Home

Nport W2004 User Manual

Contents

1. Address Translation MIB TCP MIB SNMP MIB AtNetAddress tcpRetransSegs snmpInTotalSetVars tepConnState snmpInGetRequests tcpConnLocalAddress snmpInGetNexts tepConnLocalPort snmpInSetRequests tepConnRemAddress snmpInGetResponses tepConnRemPort snmpInTraps tcpInErrs snmpOutTooBigs tcpOutRsts snmpOutNoSuchNames snmpOutBad Values snmpOutGenErrs snmpOutGetRequests snmpOutGetNexts snmpOutSetRequests snmpOutGetResponses snmpOutTraps snmpEnableAuthenTraps The Input Signal Table The Output Signal Table rs232InSigTable rs2320utSigTable rs232InSigEntry rs232OutSigEntry rs232InSigPortIndex rs232OutSigP ortIndex rs232InSigName rs2320utSigName rs232InSigState rs2320utSigState A 3 Well Known Port Numbers This appendix is for your reference Listed below are Well Known Port Numbers that may cause network problems if you configure NE 4000T for the same port Refer to RFC 1700 for Well Known Port Numbers or refer to the following introduction from IANA The port numbers are divided into three ranges the Well Known Ports the Registered Ports and the Dynamic and or Private Ports e The Well Known Ports range from 0 through 1023 e The Registered Ports range from 1024 through 49151 e The Dynamic and or Private Ports range from 49152 through 65535 The Well Known Ports are assigned by IANA and on most systems can only be used by system processes or by programs executed b
2. Exit Add Remove Appl Setting No COM Port IP Address Command Port COM2 192 168 126 254 2 COM3 192 168 126 254 951 967 3 COM 192 168 126 254 950 966 4 COM8 192 168 126 254 951 967 5 COM9 192 168 126 254 952 968 6 COM10 192 168 126 254 953 969 In the Basic Setting panel use the COM Number drop down list to select a COM number for the NPort s first serial port Check mark the Auto Enumerating COM Number for Selected Ports checkbox to automatically assign the next available COM number to the second serial port Note that ports that are in use will be labeled accordingly COM Port Setting Port Number 1 Port s Selected 1st port is Port 1 Basic Settings Advanced Settings Serial Parameters COM Number coma current in use y X Cancel Click on the Advanced Setting tab to modify Tx Mode FIFO and Flash Flush Tx Mode Hi performance mode is the default for Tx mode When the driver finishes sending data to the NPort W2004 the driver will issue a Tx Empty response to the program 6 13 NPort W2004 User s Manual Installing and Configuring the Software Under classical mode the driver will not notify the user s program that Tx transmission is finished until all Tx data has been sent out from the NPort W2004 This ODE will cause lower throughput Classical mode is recommended if you want to ensure that all data is sent out before further processing FIFO If the
3. Maintenance Firmware Upgrade Click on Firmware Upgrade to upgrade the firmware E Main Menu E Overview A Wizard Firmware Upgrade Firmware Upgrade Time Settings A Select Firmware File E Network Settings E Serial Port Settings SJ System Management Misc Network Settings 4 Auto Warning Settings System Status Maintenance Firmware Upgrade E Configuration Import 2 Configuration Export 2 Load Factory Default 1 Change Password E Restart Ports L Restart System E Logout Select the correct firmware file and then click on Submit to load the new firmware into the NPort W2004 s memory 5 31 NPort W2004 User s Manual Web Console Configuration SJ Main Menu E Overview 4 wizard Firmware Upgrade Firmware Upgrade E Time Settings HE Network Settings Select Firmware File W2004 binary firmware NPW2004_ 2 8 ron 4 Serial Port Settings Y System Management Misc Network Settings Auto Warning Settings 4 System Status EXA Maintenance i Firmware Upgrade Configuration Import Configuration Export Load Factory Default Change Password Restart Ports i Restart System E Logout Configuration Import Select the a configuration file and then click on Submit to load the configuration settings into the NPort W2004 J Main Menu Configuration Import A Overview
4. System Management Misc Network Settings Console Settings J Main Menu Overview wizard Time Settings HE Network Settings 1 Serial Port Settings EXA System Management EX Misc Network Settings a Accessible IP List A TCP Alive Check Time Console Settings lt J E E Enable HTTP console Enable HTTPS console Enable TELNET console Enable SSH console Submit Cancel Use this screen to enable or disable HTTP console HTTPS console TELNET console and SSH console 5 21 NPort W2004 User s Manual Web Console Configuration Accessible IP List J Main Menu A Overview Wizard 4 Time Settings El Network Settings O Console list Enable HC Serial Port Settings 23 System Management J Misc Network Settings s st TCP Alive Check Time 2 Serial Data Logging SNMP Agent Auto Warning Settings EQ System Status Maintenance Logout 0 N oo hh Y N Accessible IP List IP Address Submit Cancel NPort W2004 uses an IP address based filtering method to control access to itself Netmask Netmask Accessible IP Settings allows you to add or block remote host IP addresses to prevent unauthorized access Access to NPort W2004 is controlled by IP address That is if a host s IP address is in the accessible IP table
5. The following files will be extracted README moxattyd c source code moxattyd cf an empty configuration file Makefile makefile VERSION TXT fixed tty driver version 6 20 NPort W2004 User s Manual Installing and Configuring the Software Step 4 Compile and Link For SCO UNIX make SCO For UnixWare 7 make svr5 For UnixWare 2 1 x SVR4 2 make svr42 Step 5 Modify the configuration The configuration used by the moxattyd program is defined in the text file moxattyd cf which is in the same directory that contains the program moxattyd You may use vi or any text editor to modify the file E g ttypl 192 168 1 1 950 For more configuration information look at the file moxattyd cf which contains detailed descriptions of the various configuration parameters NOTE The Device Name depends on the OS See the Device Naming Rule section for more information Step 6 To start the moxatt yd daemon after system bootup add an entry into etc inittab with the tty name you configured in moxattyd cf E g ts 2 respawn usr etc moxattyd moxattyd t 1 This completes the installation and configuration of MOXA TTY Device Naming rule For UnixWare 7 UnixWare 2 1 x and SVR4 2 use pts n For all other UNIX operating systems use ttyp n Starting moxattyd Execute the command init q or reboot your UNIX operating system Adding an additional server
6. Overview Installing NPort COM Driver Intalling NPort Search Utility Configuring NPort COM Driver Configuring NPort Search Utility Real TTY and Fixed TTY Installation Upgrading the Firmware DODODODOODO NPort W2004 User s Manual Installing and Configuring the Software Overview The Documentation amp Software CD included with your NPort W2004 is designed to make the installation and configuration procedure easy and straightforward This auto run CD includes the NPort COM Driver for COM mapping NPort Search Utility to broadcast search for all NPort W2004 accessible over the network User s Manual and firmware upgrade utility Installing NPort COM Driver 1 Click on the INSTALL COM Driver button in the NPort Installation CD auto run window to install the NPort W2000 Series COM Driver NPort Installation CD Wireless Serial Device Servers Software CD Ver1 1 Press the INSTALL COM Driver button to install NPort COM Driver NPort COM Driver can be installed under Windows9x MEINT 2000 XP 2003 systems 2 Once the installation program starts running click on Yes to proceed 3 Click on Next when the Welcome window opens to proceed with the installation NPort W2004 User s Manual Installing and Configuring the Software 4 Welcome to the NPort Windows Driver Manager Setup Wizard This will install NPort Windows Driver Manager Ver0 1 3 on pour computer It is recommended that you close
7. lt lt Main Menu gt gt 1 Time Settings 2 Network Settings 3 Serial Port Settings 4 System Management q Quit 3 Type 2 to select Network settings and then press Enter Host Name NPW2004 20 Model Name NPort WO04 US LAN MAC Address 00 90 e8 93 04 36 WLAN MAC Address N A Serial No 20 Firmware Version 0 0 1 1 beta6 lt lt Main Menu gt gt 1 Time Settings Network Settings Serial Port Settings 2 3 4 System Management q Quit Key in your selection 2 NPort W2004 User s Manual Initial IP Configuration 4 Type 2 to select Ethernet Configuration and then press Enter lt lt Main Menu gt gt General Settings Ethernet Configuration WLAN Configuration View Settings Back to the Main Menu Quit Key in your selection 2 Type 2 to select IP Address and then press Enter then use the Backspace key to erase the current IP address type in the new IP address and then press Enter lt lt Main Menu gt Network Settings gt Ethernet Configuration gt gt IP Configuration IP Address Netmask Gateway View Settings Back to Main Menu Quit Key in your selection 2 IP Address 192 168 126 254 Serial Console 19200 n 8 1 We suggest using MOXA PComm Terminal Emulator which can be downloaded free of charge from www moxa com to carry out the configuration procedure 1 Connect NPort W2004 s RS 232 console port directly to your computer s male
8. wizard EER Time Settings s E Import configuration from Network Settings 1 3 Serial Port Settings F System Management 4 Misc Network Settings Auto Warning Settings System Status EZ Maintenance i Firmware Upgrade A Configuration STATE 2 Load Factory Default Change Password E Restart Ports Restart System E Logout Configuration Export Click on the Download button and then select the file that you would like to export the current configuration to 5 32 NPort W2004 User s Manual Web Console Configuration Lao E Configuration Export re verview Wizard i RET ERE 9 Time Settings i q Download Configuration File HE Network Settings HC Serial Port Settings ES System Management 4 Misc Network Settings Auto Warning Settings System Status Ey Maintenance i Firmware Upgrade Configuration Import Load Factory Default i Change Password Restart Ports E Restart System Logout Load Factory Default Use this page to reset the NPort W2004 s settings to the factory default values Be aware that previous settings will be lost Choose one of the two options Reset to factory default excluding IP configuration or Reset to factory default and then click on Submit Choose the first option to retain the current IP address Netmask and Gateway address Total Solution fo Main Menu i 3 Load Factory Default 1 Overvie
9. Power Input 12 48 VDC Power Consumption 685 mA 12V 184 mA 48V 340 mA 24V Mechanical Specifications Material SECC sheet metal 1 mm Environmental Operating Temperature 0 to 60 C 32 to 140 F 5 to 95 RH Storage Temperature 20 to 85 C 4 to 185 F 5 to 95 RH Regulatory Approvals EMC FCC Class A CE Class A Safety UL CUL TUV Serial Port Pin Assignments 8 pin RJ45 Port RS 232 422 485 Pinouts Pin RS 232 RS 422 RS 485 RS 485 4 wire 2 wire 1 DSR 2 RTS TxD TxD 3 GND GND GND GND 4 TxD TxD TxD 5 RxD RxD RxD Data 6 DCD RxD RxD Data 7 CTS 8 DTR 1 4 Getting 2 Started This chapter includes information about installing NPort W2004 The following topics are covered in this chapter gt VV V V O Panel Layout LJ Connecting the Hardware Wiring Requirements Connecting the Power Connecting to the Network Connecting to a Serial Device LED Indicators NPort W2004 User s Manual Getting Started Panel Layout Reset button Power inputs Antenna Top View DIN Rail Mount o E E G a o Es S Signal Strength LEDs AO YY YY YY YY OT 8 pin RJ45 serial ports NPort W2004 Front View Side View Connecting the Hardware This section describes how to connect NPort W2004 to serial devices for first time testing purposes We cover
10. 1 to 65535 Forces the NPort W2004 s TCP IP protocol software to try to pack serial data received during the specified time into the same data frame 5 18 NPort W2004 User s Manual Web Console Configuration This parameter defines the time interval during which NPort W2004 fetches the serial data from its internal buffer If data is incoming through the serial port NPort W2004 stores the data in the internal buffer NPort W2004 transmits data stored in the buffer via TCP TP but only if the internal buffer is full or if the Force transmit time interval reaches the time specified under Force transmit timeout The optimal Force transmit timeout depends on your application but it must be at least larger than one character interval within the specified baud rate For example assume that the serial port is set to 1200 bps 8 data bits 1 stop bit and no parity In this case the total number of bits needed to send a character is 10 bits and the time required to transfer one character is 10 bits 1200 bits s 1000 ms s 8 3 ms Therefore you should set Force transmit to be larger than 8 3 ms so in this case it must be greater than or equal to 10 ms If you want to send a series of characters in the same packet the serial device attached to NPort W2004 should send that series of characters during a time interval less than the Force transmit timeout and the total length of data must be less than or equal to NPort W2004 s
11. A Serial Port Settings Na a Port 1 n H Port 2 Mode O Infrastructure Mode Ad hoc Mode aE Port 3 SSID default E Port 4 Channel H System Management Misc Network Settings _ H Auto Warning Settings WLAN Network Configuration NPort W2004 supports the IEEE 802 11b wireless network interface The supported IP configurations are static and dynamic DHCP Users can set up the IP configuration via the serial console or the Web Telnet consoles through the NPort s Ethernet 5 7 NPort W2004 User s Manual Web Console Configuration interface For detailed information about configuring IP configuration IP address Netmask and Gateway see the previous section Ethernet Configuration WLAN Wireless LAN You may choose from two different WLAN modes Infrastructure Mode and Ad hoc Mode which are illustrated in the following diagrams Ad hoc Mode In the following example two NPort W2004 devices establish an Ad hoc peer to peer relationship which means that they communicate with each other directly without going through an AP Access Point RS 232 E Flow meters 1 E Drives Infrastructure Mode In the following example the NPort W2004 communicates with the host computer via the AP The host computer connects to the AP via an Ethernet connection allowing serial data to be transmitted back and forth between the serial devices and host computer Host WA computer
