DAG1000/2000 Series FXSFXO Voice Gateway User Manual V2.0
Contents
1. 10 Dinstar Technologies Co Ltd DINSTAR DAG1000 2000 Series FXS FXO Voice Gateway User Manual Default username and password admin admin click OK to entry into web interface System Information Status amp Statistics Quick Setup Wizard Network SIP Server Port Advanced MAC Address 00 1F D6 97 02 89 Network Mode Bridge IP Address 172 16 77 4 255 255 0 0 DNS Server 202 96 128 68 202 96 134 133 Call amp Routing System Uptime Oh 00m 21s Manipulation Network Traffic Stat Received 36183 bytes Sent 42893 bytes Maintenance Version DAG1000 4540 Rev 2 11 05 03 PCB 23 1 LOGIC 0 BIOS 1 Built on Apr 9 2012 15 41 26 Figure 4 1 2 DAG Configure Interface 4 2 Navigation Tree DAG series voice gateway web configuration interface mainly includes navigation tree and the right configuration interface Choose navigation tree in order to entry into the configuration interface Status amp Statistics Quick Setup Wizard Network Local Network VLAN MAC Clone DHCP Server DMZ Host Foward Rule static Route ARP Config SIP Server Port Advanced Call amp Routing Manipulation Maintenance Figure 4 2 1 Navigation Tree When device is in bridge mode navigation tree won t display routing configuration items 11 Dinstar Technologies Co Ltd DINSTAR DAG1000 2000 Series FXS FXO Voice Gateway User Manual and the following DHCP service DMZ host f2. Figure 4 8 11System Configuration Interface 39 Dinstar Technologies Co Ltd DINS TAR DAG1000 2000 Series FXS FXO Voice Gateway User Manual STUN Server Address STUN server IP address STUN Server Port STUN server port Primary NTP server address Primary NTP server IP address system default is us pool ntp org Primary NTP server port Default is 123 Secondary NTP server address Default is 18 145 0 30 Secondary NTP server port Default is 123 Every certain time synchronization gateway time the system default SYN Interval every 3600 s synchronous once Time zone can be chosen System default the United States central Time Zone time Chicago Reboot Time Set a restart time for device the device will reboot at this time WEB Port Gateway web port default is 80 Access Web by WAN Enable or disable accessing web by WAN Telnet Port Telnet service port default is 23 4 9 Call amp Routing 4 9 1 Port Group Port group parameter include Index description etc Port group configure interface as follow 40 Dinstar Technologies Co Ltd DINS TAR DAG1000 2000 Series FXS FXO Voice Gateway User Manual Port Group Add Index Description Primary Display Name Primary SIP UserID Primary Authenticate ID Primary Authenticate Password Ir O Of secondary Display Name secondary SIP User ID secondary Authenticate ID Secondary Authenticate Password Offhiook Auto Dial Auto Dial Delay Time Port Select
3. DINSTAR DAG1000 2000 Series FXSFXO Voice Gateway User Manual V2 0 Dinstar Technologies Co Ltd Address Floor 6 Guoxing Building Changxing Road Nanshan District Shenzhen China 518052 Telephone 86 755 26456664 Fax 86 755 26456659 Email Sales dinstar com supportO dinstar com Website www dinstar com Revision Records File Name DAG1000 2000 Series FXS FXO Voice Gateway User Manual Document Version Revised by Technical Support Department Table of Contents EQUIPMENT NO tel d Le E 1 A ita 1 1 2 Equipment appearance E 1 IFS POWE TEE 2 1 4 Network EE Str 2 Led FUNCUONS ana E 3 Lee L Protocol StanGelrd SUD DO RECO eege 3 1 5 2 VOICE and Fax parametelS cascos 3 1 5 3 Supplementary Service i 3 O tore E N eae 4 EN Let E UE 4 2 1 1 Phone or Extension NUMDEr in 4 EE HE ee 4 22 A AO 6 WEE 5 23 Cal WaN Laa 5 PARE E E E EE 5 ZA BIN TAN E 5 2 4 2 Attended NEE 6 AE ee ene ee en ee ee 6 2 6 Sending and RECEIVING Foe leali 8 2 6 1 DAG FXS support four fax modes oooococococococccoonanononcononanonananono 8 2012 1 39 ana Pass MOU 0 a 8 EOcal UR OD Chall OM acts 8 A e IA 8 A EE 8 3 3 Configure LAN Porte IP Address 8 EE 9 A rea 9 BEEN A A E E E eco widen ene 9 A 2 KOJN WEB dic ai 10 LN WV 6 Fo HES 6 T OCs A E O aas 11 4 53 State ana Stals tE a ee tee ee nee nee 12 ue E Ke tel A E Elle EE 12 4 3 2 Registration nto E ele Riina 13 E e IR e E lai 14 Aa RTP SESSION ot
4. Description Remote Address Remote Port Heartbeat ll Enable Figure 4 9 2 IP Trunk Configuration Interface Index IP trunk number it is range from 0 to 63 Da The description of IP trunk its purpose is so you can identify the IP trunk with a Description meaningful name Remote Address Peer IP address or domain name Remote Port Peer SIP port Heartbeat Default is disable if enable DAG will send OPTION to peer device 4 9 3 Routing Configuration Figure 4 9 3 Routing Parameter Configuration Interface Routing Parameter Calls from IP Routing before Manipulation Calls from Analog Line Routing before Manipulation This option determines the following routing of call take effect before or after manipulation 43 Dinstar Technologies Co Ltd 2 DINS TAR DAG1000 2000 Series FXS FXO Voice Gateway User Manual 4 9 41 P Tel Routing IP gt Tel Routing Add Index 31 Description La Calls from O IPTrunk Any Le SIP Server Caller Prefix pod Callee Prefix Calls to Po Port Group Le NOTES any in Callee Prefix or Caller Prefix means wildcard string Figure 4 9 4 IP Tel Routing Parameter Routing priority 0 31 0 is the highest priority NE its purpose is so you can identify thelP0 gt Tel routing with a Description meaningful name Calls from IP Trunk SIP Server any means any IP Caller number Prefix its length normally less or equal to caller number which helps to matchi
5. TCP UDP Traffic 232 59 41 216 Figure 4 3 3 TCP UDP Statistics Information Figure 4 3 3 shows TCP sending and receiving UDP sending and receiving packets of statistical information since the device launched 4 3 4 RTP Session Statistics Figure 4 3 4 RTP Session Statistics Figure 4 3 4 display real time RTP conversation flow data information includes Port voice codec packet period local port peer IP peer port sent packets receive packets lost packets jitter and duration 4 4 Quick Setup Wizard Quick configuration guide will guide users to configure the device step by step Users only need to configure network SIP server and sip port in quick setup wizard Basically after these three steps users are able to make voice call through device 4 5 Network Configuration 4 5 1 Local Network DAG FXS FXO hybrid gateway has two kinds of work mode route and bridge When DAG is set route mode the DAG will work as small router and NAT function has enabled In this 14 Dinstar Technologies Co Ltd DINSTAR DAG1000 2000 Series FXS FXO Voice Gateway User Manual situation WAN port is normally connect to uplink router switch or ADSL MODEM LAN port used to connect local computer or other network device such as Ethernet switches Hubs etc When DAG is set bridge mode WAN and LAN port are the same The DAG just work as two ports or four ports Ethernet switch When it set to bridge mode only need t
6. 4 6 SIP Server SIP server introduction 1 SIP server is the main component of VolP network and responsible for establishing all the SIP phone calls SIP server also called SIP proxy server or registered server IPPBX and the soft switch can act as SIP server role 2 Usually SIP server does not participate in the media process In SIP network the media always using end to end to hand the consultation In some particular situation or business processing such as Music On Old SIP server will actively participate in the media negotiation Simple SIP server is responsible only for establisnment maintenance and cleaning conversation don t interfere in call While relatively complex SIP server also called SIP PBX It not only provides the basic call and basic conversational support also offer plenty of business such as Presence Find me Music On Hold 3 SIP server based on Linux platform such as OpenSER sipXecx VoS Mera etc 4 SIP server based on windows platform such as miniSipServer Brekeke VolPswitch etc 23 Dinstar Technologies Co Ltd DINS TAR DAG1000 2000 Series FXS FXO Voice Gateway User Manual 5 Carrier grade soft switch platform such as Cisco Huawei Zteetc SIP server configuration interface as follows SIP Server Primary SIP Server Primary SIP Server Address 172 16 100 102 Primary SIP Server Port Default 5060 Register Interval Default 1800 Heartbeat E Enable Secondary SIP Ser
