Home

User Manual PCM-2000 Series

1. User Manual PCM 2000 Series A modular mini PCle system for selected industry applications AD ANTECH net ig an Intelligent Pla Copyright The documentation and the software included with this product are copyrighted 2014 by Advantech Co Ltd All rights are reserved Advantech Co Ltd reserves the right to make improvements in the products described in this manual at any time without notice No part of this manual may be reproduced copied translated or transmitted in any form or by any means without the prior written permission of Advantech Co Ltd Information provided in this manual is intended to be accurate and reliable How ever Advantech Co Ltd assumes no responsibility for its use nor for any infringe ments of the rights of third parties which may result from its use Acknowledgements Intel and Pentium are trademarks of Intel Corporation Microsoft Windows and MS DOS are registered trademarks of Microsoft Corp All other product names or trademarks are properties of their respective owners Product Warranty 5 years Advantech warrants to you the original purchaser that each of its products will be free from defects in materials and workmanship for two years from the date of pur chase This warranty does not apply to any products which have been repaired or altered by persons other than repair
2. The PCM 24R2PE will need an additional 24VDC from the internal power source refer to the PIN assignment on the power board as shown in the table below The PCM 24R2PE power board supports an external power connector on CN1 as an option Description of PIN Use PIN1 DCIN24V PIN3 GND PIN2 DCIN24V PIN4 GND 6 c5 Iu Wo ba i J PC5 E CN1 le It 1 LE ias 00 ST EZ Ex B TEISEBLHLUE 57 PCM Series User Manual PCM Series User Manual 58 PCM 24U2U3 Sections include E Initial Inspection E Driver and Advantech Device Manager Installation Pin Assignment and Wiring 10 1 Initial Inspection You should find the following items inside the shipped package W PCM 24U2U3 Communication Module PCM 24U2U3 PCI Express Mini Card 2 port USB3 0 I O plate Wired signal Cable Wired power Cable m PCM 2000 DVD ROM including User Manual Industrial Communication Driver Utility and mini PCle communication card The PCM 24U2US was carefully inspected mechanically and electrically before it was shipped It should be free of marks and scratches and in perfect working order when received As you unpack the PCM 24U2U3 check for signs of shipping damage damaged box scratches dents etc If it is dam
3. 61 PCM Series User Manual 3 Select Install to continue the installation Renesas Elegironics USB 30 Host Controller Drivers InstallShield Wizard m c 5 lille lt mme A ER nn nn Ready to Install the Program The wizard is ready to begin installation Click Install to begin the installation If you want to review or change any of your installation settings click Back Click Cancel to exit the wizard i InstallShield 4 After a while the installation will be complete Renesas Electronics USB 3 0 Host Controller Driver InstallShield Wizard Ey gt m se Me u A um es 2 InstallShield Wizard Complete The InstallShield Wizard has successfully installed Renesas Electronics USB 3 0 Host Controller Driver Click Finish to exit the wizard lt Back Cancel 5 After the hardware has been installed the card will be automatically detected Be teme File Action View Help 3 m Hs gt 4 Computer c Disk drives Me Display adapters gt Qj Human Interface Devices I D IDE ATA ATAPI controllers gt Keyboards M Mice and other pointing devices iil Monitors b Network adapters b lf Other devices D EB Portable Devices D TF Ports COM amp LPT gt E Processors b a Sound video and game controllers 4 System devices 4 Universal Serial Bus controllers Generic USB Hub Intel R 8 Series USB Enhanced Host Controller 1
4. PCM Series User Manual 7 3 2 Wiring The PCM 23C 1CF uses a flat cable to connect from the I O plate to the internal SATA HDD connector The PIN assignment is in the below table Description of PIN Use CN1 PINS1 GND PINP5 GND PINS2 SATA TX PINP6 GND PINS3 SATA TX PINP7 5V PINS4 GND PINP8 5V PINS5 SATA RX PINP9 5V PINS6 SATA_RX PINP10 GND PINS7 GND PINP11 NC PINP1 3 3V PINP12 GND PINP2 3 3V PINP13 NC PINP3 3 3V PINP14 NC PINP4 GND PINP15 NC Q Q Seco oc oO oO oO 2000000 The existing SATA cable length may not be enough Advantech can help to custom ize the cable for your system requirements PCM Series User Manual 40 PCM 24R1TP AE 1 port Giga LAN mPCle RJ45 Sections include E Initial Inspection E Driver and Advantech Device Manager Installation B Pin Assignment and Wiring 8 1 Initial Inspection You should find the following items inside the shipped package PCM 2400 Communication Module PCM 2400 mini PCle Card I O plate Flat Cable mW PCM 2000 DVD ROM including ndustrial Communication Driver Utility and mini PCle communication card The PCM 24R1 TP was carefully inspected mechanically and electrically before it was shipped It should be free of marks and scratches and in perfect working order when received As you unpack the PCM 24R1TP check for signs of shipping damage damaged box scratches dents etc If