12. Step 1 Modify the text file moxattyd cf to add an additional server User may use vi or any text editor to modify the file For more configuration information look at the file moxattyd cf which contains detailed descriptions of the various configuration parameters Step 2 Find the process id PID of the program moxattyd ps ef grep moxattyd Step 3 Update configuration of moxattyd program kill USR1 PID e g if moxattyd PID 404 kill USR1 404 This completes the process of adding an additional server 6 21 NPort W2004 User s Manual Installing and Configuring the Software Upgrading the Firmware You will need to use the NPort W2004 web browser utility to upgrade the firmware Type the NPort W2004 s IP address in your web browser s address box if you already know the IP address If you don t remember the IP address you can use the NPort Search Utility to locate the server and then double click on the server whose firmware you wish to upgrade Your browser should open automatically to the NPort s web utility page I Type the User Name and Password to login The defaults are both admin Z Login Microsoft Internet Explorer File Edit View Favorites Tools Help Q O x 2 2 O arh Se Favorites A Media AMARE Address E http 192 168 126 254 login asp Total Solution for Indu User Name admin Password essee Cancel Click on System Management gt Ma
13. WEP Mode is disabled When WEP Mode is enabled data packets will be encrypted before being sent You may select either 64 bit or 128 bit encryption WEP Key 1 2 3 4 For each of the four WEP Keys select either ASCII or HEX format and then enter the appropriate WEP Key The WEP Keys are used to help prevent data from being stolen as 1t is transmitted over public networks The WEP Key setting s for the NPort W2004 must be the same as the WEP Key settings for the AP 5 9 NPort W2004 User s Manual Web Console Configuration Serial Port Settings Serial port settings are configured by port Operation Modes The Serial Port parameters that appear in the right pane of the browser window when Serial Port Settings gt Port 1 2 3 4 gt Operation Modes is selected are dependent on which of the four operation modes is selected We consider each operation mode separately Real COM Mode Main Menu a X Operation Modes Overview a Wear Port Settings Time Settings tare a Network Settings Operation mode Real COM Mode E Serial Port Settings Z Max connection 1 1 4 Sy Port 1 _ Operation Modes Communication Param Data Packing aE Port 2 Delimiter 1 00 Hex Enable 9 Port 3 Delimiter 2 00 Hex LJEnable ie E Port 4 Force transmit lo lo 65535 ms l System Management y E a sy 3 Q i Apply the above settings to all serial
14. then the host will be allowed to access the NPort W2004 You can set up one of the following cases by setting the parameters accordingly e Only one host with a specific IP Address can access the NPort W2004 Enter the specific IP address e g 192 168 1 1 and enter 255 255 255 255 for Netmask e Hosts on the specific subnet can access the NPort W2004 Enter an IP address e g 192 168 1 0 and enter the Netmask e g 255 255 255 0 Note that this type of setting will allow access to all network hosts on a particular subnet e Any host can access the NPort W2004 Disable this function by un checking the Enable the accessible IP list checkbox Refer to the following table for more configration examples The following Allowable Hosts table gives five configuration examples Allowable Hosts IP Address Netmask Any host blank blank 192 168 1 120 192 168 1 120 255 255 255 255 192 168 1 1 to 192 168 1 254 192 168 1 0 255 255 255 0 192 168 0 1 to 192 168 255 254 192 168 0 0 255 255 0 0 192 168 1 1 to 192 168 1 126 192 168 1 0 255 255 255 128 192 168 1 129 to 192 168 1 254 192 168 1 128 255 255 255 128 5 22 NPort W2004 User s Manual Web Console Configuration TCP Alive Check Time Total Solution for Industrial Device J Main Menu f i 3 TCP Alive Check Time Overview A wizard NPort W2000 Series automatically closes the TCP connection if there is no TCP activity fr
15. 1 Operation Modes Port Settings Port 1 Operation mode UDP Mode x Data Packing A Operation Modes 00 Hex enable Communication Paramete Delimiter 2 00 Hex C Enable HS Port 2 Force transmit o ko 65535 ms Port 3 UDP Mode HA Port 4 Begin End Port System Management Destination IP address 1 4001 C Logout Destination IP address 2 4001 Destination IP address3 W 4001 Destination IP address 4 4001 Local listen port 4001 Al Cl Apply the above settings to all serial ports Submit Cancel Data Packing Delimiter 1 2 Setting Factory Default Necessity 00 to FF hex None Optional Once the NPort W2004 receives both delimiters through its serial port it immediately packs all data currently in its buffer and sends it to the NPort W2004 s Ethernet port A ATTENTION Delimiter 2 is optional If left blank then Delimiter 1 alone trips clearing of the buffer If the size of the serial data received is greater than 1 KB the NPort W2004 will automatically pack the data and send it to the Ethernet However to use the delimiter function you must at least enable Delimiter 1 If Delimiter 1 is left blank and Delimiter 2 is enabled the delimiter function will not work properly Force transmit Setting Factory Default Necessity 0 to 65535 ms 0 Optional 0 Disable force transmit timeout
16. Browser gt Accessing NPort W2004 s Homepage gt Time Settings Network Settings gt General Settings gt Ethernet Configuration gt WLAN Configuration Serial Port Settings gt Operation Modes gt Communication Parameters System Management gt Misc Network Settings gt Auto Warning Settings gt System Status gt Maintenance Logout NPort W2004 User s Manual Web Console Configuration Overview Configuring Your Browser Before opening your browser you need to enable cookies To enable your browser for cookies 1 Right click on your desktop Internet Explorer icon select Properties and then click on the Security tab Internet Properties 9300 Local intranet Trusted sites Restricted sites 2 Enable the three options shown in the figure below and then click on OK Security Settings Cookies Allow cookies that are stored on your computer O Disable Enable O Prompt Allow per session cookies not stored O Disable O Enable O Prompt 23 File download O Disable O Enable Y Cant deseas NPort W2004 User s Manual Web Console Configuration Accessing NPort W2004 s Homepage Use the NPort W2004 s IP address to access its homepage 1 Type 192 168 126 254 the default IP address in your browser s Address box use the correct IP address if different from the default and then press Enter 2 Input the password NPort W2004 allows only one user The usernam
17. If data is incoming through the serial port NPort W2004 stores the data in the internal buffer NPort W2004 transmits data stored in the buffer via TCP IP but only if the internal buffer is full or if the Force transmit time interval reaches the time specified under Force transmit timeout The optimal Force transmit timeout depends on your application but it must be at least larger than one character interval within the specified baud rate For example assume that the serial port is set to 1200 bps 8 data bits 1 stop bit and no parity In this case the total number of bits needed to send a character is 10 bits and the time required to transfer one character is 10 bits 1200 bits s 1000 ms s 8 3 ms Therefore you should set Force transmit to be larger than 8 3 ms so in this case it must be greater 5 11 NPort W2004 User s Manual Web Console Configuration than or equal to 10 ms If you want to send a series of characters in the same packet the serial device attached to NPort W2004 should send that series of characters during a time interval less than the Force transmit timeout and the total length of data must be less than or equal to NPort W2004 s internal buffer size The serial communication buffer size for NPort W2004 is 1 KB per port TCP Server Mode Main Menu A Overview A wizard E Time Settings 1 Network Settings J Serial Port Settings 23 Port 1 A Operation Modes i Commu
18. If you encounter this situation you may use one of the following two remedies 1 Wait until the signal becomes stronger or 2 Re survey the site and then restructure the WLAN components to ensure that the signal strength is always strong enough so that 2 or more signal strength LEDs are always lit 2 4 3 Initial IP Address Configuration When setting up your NPort W2004 for the first time the first thing you should do is configure the IP address Select one of the initial IP Address configuration methods to configure NPort W2004 s IP Address For more details about network settings see the Network Settings section from Chapter 5 Web Console Configuration This chapter covers the following topics Installation Procedure for First time Users Factory Default IP Address Telnet Console Serial Console 19200 n 8 1 Oooo NPort W2004 User s Manual Initial IP Configuration Installation Procedure for First time Users STEP 1 After removing NPort W2004 from the box use a cross over Ethernet cable to connect directly to your computers Ethernet port STEP 2 Attach the power adaptor to the NPort W2004 and then plug the adaptor into an electrical outlet STEP 3 Use the Web console to configure the NPort W2004 via the Ethernet port NOTE We recommend that you use the web console to configure NPort W2004 See Chapter 5 for instructions on how to use the web console Factory Default IP Address NPort W
19. MAC Address IP Address NPort W2004 US 00 90 8 93 04 36 192 168 126 254 2 The Searching window indicates the progress of the search Searching Searching for NPort Found 1 NPort s 4 second s left No Model MAC Address IP Address NPort W2004 US 00 90 E8 93 04 36 192 168 126 254 NPort W2004 User s Manual Installing and Configuring the Software 3 When the search is complete the NPort W2004 units that were located will be displayed in the NPort Search Utility window PS NPort Search Utility File Function Help F ES E ET Exit Search Search IP No Model MACAddress IP Address 1 NPort W2004 US 00 90 E8 93 04 36 192 168 126 254 4 To modify the configuration of the highlighted NPort W2004 click on the Console icon to open the web console 19 NPort Search Utility File Function Help 2 a py o Ext Search Search IP Locate Console i NPortw2004 US 00 90 8 93 04 36 192168 126 254 IP E Linux Real TTY and UNIX Fixed TTY Installation Installing the Linux Real TTY driver Procedure To map an NPort serial port to the host s tty port you need to 1 Setup NPort Make sure the IP configuration is ok and you can access the NPort ping telnet successfully and then configure the NPort serial port to Real COM Mode 2 Install driver files on the host Refer to Driver Files Installation below for details 3 Map the NPort seria
20. NPort exhibits a much poorer operation performance than when using the native COM1 port Once you have enabled the Fast Flush function you can check to see if there has been an improvement in performance 6 14 NPort W2004 User s Manual Installing and Configuring the Software d By default the optional Fast Flush function is disabled If you would like to enable this function double click on the COM ports that are mapped to the NPort and then select the Fast Flush checkbox You should find that when Fast Flush is enabled the NPort driver will work faster with PurgeComm COM Port Setting Port Number 1 Port s Selected 1st port is Port 1 Basic Settings Advanced Settings Serial Parameters The FIFO settings will overwrite the firmware setting TxMode HiPerfomance FIFO Enable y Jv Fast Flush Only Flush Local Buffer ly All Selected Ports X Cancel NPort W2004 User s Manual Installing and Configuring the Software 9 The Serial Parameter settings shown in the following figure are the default settings when the NPort W2004 is powered on However the program can redefine the serial parameters to different values after the program opens the port via Win 32 API COM Port Setting Port Number 1 Ports Selected 1st port is Port 1 Basic Settings Advanced Settings Serial Parameters These options will be saved on registry and used on few applicatio
21. RS 232 serial port From the Windows desktop click on Start gt Programs gt PComm Lite gt Terminal Emulator When the PComm Terminal Emulator window opens first click on the Port Manager menu item and select Open or click on the Open icon ER PComm Terminal Emulator Profile Port Manager Help NPort W2004 User s Manual Initial IP Configuration 4 The Property window opens automatically From the Communication Parameter page select the appropriate COM port for the connection COM1 in this example and 19200 for Baud Rate 8 for Data Bits None for Parity and 1 for Stop Bits 5 From the Property window s Terminal page select ANSI or VT100 for Terminal Type and click on OK If you select Dumb Terminal as the terminal type some of the console functions especially the Monitor function may not work properly Jo Local Echo 6 Input the password when prompted 7 Start by configuring the IP address under Network Settings Refer to the Telnet Console section for instructions on how to configure the rest of the IP settings 3 5 4 Choosing the Proper Operation Mode In this chapter we describe the various NPort W2004 operation modes The options include an operation mode that uses a driver installed on the host computer and operation modes that rely on TCP IP socket programming concepts After choosing the proper operation mode in this chapter refer to Chapter 5 for detailed configurati
