QIG 4ipnet HSG260
Contents
1. e A confirmation dialog box will then appear Click OK to continue 1 Ave vou sure you want to restart the system now j Cancel Copyright 4IPNET INC All rights reserved 12 4ipnet Quick Installation Guide HSG260 Wireless Hotspot Gateway ENGLISH e A Confirm and Restart message will appear on the screen during the restarting process Please do not interrupt the system until the Administrator Login Page appears ft Home Logout Help Setup Wizard Confirm and Restart s e e a S C B9 NP Press Finish button to confirm the settings and restart the system FERAM i Notes The system is trying to locate a DNS server at this stage Therefore a longer startup time is required if the configured DNS cannot be found e When the following Administrator Login Page appears it means the restart process is now completed Username admin icon Copyright 4IPNET INC All rights reserved 13 4ipnet Quick Installation Guide HSG260 Wireless Hotspot Gateway ENGLISH lt User Login gt To verify whether the configuration of the new on demand user account s created via the Setup Wizard has been completed successfully 1 Connect a client device e g laptop PC with wireless interface to scan the configured ESSID of HSG260 e g HSG260 2 and get associated with this ESSID 2 The client device will obtain an IP address automatically via DHCP from HSG260 Open a web browser on a c2. 3 seconds then release right away LED Green OFF and LED Red OFF and then WES Start then BLINKING SLOWLY BLINKING SLOWLY BLINKING NORMALLY BLINKING NORMALLY WES Negotiate Green Red evgce WES Timeout LED Green ON LED Red ON WES Success LED Red ON LED Green ON WES Fail LED Green ON LED Red ON E 9 M ww e i w W O A Copyright 4IPNET INC All rights reserved 2 4ipnet Quick Installation Guide HSG260 Wireless Hotspot Gateway ENGLISH Rear Panel LAN LAN2 LAN3 LAN4 USB 2 0 For attaching an Ethernet cable to an uplink service 3 LAN 1 4 Attach Ethernet cables here for connecting to the wired local network 1 Antenna connector Reverse SMA connectors for attaching antenna as shown in figure 2 Reserved for future use 5 Console Attach the serial cable here to access console interface 5V wwe 2A Attach the power adapter here 7 Restart Reset Press once to restart the system Press and hold for more than 5 seconds to reset to factory default Right Side Panel There is a hole on the right side for Kensington lock If it is not used admin can fill the hole with the rubber plug given Copyright 4IPNET INC All rights reserved 3 4ipnet Quick Installation Guide HSG260 Wireless Hotspot Gateway ENGLISH Hardware Installation Please follow the steps mentioned below to install the hardware of HSG260 1 Place the HSG260 at a best location The best location fo
3. 4ipnet or your IP network Quick Installation Guide HSG260 v2 10 Wireless Hotspot Gateway HSG260 Wireless Hotspot Gateway ENGLISH 4ipnet Quick Installation Guide Copyright Notice This document is protected by USA copynght lawsand other laws Besides the document isthe property of 4IPNET INC You may not copy reproduce distribute publish displa y perform or modify any part of this publication in any form orby any means without prior written permission from 4IPNET INC You may not alterorremove any copyright or other notice from copies of the content All other brand and product namesare claimed or registered marks of their respective companiesororganizations All rights reserved To download up to date version please visit www 4ipnet com Copyright 4IPNET INC All rights reserved i 4ipnet Quick Installation Guide HSG260 Wireless Hotspot Gateway ENGLISH FCC CAUTION This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation This equipment has been tested and proven to comply with the limits for a class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipm
4. GLISH Deployment Example lt Small Hotspot Network Environment gt Nowadays wireless network service is common and popular in a hotspot network environment HSG260 provides wireless network service with authentication required for clients in Public Zone Wireless clients in the Public Zone and Private Zone are isolated from other wireless clients within the same zone when Station Isolation feature is enabled Using wireless instead of wired service helps hotspot owners to build network service quickly HSG260 supports two zones Private and Public In the Private Zone authentication is not required to access the network via wired and wireless Administrator can access the Web Management Interface WMI of HSG260 through the wired LAN port Waiters or waitresses can send orders back to the electrical menu system via wireless hand set devices In Public Zone by default Authentication Required is enabled so wired and wireless clients in Public Zone are required to get authenticated successfully before surfing the Internet AN The switches deployed under HSG260 must be Layer 2 switches only Configuration Steps Step 1 Configure Wireless Band for the Wireless interface gt Click Main Menu in the homepage Click the System menu then Zone Configuration tab gt Select a desired wireless band from Band drop down list Copyright 4IPNET INC All rights reserved 16 4ipnet Quick Installation Guide HSG260 Wireless Hotspot Gatew