5. lisplays its nr 69 PCM Series User Manual A 2 Diagnostic LEDs Table A 1 Diagnostic LED Definitions LED Light On Light Off LED 1 Chip Status It s working It s not working LED 2 MRAM Access Status MRAM is being accessed MRAM isn t being accessed PCM Series User Manual 70 71 PCM Series User Manual AD ANTECH Enabling an Intelligent Planet wwWw advantech com Please verify specifications before quoting This guide is intended for reference purposes only All product specifications are subject to change without notice No part of this publication may be reproduced in any form or by any means electronic photocopying recording or otherwise without prior written permis sion of the publisher All brand and product names are trademarks or registered trademarks of their respective companies Advantech Co Ltd 2014
6. 17 18 19 20 21 22 23 Read these safety instructions carefully Keep this User Manual for later reference Disconnect this equipment from any AC outlet before cleaning Use a damp cloth Do not use liquid or spray detergents for cleaning For plug in equipment the power outlet socket must be located near the equip ment and must be easily accessible Keep this equipment away from humidity Put this equipment on a reliable surface during installation Dropping it or letting it fall may cause damage The openings on the enclosure are for air convection Protect the equipment from overheating DO NOT COVER THE OPENINGS Make sure the voltage of the power source is correct before connecting the equipment to the power outlet Position the power cord so that people cannot step on it Do not place anything over the power cord All cautions and warnings on the equipment should be noted If the equipment is not used for a long time disconnect it from the power source to avoid damage by transient overvoltage Never pour any liquid into an opening This may cause fire or electrical shock Never open the equipment For safety reasons the equipment should be opened only by qualified service personnel If one of the following situations arises get the equipment checked by service personnel The power cord or plug is damaged Liquid has penetrated into the equipment The equipment has been exposed to moisture The equipmen
7. 3 4 4 PCM 24D4R4 The following tables and figures show the pin assignments of 1 female DB37 connector one the iDoor bracket to male DB9 for PCM 24D4R4 card in RS 422 and RS 485 modes Table 3 9 PCM 24D4R4 Male DB9 on Cable Pin RS 422 RS 485 1 Tx Data 2 Tx Data 1 2 3 A4 5 00000 5 GND GND s OOOO 7 6 7 8 9 8 9 Table 3 10 PCM 24D4R4 Female DB37 on iDoor bracket Pin RS 422 RS 485 Pin RS 422 RS 485 1 20 2 3 TxD 3 Data 21 3 RxD 3 3 GND 3 GND 22 4 23 5 3 TxD 3 Data 24 3_RxD 6 25 4 TxD 4 Data 7 4 RxD 26 4 GND 4 GND 8 27 9 28 4 TxD 4 Data 10 4 RxD 29 11 2 TxD 2 Deta 30 2 RxD 12 2 GND 2_GND 31 13 l 32 14 2 TxD 2_Data 33 2_RxD 15 J 34 1 TxD 1 Data 16 1_RxD 35 1 GND 1 GND 17 J 36 18 l 37 1_TxD 1_Data 19 1_RxD 19 1 O0o0O00000000000000000 9000000000000 0000 0 37 20 PCM Series User Manual 3 5 Wiring 3 5 1 RS 232 Signal Wiring Since the RS 232 interface is not strictly defined many devices have their own con nection methods which may ignore some signal lines or define reserved lines for other functions It is best to refer to the user s manual for your device for installation instructions You may find the following helpful In general DTE
8. 9C26 Intel R USB 3 0 eXtensible Host Controller Intel R USB 3 0 Root Hub Renesas Electronics USB 3 0 Host Controller Renesas Electronics USB 3 0 Root Hub USB Composite Device USB Mass Storage Device USB Root Hub La PCM Series User Manual 62 10 2 3 Uninstall 1 Inthe Control Panel click Renesas Electronics USB 3 0 Host Controller Driver then uninstall e gt Control Panel Programs Programs and Features Search Programs and Features p Control Panel Home Uninstall or change a program View installed updates To uninstall a program select it from the list and then click Uninstall Change or Repair Turn Windows features on or oH Organize Uninstall Name Publisher Installed On E9 Intel R Network Connections 18 6 110 0 Intel 4 14 2015 Wintel R ThermatAnalysis Tool 5 0 1017 Intel Corporation 5 13 2015 4 Intel Graphics Driver Intel Corporation 4 15 2015 34 Intel Management Engine Components Intel Corporation 4 15 2015 M4 Intel USB 3 0 eXtensible Host Controller Driver Intel Corporation 4 15 2015 E Microsoft Visual C 2010 x64 Redistributable 10 0 Microsoft Corporation 4 14 2015 m Microsoft Visual C 2010 x86 Redistributable 10 0 Microsoft Corporation 4 14 2015 Nd Realtek High Definition Audio Driver Realtek Semiconductor Corp 4 14 2015 iB Renesas Electronics USB 3 0 Host Controller Driver Renesas Electronics Corporation 5 20 2015 B RTS IEEELS88 PTP_x6