7. Pick Up on Group Port El Port o Fxs El Port 1 FXS E Port 2 FX5 Port 3 FXS E Port 4 FX0 Port 5 FXO Port 6 FXO Port 7 FXO Figure 4 9 1 port group configuration interface es Port group Number It uniquely identifies a route range from ndex 0 7 o Port group description its purpose is so you can identify the Description port group with a meaningful name Port group display which will be used in SIP message example INVITE sip bob biloxi com SIP 2 0 Via SIP 2 0 UDPpc33 atlanta com branch z9hG4bK776asdhds Primary Secondary Display Name Max Forwards 70 To Bob lt sip bob biloxi com gt From Alice lt sip alice atlanta com gt tag 1928301774 Here Bob and Alice is the display User account information provided by VolP service provider Primary Secondary SIP User ID ITSP Usually in the form of digit similar to phone number or actually a phone number SIP service subscriber s Authenticate ID used for Primary Secondary Authenticate ID oe authentication Can be identical to or different from SIP User 41 Dinstar Technologies Co Ltd DINSTAR DAG1000 2000 Series FXS FXO Voice Gateway User Manual Primary Secondary Authenticate Password of SIP user ID Password Offhook Auto Dial Set Auto dial number to complete one stage dialing Auto Dial delay time Delay time of FXO port send auto dial number e It specifies the policy for selecting port in a port group e Ascending the system always se
8. forbid call forward unconditional Deactivate Call Forward Busy Activate 90 forward busy number Call Forward Busy Deactivate 91 forbid call forward busy Call Forward No Reply Activate 92 forward no reply number Call Forward No Reply Deactivate 93 close this function Do Not Disturb Activate 78 enable DND function Do Not Disturb Deactivate 79 close DND function Dial Voicemall 200 visit voice mail box LA 00 Dinstar Technologies Co Ltd DINS TAR DAG1000 2000 Series FXS FXO Voice Gateway User Manual Note Private services are open by default 4 8 7 System Parameter System parameters include STUN NTP Provision WEB parameter Telnet 1 STUN STUN Simple Traversal of UDP over NATS is a network protocol It allows users back of NAT find their own public network address NAT type and internet end port have been bound by NAT for a local port Two back of NAT router devices established UDP communication through this information STUN doesn t support TCP connection and H 323 2 NTP Network Time Protocol NTP is a computer time synchronization protocol System parameter configuration interface as follow System Parameter STUN Enable NTP Enable Primary NTP Server Address US poolntp org Primary NTP Server Port secondary NTP Server Address Secondary NTP Server Port SYN Interval Time Zone Daily Reboot Reboot Time WEB Parameter WEB Port Access WEB by WAN Telnet Parameter Telnet Port
9. 2000 series FXS FXO hybrid analog gateway is access gateway based on IP network It can provide low cost simple operation VoIP solutions for small enterprise the family office remote office and branch enterprise DAG connects to analog telephone fax and traditional analog PBX with standard voice interfaces and provided high quality voice service DAG series FXS FXO hybrid VolP access gateway has life line function DAG series FXS FXO hybrid gateway includes following model m DAG1000 4S40 m DAG1000 8S80 This manual mainly to DAG1000 4S40 as examples introduce the function of devices and parameter configuration 1 2 Equipment appearance Figure 1 1DAG1000 4540 Figure 1 2 DAG1000 8580 Dinstar Technologies Co Ltd DINS TAR DAG1000 2000 Series FXS FXO Voice Gateway User Manual 1 3 Power supply DAG1000 4S40 is Cassette equipment with placed on desk and adopts AC 110 240V power supply with the power adapter convert to 12V DC power Power parameters Input 100 240VAC 50 60Hz Output 12V DC DAG2000 8S80 can be installed in the 19 inch frame and adopts AC power supply Notes Because power adapter interface is different in different country please confirm the interface standard with us before shipment 1 4 Network Applications All over the world IP LAN DAG1000 80 FXO lines FXO olP access gateway DAG1000 85 IP Network UE FXS g G m PBX VolP access atewa
10. 7 Voice VLAN uses following separate P interface Obtain an IP address automatically Use the following IP address IP Address subnet Mask Default Gateway Management VLAN Fl Enable Management 802 10 VLAN ID 0 4095 Management 802 1P Priority 0 7 Management VLAN uses following separate IP interface Obtain an IP address automatically Use the following IP address IP Address subnet Mask Default Gateway Figure 4 5 3 VLAN parameter configuration Table 4 5 1VLAN parameter configuration Fill out an ID to describe a data VLAN group ID 0 Data 802 1Q VLAN ID 0 4095 used to management VLAN can t used to service Data VLAN configure WW 802 1 protocol to control network traffic priority Data 802 1p Priority 0 7 o Priority from 0 7 18 Dinstar Technologies Co Ltd DINS TAR DAG1000 2000 Series FXS FXO Voice Gateway User Manual Fill out an ID to describe a voice VLAN group ID 0 Voice 802 1Q VLAN ID 0 4095 used to management VLAN can t used to service configure cu 802 1 protocol to control network traffic priority Voice VALN Voice 802 1p Priority 0 7 o Priority from 0 7 IP address Can use dynamic or static IP address Voice VLAN DNS Server Can use dynamic or static DNS server address Fill out an ID to describe a data VLAN group ID 0 Management 802 1Q VLAN used to management VLAN can t used to service ID 0 4095 configure Management Management 802 1p Priority
11. 802 1 protocol to control network traffic priority VLAN 0 7 Priority from 0 7 IP address Can use dynamic or static IP address Management VLAN DNS server Can use dynamic or static DNS server address Note restart the device to take configuration effect 4 5 3 MAC Clone Routing mode MAC Clone This page provides the setting MAC address of WAN PC MAC Address BC AE C5 44 79 E9 Device MAC Address 00 1F D6 97 02 7D Note The device must restart to take effect Figure 4 5 4 MAC Clone Interface More client in LAN have already can t share internet used the traditional gateway set law Because P address binding in only a legitimate MAC address by ISP If the ISP s switch discovers illegal MAC address it will refuse the service The best way is MAC clone for MAC binding Most ADSL MODEM broadband router wireless router have this feature The principle of MAC address clone is deliberately exposed MAC address of bound computer to the ISP server and let the ISP server think that used only a single piece of computer in fact many computers in sharing the Internet This function used to prevent ISP limiting to share the Internet 19 Dinstar Technologies Co Ltd DINSTAR DAG1000 2000 Series FXS FXO Voice Gateway User Manual Note Restart device to take configuration effect 4 5 4 DHCP Server Routing mode Under route mode DAG network part as a small router to configure DHCP service that DAG as a DHC
12. FXO Offhook Onhook when Busy Tone Detected No Current Detected Current Disconnect Threshold Ho RTP Detected Period without RTP Packet Dt Impedance AC Impedance 600 Ohm 600 Ohm C E Enable Enable Enable D N Il n alla in Enable 3 LI Enable After Ring Enable Enable v Enable Enable Enable Enable Enable 0 ms Enable S CH mm 50 Ohm Figure 4 8 1 FXS FXO Parameters Configuration Interface Dinstar Technologies Co Ltd 27 DINS TAR DAG1000 2000 Series FXS FXO Voice Gateway User Manual FXS FXO parameters description Hear the dial tone when pick up the phone Choose the national standards Call Process Tone from the drop down box Default is the United States With the help of dialing timeout you can limit the time while users typing the digits from an extension If the timeout expire while the user is typing in Timeout for dialing the extension then DAG will consider the extension as complete and it will try to send to SIP server Default value is 4 seconds Timeout for This timer set how long the caller party waiting when makes outgoing call answer Outgoing call on extension Timeout for This timer set how long the phone sets ringing when get incoming call answer Incoming call Life Line when Registration Under device are not registered circumstance call inbound directly from Failed corresponding FXO port Send Polarity Reversal Enab
13. LAN port IP address and dialing 159 to inquire WAN port IP address 3 2 Factory Reset After picking up dial 166 000000 then onhook and restart after Setting successful 3 3 Configure LAN Porte IP Address Before configuration please ensure 1 The device is power on 2 devices connecting Dinstar Technologies Co Ltd DINS TAR DAG1000 2000 Series FXS FXO Voice Gateway User Manual to network 3 Telephone is connecting to FXS port of device 1 Configure dynamic IP address by DHCP Offhook Dial 150 2 Onhook If the equipment hint success after 10 seconds and restart the equipment Power off then power on 2 Configure Static IP address Offhook Dial 150 1 Onhook Then configure IP and mask as follow e Configure IP address Offhook input 152 172 16 0 100 onhook e Configure subnet mask Offhook input 153 255 255 0 0 onhook e Configure gateway IP address Offhook input 156 172 16 0 1 onhook 3 Query the IP address of device Offhook input 158 4 If the DAG serial uses PPPoE method to get IP address it need to configure by web browser Note the telephone will play voice prompt Setting successfully if the step is correct 4 WEB Configuration 4 1 WEB Login Device is connecting to network properly refer to chapter 3 Operation Offhook and dial 158 to inquire device IP address 4 1 1 Login Device LAN port default IP address is