5. SG260 2 gt Click Apply at the bottom of this page Wireless Settings RF1 VAP 2 192 168 11 100 Enabled VAP Status Enable Disable Basic Security Security Type None Beacon Interval 100 25 500ms RTS Threshold 2346 1 2346 Fragment Threshold 2346 256 2346 Advanced Broadcast SSID Enable Disable Station Isolation O Enable Disable WMM amp Enable Disable IGMP Snooping Enable Disable Copyright 4IPNET INC All rights reserved 18 4ipnet Step 4 Configure ESSID for Private Zone gt Enter a desired ESSID for Private Zone in Wireless Settings HSG260 1 Note Private Zone ESSID is not broadcasted by default but can be Enabled gt Select a desired Security Type for Private Zone for security enhancement if needed gt Click Apply at the bottom of this page Service Zone Name Private Public Basic Security Advanced Applied Policy Default Authen Service Zone Settings IP Address IPv6 Address Network Alias N A N A 4 DHCP Pool 192 168 1 1 192 168 1 100 192 168 11 1 192 168 11 100 Wireless Settings RF1 VAP 1 Option Policy 1 192 168 1 254 Disabled N A Policy 1 192 168 11 254 Server 1 N A VAP Status ESSID Security Type Beacon Interval RTS Threshold Fragment Threshold Broadcast SSID Station Isolation WMM IGMP Snooping Enable HSG260 1 Step 5 Confirm Configuration and Res
6. ation Contact your local regulatory authority for compliance Taiwan NCC Statement ri NCC ZR SERERE E ERBA SUE UU TOSS a SZ RRA RR FERRET ATI RCE FEES Se A SEE SER DIDI E BT iz SES EH ESSET ZTE RIB RHR EE A b FIAT ESCALA EB HG ROSSER CT HER S er BUR Aeg ze BAU TIRI 75 EHE ABER AA e HIDE Er gt FSR ALE ESR ZERI gt ETA BRIAR ISR SS Gs BCLS BEE Be ee Pee H a DE RS a ZIE Copyright 4IPNET INC All rights reserved iii 4ipnet Quick Installation Guide HSG260 Wireless Hotspot Gateway ENGLISH Preface The HSG260 is the most economical and feature rich Wireless Hotspot Gateway targeting mini size stores that want to provide small single point wireless Internet access service HSG260 is a perfect choice for beginners to run hotspot businesses It does not cost much compared to buying a pile of equipments nor does it take the skills of an expert to glue multiple applications out of multiple freeware Feature packed for hotspot operation HSG260 comes with built in 802 11 n b g MIMO access point web server and web pages for clients to login easy logo loading for branding a hotspot store simple user visitor account management tool payment plans multiple credit card payment gateways traffic logs IP sharing and etc HSG260 also brings in an extra advantage the wall mountable dust proof IP50 metal housing This Quick Installation Guide provides ins
7. ay ENGLISH 7 Logout Overview Service Zone Settings LAN Port A Applied Policy Poli IP Address Service Zone dai tid Network DHCP I O Mapping WENT Name Default Authen Alias Poo iex IPv6 Address suus Policy 1 ome 192 168 1 254 DE 192 168 1 1 Pump 192 168 1 100 Configure Disabled Enabled Palicy 1 168 11 254 JL JLeJLo Public 192 168 11 1 192 168 11 100 Enabled RF Card RF Cardi Band 802 119 802 11n pure 11n Short Preamble Enabled Disabled Short Guard Interval Enabled Disabled Channel Width 20MHz Channel Auto 7 Max Transmit Rate Auto Transmit Power Medium gt DTIM Period 1 1 255ms ACK Timeout 100 0 255ms Copyright 4IPNET INC All rights reserved 17 4ipnet Quick Installation Guide HSG260 Wireless Hotspot Gateway ENGLISH Step 2 Configure Public Zone Settings gt gt Click the System menu Click the Zone Configuration tab Click Configure button of Public Applied Policy Service Zone Name Default Authen Option Policy 1 Private Disabled Policy 1 Public Server 1 Service Zone Settings LAN Port IP Address Mappin ER DHCP Pool Details IPv6 Address Status 192 158 1 254 S Le L JL J 192 158 1 1 sc N A 192 168 1 100 Configure N A Enabled 192 168 11 254 La T 192 168 11 1 N A Step 3 Configure ESSID for Public Zone gt Enter a desired ESSID for Public Zone in Wireless Settings H
8. dmin Y Logout 7 Help Setup Wizard Quick Links System a Main Menu Overview To logout simply click Logout at the upper right hand corner of the Note interface to return to the Administrator Login Page Copyright 4IPNET INC All rights reserved 6 4ipnet Quick Installation Guide HSG260 Wireless Hotspot Gateway ENGLISH Common Settings lt Setup Wizard gt HSG260 provides a Setup Wizard for quick configuration To quickly configure HSG260 by using the Setup Wizard click on the Setup Wizard button to start the configuration process Username admin Password sesso Step 1 General e Enter a new administrator s password in the New Password field and re enter it again in the Verify Password field a maximum of 20 characters and no spaces allowed in between e Select an appropriate time zone from the Time Zone drop down list box and enter the URL of a valid NTP server to set up the system time e Client s browser will be redirected after logging into the system successfully The redirected page can be assigned instead of the default setting of client s browser by enabling Portal URL and configuring a desired one e Click Next to continue Copyright 4IPNET INC All rights reserved 7 4ipnet Quick Installation Guide HSG260 Wireless Hotspot Gateway ENGLISH ft Home Logout Setup Wizard Step 1 General Step 1 It is recommended to change administrator s us x a i