9. CAM L s A 3 GND 3 Sc ud ps CAN H 4 9 CAM L 2 6 5 1 Female DBS Connector Male DBS Connector Figure 4 3 PCM 26D2CA DB 9 connector pin assignments CH DEF urn e RED 1000pF DAN NHH WY GND EX Figure 4 4 PCM 26D2CA DB 9 connector schematics The CAN standard supports half duplex communication This means that just two wires are used to transmit and receive data Table 4 2 PCM 26D2CA Pin Description Pin Signal Description 2 CAN_L LOW level CAN voltage input output 3 GND Ground 7 CAN_H HIGH level CAN voltage input output PCM Series User Manual 28 4 5 Wiring CAN bus main board has two FPC connectors for wiring to two CAN bus transceiver boards through FPC cables Please ensure to follow Figure 4 5 and Figure 4 6 for appropriate wiring in between Figure 4 5 FPC cable wiring Figure 4 6 Wiring on module side 29 PCM Series User Manual PCM Series User Manual 30 PCM 23U1DG AE USB Slot w Lock for USB Dongle Sections include E Initial Inspection E Driver Setup and Installation E Pin Assignment E Wiring 5 1 5 2 Initial Inspection You should find the following items inside the shipped package B PCM 2300 Storage Module I O plate Wire cable Wm PCM 2000 DVD ROM including A Industrial Communication Driver Utility and mini PCle communication card The PCM 23U1DG was carefully inspected mechanically and electrically before it was shipp
10. V3 3_LANC LAN LINK1000 V1 9 LANO LAN_ACT LAN_LINK100 LAN_MDIO LAN_MDIO LAN MDI14 LAN MDIT LAN_MDI2 LAN_MDI2 LAN_MDI3 LAN_MDIS SMOFIX i The existing cable length may not enough Advantech can help to customize the cable for system inquires 47 PCM Series User Manual PCM Series User Manual 48 PCM 24R2PE AE 2 Port Giga LAN w PoE mPCle RJ45 PCM 24R2GL AE 2 Port Giga LAN mPCle RJ45 Sections include E Initial Inspection E Driver and Advantech Device Manager Installation B Pin Assignment and Wiring 9 1 Initial Inspection You should find the following items inside the shipped package PCM 2400 Communication Module PCM 2400 mini PCle Card I O plate Power board For PCM 24R2PE AE only Wire Cable m PCM 2000 DVD ROM including User Manual Industrial Communication Driver Utility and mini PCle communication card The PCM 24R2PE was carefully inspected mechanically and electrically before it was shipped It should be free of marks and scratches and in perfect working order when received As you unpack the PCM 24R2PE check for signs of shipping damage damaged box scratches dents etc If it is damaged or it fails to meet specifications notify our service department or your local sales representative immediately Also notify the carrier Retain the shipping carton and packing material for inspection by the carrier
11. 2 2 1 2 3 Chapter 3 3 1 3 2 3 3 3 4 3 5 Chapter 4 4 1 4 2 Introduction 1 Brtreje m 2 PCM Support Summary sise 2 PCM 2300MR AE 9 Initial Inspection iere rre rote ee nenne eR RR SE weceaxenian 4 Driver Setup amp Installation Advantech Device Manager Installation 5 genui E 7 2 39 1 Windows Format tette ente ct ead co hnic ado in 7 2 3 2 Advantech provides MRAM driver format 8 PCM 24DxRx AE 11 Initial Inspectlon nic dtr oett one Pn tete ated ed i eade 12 Jumper and Switch Settings nn 13 3 2 1 PCM 24D2R4 Settings 13 Table 3 1 Master Slave Settings 13 Table 3 2 Terminal Resistor Settings nen 13 3 2 2 PCM 24D4R4 Settings 14 Table 3 3 Master Slave Settings 14 Table 3 4 Terminal Resistor Settings nennen 14 Driver Setup amp Installation 15 3 93 1 Introduction ert teta n RES 15 3 9 2 Driver Setup u a lien ennt edt iege t aene dada 15 3 3 3 Steps for Operating System Driver Setup 15 3 34 Driver Uninstall meisten 16 Pin ASSIgnments 5 eoi ite ro ie o dE OD ea E Pte tie 17 34 1 PCM 24D2R2 ai aka ans 17 Table 3 5 PCM 24D2R2 Male DB9 on iDoor bracket 17 3 4 2 POM 24D2RA iiit e e E SRL lan 17 Table 3 6 PCM 24D2R4 Male DB9
12. 64 PCM 2300MR AE 07 Initial Inspection cct he opi ee e Eee 68 Diagnostic LEDS n us nee anna eio dette in 70 Table A 1 Diagnostic LED Definitions 70 ix PCM Series User Manual PCM Series User Manual Introduction This chapter provides a general description of the PCM modules description and support sum mary Sections include Bi Description PCM Support Summary 1 4 Description Advantech designed iDoor technology by support for the flexible optional connector arrangement for the Advantech embedded Automation computing platform including connector internal cabling and a wide range of I O and communication Modules Supporting Optional WLAN and GPRS modules including Antenna RT Ethernet and serial Fieldbus options B Non volatile Memory options B Optical isolated Serial Ports RS232 422 485 WB LAN ports supporting IEEE 1588 PTP m O extension modules B Wireless IO communication 1 2 PCM Support Summary Model Manual Drivers Datasheet Startup PCM 2300MR AE Chapter 2 Refer to DVD Referto DVD Refer to DVD PCM 24D2R4 AE Chapter 3 Refer to DVD Referto DVD Refer to DVD PCM 24D2R2 AE Chapter 3 Refer to DVD Referto DVD Refer to DVD PCM 24D4R4 AE Chapter 3 Refer to DVD Referto DVD Refer to DVD PCM 24DAR2 AE Chapter 3 Refer to DVD Referto DVD Refer to DVD PCM 26D2CA AE Chapter 4 Refer to DVD Referto DVD Refer to DVD PCM 26D1PB AE Refer to DVD Fro