14. Protocol ICMP echo request packets addressed to a destination host Determining the intermediate routers traversed involves adjusting the time to live TTL aka hop limit Internet Protocol parameter Frequently starting with a value like 128 Windows or 64 Linux routers decrement this and discard a packet when the TTL value has reached zero returning the ICMP error message ICMP Time Exceeded Tracert works by increasing the TTL value of each successive set of packets sent The first set of packets sent have a hop limit value of 1 expecting that they are not forwarded by the first router The next set have a hop limit value of 2 so that the second router will send the error reply This continues until the destination host receives the packets and returns an ICMP Echo Reply message Trace route uses the returned ICMP messages to produce a list of hops which usually consists 51 Dinstar Technologies Co Ltd DINSTAR DAG1000 2000 Series FXS FXO Voice Gateway User Manual of routers and layer 3 switches that the packets have traversed The timestamp values returned for each router along the path are the delay aka latency values typically measured in milliseconds for each packet Tracert introduce 1 Clicktracerttest 2 Fill IP address or domain connected click start Tracert Test Destination Max Hops 1 455 Stop Information Figure 4 11 6 Tracert Test Interface 4 11 7 Password Modification Includes WE
15. VLAN Virtual Local Area Network e ARP Address Resolution Protocol e CID Caller Identity e DND Do NOT Disturb e DTMF Dual Tone Multi Frequency e NTP Network Time Protocol e DMZ Demilitarized Zone e STUN Simple Traversal of UDP over NAT e PSTN Public Switched Telephone Network 54 Dinstar Technologies Co Ltd
16. a a RO ima Phone Phone Phone Phone Phone Phone Phone Phone Figure 4 1 Network Applications Dinstar Technologies Co Ltd DINS TAR DAG1000 2000 Series FXS FXO Voice Gateway User Manual 1 5 Functions and Features 1 5 1Protocol standard supported e SIP V2 0 RFC 3261 3262 3264 SDP RFC 2327 e REFER RFC 3515 e RTP RTCP RFC 1889 1890 STUN RFC 3489 e ARP RARP RFC 826 903 e SNTP RFC 2030 e DHCP PPPoE e TFTP HTTP HTTPS DNS DNS SRV RFC 1706 RFC 2782 e VLAN 802 1P 802 1Q e Diff Serve 1 5 2 Voice and Fax parameters e G 711A U law G 723 1 G 729AB e Comfortable Noise Generation CNG e Voice Activity Detection VAD e Echo Cancellation G 168 e Adaptive Dynamic J itter Buffer e Voice and fax gain control e Hook flash Detect e T 38 Pass through DTMF Mode Signal RFC2333 INBAND 1 5 3 Supplementary service e Busy tone detection No current take out stitches detection Voice interrupted detection One stage dialing Two stage dialing e PSTN exterior ports polling Polarity Reversal e FAS Fake billing correction DC AC impedance config Calls detection Bellcore Type 1 amp 2 ETSI DTMF Dinstar Technologies Co Ltd DINS TAR DAG1000 2000 Series FXS FXO Voice Gateway User Manual e Direct IP Call o Primary and secondary SIP account 32 inbound outbound routing Number manipulation e Dial plan set Life line 2 Basic Ope
17. special areas of the network and different from the external network or intranet Public server that does not contain confidential information usually placed in DMZ such as web Mail FTP etc Accuser from intranet can visit the service of DMZ but can t come into contact with confidential or private information stored in the network Even if DMZ server is damaged it will not be confidential information in the internal network DMZ Host DMZ Host IF Address Enable Note The IP address needs to be in the same subnet with LAN port Figure 4 5 6 DMZ Configuration Interface Note After configuration restart device configuration validation 4 5 6 Forward Rule Routing mode In some cases LAN network equipment need to provide some communication in WAN network such as port for 21 FTP service This time can be configured forwarding rules for the network equipment Service ports namely the need to provide service network mouth WAN ports IP address that LAN network provide services to the mouth of the network equipment IP address the protocol is TCP or UDP The different between forward rule and DMZ host is that DMZ Host offers continuous multiple Port 0 1024 and all the foreign communication agreement while the forward rule offers a single or a few port foreign communication on some protocol When the conflicts exist between forward rule and DMZ host the configuration of forwarding rules is preferred Forward rule confi
18. 00 Series FXS FXO Voice Gateway User Manual Inquire LAN port IP address Dial 158 to obtain device WAN port IP address Inquire WAN port IP address Dial 159 to obtain device WAN port IP address Inquire Phone Number Dial 114 to obtain port account 150 0 means pppmodem 150 1 means static P Setting IP Mode 150 2 means obtain IP address by DHCP 150 3 means PPPOE 157 0 set network work mode to routing mode 157 1 set network work mode to bridge mode Network Work Mode Configure IP Address 152 IP set gateway IP address Network subnet mask configure 153 subnet mask set gateway subnet mask Network Gateway Configure 156 gateway IP set gateway Renew DHCP 193 set dynamic IP again Allow access web through WAN port 160 1 don t allow access Access Web by Wan in Rout Mode web through WAN port 160 0 Reset Factory 166 000000 reset factory Restart Device 111 restart device When call process dial into call hold Recovery the call through Call onhold offhold hook flash or Call by IP Directly dial the end user IP to call Call Waiting Activate 51 enable call waiting function Call Waiting Deactivate 50 forbid call waiting function If the call transfer to 801 first hook flash and then dial the 87 801 Blind Transfer Call Forward Unconditional Activate 72 phone number transfer the call from the phone number Call Forward Unconditional 7 73
19. 192 168 11 1 WAN port default obtain IP address by DHCP Advice to modify the IP address of the local computer equipment and ensure that 9 Dinstar Technologies Co Ltd 2 DINS TAR DAG1000 2000 Series FXS FXO Voice Gateway User Manual are on the same IP segment with Windows 7 as an example the local computer IP address change for 192 168 11 10 Internet Protocol Version 4 TCP IPv4 Properties _2 ez You can get IP settings assigned automatically if your network supports this capability Otherwise you need to ask your network administrator for the appropriate IP settings Obtain an IP address automatically Use the following IP address IP address Subnet mask Default gateway Obtain DNS server address automatically Use the following DNS server addresses Preferred DNS server 8 8 Alternate DNS server CD Validate settings upon exit Figure 4 1 1Modify IP address Check connection between computer and device click Start gt run gt input cmd run ping 192 168 11 10 t order to check the connectivity between them 4 1 2 Login WEB Open web browser then input IP address of device Press Enter it pop up logging on identity authentication interface Authentication Required The server 172 16 77 10 80 requires a username and password The server says Web Config System User Name admin Password rz Figure 4 1 1 DAG FXS Login Interface
20. B username and password Telnet username and password modify Note Default web and telnet username and password is admin admin 52 Dinstar Technologies Co Ltd DINSTAR DAG1000 2000 Series FXS FXO Voice Gateway User Manual Password Modification Web Config Old Web Username Old Web Password New Web Username New Web Password Confirm Web Password Telnet Config Old Telnet Username Old Telnet Password New Telnet Username New Telnet Password Confirm Telnet Password Figure 4 11 7 Password Modification Interface 4 11 8 Factory Reset Click Apply to restore the factory settings Factory Reset Click the button below to resetto factory default settings Figure 4 11 8 Factory Reset Interface 4 11 9 Device Restart Click the Save button in the Configuration page to save the changes to the equipment configuration The following screen confirms that the changes are saved If the changes need restart reboot or power cycle the equipment to make the changes take effect Restart Click the button below to restart the device Restart Figure 4 11 9 Device Restart 53 Dinstar Technologies Co Ltd DINS TAR DAG1000 2000 Series FXS FXO Voice Gateway User Manual 5 Glossary e DNS Domain Name System e SIP Session Initiation Protocol e TCP Transmission Control Protocol e UDP User Datagram Protocol e RTP Real Time Protocol e PPPOE point to point protocol over Ethernet e
