EZ LOCK User Manual 230kb pdf
Contents
1. Contents AL MI EZ LOCK 1 x Security Torx Key Manual and and Back Plate 4 x Screws and raw plugs Marking out template ge mane Equipment required for controlling one door 12 volt DC power supply 2 amp minimum EV BPS Lock Magnetic EVML 250 Yale type keep 12 volt lock enter D Push to exit button EVEXIT Green break glass emergency release EVEBG Note for use with Magnetic lock only Functions of the EZ LOCK The EZ LOCK can control up to two doors by use of pin numbers Selectable Pin number length 2 3 4 5 and 6 digits per zone Programmable door open time 00 to 99 seconds Two locations zone 1 zone 2 are available for programming pin numbers 1000 Pins can be programmed for zone 1 10 Pins can be programmed for zone 2 Two volt free change over relays one per door Door closed function contact required 2 push to exit button inputs one per zone Programmable volt free change over relay for door bell function Programmable rear tamper Internal buzzer for tamper monitoring automatic cut off after 1 minute Sighting Of The EZ LOCK Site the EZ LOCK within easy access to the door doors to be controlled Recommended mounting height 1 2m Fitting Using the template mark and drill the fixing and cable entry holes Remove security screw from the underside of the keypad and remove back plate Fit and secure the back plate in its final position See Fig 1 Feed the cable from the keypad though the centr2. LED will start to flash Press the 0 key followed by the 2 key The rear tamer is now on How to Enable the door Bell function Note If two doors are being controlled the bell function can not be used Enter programming mode A Long bleep will be heard and the green power LED will turn orange Press the key followed by the 2 key the orange LED will start to flash Press the 0 key followed by the 2 key The door bell function is now on How to Disable the door Bell function Enter programming mode A Long bleep will be heard and the green power LED will turn orange Press the key followed by the 2 key the orange LED will start to flash Press the 0 key followed by the 1 key The door bell function is now off How to reset a lost programming pin number Note this will set the programming Pin back to its default factory setting of 1234 and leave all other settings intact Remove power to the keypad reader for 10 seconds Apply power and press the key within 3 seconds Technical Specification DC input 12 24volts AC input 12 24volts Standby current 80ma Operating current without lock 110ma Working temperature 20c to 50c IP rating 65 Dimension 152 x 45 x 25mm Technical Support 01527 515145 Elite Security Products Telephone 01527 515150 Unit 7 Target Park Shawbank Rd Technical Support 01527 515145 Lakeside Redditch B98 8YN email info espuk com
3. e hole of the back plate Clip the top of keypad onto the back plate and secure using the security fixing screw located on the underside of the keypad Make all wiring connections and connect 12 volts DC to the keypad The green power LED will now be illuminated on the front of the keypad Screw Taw plugs System wiring 1 aS Torx Screw Fig 1 Wiring Diagram and connections na Red power DC input 12V 24V Black power J AC input 12V 24V Brown door status detecting Orange push to exit button 1 Yellow push to exit button 2 Green GND A Blue NO 2 Purple COM 2 TE nce Gray NC 2 o No3 White NO 1 Pink COM 1 r E nc1 Aqua NC 1 Black white 485 Not Brown white 485 Shielded ground Red O DC input 12V 24V Black oJ AC input 12V 24V Prawn Door contact Orange So Button Aow 9 Button2 Green _ GND Ly UA Blue NO2 Door Additional power L Purple COM2 He be supply fie va 05D390K c Pink COM 1 cy H HS Door lock Black White 485 Brown White 485 Shielded ground 4 Brief details of programming Access To programming mode Selecting the length of the pin number to be used 2 3 4 5 and 6 digits Programme pin numbers There are two locatio
4. eard and the green power LED will turn orange Press the key then the 5 key the power LED will start to flash Enter the time in seconds for the unlock time from 00 to 99 seconds How to Change the Programming Pin Number Enter programming mode A Long bleep will be heard and the green power LED will turn orange Press key followed by the 3 key the orange LED will start to flash Enter the new programming pin twice A conformation bleep will be heard How to delete all pin numbers Enter programming mode A Long bleep will be heard and the green power LED will turn orange Press key followed by the 8 key the orange LED will start to flash Press the 8 key twice 7 conformation bleeps will sound How to load factory default settings Enter programming mode A Long bleep will be heard and the green power LED will turn orange Press the key followed by the 8 key the orange LED will start to flash Press the 9 key twice One bleep will sound and the System will automatically come out of programming mode How to Disable the rear tamper Enter programming mode A Long bleep will be heard and the green power LED will turn orange Press the key followed by the 6 key the orange LED will start to flash Press the O key followed by the 1 key The rear tamer is now off How to Enable the rear tamper Enter programming mode A Long bleep will be heard and the green power LED will turn orange Press the key followed by the 6 key the orange
5. ns for entering pin numbers zone 1 and zone 2 Zone 1 has 1000 locations available 000 999 Zone 2 has 10 locations available 00 09 Select the lock release times 00 99 seconds zone 1 and zone 2 How to escape programming mode Note if no keys are pressed for 30 seconds the unit will drop out of programming mode automatically How to enter and exit programme mode To enter programme mode enter the 4 digit pin number twice default pin 1234 To exit programme mode press the key How to set the length of the pin numbers to be used Enter programming mode by entering the 4 digit pin number twice default pin 1234 A Long bleep will be heard and the green power LED will turn orange Press the key followed by the 9 key the orange LED will now flash Press 04 a long bleep will be heard Enter the length of the pin number you require 2 3 4 5 or 6 If the length is the same as already programmed you will get a conformation bleep If you have changed the length you will get 7 bleeps to say it has now been changed Note Any pin numbers programmed into the system will be deleted if the pin length is change Zone 1 programming Programming a User Pin number to Zone 1 Note Zone 1 has 1000 locations available from 000 to 999 Enter programming mode A Long bleep will be heard and the green power LED will turn orange Enter the vacant location you want to programme the pin number in use a 3 digit format xxx The green prog
6. ramming LED top left of keypad will illuminate Note if this location already has a pin number programmed the LED will turn red To delete this location press the star key twice The LED will now turn green Enter the pin number required a conformation bleep will be heard If further pin numbers are to be programmed select the next available location number xxx Setting the Unlock Time for Zone 1 Enter programming mode A Long bleep will be heard and the green power LED will turn orange Press the key then the 1 key the orange LED will start to flash Enter the time in seconds for the unlock time from 00 to 99 seconds Zone 2 programming Programming A User Pin number to Zone 2 Note Zone 2 has 10 locations available 00 09 Enter programming mode A Long bleep will be heard and the green power LED will turn orange Press the key followed by the 4 key The orange LED will start to flash Enter the vacant location number you want to programme the pin number in to xx The green programming LED top left of keypad will illuminate Note if this location already has a pin number the LED will turn red To delete this location press the star key twice The LED will now turn green Enter the new pin number required a conformation bleep will be heard If further pin numbers are to be programmed select the next available location number xx Setting the Unlock Time for Zone 2 Enter programming mode A Long bleep will be h
Download Pdf Manuals
Related Search