13. After inspection we will make arrangements to repair or replace the unit When you handle the PCM 24R2PE remove it from its protective packaging by grasping the rear metal panel Keep the anti vibration packing Whenever you remove the card from the PC store it in this package for protection Warning Discharge your body s static electric charge by touching the back of the grounded chassis of the system unit metal before handling the board A You should avoid contact with materials that hold a static charge such as plastic vinyl and Styrofoam Handle the board only by its edges to avoid static damage to its integrated circuits Avoid touching the exposed cir cuit connectors We also recommend that you use a grounded wrist strap and place the card on a static dissipative mat whenever you work With it PCM Series User Manual 50 9 2 Driver Setup amp Installation Advantech Device Manager Installation 9 2 1 Introduction This chapter describes the driver installation configuration and removal procedures for the mentioned Windows operating system We strongly recommend that you install the software driver before you install the hardware into your system 9 2 2 Installation When you follow the startup manual to install the module appropriated Please follow the steps below to install Advantech PCM 24R2PE Driver 1 Goto Device Manager and you will find an error in Other devices File Action View Help 9 t e ig d S 4 ij ad
14. Intel R 1210 Gigabit Network Connection 4 WP Intel R B50 Gigabit Network Connection amp Intel R B50 Gigabit Network Connection 2 Y Ports COM amp LPT Ll Processors 4 Sound video and game controllers 4 4 System devices dE ACPI Fan E ACPI Fixed Feature Button 1 ACPI Power Button 1M ACPI Sleep Button aM ACPI Thermal Zone 1 Goto Control Panel and select Intel Network Connections 19 1 51 0 and click Uninstall El ControlPanel gt All Control Panel item Programs ond Features Control Panel Heme Uninstall or change a program View installed updates To uninstall a program select t from the ist and then click Uninstal Change or Repair 38 Tum Windows features on or om De Name Publisher Installed On Version Passmark Software iaiam2 p Flinte Power Thermal Li Intl Corporation spams 12 38H ote Network Connections 191 518 Inte Lame 21519 Be rel Therma Analysis Tool 4 34 500 Intel Corporaton 3721 2018 MA Intel Graphics Drver Intel Corporation vum 351501073 LA Intel Trusted Execution Engine Inte Cerpration inama 1001050 IA Intel USB 34 eXtensible Host Controller Driver Intl Corporation inama 30023 Intel Product version 191 310 Suppor link http wawdntelcom 2 Ej Control Pond AllContrel Panel Rems Programs and Festures Control Panel Home Uninstall or change a program View installed updates Touninstall program select it from the lit and then click Uninstall Cha
15. PCle communication interface card W Industrial Communication Driver Utility and mini PCle communication card user s manual in PCM 2000 DVD ROM PCM 26D2CA was carefully inspected mechanically and electrically before it was shipped It should be free of marks and scratches and in perfect working order when received As you unpack the PCM Module check for signs of shipping damage damaged box scratches dents etc If itis damaged or it fails to meet specifications notify our ser vice department or your local sales representative immediately Also notify the car rier Retain the shipping carton and packing material for inspection by the carrier After inspection we will make arrangements to repair or replace the unit When you handle the PCM Module remove it from its protective packaging by grasp ing the rear metal panel Keep the anti vibration packing Whenever you remove the card from the PC store it in this package for protection Warning Discharge your body s static electric charge by touching the back of the grounded chassis of the system unit metal before handling the board A You should avoid contact with materials that hold a static charge such as plastic vinyl and Styrofoam Handle the board only by its edges to avoid static damage to its integrated circuits Avoid touching the exposed circuit connectors We also recommend that you use a grounded wrist strap and place the card on a static dissipative mat whenever yo
16. Pin Assignment and Wiring For details about Advantech s PCM 2300TP Pin Assignment and Wiring please refer to the user manual from Advantech PCA TPM 00A1E product information The PIN assignment of the cable may different from the current system pin definition Advantech can help to customize the cable for different pin assignments PCM Series User Manual 36 PCM 23C1CF AE SATAII to CFast Sections include E Initial Inspection E Driver Setup and Installation E Pin Assignment E Wiring 7 1 Initial Inspection You should find the following items inside the shipped package m PCM 2300 Storage Module I O plate PCM 2000 DVD ROM including A Industrial Communication Driver Utility and mini PCle communication card The PCM 23C1CF was carefully inspected mechanically and electrically before it was shipped It should be free of marks and scratches and in perfect working order when received As you unpack the PCM 23C1CF check for signs of shipping damage damaged box scratches dents etc If it is damaged or it fails to meet specifications notify our service department or your local sales representative immediately Also notify the carrier Retain the shipping carton and packing material for inspection by the carrier After inspection we will make arrangements to repair or replace the unit When you handle the PCM 23C1CF remove it from its protective packaging by grasping the rear metal panel Keep the anti vibr