22. Wiring Requirements Connecting the Power Connecting to the Network Connecting to a Serial Device and LED Indicators 2 2 NPort W2004 User s Manual Getting Started Wiring Requirements A ATTENTION Safety First Be sure to disconnect the power cord before installing and or wiring your device Wiring Caution Calculate the maximum possible current in each power wire and common wire Observe all electrical codes dictating the maximum current allowable for each wire size If the current goes above the maximum ratings the wiring could overheat causing serious damage to your equipment Temperature Caution Be careful when handling the device When plugged in the device s internal components generate heat and consequently the casing may feel hot to the touch You should also pay attention to the following items e Use separate paths to route wiring for power and devices If power wiring and device wiring paths must cross make sure the wires are perpendicular at the intersection point NOTE Do not run signal or communication wiring and power wiring in the same wire conduit To avoid interference wires with different signal characteristics should be routed separately e Use the type of signal transmitted through a wire to determine which wires should be kept separate The rule of thumb is that wiring that shares similar electrical characteristics can be bundled together e Keep input wiring and output wiring separa
23. as remote COM ports for your PC host Use the following steps to map the COM ports 1 Click on Start gt Nport Windows Driver Manager gt NPort COM Mapping Utility to start the COM mapping utility FS NPort Windows Driver Manager PA NPortCOM Mpaaing Utility y 2 Uninstall 2 Click on the Add icon 4 NPort Windows Driver Manager File COM Mapping View Help F gh ih y A E Exit d Remove Apply Undo Setting COM Port IP Address Mode NPort W2004 User s Manual Installing and Configuring the Software 3 Click on Rescan to search for NPort device servers select the server you would like to map COM ports to and then click on OK Add NPort NPort W2004 US 00 90 E8 93 04 36 192 168 126 254 C Input Manually NPort IP Address 1st Data Port 1st Command Port Total Ports X Cancel 6 10 NPort W2004 User s Manual Installing and Configuring the Software 4 Alternatively you can select Input Manually and then input the NPort IP Address 1 Data Port 1 Command Port and Total Ports for the NPort W2004 that you would like to map COM ports to Click on OK to proceed to the next step Add NPort Select From List af Select All No Model MAC Address IP Address 1 NPort W2004 US 00 90 8 93 04 36 192 168 126 254 NPort IP Address 1st Data Port 850 1st Command Port 1966 Total Ports f X Cancel 6 11 NPort W2004 User s Manual Inst
24. ports 4 Misc Network Settings 13 Auto Warning Settings System Status Submit Cancel Port 1 2 3 4 Max connection Setting Factory Default Necessity 1 2 3 4 1 Required Max connection is usually used when the user needs to receive data from different hosts simultaneously The factory default is 1 In this case only one specific host can access this port of the NPort W2004 and the Real COM driver on that host will have full control over the port Max connection 1 Allows only 1 host s Real COM driver to open the specific NPort W2004 serial port Max connection 2 to 4 Allows 2 to 4 host s Real COM drivers to open the specific NPort W2004 serial port at the same time When multiple hosts Real COM drivers open the serial port at the same time the COM driver only provides a pure data tunneling without control ability Application software that is based on the COM driver will receive a driver response of success when the software uses any of the Win32 API functions The firmware will only send the data back to the driver on the host Data will be sent first in first out when data comes into the NPort W2004 from the Ethernet interface 5 10 NPort W2004 User s Manual Web Console Configuration A ATTENTION When Max connection is set to 2 3 or 4 NPort W2004 will use a multi connection application i e 2 3 or 4 hosts are allowed access to the port at the same time When usi
25. properly if it is not configured correctly NPort W2004 SMTP AUTH supports LOGIN PLAIN CRAM MDS RFC 2554 SNMP Trap Total Solution for Industrial Devi Main Menu ES ra Overview p Wizard SNMP trap receiver IP Trap version Trap Community String C Time Settings 1 Ov1 Ovzc alert le Network Settings 2 O a alert H Serial Port Settings 5 ia z lale EA System Management panas E Misc Network Settings 4 O vi O v2c lalert 23 Auto Warning Settings A Event Settings E E mail Alert as E E ULA A eee SNMP trap receiver IP or domain name Setting Factory Default Necessity IP address or Domain Name None Optional System Status WLAN Status The WLAN Status page lists Mode SSID Country Code Channel Link Status Signal Strength Connection Speed WEP Mode IP Configuration IP Address and Netmask as shown in the following figure Main Menu F gt WLAN Status E Overview E Wizard WLAN Status Time Settings E Network Settings E Serial Port Settings EY System Management E Misc Network Settings Auto Warning Settings Country Code Network Mode SSID Channel Link Status Signal Strength Connection Speed US Infrastructure Mode default N A Not Connected 0 O Mbps Disable Static 192 168 127 254 255 255 255 0 EA System Status WEP M
26. sends it to the NPort W2004 s Ethernet port A ATTENTION Delimiter 2 is optional If left blank then Delimiter 1 alone trips clearing of the buffer If the size of the serial data received is greater than 1 KB the NPort W2004 will automatically pack the data and send it to the Ethernet However to use the delimiter function you must at least enable Delimiter 1 If Delimiter 1 is left blank and Delimiter 2 is enabled the delimiter function will not work properly Force transmit Setting Factory Default Necessity 0 to 65535 ms 0 Optional 0 Disable force transmit timeout 1 to 65535 Forces the NPort W2004 s TCP IP protocol software to try to pack serial data received during the specified time into the same data frame This parameter defines the time interval during which NPort W2004 fetches the serial data from its internal buffer If data is incoming through the serial port NPort W2004 stores the data in the internal buffer NPort W2004 transmits data stored in the buffer via TCP TP but only if the internal buffer is full or if the Force transmit time interval reaches the time specified under Force 5 16 NPort W2004 User s Manual Web Console Configuration transmit timeout The optimal Force transmit timeout depends on your application but it must be at least larger than one character interval within the specified baud rate For example assume that the serial port is set to 1200 bps 8 data bits 1
27. starts listening for another host s TCP connection This parameter defines the maintenance status as Closed or Listen for the TCP connection The connection is closed if there is no incoming or outgoing data through the serial port during the specific Inactivity time If the Inactivity time is set to 0 the current TCP connection is kept active until a connection close 5 15 NPort W2004 User s Manual Web Console Configuration request is received Although Inactivity time is disabled the NPort W2004 will check the connection status between the NPort W2004 and remote host by sending keep alive packets periodically If the remote host does not respond to the packet NPort W2004 assumes that the connection was closed down unintentionally NPort W2004 will then force the existing TCP connection to close ATTENTION The Inactivity time should be set at least larger than that of Force transmit timeout To prevent the unintended loss of data due to the session being disconnected it is highly recommended that this value is set large enough so that the intended data transfer can be completed ATTENTION Inactivity time is ONLY active when TCP connect on is set to Any character Data Packing Delimiter 1 2 Setting Factory Default Necessity 00 to FF hex None Optional Once the NPort W2004 receives both delimiters through its serial port it immediately packs all data currently in its buffer and
28. 2004 is configured with the following default IP addresses LAN Setting static IP IP Address 192 168 126 254 Netmask 255 255 255 0 gt If the Ethernet port is unable to get an IP address from the DHCP server then the IP address netmask will revert to 192 168 126 254 255 255 255 0 WLAN Setting static IP IP Address 192 168 127 254 Netmask 255 255 255 0 gt If the WLAN port is unable to get an IP address from the DHCP server then the IP address netmask will revert to 192 168 127 254 255 255 255 0 NOTE If you forget the IP address you can use the NPort Search utility from your PC to locate the NPort W2004 unit over the network You will be able to view the IP address on the screen NOTE Only one Network Interface can be used at the same time If the Ethernet Link is active then the WLAN will be disabled If the WLAN is active then the Ethernet Link will be disabled NOTE The default login parameters are username admin and password admin NPort W2004 User s Manual Initial IP Configuration Telnet Console 1 From the Windows desktop click on Start and then select Run 2 Type telnet 192 168 126 254 default IP address in the Open text input box and then click on OK When the Telnet window opens input the password and then press Enter Host Name NPW2004 20 Model Name NPort W004 US LAN MAC Address 00 90 e8 93 04 36 WLAN MAC Address N A Serial No 2 20 Firmware Version 0 0 1 1 beta6
29. 4 4003 pang LISTEN TCP 0 0 192 168 126 254 4004 Std LISTEN TCP 0 0 192 168 126 254 966 wor LISTEN TCP 0 0 192 168 126 254 967 mer LISTEN TCP 0 0 192 168 126 254 968 Dd LISTEN TCP 0 0 192 168 126 254 969 Dad LISTEN TCP 0 0 110 acl td LISTEN TCP 0 0 22 att LISTEN TCP 0 0 80 Sal LISTEN TCP 0 0 22 k LISTEN TCP 0 0 23 al LISTEN TCP 0 0 25 Tor LISTEN TCP 0 0 443 LISTEN TCP 0 0 192 168 126 254 80 192 168 126 100 3103 TIME_WAIT TCP 0 653 192 168 126 254 80 192 168 126 100 3106 ESTABLISHED UDP 0 0 1032 wer UDP 0 0 127 0 0 1 1033 Dad UDP 0 0 127 0 0 1 1034 ad UDP 0 0 127 0 0 1 1035 E UDP 0 0 127 0 0 1 1036 nad UDP 0 0 127 0 0 1 1037 mem UDP 0 0 127 0 0 1 1038 System Log This window displays the System Log Use the Select all button to select the entire log you can then copy and paste the contents into a text file The Clear log and Refresh buttons are used to clear the log and refresh the log contents respectively 5 30 NPort W2004 User s Manual Web Console Configuration 3 Main Menu Overview A wizard Time Settings Network Settings 1 Serial Port Settings System Log System Log J System Management Misc Network Settings H Auto Warning Settings EA System Status WLAN Status Serial to Network Connex Serial Port Status 9 Serial Port Settings 2 Serial Data Log Network Connections a Maintenance Logout Select all Clear log Refresh
30. 4 User s Manual Web Console Configuration E mail Alert E Main Menu A Overview wizard E Time Settings EQ Network Settings 13 Serial Port Settings System Management _ amp Misc Network Settings EMG Auto Warning Settings 1 Event Settings a SNMP Trap EQ System Status E Maintenance Logout Mail Server Settings E mail Alert Mail Server Settings Mail server SMTP My server requires authentication User name Password levees From E mail address Alert Mailing List E mail address 2 E mail address 1 E mail address 3 E mail address 4 Submit Cancel Mail server SMTP Setting Factory Default Necessity IP Address or Domain Name None Optional User name Setting Factory Default Necessity 1 to 15 characters None Optional Password Setting Factory Default Necessity 1 to 15 characters None Optional From E mail address Setting Factory Default Necessity 1 to 63 characters None Optional Alert Mailing List E mail address 1 2 3 4 Setting Factory Default Necessity 1 to 63 characters None Optional 5 27 NPort W2004 User s Manual Web Console Configuration ATTENTION Consult your Network Administrator or ISP for the proper mail server settings The Auto warning function may not work
31. Call Sunrpc 119 Network news Tcanster Protocol NNTP 123 Network Time protocol nnp 161 SNMP Simple Network Mail Protocol 162 SNMP Traps 213 IPX Used for IP Tunneling C Service Information This appendix shows you how to contact Moxa for information about this and other products and how to report problems In this appendix we cover the following topics Q MOXA Internet Services LJ Problem Report Form Q Product Return Procedure NPort W2004 User s Manual Service Information MOXA Internet Services Customer satisfaction is our number one concern and to ensure that customers receive the full benefit of our products Moxa Internet Services has been set up to provide technical support driver updates product information and user s manual updates The following services are provided E mail for technical SUPPOlTt ooooonccincnincnnninnocos support moxa com tw Moxa Group website for product information driver downloads documentation and more Rinnai http www moxa com C 2 NPort W2004 User s Manual Service Information Problem Report Form MOXA NPort W2004 Customer name 1 Moxa Product O NPort W2004 2 Serial Number Problem Description Please describe the symptoms of the problem as clearly as possible including any error messages you see A clearly written description of the problem will allow us to reproduce the symptoms and expedite the repair of your produc
32. Ethernet Flow meters Wireless Access Point RS 232 Flow meters Drives 5 8 NPort W2004 User s Manual Web Console Configuration SSID Enter the name of the wireless network SSID that the W2004 is connected to Channel Select a radio channel for the wireless network from the pull down menu In infrastructure mode the AP will specify the channel automatically In Ad hoc mode the user must use the pull down menu to specify the channel A ATTENTION Click on the Wizard to configure the WLAN IP address quickly Security 3 NPort Web Console Microsoft Internet Explorer BRO RED RADO RREA IAM HAU On O NAOn Jm 2 2 2 43 AED E http 1192 168 126 254 index asp Total Solution fq A Wizard 2 Time Settings Security Configuration Network Settings 1 General Settings po Ethernet Configuration Authentication Open WLAN Configuration WEP Mode Disable aw WEP KEY Index m s ity WEP Key 1 23 Serial Port Settings WEP Key 2 dota WEP Key 3 HE Port 2 HE Port 3 WEP Key 4 3 Port 4 23 System Management The wireless network interface supports data encryption WEP 64 or 128 bits and authentication Open or Shared authentication Authentication Select an authentication scheme of Open or Shared from the pull down menu WEP Mode By default
