SP 2000 USER MANUAL SpacePak Series Product Data
Contents
1. Blue 3 pee ______ NC Do not connect wire ty it yl it SPRR 2612 SPPR 2610 Load as NPN ty it Website www telcosensors com E Mail info telcosensors com Made in Denmark Brown 1 Increase sensitivity slowly from minimum full counter clockwise until the yellow I 0 2 output indicator changes Increase a little further until the red Insufficient Signal White indicator is off White 8 ne Black 4 goad EE 3 Select target object with smallest dimensions and most translucent surface Blue 3 NC Do not connect wire Place target object between SPRR SPPR and retro reflector If the output 4 changes the sensitivity is adjusted correctly If the output does not change then proceed to step 5 SPRR 2612 SPPR 2610 Load as PNP 5 Remove the object and decrease the sensitivity by turning he sensitivity potentiometer counter clockwise until the red Insufficient Signal indicator is on Brown F Place target object between SPRR SPPR and retro reflector If the output changes Grey 6 the sensitivity is adjusted to suit the target but the adjustment is very delicate and wise N C not advisable Black c Note For SPPR is it essential to use a retro refector that depolarises the reflected light Telco a N O type ILR3 and other similar types may be used while many reflecting tape types not are advisable ue D w SPRR 2912 SPPR 2910 Relay output Time Delay Adjustment The o2. 0 12m Adjustments reflective SPRR 2912 T 12 240 V dc On Off Delay adjustable SPRR 2912 20 240 V ac Relay 5 Output Mode Selection SPPR 2610 T i On Off Delay The output mode can be selected via an integral light dark switch Refer to Output Logic table Bataa SPPR 2610 EOAR DENARNE 0 10m for output mode reference SPPR 2910 T 12 240 V de On Off Delay adjustable 3 j R 5 fl reflective SPPR2910 20 240 Vac Beray light Operated N CI ails een acer e a e E AES Note Measured against 85 mm retro reflector JEEP ji R Enables the output to be active Turn switch to full counter Illustration Dark Operated N O when there is an object present clockwise position Output Logic r 7 Relay Transistor Output 144 Led Indicators Detection Output mode Output Output ndieator Indicators ignal l Object present C1 Nol Inc je o of lt TAR bc os sect i ooo UE oe on oa lt _ Sensitivity adjustment O Output yellow r f 5 N Light operated C NO NC o Powe n N C zF pen Off Ge lt lt DarkLight switch al Power green t l Ne Spy all Se m Object absent Light operated C No xc TR m 5 _ On delay adjustment only T models N C 0 10 lt u g m ho 4 Off delay adjustment only T models N GA aem eren off Sensitivity Adjustment Connection Proceed with the following steps Wiring Diagrams A 1 Make sure there is no object present between SPRR SPPR and retro reflector Brown 1 White b 4 Black a
3. SP 2000 USER MANUAL SpacePak Series Photoelectric retro reflective sensors amp polarized retro reflective Product Data EN Connection Wires Pins o eos Telco 7 e SENSOTS Cable 4 pin M12 plug Electrical Data Supply Supply ac Brown Pin 1 Brown DC AC Supply Supply ac Blue Pin 3 Blue Supply Voltage 10 30 V dc 12 240 V dc 20 240 V ac Output NC Grey z Voltage ripple 15 Output NO Black Reverse polarity protected Yes Output COM White Short circuit protected Yes Output PNP Black IAB IACK Sensor plug Current consumption lt 65 mA lt 70 mA Output NPN White Pin 2 White R 1 open 1 close Output relay 240Vac 3A Output transistor 200 mA 30 V dc Mounting amp Alignment Environmental Data Mounting amp Alignment Temperature operation 20 to 55 C Sealing class IP 67 1 Position the sensor pointing at a retro reflector ac CE i Approvals 2 Align by moving sensor horizontally and vertically until the output status changes when de CE pointing at retro reflector and when no object is present refer to Output Logic table e 3 Fasten the sensor securely using the enclosed mounting bracket and hardware Avoid Available Models acute angles on cable close to sensor F Sensing Model Supply Voltage Output Time Delay Range SPRR 2612 T On Off Delay Retro SPRR 2612 TOD ce ANN z
4. n delay enables outpu for the adjusted time period In Dark operated mode The off delay enables outpu The time delay is adjustable between 0 10 sec Om detay counter clockwise respectively Giigtatay counter clockwise respectively T models signal to only activate if an object in the detection area is present signal to remain activated for the adjusted time period Increase or decrease on delay by turning potentiometer clockwise or Increase or decrease off delay by turning potentiometer clockwise or V 1 11 Part Number 0666220632 February 2011 edition Telco A S reserves the right to make changes without prior notice Warning This product is not a safety system and must not be used as such It is not designed for personnel safety applications and must not be used as a stand alone personnel safety system
Download Pdf Manuals
Related Search