17. This chapter describes the driver installation configuration and removal procedures for the mentioned Windows operating system We strongly recommend that you install the software driver before you install the hardware into your system 10 2 2 Installation When you follow the startup manual to install the module appropriated Please follow the steps below to install Advantech PCM 24U2U3 Driver 1 Select Next to continue the installation Renesas Electronics USB 3 0 Host Controller Driver InstallShield Wizard Welcome to the InstallShield Wizard for Renesas Electronics USB 3 0 Host Controller Driver The InstallShield Wizard will install Renesas Electronics USB 3 0 Host Controller Driver on your computer To continue click Next 2 Select accept the terms of the license agreement and then click Next to continue the installation Renesas Electronics USB 3 0 Host Controller Driver InstallShield Wizard Zum mt mn License Agreement Please read the following license agreement carefully End User License Agreement 3 RENESAS for USB3 0 Software Software YOU AGREE TO BE BOUND BY THE TERMS AND CONDITIONS OF THIS EULA BY INSTALLING COPYING OR OTHERWISE USING SOFTWARE IF YOU DO NOT AGREE THE TERMS AND accept the terms of the license agreement do not accept the terms of the license agreement eld lt Back f Next gt Cancel
18. To access new features open Device Manager and view the properties of the network adapters 8 After the hardware has been installed the card will be automatically detected Open Device Manager to check it File Action View Help eo TIDE mele RS 4 i advantech PC 1 Computer ca Disk drives X Display adapters j Human Interface Devices IDE ATA ATAPI controllers Keyboards A Mice and other pointing devices KK Monitors 4 2 Network adapters AP Intel R 210 Gigabit Network Connection EP Intel R 210 Gigabit Network Connection 2 amp Intel R 210 Gigabit Network Connection 3 Intel R 1210 Gigabit Network Connection 4 X Intel R B50 Gigabit Network Connection a Intel R B50 Gigabit Network Connection 2 Portable Devices f Ports COM amp LPT D Processors 4 Sound video and game controllers 4 4M System devices jM ACPI Fan ME ACPI Fixed Feature Button jM ACPI Power Button aM ACPI Sleeo Button 53 PCM Series User Manual 9 2 3 Uninstall Go to Device Manager to check the device you want to remove File Action View Help mit Hr ml sS 4 4 advantech PC W Computer ca Disk drives V Display adapters Human Interface Devices IDE ATA ATAPI controllers Keyboards F Mice and other pointing devices ME Monitors Network adapters AP Intel R 1210 Gigabit Network Connection KP Intel R 1210 Gigabit Network Connection 2 AP Intel R 1210 Gigabit Network Connection 3 amp
19. devices Dp Monitors SJ Multi port serial adapters E Network adapters M Ports COM amp LPT BR Processors E Ramdisk Sound video and game controllers lt gt Storage volumes M System devices Universal Serial Bus controllers HE 2 3 Format 2 3 1 Windows Format 1 Right click the mouse to select format P My Computer le x File Edit View Favorites Tools Help sack x M d JO Search gt Folders E X i E adess jmwcmue mde Files Stored on This Computer Gi Shared Documents cJ Administrator s Documents Hard Disk Drives Cua UNO 2174A C a AdvNYRAM Z Open Explore Devices with Removable Storage Search Sharing and Security er Removable Disk D Copy Disk 7 PCM Series User Manual 2 Select Start to complete MRAM format Format AdvNVRAM 2 AdvNVRAM Enable Compression Greate an MS DOS startup disk 2 3 2 Advantech provides MRAM driver format 1 Use Device Manager i Device Manager gt m E8 mmm E oEM 03DSAGATZAM H Advantech IAG Onboard Devices E E Advantech NVRAM Disk Devices 8 Advantech NYRAM Disk E Computer we Disk drives mg Display adapters H 88 Human Interface Devices H E IDE ATA ATAPI controllers Bt Keyboards Properties ey Mice and other pointing devices H Monitors AP Multi port serial adapters re Network adapters H Ports COM amp LPT ER Pr
20. install Advantech PCM 24R1TP Driver 1 Select Next to continue the installation al Intel R Network Connections Install Wizard Welcome to the install wizard for Intel R Network Connections intel Installs drivers Intel R Network Connections and Advanced Networking Services WARNING This program is protected by copyright law and international treaties 2 Select I agree to continue the installation J Intel R Network Connections Install Wizard Es License Agreement a intel Please read the following license agreement carefully INTEL SOFTWARE LICENSE AGREEMENT IMPORTANT READ BEFORE COPYING INSTALLING OR USING Do not copy install or use this software and any associated materials collectively the Software provided under this license agreement Agreement until you have carefully read the following terms and conditions By copying installing or otherwise using the Software you agree to be bound by the terms of this Agreement If you do not agree to the terms of this Agreement _ d mnt ann inntall accen tha Cafhemnen I accept the terms in the license agreement Print I do not accept the terms in the license agreement 43 PCM Series User Manual 3 Select Driver for Windows Device Manager Intel PROSet to continue the installation Setup Options Select the program features you want installed Install V Drivers i Intel R PROSet for Windows Device Man