33. FIFO is Disabled NPort W2004 will transmit one byte each time the Tx FIFO becomes empty and an Rx interrupt will be generated for each incoming byte This will result in a faster response and lower throughput If you want to use XON XOFF flow control we recommend setting the FIFO to Disable Fast Flush only flushes the local buffer a We have added one optional Fast Flush function to Moxa s new NPort Real COM driver b For some applications the user s program will use the Win32 PurgeComm function before it reads or writes data With our design after the program uses this Purge Comm function the NPort driver will keep querying NPort s firmware several times to make sure no data is queued in the NPort firmware buffer rather than just flushing the local buffer This kind of design is used to satisfy some special considerations However it might take more time about several hundred milliseconds than a native COM1 because it needs to work via Ethernet That s why the native COM ports on the motherboard can work fast with this function call but NPort requires much more time In order to accommodate other applications that require a faster response time the new NPort driver implements a new Fast Flush option Note that by default this function is disabled c To begin with make sure there are some PurgeComm functions being used in your application program In this kind of situation you might find that your
34. Moxa s NPort W2004 wireless device server is the ideal choice for connecting your RS 232 422 485 serial devices such as PLCs meters and sensors to a Wired Ethernet LAN and Wireless LAN Your communications software will be able to access the serial devices from anywhere over a local LAN WLAN or the Internet Moreover the WLAN environment offers an excellent solution for applications in which the serial devices are moved frequently from place to place NPort W2004 wireless serial device servers support automatic IP configuration protocols DHCP and manual configuration via a handy web browser console Both IP configuration methods ensure quick and effective installation and the NPort Windows Driver Manager Utility makes Port Mapping very convenient to configure An external antenna increases the range of the wireless connection Users can position the adjustable antenna for maximum signal strength or even replace the antenna with their own for additional flexibility and scalability This feature is particularly useful when a serial device is connected in a high interference area As an added feature a signal strength indicator is located on the front panel to make it easier to troubleshoot connection problems NPort W2004 wireless serial device servers ensure the compatibility of network software that uses a standard network API by providing TCP Server Mode TCP Client Mode and UDP Mode The Real COM TTY drivers allow software that works w
35. NPort W2004 Series User s Manual First Edition November 2004 www moxa com product Moxa Technologies Co Ltd Tel 886 2 8919 1230 Fax 886 2 8919 1231 Web www moxa com MOXA Technical Support Worldwide support moxa com tw The Americas support moxa com NPort W2004 Series User s Manual The software described in this manual is furnished under a license agreement and may be used only in accordance with the terms of that agreement Copyright Notice Copyright O 2004 Moxa Technologies Co Ltd All rights reserved Reproduction without permission is prohibited Trademarks MOXA is a registered trademark of The Moxa Group All other trademarks or registered marks in this manual belong to their respective manufacturers Disclaimer Information in this document is subject to change without notice and does not represent a commitment on the part of Moxa Moxa provides this document as is without warranty of any kind either expressed or implied including but not limited to its particular purpose Moxa reserves the right to make improvements and or changes to this manual or to the products and or the programs described in this manual at any time Information provided in this manual is intended to be accurate and reliable However Moxa Technologies assumes no responsibility for its use or for any infringements on the rights of third parties that may result from its use This product might include unintentional t
36. P Secure data access via standard WEP e Enhanced remote configuration via HTTPS and SSH Product Specifications WLAN Standard Compliance Radio Frequency Type Tx Power 11b Tx Power 11g Rx Sensitivity Transmission Rate Transmission distance Security Antenna Connector Network Mode LAN Ethernet Protection Serial No of ports Interface Port Type RS 485 Data direction 802 11g b DSSS OFDM Maximum 20 dBm Maximum 18 dBm 70 dBm 54 Mbps 85 dBm 11 Mbps 54 Mbps max with auto fallback 54 48 36 24 18 12 11 9 6 5 5 2 1 Mbps Up to 300 meters 12 Mbps in open areas WEP 64 bit 128 bit data encryption Reverse SMA Infrastructure mode Ad Hoc mode 10 100 Mbps RJ45 Built in 1 5 KV magnetic isolation 4 RS 232 422 485 with 15 KV ESD for all signals 8 pin RJ45 ADDC patented Automatic Data Direction Control Serial Communication Parameters Parity Data Bits Stop Bits Flow Control Transmission Speed Console Ports Ethernet console x 1 RS 232 console x 1 None Even Odd Space Mark 5 6 7 8 1 1 5 2 RTS CTS XON XOFF 50 bps to 460 8 Kbps 10 100M LAN 8 pin RJ45 8 pin RJ45 NPort W2004 User s Manual Introduction Software Features Protocols ICMP IP TCP UDP DHCP Telnet DNS SNMP HTTP SMTP SNTP SSH HTTPS Utilities Windows utility for Windows 98 ME 2000 XP 2003 Configuration Web browser Serial console Telnet console Power Requirements
37. P address from the Domain Name System DNS server and then the computer uses the response to connect to the website DNS represents the method used to translate Internet domain names into IP addresses A domain name is an alphanumeric name such as moxa com that it is easier to remember A DNS server is a host that translates this kind of text based domain name into the numeric IP address used to establish a TCP IP connection 5 5 NPort W2004 User s Manual Web Console Configuration In order to use NPort W2004 s DNS feature you need to configure the DNS server Doing so allows NPort W2004 to use a host s domain name to access the host NPort W2004 provides DNS server and DNS server 2 configuration items to configure the IP address of the DNS server DNS Server 2 is included for use when DNS sever is unavailable Ethernet Configuration Main Menu i Ethernet Configuration Overview i Wizard Ethernet Time Settings f z a 3 IP configuration Static y 23 Network Settings i General Settings align 2 A Ethernet Configuration Netmask 255 255 248 0 H WLAN Configuration Gateway 1 Serial Port Settings E System Management n Submit Cancel Logout You must assign a valid IP address to NPort W2004 before it will work in your network environment Your network system administrator should provide you with an IP address and related settings for your network The IP address
38. TCP Server Modei riein En ee Re 4 2 TCP Clot R 4 3 UDP Mode iii A id E ate is 4 3 Real COM Modernitas 4 4 Web Console Configuration ccccccccceeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeseeeeeeeeeeeeees 5 1 OVA as 5 2 Configuring Your BOW id 5 2 Accessing NPort W2004 s Homepage cecccesccssecesecssecseeeeeeereeecnseceseeaecaeeeeeaeeenes 5 3 Time SUM OS a si 5 4 NetWork Settings aoe ee sccescesscauk lia 5 5 Generali Settin G9 italia aes 5 5 Ethernet Configura lados 5 6 WLAN Configuration dea dol eats 5 7 RP dee tenestexistusevecnves edussuboes teen caseupiutevastacs ue aea dees aad 5 10 Operation Modest 5 10 Communication Parameters cccsccssccessesseeeseeeeceeeceseceseceaeeaecaeecaeeeaeeeaeeeeeeeeeeereeaeens 5 20 Syse Mah AA OS 5 21 Misc Network Settings cccccscecsseessessceeseeesceeeesecnsecaeceaeceaecaeecaeeeaeseneeneesereserenerens 5 21 Auto Warning Settings oooonnoonnoninonoonnnoncnoncnnoco nono nocnn cono nonn ron ron n rra rr nr rn nn rn nr narran rra nro 5 25 SYVSLEMUS TALUS an E TEA 5 28 Maintenance e tags tool acces 2 seh da 5 31 Installing and Configuring the Software cccccccccccccccccononcncnnononnnnnos 6 1 OVA baii 6 2 Installing NP ort COM Driver iia and e ada ia aaa 6 2 Installing NPort Search Util Vii iaa 6 6 Appendix A Appendix B Appendix C Appendix D Configuring NPort COM DIV ar 6 9 Configuring NPort Search Util is 6 17 Linux Real TTY and UNIX Fixed TTY Installa
39. The DSR Data Set Ready signal has changed also indicating that the data communication equipment s power is off For example a DSR change to high also means that the DCE is powered ON If the DSR signal changes to low it also means that the DCE is powered off When the DSR changes NPort W2004 will immediately send an e mail or send an SNMP trap Checkbox Items Local Log Setting Factory Default Necessity Enable Disable Disable Optional This feature helps the administrator manage how the NPort W2004 logs system events when enabled events such as Cold start Warm start Authentication failure etc occur To configure this feature click on the Event Type Local Log checkbox Mail Setting Factory Default Necessity Enable Disable Disable Optional This feature helps the administrator manage how the NPort W2004 sends e mail to pre defined e mail boxes when the enabled events such as Cold start Warm start Authentication failure etc occur To configure this feature click on the Event Type Mail checkbox Trap Setting Factory Default Necessity Enable Disable Disable Optional This feature helps the administrator manage how the NPort W2004 sends SNMP Trap to a pre defined SNMP Trap server when the enabled events such as Cold start Warm start Authentication failure etc occur To configure this feature click on the Event Type Trap checkbox 5 26 NPort W200
40. all other applications before continuing Click Next to continue or Cancel to exit Setup Cancel Click on Next to install program files in the default directory or use the folder menu to select an alternative location A Setup NPort Windows Driver Manager Select Destination Directory Where should NPort Windows Driver Manager be installed Select the folder where you would like NPort Windows Driver Manager to be installed then click Next C Program FilesiNPortDrvManager a Program Files Accessories Adobe Analog Devices ArcSoft Borland y a c The program requires at least 1 2 MB of disk space lt Back Cancel NPort W2004 User s Manual Installing and Configuring the Software 5 Click on Next to install the program s shortcuts in the NPort Windows Driver Manager Start Menu folder Select Start Menu Folder gt Where should Setup place the program s shortcuts 7 1 Ready to Install Setup is now ready to begin installing NPort Windows Driver Manager on your computer 7 The Installing window will report the progress of the installation 8 Click on Finish to complete the installation of the NPort W2004 COM Mapping Utility NPort W2004 User s Manual Installing and Configuring the Software a Setup NPort Windows Driver Manager Completing the NPort Windows Driver Manager Setup Wizard Setup has finished installing NPort Windows Driver Manager on
41. alling and Configuring the Software 5 6 Click on Yes to activate the COM ports at this time or click on No to activate the COM ports later Activating the COM ports saves the information in the host system registry The host computer will not have the ability to use the COM port until you click on the Apply icon NPort Windows Driver Manager Ex File COM Mapping View Help E B BRs Exit Add Remove Apply Undo Setting 1 COm2 192 168 126 254 950 966 2 COM3 192 168 126 254 951 967 3 COM5 192 168 126 254 952 968 4 COMB 192 168 126 254 953 969 5 COM Es COMS Information 967 7 COM9 968 8 COM10 969 Total COM Port 0 A The display text corresponding to NPorts whose ports are activated will change from blue to black lt NPort Windows Driver Manager File COM Mapping View Help k A amp e Exit Add Remove Apply Undo Setting Command Port 1 COM2 192 168 126 254 950 966 2 COM3 192 168 126 254 951 967 3 COM 192 168 126 254 950 966 4 Come 192 168 126 254 951 967 5 COM9 192 168 126 254 952 968 6 COM10 192 168 126 254 953 969 NPort W2004 User s Manual Installing and Configuring the Software Te To re configure the settings for a particular NPort click on the row corresponding to that NPort to highlight it and then click on the Setting icon 4 NPort Windows Driver Manager Fie COM Mapping View Help 5 dd RR 8 E Y
42. ctions from the host to the NPort W2004 and from the NPort W2004 to the host 4 2 NPort W2004 User s Manual Choosing the Proper Operation Mode TCP Client Mode In TCP Client mode NPort W2004 can actively establish a TCP connection to a TCP Client Mode pre defined host computer when serial data arrives After the data has been transferred NPort W2004 can disconnect automatically from the host computer by using the TCP alive check time or Request a Inactivity time settings Refer to connection Chapter 5 for more details Proceed with As illustrated in the figure data data transmission transmission proceeds as follows 1 The NPort W2004 requests a connection to the host Serial Device 2 Once the connection is established data can be transmitted in both directions from the host to the NPort W2004 and from the NPort W2004 to the host UDP Mode Compared to TCP communication UDP is faster and more efficient In UDP mode UDP Mode you can unicast or multicast data from the i serial device to one or more host _ computers The serial device can also receive data from multiple host computers making this mode ideal for message display applications Proceed directly with data transmission connection request not required Serial Device 4 3 NPort W2004 User s Manual Choosing the Proper Operation Mode Real COM Mode NPort W2004 comes equipped with COM drivers t
