eMT-3000 Series
Contents
1. NOTE 1 Connect positive DC line to the terminal and the DC ground to the terminal 2 Please do not connect HMI with PLC and PC simultaneously to prevent potential difference from destroying USB ports of HMI and PC 33353338 3 unpacking the Unit NOTE 000000007 Place the operator panel on a stable eeeceeeee I 24V DC Unpack and check the delivery If damage is found surface during installation Dropping it or notify the supplier letting it fall may cause damage i AEE 3 system Settings When HMI is powered up and displays image Go to the Network tab you may choose 1 Installation Instruction 2 sided A4 1 click the system setting button to auto get DHCP IP or designate your Default System Password 111111 own IP It is necessary to connect the HMI to 2 Human Machine Interface 1 your network through a RJ 45 cable Network Time Date Secunty History Backlight CF card 3 Power Connector 1 a E IP address get from below IP Address 192 168 1 201 Subnet Mask 255 2255 255 0 4 Brackets amp Screws 1 pack ene ey remy ema pe 5 Fuse 1 6A 250V 5 20mm 1 1 25A for 3070 Note 1 For the details of HMI DIP SW function settings please refer to Part 8 in this guide Apply Q EasyBuilder Pro Software Settings Launch EasyBuilder Pro software select your project file press F7 shortcut key to open the download dialog box Select Ethernet gt IP tab gt Ente2. application the following precautions generally apply to installation of solid state programmable control devices and conform to the guidelines for installation of Controllers recommended in NEMA ICS 3 304 Control Standards To conform with ICS Safety Recommendations checks should be placed in the controller to ensure that all writable registers that control critical parts of plant or machinery have limit checks built into the program with an out of limit safe shut down procedure to ensure safety of personnel Limited Warranty This product is limited warranted against defects in desi ign and manufacture The proven defective product will either be repaired or replaced at Weintek s discretion This warranty shall not cover any product which is Programming Considerations a Out of warranty period which is 12 months from the manufacturing month of the HMI products o Damage caused by Force Majeure accident negligence improper installation or misuse c Product has been repaired or taken apart by unauthorized technicians d Products whose identification markings have been removed or damaged
3. eMT 3000 Series installation Instructions Secure the control panel in position using all the fastening holes and the provided brackets Installation Instruction and screws A installation and Startup Guide This document covers the installation of eMT 3000 Series HMI for the detailed specifications and operation please refer to Brochure and EasyBuilder Pro User Manual Install Environment eMT3070A B NEMA Rating The eMT 3000 Series HMI is NEMA 4 rated eMT3105P 259 201 201 eMT3120A 305 eMT3150A 352 Environment This does not guarantee noise immunity in severe cases Proper wire routing and grounding will insure proper operation Make sure that the displays are installed correctly and that the operating ppower Connections limits are followed Avoid installing units in environments where severe mechanical vibration or shocks are present Do not operate the unit in areas subject to explosion hazards due to Environmental flammable gases vapors or dusts Considerations Do not install the unit where acid gas such as SO2 exists This device should be mounted in the vertical position and for use on the flat surface enclosure Conform to UL508 ISBN 0 7629 0404 6 machine safety for use in Pollution Degree 2 Environment Nom The eMT 3000 Series has been tested to conform to European CE requirements Electrical This means that the circuitry is designed to resist the effects of electrical noise
4. on mode To enter touch screen calibration mode press and hold anywhere on the screen for more than 2 seconds when HMI starts After all the calibration points have been To LEET a pop up window is displayed and begins countdown from 10 seconds If the user clicks the OK button within 10 seconds the calibration data will be saved to the system otherwise the calibration will restart During the 10 second countdown the user can touch the screen to check the calibration result Press OK to save result NOTE Make sure that all local and national electrical standards are met when installing the unit Contact your local authorities to determine which codes apply CAUTION The HMI can be powered by DC power only voltage range 24 20 Volts DC compatible with ZN Power most controller DC systems The power conditioning circuitry inside the unit is accomplished by a switching power supply The peak starting current can be as high as 2A If the display does not come on within 5 seconds of power up remove power An internal fuse will Fusin AN Require prevent damage if the polarity of the DC power is incorrect Check wiring for proper connections ments and try to power up again Hiah An Internal fuse will prevent damage for overcurrent condition however it isn t guaranteed DC g voltage sources should provide proper isolation from main AC power and similar hazards Voltage Emergency A Hard wired EMERGENCY STOP should be fitted in any s
5. r your HMI IP gt Click Download to download this project file to HMI Please refer to EasyBuilder Pro User Manual for software operation details J Font fies J Femware Necessary f update firmware or execute download first time Use user defined startup screen Reset reape Reset recipe database Yi Reset event log v Reset data sampling Reboot HMI after download Autornatically using current settings to download after compiling Communication Connections NOTE 1 COM1 RS232 RTS CTS amp COM3 RS232 can t be used simultaneously 2 COM1 and COMBS RS485 support MPI 187 5K please use one at one time 3 COM1 RS485 COM3 RS485 CAN Bus with isolation protection COM1 COM3 RS232 9 Pin Male D sub COM1 COM3 RS485 CAN Bus 9 Pin Female D sub 12345 54321 6789 9876 COM1 COMS3 Com1 RS485 Com3 CAN PIN Symbol RS232 RS232 PIN Symbol RS485 Not used Data Received 2 RxD Data 3 Ro Data Ro Transmitted X X 3 TxD Data 4 Tx TX 4 Mousse 5 GND Ground 5 GND Ground 6 Data Data 6 Not used l 7 CAN L CAN_L 7 RTS Ready to Transmitted send output Data 8 CAN_H CAN_H Clear to Received D D 8 CTS send input Data 2 stat ates 9 Not used DIP sw settings TN swi_ sw2_ sw3_ sw4 Mode ON OFF OFF OFF Touch Screen Calibration Mode E E E E OFF ON OFF OFF Hide HMI System Setting Bar 1234 OFF ORE ON OF Boot Loader Mode OFF OFF OFF ON Reserved OFF ORF OFF OFF Normal calibrati
6. ystem using a HMI to comply with ICS A Stop Safety Recommendations Supply Do not power the HMI and inductive DC loads or input circuitry to the controller with the same AN Voltage power supply Note The 24 VDC output from some controllers may not have enough current to Condition power the HMI Wire a Power wire length should be minimized Max 500m shielded 300m unshielded 1 Routing b Please use twisted pair cables for power wire and signal wire and conform to the impedance matching If wiring is to be exposed to lightning or surges use appropriate surge suppression devices d Keep AC high energy and rapidly switching DC power wiring separated from signal wires Add a resistor and capacitor in the parallel connection between the ungrounded DC power supply and the frame ground This provides a path for static and high frequency dissipation DANGER Typical values to use are 1M Ohm and 4700pF Hardware Considerations O D The system designer should be aware that devices in Controller systems could fail and thereby create an unsafe condition Furthermore electrical interference in an operator interface can lead to equipment start up which could result in property damage and or physical injury to the operator If you use any programmable control systems that require an operator be aware that this potential safety hazard exists and take appropriate precautions Although the specific design steps depend on your particular
Download Pdf Manuals
Related Search