21. P server in network Start and end address of address pool determine the range of IP address automatically assigned to other devices e IP Expire Time means use time of assigned IP address More than the lease time if the IP address is not used by network equipment IP address will be recovered e Subnet mask gateway DNS and other information configured by DHCP protocol Configuration interface as figure 4 5 5 DHCP Server Config DHCP Server Enable IP Pool Starting Address IP Pool Ending Address 192 168 11 199 IP Expire Time Subnet Mask Optional 255 255 255 0 Default Gateway Optional 192 168 11 77 Primary DNS Server Optional 202 96 128 68 Secondary ONS Server Optional 202 956 134 133 Note The device must restart to take effect Figure 4 5 5 DHCP Configuration Interface Note When configure start and end IP address subnet mask and gateway please set the same segment with LAN port Otherwise device will not work normally After configuration restart device configuration validation 4 5 5 DMZ Host Routing mode DMZ Demilitarized Zone connect web e mail etc server allowed external to access to this area Make the internal network located the back of the zone of confidence and not allow any access separation of inside and outside the network protect user 20 Dinstar Technologies Co Ltd DINS TAR DAG1000 2000 Series FXS FXO Voice Gateway User Manual information DMZ can be understood that a
22. User Manual 4 11 3 Data Backup The process data backup 1 Click Data Backup 2 Click Backup to backup data to PC Data Backup Click Backup for download configuration file to your computer Figure 4 11 3 Data Backup Interface 4 11 4 Data Restore The processes of data restore 1 Click Data Restore 2 Browse file select data file 3 Click Restore and then import successfully the device will restart automatically Data Restore send data file from your computer to the device Configuration Figure 4 11 4 Data Restore Interface 4 11 5 Ping Test Send test data packets to IP check each other whether have response and statistical response time It is ping Used to test internet and analyzed network fault Application format Ping IP address It is used to check the network connectivity or network connection speed command Pinginstructions 1 Click ping test 50 Dinstar Technologies Co Ltd DINS TAR DAG1000 2000 Series FXS FXO Voice Gateway User Manual 2 Fill IP address or domain connected click start 3 Received a message indicates that network connection normal or network connected to a fault Ping Test Destination Mumber of Ping 1 100 Packet Size 56 1024 bytes information Figure 4 11 5 Ping Parameter Interface 4 11 6 Tracert Test Tracert is trace router and used to tracking routing Tracert sends a sequence of Internet Control Message
23. a LISIS ora 14 A A QUICK te WOEN 14 4 9 Network Configuratio iena 14 E ee e o o 14 A32 VLAN e EE 17 4 5 3 MAG Clone Routing mode MEN 19 4 5 4 DHCP Server Routing model 20 4 5 5 DMZ Host Routing MOdE io 20 4 5 6 Forward Rule Routing mode 21 A571 Static ROUE Tala 22 EE 23 OM eil 23 4 7 POTECONIOUTAtO Nital 25 Ee Lee PA A ENO 26 AOL FXO PAO PafaMELerS ae 26 48 2 Media Parameter a cn 29 A A errant ceri eect eerr rnrrr mr Tron errr re 31 AOA O a a a 34 LoL 35 4 9 0 FealUre Coeli 37 4 8 7 System ee 39 A stectias gece etieeseaetvve den O TA 40 4 91 POR 40 VAIO CE RR REI IT 42 GELEET ri 43 OO AE KR ROUND rid esuse oats sixeaee eeeeeeeeners 44 49 DTEP TE ROUN aa 45 4 10 Manipulation Configuration ccc cccsseccsssccssscccsssecesssecesssecesseceseeeessees 46 410 1 Ne gt eee ala 46 A E EEEE 47 410 3 Tell Calle 48 ALL MantenNa Esana e aie k tered sree 48 ALSO Parametros 48 4 11 2 Firmware Upload cas 49 GN WR Ee le nenn naaa 50 4 4 Dato Restore aiar 50 ALL PINO OSU nariai Sussenera secu ueuhea se AS 50 e I MG Se RESA ATA 51 4 11 7 Password Modification 52 A PACLOLY RESEL ili 53 4 1 159 Device E 53 A e e UE E PRO UC A 54 DINS TAR DAG1000 2000 Series FXS FXO Voice Gateway User Manual 1 Equipment Introduction 1 1 Overview Thanks for purchasing Dinstar DAG1000 2000 Hereinafter referred to as the DAG series FXS FXO hybrid analog voice gateway DAG1000
24. ake outgoing call G 729 will used as figure 4 8 2 displayed Each kind of coding has a unique type load Payload Type value refer toRFC3551 Default is disable if enable according to the current noise environment dynamically adjust Slience Suppression mute inhibit threshold thus in the user in silent state stop transmission background noise bag and save about VoIP bandwidth In 30 Dinstar Technologies Co Ltd DINS TAR DAG1000 2000 Series FXS FXO Voice Gateway User Manual the low bandwidth environment can reduce the network congestion greatly improving VoIP call effect 4 8 3 SIP Parameter SIP Parameter SUBSCRIBE for MWI Message Waiting Indicator UM Enable RTP Mode in SDP when Call Holding IP to IP Call URI includes user phone Only Accept Calls from Server Anonymous Call Reject Anonymous Call send Flash Event as Ending Dial Key PRACK Value of Refer To refers to Contact Domain Query Type Domain Re resolution Inteval 0 means disable T1 T2 T4 Max Timeout Heartbeat Interval 1 3600s Figure 4 8 3 SIP Parameter Configuration Interface SIP parameter description Voicemail message indicator it is to be realized in the way of NOTIFY Voicemail User ID Access code to voicemail box When call come into holding if select to receive and not send SUBSCRIBE for MWI packet then the local can hear call waiting tone If select to RTP Mode in SDP when C
25. all Holding not receive and not send packet then doesn t play call waiting tone Enable this function users may use the business call IP IP to IP Call address on the phone 31 Dinstar Technologies Co Ltd DINSTAR DAG1000 2000 Series FXS FXO Voice Gateway User Manual URI Includes user phone SIP carries the information the system defaults not open Default is no it indicates the DAG accept incoming call from Only Accept Call from Server SIP server only Enable anonymous call anonymous will include in SIP Anonymous Call message Enable this function reject all anonymous call Disable by Reject Anonymous Call default After hook flash flash event will report flash message to server Send Flash Event l W and server deal with this information as ending Dial Key Dial up use as a end descriptor RFC3262 defined an optional extension methods PRACK provisional ACK Used to support the reliability of the temporary response Its function is to require the receiving party contact with the third party through the use of supplied in the request in the Value of Refer To refers to Contact o address information Refer to field of SIP message fill in contact header Default is A QUERY Voice mail instructions Here DAG work with Elastixes the example introduces how voicemail work in DAG 1 DAG register to Elastix server Corresponding extension number enable voice mail fu
26. at first is 2 3 4 5 6 7 or 8 followed by 6 digits 36 Dinstar Technologies Co Ltd DINSTAR DAG1000 2000 Series FXS FXO Voice Gateway User Manual or first is 13 followed by 9 digits 3 13 15 18 XXXXXXXXX Means that first is 13 15 or 18 followed by 8 digits 4 1 357 9 xx Means that first is 1 2 3 or 5 or 7 8 9 followed by 2 digits 4 8 6 Feature Codec Feature codec includes device function and call function Feature codec as follow Feature Code Feature Codes Use Default Status Device Function Inquiry LAN IP Inquiry WAN IP Enable Je Inquiry Phone Number Setting IP Mode Enable Je Network Work Mode Configure IP Address Enable Le Network Subnet Mask Configure Network Gateway Configure Enable Le Renew DHCP Enable Je Access WEB by WAN in Route Mode Enable e Reset Factory Restart Device Call Function Call Onhold Offhold Enable Je Call Waiting Activate Call Waiting Deactivate 50 Blind Transfer Enable Le Call Forward Unconditional Activate Call Forward Unconditional Deactivate Enable Le Call Forward Busv Activate Lag Ei Enable gt Do Not Disturb Activate Enable Le Do Not Disturb Deactivate Enable Dial Voicemail Note Please finish dialing the feauture code within 25 when using the Call holding function Figure 4 8 10 Feature Code Configuration Interface 37 Dinstar Technologies Co Ltd DINS TAR DAG1000 20