43. data tunneling without control ability Application software that is based on the COM driver will receive a driver response of success when the software uses any of the Win32 API functions The firmware will only send the data back to the driver on the host Data will be sent first in first out when data comes into the NPort W2004 from the Ethernet interface A ATTENTION When Max connection is set to 2 3 or 4 NPort W2004 will use a multi connection application i e 2 3 or 4 hosts are allowed access to the port at the same time When using a multi connection application NPort W2004 will use the serial communication parameters set in the console All of the hosts connected to that port must use the same serial settings If one of the hosts opens the COM port with parameters that are different from NPort W2004 s console setting data communication may not work properly Data Packing Delimiter 1 2 Setting Factory Default Necessity 00 to FF hex None Optional Once the NPort W2004 receives both delimiters through its serial port it immediately packs all data currently in its buffer and sends it to the NPort W2004 s Ethernet port 5 13 NPort W2004 User s Manual Web Console Configuration A ATTENTION Delimiter 2 is optional If left blank then Delimiter 1 alone trips clearing of the buffer If the size of the serial data received is greater than 1 KB the NPort W2004 will automatically
44. e street address where the NPort W2004 is physically located 5 24 NPort W2004 User s Manual Web Console Configuration Auto Warning Settings Event Settings Total Solution for Industrial D J Main Menu Event Settings Overview 9 vaa System Event Time Settings 5 Cold start L_ Local Lo Mail Ti 13 Network Settings is g Omai Trap x w tart il 1 Serial Port Settings ii O Local Log C mail Trap System Management Authentication failure Local Log C mail C Trap _ B Misc Network Settings IP address changed C Local Log C mail Password changed Local Log C Mail Serial Port Event DCD changed E mail Alert SNMP Trap Port 1 Local Log C mail Orrap HQ System Status Port 2 Local Log C mail CTrap 9 Maintenance Port 3 Local Log C mail Orrap E Logout Port 4 C Local Log C mail OTrap Serial Port Event DSR changed Port 1 Local Log O mail Trap Port 2 O Local Log CO mail Trap Port 3 C Local Log C mail Drrap Port 4 Local Log C mail OTrap Submit Cancel System Event Cold start This refers to starting the system from power off contrast this with warm start When performing a cold start NPort W2004 will automatically issue an Auto warning message by e mail or send an SNMP trap after booting up Warm start This refers to restarting the computer without turning the power off When performing a warm start NPort W2004
45. e is set to admin and the default password is also set to admin You may NOT change the username but you can change the password at any time Note that the login function cannot be disabled 3 The NPort W2004 homepage will open OXA Main Menu al wizard Wireless Serial Device Server Welcome to NPort W2000 Series E Time Settings 3 Network Settings Model Name NPort W2004 US 3 Serial No 20 General Settings Firmware Version 0 0 1 1_beta6 Ethernet Configuration Ethernet IP Address 192 168 126 254 13 WLAN Configuration Ethernet MAC Address 00 90 E8 93 04 36 HE Serial Port Settings WLAN IP Address 192 168 127 254 ii WLAN MAC Address N A H System Management Em debate Logout WLAN Mode Infrastructure WEP Mode Disable Serial Port 1 TCP Server Mode 115200 None 8 1 None Serial Port 2 TCP Server Mode 115200 None 8 1 None Serial Port 3 TCP Server Mode 115200 None 8 1 None Serial Port 4 TCP Server Mode 115200 None 8 1 None Active Network Port Ethernet ATTENTION If you can t remember the password the ONLY way to start configuring NPort W2004 is to load factory defaults by using the Reset button which is located near the NPort W2004 s power jack A ATTENTION If you use a web browser other than Internet Explorer remember to Enable the functions to allow cookies that are stored on your computer or allow per session cookies NPort W2004 us
46. echnical or typographical errors Changes are periodically made to the information herein to correct such errors and these changes are incorporated into new editions of the publication Chapter 1 Chapter 2 Chapter 3 Chapter 4 Chapter 5 Chapter 6 Table of Contents INTO CLIO ninia aan e i ea ean irin 1 1 OVSTVI WA A A aid he e 1 2 Package Checklist dite E ta tees eed Ai 1 2 Product Features a ii 1 3 Product Decidido 1 3 Serial Port Pin Assignments seese fone ta did 1 4 Getting Stated e aa aaar a Ee A ences TAE eee cee 2 1 Panel Layout o da 2 2 Connecting the Hard Wi e ad 2 2 Waring Requirements cian ace 2 3 Connecting the PO Wer n 2 3 Connecting to the Network cccccccccseesseeseeesceeseeeeceseceseceecsaecaeeeseeeneeeeeeeeeeseeeeeeeaees 2 3 Connecting to a Serial Device ecceecceescesseeseeeecesecssecseecaeeeseeeeeeeeceseeeeeseeeeseneeneenaees 2 4 LED Ea KST KO t NE E ANENE ANA E NEES 2 4 Initial IP Address Configuration oooommnnncccccnnnononnnanannnononononannnnannnnnnnnnnnnnnnas 3 1 Installation Procedure for First time Users cccccescesseesseesseeseeesecseeeseeeseeeeeeeeeneenseenseeneeaees 3 2 Factory Default IP Address oooooocociocinonioononcnoonononcnncconoco nooo e a ron nn rra rr nn a nro 3 2 Telnet Consoli e a o e o 3 3 Serial Console 19200 O BN e 3 4 Choosing the Proper Operation Mode sseeeeeeeeeeeeeeeeeeeeeeees 4 1 OVELVIC WA A A acevo sca a cat 4 2
47. equest is received Although Inactivity time is disabled the NPort W2004 will check the connection status between the NPort W2004 and remote host by sending keep alive packets periodically If the remote host does not respond to the packet NPort W2004 assumes that the connection was closed down unintentionally NPort W2004 will then force the existing TCP connection to close 5 12 NPort W2004 User s Manual Web Console Configuration A ATTENTION The Inactivity time should be set at least larger than that of Force transmit timeout To prevent the unintended loss of data due to the session being disconnected it is highly recommended that this value is set large enough so that the intended data transfer can be completed Max connection Setting Factory Default Necessity 1 2 3 4 1 Required Max connection is usually used when the user needs to receive data from different hosts simultaneously The factory default is 1 In this case only one specific host can access this port of the NPort W2004 and the Real COM driver on that host will have full control over the port Max connection 1 Allows only 1 host s Real COM driver to open the specific NPort W2004 serial port Max connection 2 to 4 Allows 2 to 4 host s Real COM drivers to open the specific NPort W2004 serial port at the same time When multiple hosts Real COM drivers open the serial port at the same time the COM driver only provides a pure
48. es cookies only for password transmission 5 3 NPort W2004 User s Manual Web Console Configuration Time Settings Main Menu d Time Settings Overview 4 W teard Date and Time Settings 3 Time zone GMT Greenwich Mean Time Dublin Edinburgh Lisbon London 113 Network Settings a E A EAn e eoar don Y Liga Sena port Settinne Local time yy mm dd 2004 11 11 18 56 26 HC System Management Time server 18 145 0 30 2 Logout Submit Cancel NPort W2004 has a built in Real Time Clock that allows you to add real time information to functions such as Auto warning Email or SNMP Trap A ATTENTION First time users should select the time zone first The Console will display the real time according to the time zone compared to GMT If you would like to modify the real time clock select Local time NPort W2004 s firmware will modify the GMT time according to the Time Zone Time zone Setting Factory Default Necessity User selectable time zone GMT Greenwich Mean Time Optional Local tim yy mm dd e Setting Factory Default Necessity User adjustable time GMT Greenwich Mean Time Optional 2000 1 1 2037 12 31 Click on the Modify button to open the Modify time settings window to input the correct local time Z http 11192 168 126 254 Time Settings Microsoft I E B X Modify Time Setting
49. established directly between the NPort W2004 and the host If the host is not on the same subnet the packet is sent to the Gateway address Gateway Setting Factory Default Necessity E g 192 168 1 1 None Optional A gateway is a network gateway that acts as an entrance to another network Usually the computers that control traffic within the network or at the local Internet service provider are gateway nodes NPort W2004 needs to know the IP address of your network s default gateway computer in order to communicate with the hosts outside the local network environment For correct gateway IP address information consult your network administrator A ATTENTION In Dynamic IP environments the firmware will make 3 requests to the DHCP server every 2 4 6 30 seconds until network settings are assigned by the DHCP server The Timeout for each try increases from 1 second to 3 seconds to 5 seconds Ifthe DHCP Server is unavailable the firmware will use the default IP address 192 168 126 254 Netmask and Gateway for IP settings WLAN Configuration Total So A Wizard A Time Settings WLAN Configuration 3 Network Settings Sere n General Settings Network Configuration z Ethernet Configuration IP configuration Static Y _ EX WLAN Configuration IP address 192 168 127 254 a WAR Netmask 255 255 255 0 Security Gateway ha
50. f the serial devices that are connected to NPort W2004 s serial port None Optional Serial Parameters A ATTENTION Check the serial communication parameters in your Serial Device s user s manual You should set up NPort W2004 s serial parameters with the same communication parameters used by your serial devices Baud Rate Setting Factory Default Necessity 50 bps to 460 8 Kbps 115 2 Kbps Required 5 20 NPort W2004 User s Manual Web Console Configuration Data Bits Setting Factory Default Necessity 5 6 7 8 8 Required When the user sets Data bits to 5 bits the Stop bits setting will automatically change to 1 5 bits Stop Bits Setting Factory Default Necessity 1 1 5 2 1 Required Stop bits will be set to 1 5 when Data bits is set to 5 bits Parity Setting Factory Default Necessity None Odd Even Space Mark None Required Flow Control Setting Factory Default Necessity None RTS CTS XON XOFF RTS CTS Required FIFO Setting Factory Default Necessity Enable Disable Enable Required NPort 2004 s serial ports provide a 16 byte FIFO both in the Tx and Rx directions To prevent data loss during communication disable the FIFO setting when your serial device does not have a FIFO Interface Model Ports Settings Factory Default Necessity NPort W2004 4 RS 232 422 485 RS 232 Required
51. hat work with Windows 95 98 ME NT 2000 XP systems The driver establishes a transparent connection between host and serial device by mapping the IP Port of the NPort W2004 s serial port to a local COM port on the host computer One of the main conveniences of using Real COM Mode is that Real COM dd with data Mode allows users to continue using een OE request not required RS 232 422 485 serial communications software that was written for pure serial communications applications The driver intercepts data sent to the host s COM port packs it into a TCP IP packet and then redirects it through the host s Ethernet card At the other end of the connection the NPort W2004 accepts the Ethernet frame unpacks the TCP IP packet and then transparently sends it to the appropriate serial device attached to one of the NPort W2004 s serial ports A ATTENTION Real COM Mode allows several hosts to have access control of the same NPort W2004 The driver that comes with your NPort W2004 controls host access to attached serial devices by checking the host s IP address Refer to Accessible IP Settings in Chapter 5 for more details 4 4 9 Web Console Configuration The Web Console is the most user friendly method available to configure NPort W2004 Series This chapter introduces the Web Console function groups and function definitions The following topics are covered in this chapter a Overview gt Configuring Your
52. ings Serial Port Settings ae Systern Management CE Misc Network Settings Auto Warning Settings 4 System Status EY Maintenance Firmware Upgrade Total Solution for Industrial Device Networking Firmware Upgrade System is upgrading firmware Please DO NOT redirect this page when upgrading is in progress Uploaded File Filename NPW2004_1 0 rom size 11228332 bytes Upgrading please wait 100 done Restarting System SSE _ _ _ i 6 23 A SNMP Agents with MIB Il NPort has built in SNMP Simple Network Management Protocol agent software that supports SNMP Trap and RFC 1213 MIB II The following table lists the standard MIB II groups as well as the variable implementation for NPort RFC1213 MIB II supported SNMP variables System MIB Interfaces MIB IP MIB ICMP MIB SysDescr itNumber ipForwarding IcmpInMsgs SysObjectID ifIndex ipDefaultTTL IcmpInErrors SysUpTime ifDescr ipInreceives IcmpInDestUnreachs SysContact ifType ipInHdrErrors IcmpInTimeExcds SysName ifMtu ipInAddrErrors IcmpInParmProbs SysLocation ifSpeed ipForwDatagrams IcmpInSrcQuenchs SysServices ifPhysAddress ipInUnknownProtos IcmpInRedirects ifAdminStatus ipInDiscards IcmpInEchos ifOperStatus ipInDelivers IcmpInEchoReps ifLastChange ipOutRequests IcmpInTimestamps ifInOctets ipOutDiscards IcmpTimestampReps 1fInUcastPkts ipOutNoRoutes IcmpInAdd
53. intenance gt Firmware Upgrade in the left pane and then use the Browse button to locate the firmware file Click on Submit to start upgrading 101 x Ele Edt view Favorites Tools Help ay Qe x E TN JO Search S o Favorites A media O B Address la http 192 168 126 254findex asp y Go Links Total Solution for Industrial Device Networking SJ Main Menu A overview Q Wizard 2 Time Settings HE Network Settings Select Firmware File JFANPW2004_1 0 rom Browse serial Port Settings By System Management Cancel EQ Misc Network Settings _ S Auto Warning Settings O system Status Firmware Upgrade Firmware Upgrade LM Firmware Upgrade ru a port Click on OK 6 22 NPort W2004 User s Manual Installing and Configuring the Software Microsoft Internet Explorer xj 2 Warning The firmware upgrade process may take 5 to 10 minutes to complete Please DO NOT redirect to other pages while Firmware upgrade is in progress Are you sure that you want to proceed 4 After the firmware has been upgraded the NPort W2004 will reboot automatically Z NPort Web Console icrosoft Internet Explorer File Edit View Favorites Tools Help 21D x a Our BD ae Tero me OO LB Address la http 192 168 126 254findex asp y Go Links E Main Menu E Overview A Wizard Time Settings Network Sett