9. e installed and operated with a minimum distance of 20 centimeters between the radiator and your body Copyright 4IPNET INC All rights reserved ii 4ipnet Quick Installation Guide HSG260 Wireless Hotspot Gateway ENGLISH CE CAUTION Declaration of Conformity with Regard to the 1999 5 EC R amp TTE Directive for European Community Switzerland Norway Iceland and Liechtenstein Model HSG260 For 2 4 GHz radios the device has been tested and passed the requirements of the following standards and hence fulfills the EMC and safety requirements of R amp TTE Directive within the CE marking requirement Radio EN 300 328 EMC EN 301 489 1 EN 301 489 17 e EMC EN 55022 Class B EN 55024 A1 A2 including the followings EN 61000 3 2 EN 61000 3 3 EN 61000 4 2 EN 61000 4 3 EN 61000 4 4 EN 61000 4 5 EN 61000 4 6 EN 61000 4 1 1 e Safety EN 60950 1 A11 Caution This declaration is only valid for configurations combinations of software firmware and hardware provided and supported by 4ipnet Inc The use of software or firmware not provided and supported by 4ipnet Inc may result in the equipment no longer being compliant with the regulatory requirements European standards dictate maximum radiated transmit power of 100mW EIRP and frequency range 2 400 2 4835 GHz This equipment is intended to be used in all EU and EFTA countries Outdoor use may be restricted to certain frequencies and or may require a license for oper
10. ent generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment This device meets the government s requirements for exposure to radio waves This device is designed and manufactured not to exceed the emission limits for exposure to radio frequency RF energy set by the Federal Communications Commission of the U S Government The device contains a low power transmitter which will send out Radio Frequency RF signal when transmitting This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment This equipment should b
11. lient device access any URL and then the default User Login Page will appear 3 Enter the Username and Password of an on demand account previously generated via Setup Wizard e g testuser ondemand as the Username and testuser as the Password then Click Submit 4ipnet User Login Page Welcome To User Login Page Please Enter Your Name and Password to Sign In Username testuser ondemand Password 00000006 Remember Me Submit Clear Credit Balance Copyright The postfix can be omitted only when the default authentication option is used For example ONDEMAND is the default authentication option at this system therefore you may enter either testuser or testuser ondemand in the Username field Note Copyright 4IPNET INC All rights reserved 14 4ipnet Quick Installation Guide HSG260 Wireless Hotspot Gateway ENGLISH Congratulations The Login Success Page will appear after a client has successfully logged into HSG260 and has been authenticated by the system The appearance of Login Success Page means that HSG260 has been installed and configured properly 4ipnet Login Success Page Welcome testuser ondemand Credit Balance 23 43 11 Please be noticed that closing Login Success Page will force clients to Note log out HSG260 Copyright 4IPNET INC All rights reserved 15 4ipnet Quick Installation Guide HSG260 Wireless Hotspot Gateway EN
12. n server shall be configured HSG260 supports 4 kinds of authentication servers including Server 1 LOCAL Server 2 RADIUS Server 3 RADIUS and On demand ONDEMAND e By default the Default Auth Server is ONDEMAND e Use default or set your desired Postfix apply a Policy if needed e An On demand account can be created from a default billing plan and added to the database via the Create button If On demand accounts are not required click Next to go directly to Step 4 However it is recommended to create one account in order to verify the system s readiness upon completion of this Setup Wizard Copyright 4IPNET INC All rights reserved 10 4ipnet Quick Installation Guide HSG260 Wireless Hotspot Gateway ENGLISH Creating an On demand Account Plan Account Type 1 Duration time UsernamefPassword Creation System created Activation Time From account creation time Elapsed Time 4 houris Total Price O Reference o Add a reference related to this account for example the customers name External ID doo we an external IG such as Library ID Ma Please confirm the information and press Create button to create an account Welcome rvm6Gondemand Plan Account Type 1 Duration time Elapsed Time Valid for 4 n elapsed memes tema ESSID H5G260 2 Shared Wireless Key None Open System Your account is activa
