User Manual
Contents
1. give an automatic sound activated ene ae show This function is good when you J and select Sh Ovenins show ah li show 1 or or show 12 and speed Its DMX input jack will have nothing plugged into it and Its master LED will be constantly on and sound LED will flash to the music The other units will have to select normal or DL E 2 light show mode Their DMX cables plugged into the DMX input jacks daisy chain and the slave led lights will constantly on 2 light show In slave mode means the unit works as the master unit and means 2 light show In order to create a great light show you can set on the second unit to get contrast movement to each other even if you have two units only 4 2 Easy Controller by CA 8 The easy remote control is used only in master slave mode There is a terminator for connect the easy controller inside the fixture By connecting the cable into DMX IN waterproof cable entry gland to the CA 8 terminator of the first fixture you will find that the remote control on the first fixture will control all the other fixtures for Stand by Function and Mode functions Blackout Blackout the unit 1 Sound White Strobe Select Show 2 Sound Color Strobe Show 1 12 Sound Strobe Show i PES LED OFF LED ON Con ntroiter J j Function To select any functions press MENU button until the required one is shown on the display Select the functi2. MENU button again If you use please refer to the following diagram to address your DMX512 channel for the first 4 2 units EERE PL SLOS 256 channels I1 25 1 channel 4 channels 5 DMX512 Configuration 1 amp 4 CH modes DMA512 Configuration Ooo m o Pattern Chase Chase u a CH1 10 99 CH1 100 239 cHe oi 99 CH1 100 239 strobe 239 255 R G B W 955 236 255 Pattern 12 236 255 Chase 12 999 238 G B W Fast 194 214 Pattern 10 194 214 Chase 10 188 204 R G W Chase 4 Chase 3 Chase 2 Chase 1 OFF 100 239 Pattern 173 193 Pattern 9 151 172 Patterns 130 150 Pattern 7 109 129 Pattern 6 088 108 Pattern 5 066 087 Pattern 4 042 065 Pattern 3 021 041 Pattern 2 000 020 Pattern 1 173 193 Chase 9 151 172 Chase 8 130 150 Chase 7 109 129 Chase 6 088 108 Chase 5 066 087 Chase 4 042 065 Chase 3 021 041 Chase 2 000 020 Chase 1 171 187 R G B 154 170 B W 137 153 G W 10 255 120 136 G B 103 119 R W 086 102 R B 069 085 R G 052 068 W 035 051 B 018 034 G 000 017 R 3 By DMX controller No need to turn the unit off when you change the DMX address as new DMX address setting will be effected at once Every time you turn the unit on it will show 7871 on the display After that the unit will be ready to receive DMX signal or run the built in programs 4 1 Master Slave Built In Preprogrammed Function By linking the units in master slave connection the first unit will control the other units to
3. press ENTER button to setup or automatically exit menu mode without any change after 10 seconds To go back to the functions without any change press the MENU button LED display Press the MENU button up to when the Led is shown on the display Pressing ENTER button and the display will blink Use DOWN and UP button to select display on or oF Fldisplay off mode Once select press ENTER button to setup or exit menu mode without any change after 10 seconds Back to the functions without any change press MENU button again Cid Display Inverse j i di SF Press MENU button until di SA ats blinking on the display Use DOWN and UP buiton to select lot SPI normal or inverse press ENTER button to setup Back to the functions without any change press MENU button tt os t E 3c Self Test Press the MENU button up to when the test is blinking on the display Pressing ENTER button and the unit will run the built in programmer for self test To go back to the functions press the MENU button maia 5 Fixture Hours Press the MENU button up to when the rhe is blinking on the display Pressing ENTER button and the display will show the number of working hours of the unit To go back to the functions press the MENU button a Lil Software version Press the MENU button up to when the Ler is blinking on the display Pressing ENTER button and the display will show the version of software of the unit To go b
4. 00 255r 100 255r 100 255r 100 rotating effects e Great built in lighting shows under Master Slave operation triggered by music e Optional CA 8 easy controller for enjoying instant lighting shows at you fingertips e LED display for easy navigation e Input Voltage 100V 240V 50 60Hz e Power consumption 29W e LED Total 256pcs Red 64pcs Green 64pcs Blue 64pcs White 64pcs e Dimension 270 x 242 x 317mm e Weight 3 8 kgs 6 DMX512 Connections The DMX512 is widely used in intelligent lighting control with a maximum of 512 channels 4 channels as a group please refer to the DMX configuration of 1 4 channels to control the other channels when you choose 256 channels mode Under this mode you can control the 256 LEDs separately ij hi ij f wj DMX INPUT 3 p NN a E DMX OUTPUT C i if Nee al i af Termination reduces signal errors and to avoid signal we transmission problems and interference It is always G advisable to connect a DMX terminal aa Resistance 120 ohm 1 4W between pin2 DMX and pin3 DMX of the last fixture 1 Connect the fixture together in a daisy chain by XLR plug cable from the output of the fixture to the input of the next fixture The cable cannot be branched or split to a Y cable Inadequate or damaged cables soldered joints or corroded connectors can easily distort the signal and shut down the system 11 4 3 How To Set The Fixture 3 1 Contro