27. ation Can be 25 Dinstar Technologies Co Ltd DINS TAR DAG1000 2000 Series FXS FXO Voice Gateway User Manual Authenticate ID identical to or different from SIP User ID Primary Secondary SIP password which registers to soft switch SIP server Authenticate password Pre assign an extension or phone number so that automatically dial a number Offhook Auto dial as soon as you pick up the phone set Delay 0 3 seconds to automatically dial a number 0 means dial number Auto dial Delay Time immediately Do not disturb the phone set won t receive any calls in case it enabled Caller 1D Enable or disable caller ID for corresponding port call forward unconditional all incoming calls will forward to pre assigned Number for CFU number automatically Call forward on busy if the line is busy the call will forward to pre assigned Number for CFB number automatically Call forward no reply if the line is not answer the call the call will forward to Number for CFNRy pre assigned number automatically 7 If call waiting enabled it will send a special tone if another caller tries to reach Call Waiting you when you are using your telephone Play Call Waiting Tone Enable call waiting tone caller will hear special tone 4 8 Advanced 4 8 1 FXS FXO parameters FXS characteristic parameters include Call progress Tone Timeout for Dialing Send Polarity Reversal etc FXO full name is Foreign Exchange Office It is a kind of voice
28. ed number is 008675526456659 the called prefix can be 0086755 or 00 any means Callee Prefix match any called number Calls to This call routing is routing to port port group IP trunk and SIP server 45 Dinstar Technologies Co Ltd 2 DINS TAR DAG1000 2000 Series FXS FXO Voice Gateway User Manual 4 10 Manipulation Configuration 4 10 1 IP Tel Callee IP Tel Callee Add Index Al Calls from IPTrunk Any 2 SIP Server Callee Prefix Calls to Port Port Group Fl Stripped Digits from Left stripped Digits from Right Prefix to Add Suffix to Add Number of Digits to Leave from Right NOTE any in Callee Prefix or Caller Prefix means wildcard string Figure 4 10 1 IP Tel Callee number configuration Calls From This call come from IP trunk or SIP server Caller number Prefix its length normally less or equal to caller number which helps to matching routing exactly if caller number Caller Prefix is 2001 the caller prefix can be 200 or 2 any means match any caller number like bob1 29801 Called number Prefix its length normally less or equal to called number which helps to matching routing exactly if called number is 008675526456659 the called prefix can be 0086755 or 00 Callee Prefix any means match any called number 46 Dinstar Technologies Co Ltd DINSTAR DAG1000 2000 Series FXS FXO Voice Gateway User Manual Suffix to Add Add a numb
29. er suffix Number of Digits to Leave from Starting from the right to retain the called number digits Right 4 10 2 Tel IP Caller Tel IP Caller Add Index 3 Description Po Calls from 3 Port Port Group Callee Prefix Po Calls to Port J Port Group wTunk Any SIP Server Stripped Digits from Left Po Stripped Digits from Right Po Suffix to Add Po Po Number of Digits to Leave from Right NOTE any in Callee Prefix or Caller Prefix means wildcard string Figure 4 10 2 Tel IP Caller Configuration parameters are the same with IP gt Tel Callee 47 Dinstar Technologies Co Ltd DINSTAR DAG1000 2000 Series FXS FXO Voice Gateway User Manual 4 10 3 Tel IP Callee TelIP Callee Add Index Description Calls from Port Caller Prefix Callee Prefix Calls to Port Port Group IP Trunk SIP Server Stripped Digits from Left Stripped Digits from Right Prefix to Add Suffix to Add Mumber of Digits to Leave from Right NOTE any in Callee Prefix or Caller Prefix means wildcard string Figure 4 10 3 Tel 1PCallee Configuration parameters are the same with Tel gt IP Caller 4 11 Maintenance 4 11 1 Syslog Parameter Syslog is a protocol used in TCP IP network transmission of record of the standard file information Syslog agreement belongs to a kind of master slave agreement Syslog sender will sent a small text information less tha
30. guration interface as follows 21 Dinstar Technologies Co Ltd DINSTAR DAG1000 2000 Series FXS FXO Voice Gateway User Manual Forward Rule Table Server Port IP Address Protocol Enable Pre CT Notes 1 IP Address needs to be in the same subnet with LAN port 2 Server Port range 0 65535 Figure 4 5 7 Forward rule configuration interface 4 5 7 Static Route Table Static Route Table is IP communication direction in network generally do not need to configure static route When there are many segments in LAN network and need to complete some specific application among these segments the static route need to be configured Static Route configuration interface as follows Static Route Table Dest IP Address Subnet Mask Nexthop io O A EI 2 sl 3 P 4 a sC dI DU 6 E T ai 8 sl Figure 4 5 8 Static route configuration Interface 22 Dinstar Technologies Co Ltd DINS TAR DAG1000 2000 Series FXS FXO Voice Gateway User Manual 4 5 8 ARP ARP brief introduction ARP is address resolution protocol After configuring ARP users can get physical address through device IP address Under TCP IP network environment each host is assigned a 32 bit IP address But the message transmission needs to know the purpose the physical address of the party ARP is a tool that converts IP address into MAC address ARP configuration interface as follows Static Dynamic Figure 4 5 9 ARP Parameters
31. he ring System has two Detect CID modes Before ring and After ring Send Original CID when Enable this function the extension call display will show the PSTN side Call from PSTN number Otherwise the call display will show FXO port number FXO Keep Onhook until Enable this function when call from PSTN to FXO port FXO port set Callee Answered auto dial and pick up after the extension number connection This function Dinstar Technologies Co Ltd DINSTAR DAG1000 2000 Series FXS FXO Voice Gateway User Manual Enable this function when call from PSTN to FXO port FXO port will play Play Hint to FXO prompt tone please dial the extension number o Enable this function FXO port directly sent the dial number without call One Stage Dialing extension biati When call from FXO port to PSTN the interval of sending number by FXO ial Dela port default is 400ms When call from FXO port to PSTN the way of FXO response caller is Polarity Reversal Detected detecting polarity reversal If device detected polarity reversal and then reported to caller to respond and began to billing Delay Time after FXO The time of responding caller by FXO port should be less than this Offhook configuration Onhook when Busy Tone One of the FXO onhook conditions When FXO port detected busy tone Detected FXO will onhook Onhook when NO Current Another of the FXO onhook conditions When FXO port detected no current Detected FXO w
32. her hand up or make another call 2 A quick busy tone followed by a restored call on supported platforms only This means the transferee has received a 4xx response for the INVITE and we will try to recover the call The busy tone is just to indicate to the transferor that the transfer has failed 3 Continuous busy tone The phone has timed out 2 4 2 Attended Transfer Attended transfer allows users to confirm the third party response and decide whether to answer the calls and then transfer this call to the third party Assume that Caller A and B are in conversation Caller A wants to Attend Transfer B to C 1 Caller A presses FLASH on the analog phone for dial tone 2 Dial Caller C s number followed by or wait for 3 seconds 3 If Caller C answers the call Caller A and Caller C are in conversation Then A can hang up to complete transfer 4 If Caller C does not answer the call Caller A can press flash to resume call with Caller B 2 5 Call Features DAG FXS support all traditional and senior phone function Table 2 5 1 Feature Codec Feature Codec Operation nstructions 158 View the LAN port IP address 159 View the WAN port IP address 114 Inquire port account 150 Set the way of obtain IP address Dinstar Technologies Co Ltd DINS TAR DAG1000 2000 Series FXS FXO Voice Gateway User Manual 157 Set network method 152 Set IP address 153 Set Subnet mask 156 Set default ga
