ALPINE 6600 STRINGING MACHINE USER`S MANUAL
Contents
1. pressing the clamp jaws together to open the foot 7 Insert the side supports onto the hole of the side support arms Select big jaw open for tennis and small jaw open for badminton racquet frames Adjust the width of the mounting arms to the size of the racquet frames Side Support 3 Mounting The Tennis Racquet Frame 1 Place the center of the racquet frame properly on the top of both mounting stocks and make the center supports match the center point of the racquet frame Adjust the vise to accommodate various size racquet frames and lock into position with Allen Wrench Check that the two string clamps can reach all the stringing area of the racquet frame 3 Lightly tighten center supports by turning the knobs on the outside of the center support clockwise 3 Rotate the side support arm adjustment knobs clockwise until the firm contact is made between the side supports and the racquet frame If the side supports can t contact the frame squarely when the arms are closed against the racquet please insert the side supports onto the other holes of the side support arms Apply a final adjustment to all racquet support points until the racquet is firmly secured in the mounting system 4 KEYPAD OPERATING INSTRUCTIONS Step 1 Battery Setting Set one dry battery 9 volts beneath the tension head Caution position and correctly E Step 2 Power Button To turn the machine on press the2. ALPINE 6600 STRINGING MACHINE USER S MANUAL 1 ANATOMY Ser Der NA A pr Dun js 10 top of the throat mounting stock OV NY N IN WN N N DN NHN e e a a a Pp PL m CONN tA Ek O IN O O 0 J HW 4 RK L N e machine body floor stand height adjustment brake tool tray string reel holder column H base foot rubber cover center support adjustment knob bottom of the throat mounting stock head mounting stock upper tray table side support gliding clamp glide bar String gripper tension locking lever display power button tension setting knob tension head handle crank tension head cover housing Stopper tension head rail side support arm adjustment knob center support 2 ASSEMBLY INSTRUCTIONS Your machine is shipped one carton and comes in four parts base column tool tray machine body and accessory bag Remove all parts from the shipping carton 1 Assemble the column to thefl shaped base with 4 Allen Head screws by 6mm T shaped Wrench and 12 10 mm Wrench 2 Screw the reel holder into the column I gt 3 Mount the tool tray on the 4 Insert the machine body into column by fastening with column top and allow to set four 6 mm screws a ne NA M fi Ne 5 Adjust the machine body to the desired height and lock into position with height adjustment 6 Attach the clamps to each of the glide bars by lifting the clamp lever up and
3. black POWER KG LB button for 1 second until a tension appears on the display NOTE the power save function has been set for 1 minute at factory before shipping so the display will shut down automatically after 1 minute To motivate the display repeat the procedure step 2 again To turn power off press the black POWER KG LB button for 2 seconds until OFF appears on the display Or wait for 1 minute till the power save function is motivated and display will shut down automatically as well Step 3 KG LB Button Press the black POWER KG LB button for 0 5 second to change tension display from KG to LB To set tension unit from LB to KG press the black POWER KG LB button for 0 5 second again 5 TENSIONING Step 1 Setting Tension Set the tension by rotating the tension setting knob counter clockwise to increase the tension or clockwise to decrease the tension until the desired tension appears on the display Step 2 Pulling the Strings To pull the string continue rotating the tension head crank handle backward until the tension locking lever clicks out This locks the tension head to the tension rail Step 3 Releasing the Strings To release the string after clamping hold on to tension head and push tension locking lever back up into the catch on the tension head Lift the string out of the string gripper for the next hole 6 TENSION CALIBRATION Step 1 Set the tension scale on 60 Ibs Place a s
4. tring attached to a tension calibrator in string gripper Tension calibrator will indicate the pounds of tension on tension head under actual stringing conditions Pull string until the locking lever releases If it releases before 60 Ibs or after 60 Ibs the following adjustment is needed CAUTIION Be sure to release string holding tension calibrator You are now ready for adjustment Step 2 Loosen the safety screw A If the locking lever release before 60 lbs turn the adjustment screw B counterclockwise until the scale reading matches the calibrator s if the locking lever release after 60 Ibs turn the adjustment screw B clockwise WARNING Be sure to tighten the safety screw A after the adjustment has been made
Download Pdf Manuals
Related Search