5. Innovation Quality Performance 15 MATRIX LED LINKABLE a b Mary ares Ld asin E t STAND ALONE i LED 7871 User Manual Please read the instructions carefully before use EC Declaration of Conformity We declare that our products lighting equipments comply with the following specification and bears CE mark in accordance with the provision of the Electromagnetic Compatibility EMC Directive 89 336 EEC EN55014 2 1997 A1 2001 EN61000 4 2 1995 EN61000 4 3 2002 EN61000 4 4 1995 EN61000 4 5 1995 EN61000 4 6 1996 EN61000 4 11 1994 amp Harmonized Standard EN60598 1 2000 ALL 2000 A12 2002 Safety of household and similar electrical appliances Part 1 General requirements master slave mode signal 2 Wrong DMX address in the fixture Set the proper address D No response to the sound 1 Make sure the fixture does not receive DMX signal 2 Check microphone to see if it is good by tapping the microphone E One of the channels is not working well 1 The stepper motor might be damaged or the cable connected to the PCB is broken 2 The motor s drive IC on the PCB might be out of condition 8 Fixture Cleaning The cleaning of internal must be carried out periodically to optimize light output Cleaning frequency depends on the environment in which the fixture operates damp smoky or particularly dirty surrounding can cause greater accumulation of dirt on the fixture s opt
6. Pin 2 Negative signal Pin 3 Positive signal 5 pin XLR Pin 1 GND Pin 2 Negative signal Pin 3 Positive signal Pin4 5 not used 7 Troubleshootino Following are a few common problems that may occur during operation Here are some suggestions for easy troubleshooting A The fixture does not work no light 1 Check the connection of power and main fuse 2 Measure the mains voltage on the main connector U Not responding to DMX controller 1 DMX LED should be on If not check DMX connectors cables to see if link properly 2 Ifthe DMX LED is on and no response to the channel check the address settings and DMX polarity 3 If you have intermittent DMX signal problems check the pins on connectors or on PCB of the fixture or the previous one 4 Try to use another DMX controller 5 Check if the DMX cables run near or run alongside to high voltage cables that may cause damage or interference to DMX interface circuit O Some fixtures don t respond to the easy controller 1 You may have a break in the DMX cabling Check the LED for the response of the 12 256 CH mode 2 technical Specifications DMX512 Configuration l Ch253 Ch254 e The Matrix 4 LED features 4 high brightness red green blue and white LEDs clusters Blue white Red Green Blue White cresting stunning text patterns geometric figures dynamic scanning rolling and 255r 100 255r100 255r 100 255r 1
7. ack to the functions press the MENU button again 4 How To Control The Fixture You can operate the unit in three ways 1 By master slave built in preprogram function 2 By easy controller
8. e Do not touch any wire during operation and there might be a hazard of electric shock e To prevent or reduce the risk of electrical shock or fire do not expose the fixture to rain or moisture e The housing must be replaced if they are visibly damaged e Do not look directly at the LED light beam while the fixture is on e There are no user serviceable parts inside the fixture Do not open the housing or attempt any repairs by yourself In the unlikely event your fixture may require service please contact your nearest dealer e Due to the magnifying type lens please keep the lens out of contact with direct sunlight Direct sunlight can cause heat to build up inside of the unit which will seriously damage unit For power supply do not connect in series much more than 20 units use another mains supply for next 20 units 2 The DMX output and input connectors are pass through to maintain the DMX circuit when one of the units power is disconnected 3 At last fixture the DMX cable has to be terminated with a terminator to reduce signal errors Solder a 120 ohm 1 4W resistor between pin 2 DMX and pin 3 DMX into a 3 pin XLR plug and plug it in the DMX output of the last fixture 4 Each lighting fixture needs to have an address set to receive the data sent by the controller The address number is between 0 511 usually O amp 1 are equal to 1 5 3 pin XLR connectors are more popular than 5 pins XLR 3 pin XLR Pin 1 GND