33. ill onhook Current Disconnect Default the time of no current should be less than 200ms Threshold Enable this function the system will detect whether RTP flow is interrupted No RTP Detected SE When voice interrupted this function can prevent FXO port hanged Period without RTP Packet How long time no RTP packet allowed Adjust impedance used to impedance matching when FXO and PBX AC DC Impedance docking 4 8 2 Media Parameter Media parameter mainly include RTP start port DTMF parameter Prefered Vocoder Configuration Interface as follow 29 Dinstar Technologies Co Ltd DINSTAR DAG1000 2000 Series FXS FXO Voice Gateway User Manual Media Parameter RIP Start Port DTMF Parameter DTMF Method SIGNAL DTMF Gain OdB e DTMF Send Interval ms Prefered Vocoder Packetization Time ms Rate kbps Silence Suppression Disable w GA Disable Coder Mame Payload Type Figure 4 8 2 Media Parameter Configuration Interface Media parameter description RTP Start Port Default RTP port 8000 DTMF Method SINGAL INBAND RFC2833 It is configurable When RFC2833 is selected RFC2833 Payload Type Optimization payload negotiation parameter with remote side it includes two options Local and remote RFC2833 Payload Type Payload value default is 101 DTMF Gain Default is 0 DB DTMF Send Interval DTMF send signal interval default is 200ms DAG supports G729 G711U G711A G723 while Coder Name it m
34. interface and a trunk connected between central exchange switches and telephone exchange system To central office speaking it simulates a PABX extension and can realize connection among common phone and a multiplexer It also is FXO interface connected with SPC exchanges FXO as ordinary telephone interface and need to remote provide current FXO may connect company s internal PBX service extension and the telecom outside generally speaking FXO is a telephone So just lead a inside to FXO port from company s internal or directly line a straight up in FXO from the telecom FXO parameters include Call progress Tone Timeout for Dialing Send Polarity Reversal 26 Dinstar Technologies Co Ltd DINSTAR etc Configuration interface as follow FAS FAO DAG1000 2000 Series FXS FXO Voice Gateway User Manual Call Progress Tone Timeout for Dialing Timeout for Answer Qutgoing Call Timeout for Answer Incoming Call Life Line when Registration Failed FXS Parameter send Polarity Reversal Detect Hook Flash Min Time Max Time CID Type Message Type Send CID before Ringing Delay of Sending CID after Ringing CFNRy Timeout SLIC Setting FXO Parameter Incoming Gall from PSTN Configuration by FXO Detect CID send Original CID when Call from PST FXO Keep Onhook until Callee Answered Play Hintto FXO Outgoing Call to PSTN One Stage Dialing Dial Delay Answer to Caller when Polarity Reversal Detected Delay Time after
35. l on hold by pressing the flash button on the analog phone if the phone has that button Press the flash button again to release the previously held Caller and resume conversation If no flash button is available use hook flash toggle on off hook quickly You may drop a call using hook flash 2 3 Call Waiting Call waiting tone 3 short beeps indicates an incoming call if the call waiting feature is enabled Toggle between incoming call and current call by pressing the flash button First call is placed on hold Press the flash button to toggle between two active calls 2 4 Call Transfer 2 4 1Blind Transfer Blind transfer used to transfer call to the third party without inform caller Assume that call Caller A and B are in conversation A wants to Blind Transfer B to C 1 Caller A presses FLASH on the analog phone to hear the dial tone 2 Caller A dials 87 then dials caller C s number and then or walt for 4 seconds 3 Caller A will hear the confirm tone Then A can hang up Note Call features enable must be set to Yes in web configuration page Caller A can place a call on hold and wait for one of three situations Dinstar Technologies Co Ltd DINS TAR DAG1000 2000 Series FXS FXO Voice Gateway User Manual 1 A quick confirmation tone similar to call waiting tone followed by a dial tone This indicates the transfer is successful At this point Caller A can eit
36. le polarity reversal to billing A protruding button where putting the receiver boards called Flash Always press is hang up pick up the receiver the fork lift machine from reed called by hand clap called Hook flash Hook flash is a process that put the flash fast by pressing and let go In essence is to cut off the dc access about 80 Detect Hook flash o to 200ms Then switches don t think it s hang on but keep the call taking some other operating The typical application of hook flash is the telephone switchboard When need to transfer the call to other extension then telephone hook flash to transfer the call CID Type There are DTMF and FSK General for the default Message Type The call display formats SDMF and MDMF General for the default After enable this configuration The DAG send caller to phone set before Send CID before Ringing ringing otherwise the caller ID will display after ringing Delay of sending CID after Definite delay timer of caller ID while it set to send caller ID after ringing Ringing Its Default value 500ms The time of no answer call transfer This time must less than call in no CFNRY Timeout answer overtime SLIC Setting Set the unit impedance When the call from FXO interface users can be enable or disabled FXO Configuration by FXO allocation function FXO configuration function includes detect CID Send original CID Play hint to FXO FXO detection calling number and the order of t
37. lects a port from the minimum number The preferential selection of the port can be realized through this mode Cyclic ascending when system selects ports Priority it always begin from the number next to the number selected last time if the maximum priority number is selected last time then the next number is the minimum priority number Port Select and move in cycles like this Descending when system selects ports priority it always begin to select from the maximum priority number Cyclic descending when system selects ports Priority it always begin from the number before to the number selected last time if the minimum priority number is selected last time then the next number is the maximum priority number and move in cycles like this Group ring all ports ringing at the same time l Press extension number to decide which extension on Pick Up on Group the phone 4 9 2 IP Trunk A peer to peer VolP call occurs when two VolP phones communicate directly over IP without IP PBXs between them A peer to peer call can be initiated directly by dialing destination phone number in DAGs and also receiving incoming calls from other peer to peer gateway IP trunk is help to DAGs establish peer to peer call between DAGs and other VolP phones IP trunk will be used in routing configuration 42 Dinstar Technologies Co Ltd DINS TAR DAG1000 2000 Series FXS FXO Voice Gateway User Manual IP Trunk Add Index
38. n 1024 bytes to syslog the receiver The receiver are syslogd syslog daemon or syslog server Syslog message can be transferred by TCP UDP 48 Dinstar Technologies Co Ltd DINS TAR DAG1000 2000 Series FXS FXO Voice Gateway User Manual Syslog level e none Used to misarrange e debug Not including function conditions or the question of other information e notice importance common conditions e warning Early warning information e error Stop error conditions of tools or some part of the realization of the function subsystem Syslog Parameter Enable Figure 4 11 1 Syslog Parameter Configuration Enable send CDR and then send communication information to syslog server 4 11 2 Firmware Upload The process of firmware upload 1 Click Firmware Upload 2 Browse files and choose the loading program Name the file extension ldf 3 Click Upload the upload process will last about 60s and device can automatically restart after uploading The firmware update process don t shut off the power Firmware Upload send ld file from your computer to the device Software SCC EE ee eat Voice pe HESI Asp Notes 1 The upload process will last about 60s 2 The device will restart automatically after upload 3 Do not shut down when the device is uploading Figure 4 11 2 Firmware upload Configuration 49 Dinstar Technologies Co Ltd DINSTAR DAG1000 2000 Series FXS FXO Voice Gateway