13. nfigure related setting In addition Band Channel and ESSID of wireless interface can be configured in this step of Setup Wizard as well e Click Next to continue fa Home Logout Setup Wizard Step 2 WAN and Wireless Interfaces Interface WAN Wireless Band 802 11g n Channel ESSID Public HSG260 2 sa NNLLA HSG260 supports two Virtual Access Points one under Private zone and one under Public zone with ESSID HSG260 1 and HSG260 2 respectively by default The ESSID for VAP under Private is not Note broadcasted by default Detailed configurations for these two VAP can be performed under Main Menu gt gt System gt gt Zone Configuration Copyright 4IPNET INC All rights reserved 9 4ipnet Quick Installation Guide HSG260 Wireless Hotspot Gateway ENGLISH Step 3 Authentication Settings for Public Zone e For public zone by default authentication is enabled authentication can be enabled or disabled Clients shall log in the system before using network service if Auth Required is enabled f Home Logout Setup Wizard Step 3 Authentication Settings for Public Zone Auth Required Enable Disable Default Auth Server Ondemand ONDEMAND v On demand User Authentication Settings Postfix ondemand Policy Policy 4 v On demand Account Quick Creation Optional When authentication is enabled a default authenticatio
14. onfiguration Upon the completion of hardware installation HSG260 can be configured through a PC by using its web browser with JavaScript enabled such as Internet Explorer version 6 0 Default LAN interface IP address LAN1 amp LAN2 192 168 1 254 are mapped to Private Zone no authentication required for users LANS3 amp LANA 192 168 11 254 are mapped to Public Zone authentication required for users The instructions below are illustrated with the administrator PC Note connected to LAN1 Steps 1 Once the hardware installation is complete set DHCP in TCP IP settings of the administrator PC to Obtain an IP address automatically Connect the PC to the LAN1 Port of HSG260 An IP address will be assigned to the PC automatically via the HSG260 built in DHCP server 2 Launch a web browser to access the web management interface of HSG260 by entering https 192 168 1 254 or http 192 168 1 254 in the address field 2 4ipnet Windows Internet Explorer Di y UE https 1 192 169 1 254 File Edit View Favorites Tools Help Note https is used for a secured connection 3 The following Administrator Login Page will then appear Enter admin the default value in the Username and Password fields and then click Login to log in Copyright 4IPNET INC All rights reserved 5 4ipnet Quick Installation Guide HSG260 Wireless Hotspot Gateway ENGLISH Username a
15. r HSG260 is usually at the center of your wireless network 2 To supply power over to HSG260 a Connect the DC power adapter to the HSG260 power socket on the front panel Please only use the power adapter supplied with the HSG260 4 package Using a different power adapter may damage this system 3 Connect HSG260 to your outbound network device Connect one end of the Ethernet cable to the WAN port of HSG260 on the rear panel Depending on the type of Internet service provided by your ISP connect the other end of the cable to the ATU Router of an ADSL a cable modem a switch or a hub The WAN LED indicator should be ON to indicate a proper connection 4 Connect HSG260 to your network device Connect one end of the Ethernet cable to the LAN1 port of HSG260 on the rear panel Connect the other end of the cable to a PC for configuring the system The LAN1 LED indicator should be ON to indicate a proper connection HSG260 has two virtual zones Private and Public which are mapped to Note LAN1 LAN 2 192 168 1 254 and LAN3 LAN4 192 168 11 254 respectively Now the hardware installation is completed To double verify the wired connection between HSG260 and your A switch router hub please check the LED status indication of these network devices Copyright 4IPNET INC All rights reserved 4 4ipnet Quick Installation Guide HSG260 Wireless Hotspot Gateway ENGLISH Getting Started HSG260 supports web based c
16. t please follow the Connection Guide of HSG260 Ticket Generator after you have installed and configured your HSG260 For further information on HSG260 WTG HSG260 WTG2 please refer to Appendix G of the User s Manual P N 21020120817 Copyright 4IPNET INC All rights reserved 20