9. ics e Clean with soft cloth using normal glass cleaning fluid e Always dry the parts carefully e Clean the external optics at least every 20 days Clean the internal optics at least every 30 60 days 13 TABLE OF CONTENTS 1 Safety Instructions 2 Technical Specifications 3 How To Set The Fixture 4 How To Control The Fixture 5 DMX 512 Configuration 6 DMX 512 Connections 7 Troubleshooting 8 Fixture Cleaning Introductions A N Please read the instructions carefully which includes important information about the installation operation and maintenance WARNING e Please keep this User Manual for future consultation If you sell the fixture to another user be sure that they also receive this instruction booklet e Unpack and check carefully there is no transportation damage before using the fixture e ts important to ground the yellow green conductor to earth in order to avoid electric shock e Disconnect main power before servicing and maintenance e Maximum ambient temperature is Ta 40 C Don t operate it where the temperature is higher than this e Inthe event of serious operating problem stop using the fixture immediately Never try to repair the fixture by yourself Repairs carried out by unskilled people can lead to damage or malfunction Please contact the nearest authorized technical assistance center Always use the same type spare parts e Do not connect the device to any dimmer pack
10. l Panel 1 Display To show the various menus and the selected functions LED 83 MASTER_ On Master Mode 4 SLAVE On Slave Mode 5 SOUND Flashing Sound activation Button 6 MENU T DOWN To select the programming functions To go backward in the selected functions Q ENTER UP To go forward in the selected functions To confirm the selected functions T Sensitivity Adjust sensitivity of the sound control o Microphone Receive music for the sound active Q Only for remote control By connect to the 1 4 microphone jack to control the unit for Stand by Function and Mode function E DMX output For DMX512 link use 3 pin XLR plug cable to link the next unit q4 DMX input For DMX512 link use 3 5 pin XLR plug cable to input DMX signal 5 Mains output Connect to supply mains power for the next unit Mains input Connect to supply mains power 5 4 3 DMX Controller Using universal DMX controller to control the units you have to set DMX address from 1 to 512 channel so that the units can receive DMX signal Press the MENU button up to when the AJAT js showing on the display Pressing ENTER button and the display will blink Use DOWN and UP button to change the DMX512 address Once the address has been selected press and keep ENTER button pressed up to when the display stops blinking or storing automatically 8 seconds later To go back to the functions without any change press the
11. on by ENTER button and the display will blink Use DOWN and UP button to change the mode Once the required mode has been selected press ENTER button to setup or it will automatically return to the main functions without any change after idling 10 seconds Back to the functions without any change press MENU button The main functions are shown below im gi RSE eT Cii i SL 2 MENU op nE Channel mode Master Mode Slave Mode Normal slave mode 2 Light Show Random Show show mode 1 12 Sound Mode on Sound Mode off Blackout Mode Yes Blackout Blackout Mode No Blackout LED on LED off Normal Inversion k por Self Test FHS Fixture Hours Software Version DMX 512 Address Setting Press the MENU button up to when the Addl is shown on the display Pressing ENTER button and the display will blink Use DOWN and UP button to change the DMX 512 address Once the address has been selected press ENTER button to setup or automatically exit menu mode without any change after 10 seconds Back to the previous functions without any change press MENU button C Mi i d Channel Mode Press the MENU button up to when the LANO is shown on the display Pressing ENTER 6 one cal the display will blink Use DOWN and UP button to select the Lal 1 channel or my 4 channels or ERRA 256 Channels mode Once the mode has been selected press the ENTER button to setup or automatically exi
12. t menu mode without any change after 10 seconds To go back to the functions without any change press the MENU button cin fits Slave Mode Press the MENU button up to when the Sind is shown on the display Pressing ENTER button Use DOWN and UP button to select the ASE master or Gi i slave 1 or Gi ol Slave 2 mode Once select press the ENTER button to setup or automatically exit menu mode without any change after 10 seconds To go back to the functions without any change press the MENU button INi Mi id Show Mode Press the MENU button up to when the SAd is shown on the display Pressing ENTER button Use DOWN and UP button to select the Sh i Random show or Gh show 1 or Sh ol Show 2 or or Sh te show 12 Once select press ENTER button to setup or automatically exit menu mode without any change after 10 seconds To go back to the functions without any change press the MENU button Sound Press the MENU button up to when the is shown on the display Pressing ENTER button Use DOWN and UP button to select the sound on or sound off Once select press ENTER button to setup or automatically exit menu mode without any change after 10 seconds To go back to the functions without any change press the MENU button rr al i Blackout mode Press the MENU button up to when the bind is shown on the display Pressing ENTER button Use DOWN and UP button to select the HES blackout o normal Once select
Download Pdf Manuals
Related Search