21. it is damaged or it fails to meet specifications notify our service department or your local sales representative immediately Also notify the carrier Retain the shipping carton and packing material for inspection by the carrier After inspection we will make arrangements to repair or replace the unit When you handle the PCM 24R1TP remove it from its protective packaging by grasping the rear metal panel Keep the anti vibration packing Whenever you remove the card from the PC store it in this package for protection Warning Discharge your body s static electric charge by touching the back of the grounded chassis of the system unit metal before handling the board A You should avoid contact with materials that hold a static charge such as plastic vinyl and Styrofoam Handle the board only by its edges to avoid static damage to its integrated circuits Avoid touching the exposed cir cuit connectors We also recommend that you use a grounded wrist strap and place the card on a static dissipative mat whenever you work With it PCM Series User Manual 42 8 2 8 2 1 8 2 2 Driver Setup amp Installation Advantech Device Manager Installation Introduction This chapter describes the driver installation configuration and removal procedures for the mentioned Windows operating system We strongly recommend that you install the software driver before you install the hardware into your system Installation Follow the steps below to
22. need for a driver on the PCM 23U1DG PCM Series User Manual 32 5 3 Pin Assignment and Wiring 5 3 1 Pin Assignment The following table and figure shows the pin assignments of connector on the iDoor I O module for the PCM 23U1DG Cable PIN assignment CN1 USB w locked CN2 Internal cable for USB PIN1 5V PIN1 5V PIN2 D PIN2 D PIN3 D PIN3 D PIN4 GND PIN4 GND PIN5 GND_IO 5 3 2 Wiring PCM 23U1DG is using flat cable to connect from IO plate to internal USB pin header The PIN assignment in the below table Cable PIN assignment CN2 Internal cable for USB Cable head for the system PIN header PIN1 5V PIN2 5V PIN2 D PIN4 D PIN3 D PING D PIN4 GND PIN8 GND The PIN assignment of the cable may different from the current system pin definition Advantech can help to customize the cable for different pin assignments 33 PCM Series User Manual PCM Series User Manual 34 PCM 2300TP AE Sections include E Initial Inspection E Driver Setup and Installation B Pin Assignment E Wiring 6 1 6 2 Initial Inspection You should find the following items inside the shipped package B PCM 2300 Storage Module I O plate Wire cable Wm PCM 2000 DVD ROM including Industrial Communication Driver Utility and mini PCle communication card The PCM 2300TP was carefully inspected mechanically and electrically before it was shipp
23. on iDoor Bracket 17 3 4 3 POM 24DAR2 aie Medal tede asi eaa ua e and 18 Table 3 7 PCM 24D4R2 Male DB9 on Cable 18 Table 3 8 PCM 24D4R2 Female DB37 on iDoor bracket 18 3 4 4 PCM 24D4R4 n es nennen nennen nennen 19 Table 3 9 PCM 24D4R4 Male DB9 on Cable 19 Table 3 10 PCM 24D4R4 Female DB37 on iDoor bracket 19 npo C H E 20 3 5 1 RS 232 Signal Wirlrnig i rre threats 20 Table 3 11 Terminal or PC DTE Connections 20 Table 3 12 Modem Connections 20 Table 3 13 Terminal without Handshake nnen 21 3 5 2 RS 422 Signal Wiring NaN 21 Table 3 14 RS 422 DB9 Pin Assignment ss 21 3 5 8 RS 485 Signal Wiring 22 Figure 3 1 RS 485 Wiring Topology 22 POM 26D2GA notes 29 Initial Inspection iret a bn ntt e pin e te ets 24 Driver and Advantech Device Manager Installation 25 vii PCM Series User Manual 4 3 4 4 4 5 Chapter 5 5 1 5 3 Chapter 6 Chapter 7 7 1 7 2 7 3 Chapter 8 8 1 8 2 8 3 Chapter 9 Chapter 9 9 1 9 2 PCM Series User Manual Jumper and Switch Settings esssssem n 27 Fig
24. pointing devices gt il Monitors 4 Lu Network adapters POR EP Intel R 82574L Gigabit Network Connection E Intel R Ethernet Connection D18 LM i olf Intel R 1210 Gigabit Network Connection gt l Other devices gt Mi Portable Devices D Ports COM amp LPT gt D Processors P Sound video and game controllers p 4 System devices b Universal Serial Bus controllers 45 PCM Series User Manual 8 3 Pin Assignment and Wiring 8 3 1 Pin Assignment The following table and figure shows the pin assignments of the LAN connector on the iDoor I O module for PCM 24R1TP Description of PIN Use CN2 PIN1 TX DO PIN7 BI_D3 PIN2 TX DO PIN8 BI D3 PIN3 RX_D1 PIN9 LAN ACT PIN4 BI_D2 PIN10 V3 3 LAN PIN5 BI D2 PIN11 LAN_LINK1000 PIN6 RX_D1 PIN12 LAN_LINK100 la N 1OP 24T5 Rev Al ci is 19C324T501 01 c2 010 2 c3 M MADE IN TAIWAN CE 01 2 FM2 zBB CN2 PCM Series User Manual 46 8 3 2 Wiring The PCM 24R1TP uses a wired cable to connect from the I O plate tothe mPCle module The PIN assignment is below Description of PIN Use CN1 PIN1 GND PIN9 NC PIN2 V3 3 LAN PIN10 NC PIN3 NC PIN11 LAN MDIO PIN4 NC PIN12 LAN_MDIO PINS LAN_LINK1000 PIN13 LAN_MDI1 PIN6 V1 9 LAN PIN14 LAN MDI1 PIN7 LAN_ACT PIN15 LAN_MDI2 PIN8 LAN LINK100 PIN16 LAN MDI2 1 5 i