54. internal buffer size The serial communication buffer size for NPort W2004 is 1 KB per port UDP Mode Destination IP address 1 Setting Factory Default Necessity IP address range Begin Empty E g Begin 192 168 1 1 End Empty Required End 192 168 1 10 Port 4001 Destination IP address 2 3 4 Setting Factory Default Necessity IP address range E g Begin 192 168 1 11 Begin Empty Optional End 192 168 1 20 Allows NPort W2004 to connect actively to the remote host whose IP address is set by this parameter 5 19 NPort W2004 User s Manual Web Console Configuration Communication Parameters E NPort Web Console Microsoft Internet Explorer BRO REO RO EREA IAD SAO Q ix 0 14ad Ox ka O 2 3 2 JA 3 FED El htp 192 168 126 254 index asp eae Menu Communication Parameters Overview A wizard Port Settings Time Settings ae z Network Settings Port alias Serial Port Settings Parameters Baud rate 115200 i Parity None Data bits 8 Y Stop bits 1 amp Flow control None Y E System Management FIFO O Enable O Disable Logout Interface RS 232 v C Apply the above settings to all serial ports Submit _ _ Cancel Port 1 2 3 4 Port alias Setting Factory Default Necessity 1 to 39 characters e g PLC No 1 Port alias is included to allow easy identification o
55. ith COM TTY ports to be set up to work over a TCP IP network in no time This excellent feature preserves your software investment and lets you enjoy the benefits of networking your serial devices instantly To make your management task easier the NPort W2004 Series provides additional features such as password authentication IP filter WEP support for 64 bit and 128 bit encryption and SNMP support Package Checklist NPort W2004 is shipped with the following items Standard Accessories e NPort W2004 x 1 Documentation amp Software CD RJ45 to RJ45 Ethernet cross over cable RJ45 to male DB9 cable CBL RJ45M9 150 RJ45 to female DB9 cable CBL RJ45F9 150 Power adaptor Warranty Booklet e Quick Installation Guide Optional Accessories e DK 35A DIN Rail Mounting Kit 35 mm e CBL RJ45M9 150 8 pin RJ45 to male DB9 cable 150 cm e CBL RJ45F9 150 8 pin RJ45 to female DB9 cable 150 cm e CBL RJ45M25 150 8 pin RJ45 to male DB25 cable 150 cm e CBL RJ45F25 150 8 pin RJ45 to male DB25 cable 150 cm NOTE Notify your sales representative if any of the above items is missing or damaged 1 2 NPort W2004 User s Manual Introduction Product Features Connect any serial device to WiFi 802 11g b network 4 RS 232 422 485 ports at up to 460 8 Kbps Web based configuration via built in Ethernet or WLAN Supports Windows Unix and Linux Real COM drivers Versatile socket operation modes including TCP Client Server and UD
56. l port to the hosts tty port Refer to Mapping TTY Ports below for details Hardware Installation Before proceeding with the software installation make sure you have completed the hardware installation The default IP address for NPort Server is 192 168 127 254 NOTE After installing the hardware you MUST configure the NPort operating mode to Real COM Mode NPort W2004 User s Manual Installing and Configuring the Software Installing the Driver Files Get the driver file from the product CD ROM or Moxa website Log in to the console as a super user root Execute cd to go to the root directory Copy the driver file npreal2xx tgz to the directory Execute tar xvfz npreal2xx tgz to copy all files into the system meaoges Execute tmp moxa mxinst NOTE For RedHat AS ES WS and Fedora Corel extra argument is needed tmp moxa mxinst SP1 g The shell script will install the driver files automatically After installing the driver you will be able to see several files in the usr lib npreal2 driver folder including gt mxaddsvr Add Server mapping tty port gt mxdelsvr Delete Server un mapping tty port gt mxloadsvr Reload Server gt mxmknod Create device node tty port gt mxrmnod Remove device node tty port gt mxuninst Remove tty port and driver files At this point you will be ready to map the NPort serial port to the system tty port See Mapping TTY Ports below fo
57. must be unique within the network otherwise NPort W2004 will not have a valid connection to the network First time users should refer to Chapter 3 Initial IP Address Configuration for more information Choose from two possible IP configuration modes Static and DHCP located under the web console screen s IP configuration drop down box IP configuration Method Function Definition Static User defined IP address Netmask Gateway DHCP DHCP Server assigned IP address Netmask Gateway DNS and Time Server IP address Setting Factory Default Necessity E g 192 168 1 1 192 168 126 254 Required IP addresses of the form x x x 0 and x x x 255 are invalid An IP address is a number assigned to a network device such as a computer as a permanent address on the network Computers use the IP address to identify and talk to each other over the network Choose a proper IP address that is unique and valid in your network environment Netmask Setting Factory Default Necessity E g 255 255 255 0 255 255 255 0 Required 5 6 NPort W2004 User s Manual Web Console Configuration A netmask is used to group network hosts into subnets When a packet is sent out over the network the NPort W2004 will use the netmask to check whether the desired TCP IP host specified in the packet is on the same subnet as the NPort If the address is on the same subnet a connection is
58. n such as serial printer driver In general case you can ignore these settings Baud Rate a0 y Parity None y Data Bits Stop Bits hy Flow Control None y M Apply Al Selected Port X Cancel 10 To save the configuration to a text file select Export COM Mapping You will then be able to import this configuration file to another host and use the same COM Mapping settings in the other host NPort Windows Driver Manager Eile COM Mapping View Help Fgh Add Ctrl N Ex q Remove Cti D a al Apply Undo Setting Ctrit C 192 168 126 254 951 192 168 126 254 950 192 168 126 254 951 192 168 126 254 962 192 168 126 254 953 192 168 126 254 967 966 967 968 969 NPort W2004 User s Manual Installing and Configuring the Software Configuring NPort Search Utility The Broadcast Search function is used to locate all NPort W2004s that are connected to the same LAN as your computer After locating an NPort W2004 you will be able to change the IP address Since the Broadcast Search function searches by MAC address and not IP address all NPort W2004s connected to the LAN will be located regardless of whether or not they are part of the same subnet as the host 1 Open the NPort Search Utility and then click on the Search icon PS NPort Search Utility File Function Help 2 2 a x af Exit Search Search IP Locate Console No Model
59. ng a multi connection application NPort W2004 will use the serial communication parameters set in the console All of the hosts connected to that port must use the same serial settings If one of the hosts opens the COM port with parameters that are different from NPort W2004 s console setting data communication may not work properly Data Packing Delimiter 1 2 Setting Factory Default Necessity 00 to FF hex None Optional Once the NPort W2004 receives both delimiters through its serial port it immediately packs all data currently in its buffer and sends it to the NPort W2004 s Ethernet port A ATTENTION Delimiter 2 is optional If left blank then Delimiter 1 alone trips clearing of the buffer If the size of the serial data received is greater than 1 KB the NPort W2004 will automatically pack the data and send it to the Ethernet However to use the delimiter function you must at least enable Delimiter 1 If Delimiter 1 is left blank and Delimiter 2 is enabled the delimiter function will not work properly Force transmit Setting Factory Default Necessity 0 to 65535 ms 0 Optional 0 Disable force transmit timeout 1 to 65535 Forces the NPort W2004 s TCP IP protocol software to try to pack serial data received during the specified time into the same data frame This parameter defines the time interval during which NPort W2004 fetches the serial data from its internal buffer
60. ng to Load Factory Default Restart Ports Select the ports you would like to restart and then click on the Submit button to restart the ports Total Solution fo I Main Menu i E Restart Ports E Overview a Wizard Restart the selected serial ports E Time Settings 4 Network Settings Select Ports EU Serial Port Settings ae System Management E Misc Network Settings Auto Warning Settings 4 System Status EX Maintenance i A Firmware Upgrade 3 Configuration Import E Configuration Export Load Factory Default Change Password mi M2 Bis Pla Restart System 3 Logout 5 34 NPort W2004 User s Manual Web Console Configuration Restart System Click on Submit to reboot the NPort W2004 E Main Menu 4 Restart System 1 Overview E Wizard The configuration has been changed Please click Submit button to reboot with new conf E Time Settings HC Network Settings 11 Warning 1 Serial Port Settings 33 System Management Misc Network Settings 2 Auto Warning Settings system Status EY Maintenance Firmware Upgrade Reboot will disconnect both serial and Ethernet connections and data Configuration Import A Configuration Export Load Factory Default 3 Change Password E Restart Ports Logout 5 35 6 Installing and Configuring the Software This following topics are covered in this chapter
61. nication Param aC Port 2 EQ Port 3 aE Port 4 43 System Management HC Misc Network Settings H Auto Warning Settings System Status E Maintenance Firmware Upgrade Configuration Import 2 Configuration Export Load Factory Default Port 1 2 3 4 Inactivity time Operation Modes Port Settings Port Operation mode Inactivity time Max connection Data Packing Delimiter 1 Delimiter 2 Force transmit TCP Server Mode Local TCP port Command port 2 TCP Server Mode 0 0 65535 ms 1 1 4 00 Hex C Enable o 4001 966 0 65535 ms D Apply the above settings to all serial ports Submit Cancel Setting Factory Default Necessity 0 to 65535 ms 0 ms Optional 0 ms TCP connection is not closed due to an idle serial line 0 65535 ms NPort W2004 automatically closes the TCP connection if there is no serial data activity for the given time After the connection is closed NPort W2004 starts listening for another host s TCP connection This parameter defines the maintenance status as Closed or Listen for the TCP connection The connection is closed if there is no incoming or outgoing data through the serial port during the specific Inactivity time If the Inactivity time is set to 0 the current TCP connection is kept active until a connection close r
62. ode i 1 WLAN Status IP Configuration Serial to Network Conner TP Address A Netmask Serial Port Status Serial Port Settings Serial Data Log 5 28 NPort W2004 User s Manual Web Console Configuration Serial to Network Connections The Serial to Network Connections page lists the operation modes and IP addresses associated with each of the wireless device server s serial ports E Main Menu 3 f i j Serial to Network Connections 1 Overview C Wizard Port OP Mode 1 Time Settings 1 TCP Server Mode 4 Network Settings 2 TCP Server Mode 1 Serial Port Settings 3 TCP Server Mode 4 TCP Server Mode 3 System Management E Misc Network Settings 13 Auto Warning Settings EX System Status EJ WLAN Status ea 1 Serial Port Status Serial Port Settings 1 Serial Data Log i Network Connections E System Log 7 Maintenance Serial Port Status Connections The Serial Port Status page lists serial transmission stats for each of the wireless device server s serial ports Serial Port Status Port TxCnt RxCnt TxTotalCnt RxTotalCnt 1 0 0 0 0 2 0 0 0 0 3 0 0 0 0 4 0 0 0 0 DSR off off off off off off off off DCD off off off off Serial Port Settings The Serial Port Settings page lists the serial transmission settings for each of the four ports Serial Port Settings Port Baud Rate Bits Stop Parit
63. om the host computer i 5 Time Settings given time He Network Settings EU Serial Port Settings Bey System Management EXE Misc Network Settings E Accessible IP List i E 2 Serial Data Logging 2 SNMP Agent 2 Auto Warning Settings Settings Alive Check Time 7 0 99 min TCP alive check time Setting Factory Default Necessity 0 to 99 min 7 min Optional 0 min TCP connection is not closed due to an idle TCP connection 1 to 99 min NPort W2004 automatically closes the TCP connection if there is no TCP activity for the given time After the connection is closed NPort W2004 starts listening for another host s TCP connection Serial Data Logging Total Solution for Indus Main Menu y Serial Data Logging I Overview i 4 wizard The data to and from the serial ports can be recorded and stored in the system RAM for troublest ac Time Settings 4 Network Settings Serial Data Logging ae Serial Port Settings Service O Enable Disable Sa System Management Ey Misc Network Settings ges A Accessible IP List TCP Alive Check Time E SNMP Agent Auto Warning Settings NPort provides the capability to store data logs for all serial ports The logs will be stored in the system RAM The data will be deleted when NPort is powered off Due to the system s SDRAM limitation the memory size of local buffers is fixed Each serial port i