39. nction in Elastix and set password As below 32 Dinstar Technologies Co Ltd DINS TAR DAG1000 2000 Series FXS FXO Voice Gateway User Manual Voicemail amp Directory Status Enabled Voicemail Password 111111 Email Address Pager Email Address Email Attachment yes Play CID C yes Play Envelope yes Delete Voicemail C yes IMAP Username IMAP Password VM Options VM Context default WmX Locater Figure 4 8 4 Elastix Voicemail Configuration Interface 2 Check feature code in Elastix and change it as necessary Its default feature codes setting as below Voicemail Dial Voicemail a Iw Enabled Le My Voicemail g m Enabled Le Figure 4 8 5 Elastix Voicemail Setting SUBSCRIBE for MVI Message Waiting Indicator Enable Figure4 8 6 Voice Mail Setting In SIP Parameter 3 Enable voice mail in DAG and Elastix will ask you to leave a message after ringing 15 seconds then Elastix will record and display your message 33 Dinstar Technologies Co Ltd DINS TAR DAG1000 2000 Series FXS FXO Voice Gateway User Manual Voicemail Ringtime Default 15 Direct Dial Voicemail Prefix Direct Dial to Voicemail message type Unavailable Optional Voicemail Recording Gain Do Not Play please leave message after tone to caller Figure 4 8 7 Voicemail Setting 4 DAG dial 200 then dial voicemail account and then ask password for Validation After that the user will hear voice mes
40. ng routing exactly if caller number is 2001 the Caller Prefix caller prefix can be 200 or 2 any means match any caller number like bob1 29801 Called number Prefix its length normally less or equal to called number which helps to matching routing exactly if called number is Callee Prefix 008675526456659 the called prefix can be 0086755 or 00 any means match any called number Calls to This call routing is routing to port or port group 44 Dinstar Technologies Co Ltd DINSTAR DAG1000 2000 Series FXS FXO Voice Gateway User Manual 4 9 5 Tel IP Tel Routing Tel gt IP Tel Routing Add Index 31 Description Calls from O Pon O Portcroup oles prem pd e po Calls to Port Port Group __ lai rm TL Je SIP Server NOTES any in Callee Prefix or Caller Prefix means wildcard string Figure 4 9 5 Tel 1P Tel Parameters Configuration Routing priority 0 31 0 is the highest priority its purpose is so you can identify the routing with a meaningful name Calls From Tel IP call select port or port group Caller number Prefix its length normally less or equal to caller number which Caller Prefix helps to matching routing exactly if caller number is 2001 the caller prefix can be 200 or 2 any means match any caller number like bob1 29801 Called number Prefix its length normally less or equal to called number which helps to matching routing exactly if call
41. nyone means one reports letter T means detected timer overtime x means any data means multiple characters can be behind include 0 means report immediately Digit Map Syntax 1 Supported objects Digit A digit from 0 to 9 Timer The symbol T matching a timer expiry DTMF A digit a timer or one of the symbols A B C D or 35 Dinstar Technologies Co Ltd DINS TAR DAG1000 2000 Series FXS FXO Voice Gateway User Manual 2 Range One or more DTMF symbols enclosed between square brackets and but only one can be selected 3 Range One or more expressions enclosed between round brackets and but only one can be selected 4 Separator Separated expressions or DTMF symbols 5 Subrange Two digits separated by hyphen which matches any digit between and including the two The sub range construct can only be used inside a range construct i e between and 6 Wildcard x matches any digit 0 to 9 7 Modifiers Match 0 or more times 8 Modifiers Match 1 or more times 9 Modifiers Match 0 or 1 times Example Assume we have the following digit maps 1 xxxxxxx x11 and a current dial string of 41 Given the input 1 the current dial string becomes 411 We have a partial match with xxxxxxx but a complete match with x11 and hence we send 411 to the Call Agent 2 2 8 xxxxxx 13XXXXXXXXX Means th
42. o configure WAN port IP address and DNS If set to route mode default LAN port IP will display and it can be change by users Network configure interface as below Local Network Network Mode Route Bridge WAN Port Link Speed amp Duplex Auto Detect Obtain an IP address automatically Use the following IP address IP Address subnet Mask Default Gateway PPPoE Account Password service Name LAN Port Link Speed amp Duplex IP Address subnet Mask DNS Server Obtain DNS server address automatically Use the following DNS server address Primary DNS Server 202 96 128 68 secondary DNS Server 202 96 134 133 Save Figure 4 5 1Route Mode Dinstar Technologies Co Ltd 15 DINS TAR DAG1000 2000 Series FXS FXO Voice Gateway User Manual Local Network Network Mode Route Bridge Network Configuration Link Speed amp Duplex Auto Detect Obtain an IP address automatically 2 Use the following IP address IP Address subnet Mask Default Gateway PPPoE Account Password Service Name DNS Server Obtain DNS server address automatically Use the following DNS server address Primary DNS Server secondary DNS Server 202 96 134 133 Note The device mustrestart to take effect Figure 4 5 2 Bridge Mode gt Link Speed Duplex used to select Ethernet port work mode include 5 kinds of choice Auto Detect 10Mbps half duplex 10Mbps full duplex 100Mbps half duple
43. orward rules and static routing and ARP etc 4 3 State and Statistics 4 3 1 System Information System information interface shows the run information as following figure 4 3 1 below System Information MAC Address Network Mode IP Address DNS Server system Uptime Network Traffic Stat Version 00 1F D6 97 02 89 Bridge 17216 77 4 255 255 0 0 static 202 96 128 68 202 96 134 133 Oh 05m 445 Recelved 859178 bytes Sent 257967 bytes DAG1000 4540 Rev 2 11 05 03 PCB 23 1 LOGIC 0 BIOS 1 Built on Apr 9 2012 15 41 26 Refresh Figure 4 3 1 1 System Information Bridge mode System Information MAG Address Network Mode WAN IP Address LAN Port DNS Server System Uptime Network Connection Qccupancy Ratio WAN Traffic Stat Version 00 1F D6 97 02 89 Router 17216 77 A 255 255 0 0 Static 192 168 11 1 255 255 255 0 202 96 128 68 202 96 134 133 Oh 23m 245 0 Received 342 498 bytes sent 1622567 bytes DAG1000 4540 Rev 2 11 05 03 PCB 23 1 LOGIC 0 BIOS 1 Built on Apr 9 2012 15 41 26 Retrest Figure 4 3 1 2 System Information Router mode Dinstar Technologies Co Ltd 12 DINS TAR DAG1000 2000 Series FXS FXO Voice Gateway User Manual System information Router mode as follow Table 4 3 1 System Information Description MAC address WAN port hardware address The device ID in HEX format Display network mode include bridge and router If it is bridge WAN por
44. rations 2 1 Phone Call 2 1 1 Phone or Extension Number 1 Dial the number directly and wait for 3 seconds Default No dial timeout 2 Dial the number directly and press 2 1 2 Direct IP Calls DAG series device with FXS port allow two parties directly call through IP address The user need only a simulation with the FXS port unit equipment linked together and set up calls not registered Elements necessary to completing a direct IP call 1 Both DAG serial and other VoIP Device have public IP addresses 2 Both DAG serial and other VolP Device are on the same LAN using private IP addresses 3 Both DAG serial and other VolP Device can be connected through a router using public or private IP addresses with necessary port forwarding or DMZ Operation Process 1 Pick up the analog phone then dial 47 2 Enter the target IP address Note No dial tone will be played between step 1 and step 2 Examples Dinstar Technologies Co Ltd DINS TAR DAG1000 2000 Series FXS FXO Voice Gateway User Manual If the target IP address is 192 168 0 160 the dialing convention is 47 then 192 168 0 160 Followed by pressing the key or wait 3 seconds Complete signaling interactive soon after he was called the unit can be heard ringing Note You cannot make direct IP calls between FXSO to FXS1 since they are using same IP It only supports the default destination port 5060 2 2 Call Hold Place a cal
45. sage 4 8 4 Fax Parameter Fax introduction DAG fax parameter includes fax mode Fax sound detection party ECM Rate Fax Config Mode Tone Detection by ECM Enable Rate 14400 bps Figure 4 8 8 Fax Parameter Configure Interface Fax parameter description Mode Fax mode support T 38 T 30 Pass through Modem Adaptive Tone Detection by Fax sound detection mode Caller Callee Automatic ECM Fax error correction information The rate of sending and receiving 34 Dinstar Technologies Co Ltd DINS TAR DAG1000 2000 Series FXS FXO Voice Gateway User Manual 4 8 5 Digit Map Digit Map NOTE Length of Digit Map should not be more than 119 characters Figure 4 8 9Digit Map Gateway is collect digits dialed by user if received a number to be immediately report the efficiency is too low and a large number of take up network resources A reasonable method is concentration sending a message after receiving all number How to judge the gateway receiving all number is the difficulties of this method The solution is the call agent loading a Digit Map to gateway Digit Map includes a series figure characters when the dial up sequence and one received a character string matching it means the number has received neat Digital string contains characters allowed data0 9 letterA D letter T letter x and parts of each string is a choice of dial up solutions means choose a