25. 4 Real Time Systems GmbH 5 8 2015 Windows Driver Package u blox ubcdcacm2 Mod u blox 4 15 2015 S Windows Driver Package u blox ubcdcacm2 Ports u blox 4 15 2015 Windows Driver Package u blox ubusbmi2 USB 0 u blox 4 15 2015 m Renesas Electronics Corporation Product version 3 0 23 0 Help link http www renesas com products so 2 After a while the uninstallation will be complete Renesas Electronics USB 3 0 Host Controller Driver InstallShield Wizard Uninstall Complete InstallShield Wizard has finished uninstalling Renesas Electronics USB 3 0 Host Controller Driver 63 PCM Series User Manual 10 3 Pin Assignment and Wiring 10 3 1 Pin Assignment The following table and figure shows the pin assignments of the USB connector on the iDoor IO module for PCM 24U2U3 PIN Assignment of USB Type A Connector 9 Pin Description of PIN Use PIN1 VBUS PING SSRX PIN2 D PIN7 GND PIN3 D PIN8 SSTX PIN4 GND PIN9 SSTX PIN5 PCM Series User Manual 64 10 3 2 Wiring The PCM 24U2U3 utilizes wired cable to connect I O plate and mPCle module The PIN assignments are listed below 1 0 board overview Ou CN1 1 I O board to mPCle Cabling Description of P
26. CAN1 eAutomation CAN port CAN2 gt Ports COM amp LPT b D Processors gt Ramdisk b Sound video and game controllers pu System devices b Universal Serial Bus controllers PCM Series User Manual 26 4 3 Jumper and Switch Settings 36 5 mm 325mm 4 Figure 4 1 CAN bus transceiver board silk screen 4 3 1 How to Set Jumpers You configure your card to match the needs of your application by setting jumpers A jumper is the simplest kind of electric switch It consists of two metal pins and a small metal clip often protected by a plastic cover that slides over the pins to connect them To close a jumper you connect the pins with the clip To open a jumper you remove the clip Figure 4 2 How to set the jumpers 4 3 2 Terminator Resistor Setup JP1 You can set the terminator resistor if necessary to match impedance Each port has a separate resistor located on its own transceiver board Table 4 1 PCM 26D2CA Terminator Resistor Jumper Setting Status Value of Terminator Resistor Ohm Pin 2 3 Open mode None Pin 1 2 Close mode 120 Ohms Note is suggested to set the terminator resistor to 120 Ohm to maintain a sat E y dsfactory baud rate performance 27 PCM Series User Manual 4 4 Pin Assignments Figure 4 3 shows the pin assignment for the card s male DB 9 connectors and corre sponding pin assignments of female DB 9 connectors of the cable
27. D2R2 Male DB9 on iDoor bracket Pin RS 232 DCD RxD DIR OOOOO DSR OOOO CTS RI jo jojo BR wo NM gt 3 4 2 PCM 24D2R4 The following table and figure shows the pin assignments of two male DB9 connec tors on the iDoor bracket for PCM 24D2R4 card in RS 422 and RS 485 Modes Table 3 6 PCM 24D2R4 Male DB9 on iDoor Bracket Pin RS 422 RS 485 Tx Data Tx Data 00000 GND O O O O RTS RTS CTS CTS olo NIDIA AJOIN gt 17 PCM Series User Manual 3 4 3 PCM 24D4R2 The following tables and figures show the pin assignments of 1 female DB37 connec tor one the iDoor bracket to male DB9 for PCM 24D4R2 card in RS 232 mode Table 3 7 PCM 24D4R2 Male DB9 on Cable Pin RS 232 1 DCD 2 RxD 1 2 3 4 5 TxD aT OOOOO 5 GND F OOOO 7 RTS 6 7 8 9 8 CTS 9 RI Pin RS 232 Pin RS 232 1 20 3 RI 2 3 DCD 21 3 DTR 3 3 GND 22 3 DSR 4 3 CTS 23 3 RTS 5 3 RxD 24 3 TxD 6 4 RI 25 4 DCD 7 4 DTR 26 4 GND 8 4 DSR 27 4 CTS 9 4 RTS 28 4 RxD 10 4 TxD 29 2 RI 11 2 DCD 30 2 DTR 12 2 GND 31 2 DSR 13 2 CTS 32 2 RTS 14 2 RxD 33 2 TxD 15 1 RI 34 1 DCD 16 1 DTR 35 1 GND 17 1 DTS 36 1 CTS 18 1 RTS 37 1 RxD 19 1 TxD O O O O O O O O O O O O O O O O O OO O O 900000 00000000000 0 37 20 PCM Series User Manual 18
28. DSR DTR and DCD signals short pins 4 and 5 together and please short pins 6 8 and 20 together RS 422 Signal Wiring The RS 422 interface wiring is based on one to one principles The transmit lines on one side connect to the receive lines on the other side and vice versa With RS 422 you can transmit and receive data simultaneously full duplex The connections are as follows Table 3 14 RS 422 DB9 Pin Assignment DTE Male DB 9 Terminal DTE Pin Signal Pin Signal 1 TxD 1 RxD 2 TxD 2 RxD 3 RxD 3 TxD 4 RxD 4 TxD 5 GND 5 GND 6 RTS 6 CTS 7 RTS 7 CTS 8 CTS 8 RTS 9 CTS 9 RTS Terminator Resistors Setup The signals DSR DTR and DCD are shorted internally on the PCM 24D2R4 24D4R4 cards when operating in RS 422 mode A user can solder in termination resistors if necessary for impedance matching The card has two mounting spaces for termination resistors but no resistors are installed at the factory Each pair of signal lines has a separate resistor RxD TxD 21 PCM Series User Manual 3 5 3 RS 485 Signal Wiring The RS 485 standard supports half duplex communication This means that just two wires are needed to both transmit and receive data Handshaking signals such as RTS Request To Send are normally used to control the direction of the data flow and to switch the transmission accordingly In RS 485 mode the PCM 24D2R4 24D4R4 cards automatically sense the direction of t