17. tart 100 2346 2346 Enable amp Enable Disable Mone Y Enable Disable Enable amp Disable gt Click Restart once all configurations are done You should resta Copyright 4IPNET INC All rights reserved E SVESLBITI ED aCll ale 19 2 Disable 5 Disable Quick Installation Guide HSG260 Wireless Hotspot Gateway ENGLISH LAN Port Mapping Details Status Enabled ee Tolo Configure Enabled 25 500ms 1 2246 256 2346 e changes mestart Te NEL 4ipnet Quick Installation Guide HSG260 Wireless Hotspot Gateway ENGLISH Step 6 Restart the System A confirmation message of Do you want to restart the system will appear Click YES to start the restarting process A confirmation dialog box will then pop out Click OK to continue eS 35 e A B System Users Network Status Password Change Backup amp Restore System Upgrade Restart Network Utilities Do you want to RESTART the system AN Please do not interrupt the system during the restarting process For further configuration and information please refer to the User s Manual If you have purchased 4ipnet s Network Ticket Generator and wish to incorporate it into your Hotspot please follow the Connection Guide of Network Ticket Generator after you have installed and configured your HSG260 If you have purchased 4ipnet s POS Printer and wish to incorporate it into your Hotspo
18. te Administrator s Password appropriate time zone and MTP server far the New Password essee E system Verify Password eese P Time Time Zone GMT 08 00 Talpel NTP Server tock usno navy mil e g tock usno navy mil Portal URL Status OEnable Disable IRttp www google com HSG260 supports NTP time synchronization If NTP is the option selected it is strongly recommended to make sure the NTP server is reachable and alive Step 2 WAN and Wireless Interfaces For setting up both wired WAN and Wireless LAN interfaces e Select a proper type of Internet connection for WAN interface from the following three available connections Static Dynamic or PPPoE Your ISP or network administrator can advise on the connection type available to you Below depicts an example for Dynamic Copyright 4IPNET INC All rights reserved 8 4ipnet Select a connection type for WAN interface and configure related setting In addition interface can be configured in this step af Setup Wizard as well Quick Installation Guide HSG260 Wireless Hotspot Gateway ENGLISH fi Home Logout Setup Wizard Step 2 WAN and Wireless Interfaces Interface WAN Wireless Q Static Use the following IP settings 9 Dynamic IP settings assigned automatically PPPoE e Click Wireless radio button e Select desired wireless Band Channel and ESSID for public zone Select a connection type for WAN interface and co
19. ted at 2011 10 06 13 52 Your first time login must be done before 2011 10 06 15 52 The account will be expired in 4 hours after account activation Thank You Send to POS Note To make a better print out ticket you may need to cofigure the browser settings for example Page Setup as well as the printer settings for example Preferences before printing out the page Copyright 4IPNET INC All rights reserved Il 4ipnet Quick Installation Guide HSG260 Wireless Hotspot Gateway ENGLISH e After you have printed out the ticket or noted down the Username and Password information Close the account information window return to Setup Wizard and click Next to continue 1 HSG260 supports four authentication servers with internal authentication databases LOCAL gt ONDEMAND and external authentication databases RADIUS 2 The complete name format is userid postfix Userid is the username and postfix is used by the system to determine the Note authentication server 3 For hotspot deployments it is recommended to use ONDEMAND For details regarding other authentication databases please refer to the user manual 4 For Policy and Billing Plan configuration please refer to the user manual for detail Step 4 Confirm and Restart e Click Finish to save current settings and restart the system ft Home Logout 7Help Setup Wizard Confirm and Restart Please press Finish button and restart the system
20. tructions and reference materials for getting started with HSG260 Package Contents HSG260 x 1 7 Detachable Antenna x 2 Quick Installation Guide x 1 CD ROM with User Manual and QIG x 1 Console Cable x 1 Ethernet Cable x 1 Power Adapter DC 5V x 1 A It is recommended to keep the original packing material for possible future shipment when repair or maintenance is required Any returned product should be packed in its original packaging to prevent damage during delivery oor OD Copyright 4IPNET INC All rights reserved l 4ipnet Quick Installation Guide HSG260 Wireless Hotspot Gateway ENGLISH System Overview Front Panel A PO CL E un ss 00 uD Quick Print Press this button to create an on demand account from billing plan 1 and print button out through console Need to work with a POS printer connected via console port WES button Press and hold over 5 seconds to initiate Master WES process Press and release to initiate Slave WES process Power LED On indicates power on Status LED On indicates the system ready Wireless LED On indicates wireless network interface is ready for service WAN LED On indicates that WAN uplink connected T1 LAN1 4 LED Indicates the connection status of each LAN USB LED Indicates the status of USB connection USB port reserved for future use WES LED For indicating WDS connection status Master Press for more Slave Press once and than
Download Pdf Manuals
Related Search