46. t display Network Mode Network and the WAN port as same as the LAN port Shows WAN IP address of DAG DHCP mode all the field values for the Static IP mode are not used even though they are still saved in the Flash memory The DAG acquires its IP address from the first DHCP server it discovers from the LAN it is connected Using the PPPoE feature set the PPPoE account settings The DAG will establish a PPPoE session if any of the PPPoE fields is set Static IP mode configure the IP address Subnet Mask Default Router IP address DNS Server 1 primary DNS Server 2 secondary fields These fields are set to zero by default Lan Port Shows LAN IP address of DAG if network Mode is bridge LAN port won t display DNS Server Display DNS server IP address and default gateway information System Uptime Time elapsed from device power on to now Network Connection The current NAT mapping maximum number of concurrent mapping Occupancy Ratio number Network Traffic Statics Total bytes of message received and sent by network port Version Includes product mode software version hardware version and built time etc 4 3 2 Registration Information Port Registration Information 0 FXS 1 FXS Port Group Registration Information Figure 4 3 2 Port and Port group registration information Dinstar Technologies Co Ltd DINSTAR DAG1000 2000 Series FXS FXO Voice Gateway User Manual 4 3 3 TCP UDP Statistics
47. teway IP address 193 Obtain IP address through DHCP again 160 1 Open WAN port to access web 166 000000 Factory reset 111 Restart device Call hold 47 IP address call 51 Enable call waiting 50 Disable call waiting 87 Blind transfer 72 Enable Unconditional Call Forward 73 Disable Unconditional Call Forward 90 Enable Busy Call Forward 91 Disable Busy Call Forward 92 Enable No Answer Call Forward 93 Disable No Answer Call Forward 78 Enable DND 79 Disable DND 200 Access Voice mail Switch between incoming calls If not in session flash hook will switch a Flash Hook new channel for new call Dinstar Technologies Co Ltd DINS TAR DAG1000 2000 Series FXS FXO Voice Gateway User Manual 2 6 Sending and Receiving Fax 2 6 1 DAG FXS support four fax modes 1 T 38 CFOIP 2 Pass Through 3 Modem 4 adaptive 2 6 2 T 38 and Pass Through T 38 is the preferred method because it is more reliable and works well in most network conditions If the service provider supports T 38 please use this method by selecting T 38 as fax mode default If the service provider does not support T 38 pass through mode may be used If you have problems with sending or receiving Fax toggle the Fax Tone Detection Mode setting 3 Local IVR Operation 3 1 Inquire IP address Analog phone connected with FXS ports of device then pick up after dial tone dialing 158 to inquire
48. ual 4 7 Port Configuration Port parameters include Send gain receive gain primary display name etc Port Add Fort Tx Gain Rx Gain Primary Display Name Primary SIP User ID Primary Authenticate ID Primary Authenticate Password secondary Display Name secondary SIP User ID secondary Authenticate ID Secondary Authenticate Password Offhook Auto Dial Auto Dial Delay Time OND Do Not Disturb Caller ID Number for CFU Call Forwarding Unconditional Number for CFB Call Forwarding Busy Number for CFNRy Call Forwarding No Reply Call Waiting Enable Play Gall Waiting Tone Enable Figure 4 7 1 Port configuration interface Port parameters introduce as follows It is use to control the volume of conversation Adjust TX gain will affect the Tx Gain end users voice size the default value is 0 BN Its value range from 10 10 dB It is use to control the volume of conversation Adjust RX gain will affect the Rx Gain end users voice size the default value is 0 DN Its value range from 10 10 dB Primary Secondary SIP Primary Secondary SIP account description Its purpose is so you can identify Display Name the SIP account with a meaningful name Primary Secondary SIP User account information provided by VolP service provider ITSP Usually in User ID the form of digit similar to phone number or actually a phone number Primary Secondary SIP SIP service subscriber s Authenticate ID used for authentic
49. ver secondary SIP Server Address Secondary SIP Server Port Default 5060 Register Interval Default 1800 5 Heartbeat E Enable Local SIP Port Use Random Port E Enable Set Local SIP Port 5060 Figure 4 6 1 SIP Server Configuration Interface SIP parameter description Primary SIP Server IP SIP Server IP address or Domain name provided by VolP service provider Primary SIP Server port Service port default is 5060 protects registrar against excessively frequent registration refreshes Register interval while limiting the state Every once in a while send request for registration to the terminal server default is 1800s Heartbeat Heartbeat message detect the connection status between device and SIP server Secondary SIP Server IP e Backup SIP Server s IP address or Domain name provided by VoIP service provider address Secondary SIP Server port Service port default is 5060 protects registrar against excessively frequent registration refreshes Secondary SIP server while limiting the state Every once in a while send request for registration to the Register interval terminal server default is 1800s Secondary SIP heartbeat Heartbeat message detect the connection status between device and SIP server Use Random Port Random SIP service ports for DAG Set Local SIP port Default SIP service port is 5060 24 Dinstar Technologies Co Ltd 2 DINS TAR DAG1000 2000 Series FXS FXO Voice Gateway User Man
50. while others just surf the Internet 1 802 1Q The IEEE 802 1Q standard defines architecture for Virtual Bridged LANs the services provided in Virtual Bridged LANs and the protocols and algorithms involved in the provision of those services No Quality of Service mechanisms are defined in this standard but an important requirement for providing QoS is included in this standard e g ability to regenerate user priority of received frames using priority information contained in the frame and the User Priority Regeneration Table for the reception Port 2 802 1p IEEE 802 1p standard Traffic class expediting and dynamic multicast filtering It describes important methods for providing QoS at MAC level IEEE 802 1p is in fact quite good Lower priority level packets are not sent if there is packets in queued in higher level 17 Dinstar Technologies Co Ltd DINSTAR DAG1000 2000 Series FXS FXO Voice Gateway User Manual queues IEEE 802 1p describes no admission control protocols It would be possible to give Network Control priority to all packets and the network would be easily congested There are three VLAN data VLAN voice LAN and management VLAN VLAN configuration interface as following figure 4 4 3 Data VLAN E Enable Data 802 10 VLAN ID 0 4095 Data 802 1P Priority 0 7 In this case data VLAN uses the default WAN interface Voice VLAN Fl Enable Voice 802 10 VLAN ID 0 4095 Voice 802 1P Priority 0
51. x 100Mbps full duplex default is Auto Detect When select Obtain IP address automatically DAG will obtain IP address by DHCP e When select Use the following IP address that configure DAG to fixed IP address mode When select PPPoE please fill in account and password offered by ISP in internet account and password Notes 1 If select automatically obtain IP address please ensure DHCP server in network and work normally 16 Dinstar Technologies Co Ltd DINS TAR DAG1000 2000 Series FXS FXO Voice Gateway User Manual 2 Under route mode please configure LAN port and WAN port in different segment otherwise DAG can t work normally 3 Under route mode login DAG configuration interface only used LAN port 4 After configuration restart device configuration validation 4 5 2 VLAN Parameter Generally Internet provides only Best Effort Service Since Ethernet is the most spread LAN access technology importance of providing it a quality of service mechanism ought not to be neglected Ethernet technology also used as WAN technology not only as LAN technology Due to rapidly increasing use Internet through Public Switched Telecommunication Network PSTN Telephone Companies are forced to implement IP based networks as their PSTN backbones A network like this without any Quality of Service mechanisms would be disastrous J ust imagine yourself trying to get an emergency call through
Download Pdf Manuals
Related Search