64. on parameter definitions This chapter covers the following topics Overview TCP Server Mode TCP Client Mode UDP Mode Real COM Mode Ooooo NPort W2004 User s Manual Choosing the Proper Operation Mode Overview NPort W2004 wireless Serial Device Servers are used to network enable traditional RS 232 422 485 devices A Serial Device Server is a tiny computer equipped with a CPU real time OS and TCP IP protocols that can bi directionally translate data between the serial and Ethernet formats The Serial Device Server lets you use a computer to access manage and configure remote facilities and equipment over the Internet from anywhere in the world Traditional SCADA and data collection systems rely on serial ports RS 232 422 485 to collect data from different types of instruments Since NPort W2004 wireless Serial Device Servers network enable instruments equipped with an RS 232 422 485 communication port your SCADA and data collection system will be able to access all instruments connected to a standard TCP IP network regardless of whether the devices are used locally or at a remote site NPort W2004 is an external IP based network device that allows you to expand the number of serial ports for a host computer on demand As long as your host computer supports the TCP IP protocol you won t be limited by the host computer s limited number of conventional busses such as ISA or PCI or lack of drivers for various operating s
65. pack the data and send it to the Ethernet However to use the delimiter function you must at least enable Delimiter 1 If Delimiter 1 is left blank and Delimiter 2 is enabled the delimiter function will not work properly Force transmit Setting Factory Default Necessity 0 to 65535 ms 0 Optional 0 Disable force transmit timeout 1 to 65535 Forces the NPort W2004 s TCP IP protocol software to try to pack serial data received during the specified time into the same data frame This parameter defines the time interval during which NPort W2004 fetches the serial data from its internal buffer If data is incoming through the serial port NPort W2004 stores the data in the internal buffer NPort W2004 transmits data stored in the buffer via TCP IP but only if the internal buffer is full or if the Force transmit time interval reaches the time specified under Force transmit timeout The optimal Force transmit timeout depends on your application but it must be at least larger than one character interval within the specified baud rate For example assume that the serial port is set to 1200 bps 8 data bits 1 stop bit and no parity In this case the total number of bits needed to send a character is 10 bits and the time required to transfer one character is 10 bits 1200 bits s 1000 ms s 8 3 ms Therefore you should set Force transmit to be larger than 8 3 ms so in this case it must be greater than o
66. r detailed instructions Mapping TTY Ports Before mapping tty ports you must set the operation mode of your NPort to Real Com Mode We provide two ways to map tty ports Mapping tty ports automatically After logging in as a super user enter the directory usr lib npreal2 driver and then execute mxaddsvr to map the target NPort serial port to the host tty ports The syntax of mxaddsvr is mxaddsvr NPort IP Address Total Ports Data port Cmd port Example 1 cd usr lib npreal2 driver mxaddsvr 192 168 3 4 16 Example2 cd usr lib npreal2 driver mxaddsvr 192 168 3 4 16 4001 966 In Example 1 16 tty ports will be added all with IP 192 168 3 4 but with data ports equal to 950 951 965 and command ports equal to 966 967 968 981 In example2 16 tty ports will be added all with IP 192 168 3 4 but with data ports equal to 4001 4002 4016 and command ports equal to 966 967 968 981 The following actions will be performed gt Modify the npreal2d cf gt Create tty ports in directory dev with major amp minor number configured in 6 19 NPort W2004 User s Manual Installing and Configuring the Software npreal2d cf gt Stop and then restart the driver Removing Mapped TTY ports As with the Mapping TTY Ports task we provide two ways to remove mapped tty ports Remove the mapped tty ports automatically After logging in as root enter the direc
67. r equal to 10 ms If you want to send a series of characters in the same packet the serial device attached to NPort W2004 should send that series of characters during a time interval less than the Force transmit timeout and the total length of data must be less than or equal to NPort W2004 s internal buffer size The serial communication buffer size for NPort W2004 is 1 KB per port TCP Server Mode Local TCP Port Setting Factory Default Necessity 1 to 65535 4001 Required The Local TCP port is the TCP port that NPort W2004 uses to listen to connections and that other devices must use to contact NPort W2004 To avoid conflicts with well known TCP ports the default is set to 4001 Command port Setting Factory Default Necessity 1 to 65535 966 Optional The Command port is a listen TCP port for IP Serial Lib commands from the host In order to prevent a TCP port conflict with other applications the user can set the Command port to another port if needed IP Serial Lib will automatically check the Command Port on NPort W2004 so that the user does not need to configure the program 5 14 NPort W2004 User s Manual Web Console Configuration TCP Client Mode J Main Menu Port Settings Overview Port IO 3 Wizard Operation mode TCP Client Mode Time Settings Inactivity time o _ 0 65535 ms HC Network Settings E Serial Port Settings Data Packing PO Po
68. rMasks ifInNUcastPkts ipReasmTimeout IcmpOutMsgs 1fInDiscards ipReasmReqds IcmpOutErrors 1fInErrors ipReasmOKs IcmpOutDestUnreachs NPort W2004 User s Manual SNMP Agents with MIB II System MIB Interfaces MIB IP MIB ICMP MIB SysServices iffmUnknownProtos ipReasmFails IcmpOutTimeExcds ifOutOctets ipFragOKs IcmpOutParmProbs ifOutUcastPkts ipFragFails IcmpOutSrcQuenchs ifOutNUcastPkts ipFragCreates IcmpOutRedirects ifOutDiscards ipAdEntAddr IcmpOutEchos ifOutErrors ipAdEntIfIndex IcmpOutEchoReps ifOutQLen ipAdEntNetMask IcmpOutTimestamps ifSpecific IpAdEntBcastAddr IcmpOutTimestampReps ipAdEntReasmMaxSize IempOutAddrMasks IpNetToMedialfIndex IcmpOutAddrMaskReps IpNetToMediaPhysAddress IpNetToMediaNetAddress IpNetToMediaType IpRoutingDiscards UDP MIB TCP MIB SNMP MIB UdpInDatagrams tcpRtoAlgorithm snmpInPkts UdpNoPorts tepRtoMin snmpOutPkts UdpInErrors tepRtoMax snmpInBad Versions UdpOutDatagrams tepMaxConn snmpInBadCommunityNames UdpLocalAddress tcpActiveOpens snmpInASNParseErrs UdpLocalPort tcpPassiveOpens snmpInTooBigs tcpAttempFails snmpInNoSuchNames Address Translation MIB tcpEstabResets snmpInBad Values Atl fIndex tcpCurrEstab snmpInReadOnlys AtPhysAddress tcpInSegs snmpInGenErrs AtNetAddress tcpOutSegs snmpInTotalReq Vars A 2 NPort W2004 User s Manual SNMP Agents with MIB II
69. rch Program Files Accessories Adobe Analog Devices ArcSoft Borland 7 gt EE The program requires at least 0 5 MB of disk space lt Back Cancel NPort W2004 User s Manual Installing and Configuring the Software 5 Click on Next to install the program s shortcuts in the NPort Search Utility Start Menu folder Select Start Menu Folder Where should Setup place the program s shortcuts 7 A s e Start Menu folder in which you would like Setup to create the program s slick Next 6 Click on Install to proceed with the installation a Setup NPort Search Utility Ready to Install Setup is now ready to begin installing NPort Search Utility on your computer 7 The Installing window will report the progress of the installation 8 Click on Finish to complete the installation of the NPort W2004 Search Utility NPort W2004 User s Manual Installing and Configuring the Software Completing the NPort Search Utility Setup Wizard Setup has finished installing NPort Search Utility on your computer The application may be launched by selecting the installed icons Click Finish to exit Setup pecenccecencsnseesvosseccsrsencescssssacsnssnscessossnccssssnseney AAA Configuring NPort COM Driver The NPort COM Driver utility installs Real COM drivers that work under Windows 98 ME 2000 XP 2003 After you install NPort COM Driver you can set up the NPort W2004 s serial ports
70. rti Delimiter 1 00 Hex C Enable Operation Modes EL Delimiter 2 00 3 Communication Paramete 00 ne Enable HE Port 2 Force transmit 0 0 65535 ms HA Port 3 TCP Client Mode HE Port 4 Destination IP Address AC System Management Destination IP address 1 4001 Logout Destination IP address 2 4001 Destination IP address 3 4001 Destination IP address 4 4001 Designated Local Port Designated Local Port 1 C Enable Port 5011 Designated Local Port 2 C Enable Port 5012 Designated Local Port 3 C Enable Port 5013 Designated Local Port 4 C Enable Port 5014 TCP connect on Startup O Any Character i gt 2 FAbolv the above settinas to all serial ports Port 1 2 3 4 TCP alive check time Setting Factory Default Necessity 0 to 99 min 7 min Optional 0 min TCP connection is not closed due to an idle TCP connection 1 to 99 min NPort W2004 automatically closes the TCP connection if there is no TCP activity for the given time After the connection is closed NPort W2004 starts listening for another host s TCP connection Inactivity time Setting Factory Default Necessity 0 to 65535 ms 0 ms Optional 0 ms TCP connection is not closed due to an idle serial line 0 65535 ms NPort W2004 automatically closes the TCP connection if there is no serial data activity for the given time After the connection is closed NPort W2004
71. s Date yy mm dd Time hh mm ss 2004 11 y 11 18 58 e 5 4 NPort W2004 User s Manual Web Console Configuration Time server Setting Factory Default Necessity IP Address or Domain Name None Optional E g 192 168 1 1 time stdtime gov tw or time nist gov NPort W2004 uses SNTP RFC 1769 for auto time calibration Input the correct Time server IP address or domain name Once NPort W2004 is configured with the correct Time server address NPort W2004 will request time information from the Time server every hour Network Settings General Settings J Main Menu 5 General Settings A Overview Wizard Time Settings Device Server Settings 33 Network Settings Server name NPW2004_20 ag as am DNS server 1 Ethernet Configuration DNS server 2 El WLAN Configuration Serial Port Settings Y System Management A Logout Click on the General Settings option to modify the Server name and DNS server IP addresses or domain names Server name Setting Factory Default Necessity Alphanumeric NPW2004 lt Serial No gt Optional DNS server 1 DNS server 2 Setting Factory Default Necessity E g 192 168 1 1 None Optional IP addresses of the form x x x 0 and x x x 255 are invalid When a user wishes to visit a particular website the computer first requests the website s correct I
72. s allotted 64 KB to store the port s log file 5 23 NPort W2004 User s Manual Web Console Configuration SNMP Agent Main Menu SNMP Agent en E Overview j wizard Configuration Time Settings SNMP Network Settings 1 Serial Port Settings 43 System Management EQ Misc Network Settings i a Accessible IP List Contact name Location Read community string System description OEnable O Disable public Device Server TCP Alive Check Time Y Serial Data Logging RA Mta Warnina Gattinac To enable the SNMP Agent function select the enable option and enter a Community Name e g public Community name Setting Factory Default Necessity 1 to 39 characters e g Support 886 89191230 public Optional 300 A community name is a plain text password mechanism that is used to authenticate weakly queries to agents of managed network devices Contact Setting Factory Default Necessity 1 to 39 characters e g Support 886 89191230 None Optional 300 The SNMP contact information usually includes an emergency contact name and telephone or pager number Location Seine Factory Default Necessity 1 to 39 characters e g Floor 1 Office No 2 None Optional Specify the location string for SNMP agents such as NPort W2004 This string is usually set to th
73. stop bit and no parity In this case the total number of bits needed to send a character is 10 bits and the time required to transfer one character is 10 bits 1200 bits s 1000 ms s 8 3 ms Therefore you should set Force transmit to be larger than 8 3 ms so in this case it must be greater than or equal to 10 ms If you want to send a series of characters in the same packet the serial device attached to NPort W2004 should send that series of characters during a time interval less than the Force transmit timeout and the total length of data must be less than or equal to NPort W2004 s internal buffer size The serial communication buffer size for NPort W2004 is 1 KB per port TCP Client Mode Destination IP address 1 2 3 4 Setting Factory Default Necessity IP address or Domain Name None Required Designated Local Port 1 2 3 4 Setting Factory Default Necessity Port No if Enabled Disabled Optional If disabled the local TCP port will be chosen automatically by the NPort whenever a connection is established If enabled the designated local port will be used as the local TCP port A ATTENTION Inactivity time is ONLY active when TCP connect on is set to Any character 5 17 NPort W2004 User s Manual Web Console Configuration UDP Mode J Main Menu 1 Overview A Wizard 2 Time Settings Network Settings 53 Serial Port Settings 23 Port
74. t NPort W2004 User s Manual Service Information Product Return Procedure For product repair exchange or refund the customer must 4 4 4 Provide evidence of original purchase Obtain a Product Return Agreement PRA from the sales representative or dealer Fill out the Problem Report Form PRF Include as much detail as possible for a shorter product repair time Carefully pack the product in an anti static package and send it pre paid to the dealer The PRA should be visible on the outside of the package and include a description of the problem along with the return address and telephone number of a technical contact Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one of the follo
