliance e Do not tamper with appliance components REMINDERS FOR THE USER e Read this manual carefully It provides important information for safe installation use and maintenance of the appliance e Keep this manual in a safe place known to all users so that it can be consulted throughout the working life of the appliance e Appliance installation and maintenance must be carried out by qualified technicians authorized by the manufacturer in compliance with current safety standards and the instructions in this manual e For after sales service contact technical assistance centres authorized by the manufacturer and demand the use of original spare parts e Have the appliance serviced at least twice a year The manufacturer recommends taking out a service contract e The appliance is designed for professional use and must be operated by trained personnel e The appliance is to be used for cooking food as specified in the reminders for use Any other use must be considered improper e Do not allow the appliance to operate empty for prolonged periods e Do not leave the appliance unattended while in operation e If the appliance breaks down or malfunctions turn off the power supply main switch installed upline of the appliance and pull the plug out of the socket e Clean the appliance following the instructions given in Chapter INSTRUCTIONS FOR CLEANING e Do not store flammable materials in close p
10. nged disuse of the appliance proceed as follows e Clean the appliance thoroughly e Rub stainless steel surfaces with a cloth soaked in Vaseline oil to create a protective film e Shut off the main switch upline of the appliance or pull the plug out of the socket Following prolonged disuse proceed as follows e Inspect the appliance thoroughly before using it again e Allow electric appliances to operate at the lowest temperature for at least 60 minutes INSTRUCTIONS FOR CLEANING REMINDERS FOR CLEANING The manufacturer will not be liable for any damage or injury resulting from failure to observe the following rules e Disconnect the appliance from the electricity supply and unplug it before carrying out any procedure e Clean the satin finish stainless steel exterior surfaces the cooking wells and the surface of the hotplates every day e At least twice a year have an authorized technician clean the internal parts of the appliance e Do not use direct or high pressure water jets to clean the appliance e Do not use corrosive products to clean the floor beneath the appliance SATIN FINISH STAINLESS STEEL SURFACES e Clean the surfaces with a cloth or sponge using water and proprietary non abrasive detergents Follow the direction of the satin finish lines Rinse repeatedly and dry thoroughly e Do not use pan scourers or other iron items e Do not use chemical products containing chlorine e Do not use sharp objects
11. ocked and not obstructed very efficient ambient check that the air temperature temperature is under too high with 40 C 110 F Switch insufficient off the appliance and airflow for contact a qualified cooling technician authorized appliance by the manufacturer breakdown The control Knob Switch off the knob is not damaged appliance and working contact the after sales support service Heating is The airflow Check unblock the inconsistent has been ducts switch off the and the interrupted appliance and clean fan operates the fan is the fan continuously jammed Heating is Fan short Switch off the inconsistent circuited appliance and and the fan contact the after is not working sales support service Heating is Cooking zone Switch off the appliance remove the pan and wait for the zone to cool down If the green indicator light is off e Power supply main switch disconnected e Insufficient voltage or incorrect electric connection of the appliance If the green indicator light is on e Check and count the green indicator light flashes This number is the code of the malfunction message detailed in the following table ERROR MESSAGE CAUSE 01 No power at _ No pan cookware inductor used incorrectly consult a qualified technician 03 Overheating Cooling required switching off consult a qualified technician 04 High Clean the fan check temperature _ its rotation
12. oking foods contained in pots and pans e Use flat bottomed pans Use a special wok pan on the wok hotplate e Do not leave the hotplates switched on with no pan or an empty pan in place e Do not pour cold liquids onto the hot hotplate e The induction hob made of glass ceramic is ready for use no pre heating is required e Do not use multi layered pots with aluminium core open along the edge e The induction heating system will not function with unsuitable materials These are chrome nickel stainless steel aluminium copper brass glass stoneware e Pots with a diameter smaller than approx 12cm are not detected by the system and the appliance will therefore not switch on e Use pots with a maximum diameter of 24cm for maximum heating efficiency e Do not leave the hotplates switched on with no pan or an empty pan in place e Take care when moving pots on the hob Dropping items on the glass ceramic hob may cause irreparable damage e Position the pan in the middle of the cooking zone e We recommend the use of pans designed specifically for induction cooking Be wary of very cheap models e The product should be operated well away from sources of heat such as gas or halogen appliances SWITCHING ON AND OFF The glass hob knob has the following positions 0 Off MAX Max temperature Switching off e Turn the thermostat control knob to position 0 indicator light off 9 PROLONGED DISUSE Before any prolo
13. pull the plug out of the socket e Clean the appliance following the instructions given in Chapter INSTRUCTIONS FOR CLEANING e Do not store flammable materials in close proximity to the appliance FIRE HAZARD e Children must be supervised to ensure that they do not play with the appliance e The appliance is not destined for use by persons including children with reduced physical sensory or mental capacities or who have no experience or knowledge unless they are supervised or trained in the use of the machine by a person responsible for their safety e Do not obstruct any air vents or drains present on the appliance e Do not tamper with appliance components e Do not use the appliance without the filters e Under no circumstances should the induction cooker be switched on if the glass ceramic hob is cracked or broken This could be dangerous e With the transmission of heat from pots the glass ceramic hob becomes extremely hot and must therefore never be touched after cooking risk of burns e Do not place metal items equipment knives etc near the cooking zones as they can become hot very quickly e During use take care when wearing rings watches and similar items since these can become extremely hot if too close to the cooking zone e Users must be informed of the potential risks for individuals fitted with a heart pacemaker or metallic prosthesis USE REMINDERS FOR USE e The appliance is designed for co
14. roximity to the appliance FIRE HAZARD e Children must be supervised to ensure that they do not play with the appliance e The appliance is not destined for use by persons including children with reduced physical sensory or mental capacities or who have no experience or knowledge unless they are supervised or trained in the use of the machine by a person responsible for their safety e Do not obstruct any air vents or drains present on the appliance e Do not tamper with appliance components REMINDERS FOR THE MAINTENANCE TECHNICIAN e Read this manual carefully It provides important information for safe installation use and maintenance of the appliance e Appliance maintenance must be carried out by qualified technicians authorized by the manufacturer in compliance with current safety standards and the instructions in this manual e Identify the specific appliance model The model number is detailed on the packaging and on the appliance data plate e The appliance must be installed in a well ventilated room e Do not obstruct any air vents or drains present on the appliance e Do not tamper with appliance components REMINDERS FOR CLEANING e Clean the satin finish stainless steel outer surfaces on a daily basis At least twice a year have an authorized technician clean the internal parts of the appliance e Do not use direct or high pressure water jets to clean the appliance e Do not use corrosive products
Download Pdf Manuals
Related Search