75. te e Where necessary it is advisable to label the wiring to all devices in the system Connecting the Power Connect the 12 48 VDC power line with NPort W2004 s power jack When the power is supplied properly the Ready LED will show a solid red color until the system is ready at which time the Ready LED will change to a green color Connecting to the Network Connect one end of the Ethernet cable to NPort W2004 s 10 100M Ethernet port and the other end of the cable to the Ethernet network If the cable is properly connected NPort W2004 will indicate a valid connection to the Ethernet in the following ways e The Ethernet LED maintains a solid green color when connected to a 100 Mbps Ethernet network e The Ethernet LED maintains a solid orange color when connected to a 10 Mbps Ethernet network e The Ethernet LED will flash when Ethernet packets are being transmitted or received 2 3 NPort W2004 User s Manual Getting Started Connecting to a Serial Device Connect the serial data cable between NPort W2004 and the serial device Serial data cables are optional accessories for NPort W2004 Refer to Chapter 1 under Optional Accessories in the Ordering Information section for information about the RJ45 to DB25 and RJ45 to DB9 cables LED Indicators NOTE LED Indicators The front panel of NPort W2004 has eleven LED indicators as described in the following table LED Name LED Color LED Function Stead
76. tion ooooonnnncccnoncccnonancconnnancnnnnnanonnnnnnnonnnnnos 6 18 Installing the Linux Real TTY driver ooooconncnnncinocnonnnoncnonconononoconncnn nono nonnrnnnrnnrannnnnnnos 6 18 Installing the UNIX Fixed TTY Driver cooooocniccnonnconnconconnconoconooncconcnon nono nonnrrnnrnnnonnnnnos 6 20 Upgrading the FirMWare oooooooconononononononnnonnnonoconoco nono nconncon nono nono nr dobavo ainis sbaen sirais ssia 6 22 SNMP Agents with MIB ll ooo cccccccoonnnncnnnccononcconancnnnnncnoncnnnonnnannnennnnnonas A 1 Well Known Port NUMbeXFS occccccocaconaconaconaconanonaronaronaronaronaronaronaronaronananas B 1 Service Information icici ccc cieis ccc eceicede Sevececnccbasvdodevetaceccuadsccdededcusiseataccdsdiacde C 1 MOXA Internet Services o da oles Bees C 2 Problem Report Porm ii ais C 3 Product Return Proce duit ena ese e E ees seh hci aah Fee C 4 Federal Communication Commission Interference Statement D 1 1 Introduction Moxa s NPort W2004 Series of wireless serial device servers provide users with an easy means of comnecting RS 232 422 485 serial devices to a WLAN The 4 port NPort W2004 is ideal for environments where a LAN is not available or where serial devices are moved frequently The following topics are covered in this chapter Overview Package Checklist Product Features Product Specifications Ooooo Serial Port Pin Assignments NPort W2004 User s Manual Introduction Overview
77. tory usr lib npreal2 driver and then execute mxdelsvr to delete a server The syntax of mxdelsvr is mxdelsvr IP Example cd usr lib npreal2 driver mxdelsvr 192 168 3 4 If you don t provide the IP address in the command line the program will list the installed servers and total ports on the screen so that you can only choose the index of the installed server list to delete The following actions will be performed gt Modify the npreal2d cf gt Remove the relevant tty ports in directory dev gt Stop and then restart the driver Removing the Driver Files Driver Removal will remove all driver files mapped tty ports and unload the driver To do this you only need to enter the directory usr lib npreal2 driver and then execute mxuninst to uninstall the driver This program will perform the following actions gt Unload the driver gt Delete all files and directories in usr lib npreal2 gt Delete directory usr lib npreal2 gt Modify the system initializing script file Installing the UNIX Fixed TTY Driver Installation and Configuration Step 1 Log in to UNIX and create a directory for the MOXA TTY E g to create a directory named usr etc execute the command mkdir usr etc Step 2 Copy moxattyd tar tothe usr etc directory by executing the commands cp moxattyd tar usr etc cd usr etc Step 3 Extract the source code from the tar file by executing the command tar xvf moxattyd tar
78. uld void the user s authority to operate the equipment
79. w i 1 Wizard This function will reset all settings to the factory default values All the previous settings w E Time Settings 61 Network Settings Options ae Serial Port Settings Ey System Management Reset to factory default excluding IP configuration 5 Misc Network Settings O Reset to factory default 2 Auto Warning Settings Laman EXA Maintenance f Firmware Upgrade 2 Configuration Import Configuration Export a 2 Change Password Restart Ports i L E Restart System Logout Change Password To change the password for the NPort W2004 input the Old password New password and then retype the new password in the Retype password input box To erase the password simply leave all three text input boxes blank and then click on Submit 5 33 NPort W2004 User s Manual Web Console Configuration Main Menu R Change Password Overview wizard Time Settings Network Settings Serial Port Settings New Password System Management Confirm New Password 1 Misc Network Settings 2 Auto Warning Settings 4 System Status Password Current Password Cancel EN Maintenance Firmware Upgrade Configuration Import Configuration Export Load Factory Default Restart Ports i Restart System Logout PLOPLED ATTENTION If you forget the password the ONLY way to configure NPort W2004 is by using the Reset button on NPort W2004 s casi
80. will automatically send an e mail or send an SNMP trap after rebooting Authentication Failure The user inputs a wrong password from the Console or Administrator When authentication failure occurs NPort W2004 will immediately send an e mail or send an SNMP trap IP address changed The user has changed NPort W2004 s IP address When the IP address changes NPort W2004 will send an e mail with the new IP address before NPort W2004 reboots If the NPort W2004 is unable to send an e mail message to the mail server within 15 seconds NPort W2004 will reboot anyway and abort the e mail auto warning Password changed The user has changed NPort W2004 s password When the password changes NPort W2004 will 5 25 NPort W2004 User s Manual Web Console Configuration send an e mail with the password changed notice before NPort W2004 reboots If the NPort W2004 is unable to send an e mail message to the mail server within 15 seconds NPort W2004 will reboot anyway and abort the e mail auto warning Serial Port Event DCD Changed The DCD Data Carrier Detect signal has changed also indicating that the modem connection status has changed For example a DCD change to high also means Connected between local modem and remote modem If the DCD signal changes to low it also means that the connection line is down When the DCD changes NPort W2004 will immediately send an e mail or send an SNMP trap Serial Port Event DSR Changed
81. wing measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation FCC Caution Any changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate this equipment Moxa declares that NPort W2004 is limited to CH1 CH11 by specified firmware when controlled in the USA IMPORTANT NOTE FCC Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and your body This transmitter must not be co located or operating in conjunction with any other antenna or transmitter INFORMATION TO USER The user s manual or instruction manual for an intentional or unintentional radiator shall caution the user that changes or modifications not expressly approved by the party responsible for compliance co
82. y Flow Control 1 115200 8 1 None XON XOFF 2 115200 8 1 None XON XOFF 3 115200 8 1 None XON XOFF 4 115200 8 1 None XON XOFF FIFO Enable Enable Enable Enable Interface RS 232 RS 232 RS 232 RS 232 Serial Data Log This Text box is enabled only when Data logging is enabled The data log contents are displayed in ASCII mode or HEX mode Use the Select all button to select the entire log you can then copy and paste the contents into a text file The Clear log and Refresh buttons are used to clear the log and refresh the log contents respectively 5 29 NPort W2004 User s Manual Web Console Configuration Main Menu E overview wizard E Time Settings HC Network Settings Select Port Serial Port Settings ae System Management EQ Misc Network Settings 4 Auto Warning Settings _ Gy System Status E WLAN Status i Serial to Network Connec Serial Port Status Serial Port Settings Serial Data Log Network Connections System Log Maintenance Serial Data Log Data Log ASCII ASCIM HEX Select all Clear log Refresh Network Connections The Network Connections page displays the current status of the network connection Network Connections Protocol Recv Q Send Q Local Address Foreign Address State TCP 0 0 1024 nan LISTEN TCP 0 0 20000 AS LISTEN TCP 0 0 192 168 126 254 4001 Er LISTEN TCP 0 0 192 168 126 254 4002 oat LISTEN TCP 0 0 192 168 126 25
83. y on Power is on and NPort is booting up Blinking fast once every 0 5 sec Indicates a LAN IP red conflict Blinking slowly once every sec Looking for an IP when no DHCP server is available Ready Steady on Power is on and NPort is functioning normally Blinking fast once every 0 5 sec Loading factory default green configuration after holding in the reset button for 5 seconds Blinking slowly once every sec The device server has been located by NPort Search utility off Power is off or power error condition exists On Wireless enabled Blinking fast once every 0 5 sec Indicates a WLAN IP WLAN green conflict Blinking slowly once every sec Looking for an IP when no DHCP server is available orange Serial port is receiving data P1 P2 P3 P4 green Serial port is transmitting data No data is being transmitted or received through the serial off port Signal The number of lit LEDS indicates the WLAN signal strength een th En When 0 1 2 3 4 5 LEDs are lit the corresponding 5 LEDs 8 WLAN status is Connection Fail Bad Fair Good Very Good Excellent orange 10 Mbps Ethernet connection 10 100 M 3 Ethernet green 100 Mbps Ethernet connection off Ethernet cable is disconnected or has a short If the signal strength is such that 2 or fewer signal strength LEDs are lit communication with NPort W2004 could become unstable or even fail
84. y privileged users The following table shows famous port numbers among the well known port numbers For more details please visit the IANA website at http www iana org assignments port numbers TCP Socket Application Service 0 reserved 1 TCP Port Service Multiplexor 2 Management Utility 7 Echo 9 Discard 11 Active Users systat 13 Daytime 15 Netstat 20 FTP data port 21 FTP CONTROL port 23 Telnet 25 SMTP Simple Mail Transfer Protocol 37 Time Time Server 42 Host name server names server NPort W2004 User s Manual Well Known Port Numbers TCP Socket Application Service 43 Whois nickname 49 Login Host Protocol Login 53 Domain Name Server domain 79 Finger protocol Finger 80 World Wibe Web HTTP 119 Netword news Transfer Protocol NNTP 123 Network Time Protocol 213 IPX 160 223 Reserved for future use UDP Socket Application Service 0 reserved 2 Management Utility 7 Echo 9 Discard 11 Active Users systat 13 Daytime 35 Any private printer server 39 Resource Location Protocol 42 Host name server names server 43 Whois nickname 49 Login Host Protocol Login 53 Domain Name Server domain 69 Trivial Transfer Protocol TETP 70 Gopler Protocol 79 Finger Protocol 80 World Wide Web HTTP 107 Remote Telnet Service 111 Sun Remote Procedure
85. your computer The application may be launched by selecting the installed icons Click Finish to exit Setup 6 5 NPort W2004 User s Manual Installing and Configuring the Software Installing NPort Search Utility 1 Click on the INSTALL UTILITY button in the NPort Installation CD auto run window to install the NPort Search Utility gt NPort Installation CD Wireless Serial Device Servers Software CD Ver1 1 Po Press the INSTALL UTILITY button to install NPort W2000 utility NPort W2000 utility can be installed under Windows9x ME NT 2000 XP 2003 systems _ A i 2 Once the program starts running click on Yes to proceed 3 Click on Next when the Welcome window opens to proceed with the installation 6 6 NPort W2004 User s Manual Installing and Configuring the Software 4 Welcome to the NPort Search Utility Setup Wizard This will install NPort Search Utility Yer0 1 1 on your computer It is recommended that you close all other applications before continuing Click Next to continue or Cancel to exit Setup Click on Next to install program files in the default directory or use the folder menu to select an alternative location 9 Setup NPort Search Utility Select Destination Directory Where should NPort Search Utility be installed Select the folder where you would like NPort Search Utility to be installed then click Next C Program Files NPortS ea
86. ystems In addition to providing socket access NPort W2004 also comes with a Real COM TTY driver that transmits all serial signals intact This means that you can continue using existing COM TTY based software eliminating the need to invest in additional costly software Three different Socket Modes are available TCP Server TCP Client and UDP Server Client The main difference between the TCP and UDP protocols is that TCP guarantees delivery of data by requiring the recipient to send an acknowledgement to the sender UDP does not require this type of verification making it possible to offer speedier delivery UDP lets you unicast to one IP address or multicast to groups of IP addresses TCP Server Mode In TCP Server mode NPort W2004 is configured with a unique IP Port address TCP Server Mode on a TCP IP network NPort W2004 waits passively to be contacted by the host computer allowing the host computer to establish a connection with and get data from the serial device This operation mode also supports up to 4 O Request a simultaneous connections so that multiple connection hosts can collect data from the same serial 2 Proceed with device at the same time data transmission Serial Device As illustrated in the figure data transmission proceeds as follows 1 The host requests a connection from the NPort W2004 configured for TCP Server Mode 2 Once the connection is established data can be transmitted in both dire

Download Pdf Manuals

Related Search

Related Contents

A web-HUMAN Renal Physiology Experiment Response to  Manual de puesta en marcha del extractor de humos de soldadura    Getting to Know Your NEVO  Natara DayNotez Desktop User Manual    Tatung TLM TLM-1705 User's Manual  取扱ー組立説明書には、商品を正確に組立て、末永く    Guide d`achat NSU Ro 80 - Ro 80 Club International  

Copyright © All rights reserved. Failed to retrieve file