29. Data Terminal Equipment refers to the device that is leading the communication Examples include PC s terminals and some printers DCE refers to the device being communicated with or controlled Examples include modems DSU s digital service units printers and lab factory equipment In some situations you may be able to get by with just three lines data on TXD a sig nal ground and a handshaking line Examples are printer or plotter connections trou bleshooting and situations where you require only one wire communication Table 3 11 Terminal or PC DTE Connections DB 25 Male DB 25 Male or Female Terminal Pin Signal Pin Signal 2 TxD 3 RxD 3 RxD 2 TxD 4 RTS 5 CTS 5 CTS 4 RTS 6 DSR 20 DTR 7 GND 7 GND 20 DTR 6 DSR 8 DCD 8 DCD Table 3 12 Modem Connections DB 25 Male Modem DCE Pin Signal Pin Signal 2 TxD 3 RxD 3 RxD 2 TxD 4 RTS 5 CTS 5 CTS 4 RTS 6 DSR 20 DTR 7 GND 7 GND 20 DTR 6 DSR 8 DCD 8 DCD PCM Series User Manual 20 3 5 2 For DTE to DCE connections use a straight through cable i e you don t have to reverse lines 2 and 3 lines 4 and 5 and lines 6 and 20 since in general the DCE RS 232 interfaces are reversed themselves Table 3 13 Terminal without Handshake DB 25 Male Terminal PC DTE Pin Signal Pin Signal 2 TxD 3 RxD 3 RxD 2 TxD 4 RTS 5 CTS 7 GND 7 GND 6 DSR 20 DTR 8 DCD Therefore if you are not using CTS RTS
30. IN Use PIN2 NC PIN13 USB3 y TXDP2 PIN3 NC PIN14 GND PIN4 USB3 RXDP1 PIN15 GND PIN5 USB3 RXDN2 PIN16 USB2 DM1 PIN6 USB3 RXDP1 PIN17 USB2 DM2 PIN7 USB3 RXDP2 PIN18 USB2 DP1 PIN8 GND PIN19 USB2 DP2 PIN9 GND PIN20 NC PIN10 USB3 y TXDN1 PIN11 USB3 y TXDN2 PIN12 USB3 y TXDP1 CN1 20 19 USB2_DP2 USB2_DP1 al 17 USB2_DM2 USB2 DM1 16 15 T 14 13 USB3 y TXDP2 USB3 y TXDP1 12 ES 1i USB3 y TXDN2 USB3 y TXDN1 Su nice 8 7 1 USB3 RXDP2 USB3 RXDP1 cs USB3_RXDN2 USB3 RXDN1 ET IE 2 gt PH_10x2H_2 0mm Characteristics 65 PCM Series User Manual VIN1 Internal Power Cabling Description of PIN Use PIN1 VIN 5V 24V PIN3 GND PIN2 VIN 5V 24V PIN4 GND a WB_4H_2 0mm lt Characteristic gt PCM Series User Manual 66 Appendix A PCM 2300MR AE A 1 Initial Inspection kkkkkkkkkkkk kkkk kkkkkkk kkkk kkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkk Program CheckZ cpp Description Demo program for file access ie APIs used GetLogicalDrives fopen_s fscanf_s fprintf A Date t 1432 20313 Advantech Co Ltd fclose J BRR KK kk KKK k k kk k ko ke ke ke kk kk OK 2 2 2 222 222 22222 2 2 2 2 2 2 2 202 22 2 2222 2 2 2 KKK include stdafx h include lt windows h gt The default drive letter of NVRAM Disk is Z define DEFAUT HD LETTER Z int tmain int argc TCHAR argv DWORD dw dw GetLogicalDrives char
31. N 120 Ohm between 120 Ohm between Tx Tx Data Data COM 4 OFF Open Default ON 120 Ohm between Invalid Rx Rx OFF Open Default PCM Series User Manual 3 3 3 3 1 3 3 2 3 3 3 Driver Setup amp Installation Introduction This chapter describes the driver installation configuration and removal procedures for the for the afore mentioned Windows operating system We strongly recommend that you install the software driver before you install the hardware into your system since this will guarantee a smooth and trouble free installation process Driver Setup Windows operating system supports COM1 to COM256 meaning up to 256 serial ports In order to fully utilize the advanced features of Windows operating system such as multi process and multi thread pure 32 bit Windows 2K XP Vista 7 and oth ers as afore indicated device drivers are provided for the PCI PCle communication cards All these drivers conform to the Win32 COMM API standard Steps for Operating System Driver Setup Before you install the card into your system we recommend you install the driver first Follow the steps below for the PCI PCle communication cards windows operat ing system driver installation 1 Insert your companion DVD ROM disc into your DVD ROM drive 2 Double click the exe file from the DVD ROM then the driver will begin to setup For example PCM 24DxRx Driver xx exe ver InstallShield Wizard Preparing Setup Please wait w
32. User Manual 9 3 Pin Assignment and Wiring 9 3 1 Pin Assignment The following table and figure shows the pin assignments of the LANs connector on the iDoor IO module for PCM 24R2PE and PCM 24R2GL Description of PIN Use PIN1 MDIO PIN7 MDI3 PIN2 MDIO PIN8 MDI3 PIN3 MDI1 PIN9 LED3_LINK1000 PIN4 MDI2 PIN10 LED2_LINK100 PINS MDI2 PIN11 V3 3SB PIN6 MDI1 PIN12 LED1_ACT eft IED g LED3 LINK1000 10 LED2 LINK100 11 a 12 LED1 ACT amp a cds H1 H2 NV GND_F3 GND_F2 PCM Series User Manual 56 9 3 2 Wiring PCM 24R2PE and 24R2GL is using wired cable to connect from I O plate to mPCle module The PIN assignment is below Description of PIN Use PIN1 V3 3SB PIN16 LANO LED2 LINK100 PIN2 PLTRST PIN17 LAN1 LED1_ACT PIN3 MDI_1_3N PIN18 LANO_LED1_ACT PIN4 MDI 1 2P PIN19 GND PIN5 MDI 1 3P PIN20 GND PING MDI 1 2N PIN21 MDI 0 2P PIN7 GND PIN22 MDI 0 3P PIN8 GND PIN23 MDI 0 2N PIN9 MDI 1 ON PIN24 MDI 0 3N PIN10 MDI 1 1N PIN25 GND PIN11 MDI 1 OP PIN26 GND PIN12 MDI 1 1P PIN27 MDI 0 OP PIN13 LAN1_LED3_LINK1000 PIN28 MDI 0 1N PIN14 LANO_LED3_LINK1000 PIN29 MDI_0_ON PIN15 LAN1_LED2_LINK100 PIN30 MDI 0 1P O10 uU L 0000000000 T Md ES BE toy esse L es 00000000000
33. aged or it fails to meet specifications notify our service department or your local sales representative immediately Also notify the carrier Retain the shipping carton and packing material for inspection by the carrier After inspection we will make arrangements to repair or replace the unit When you handle the PCM 24U2U3 remove it from its protective packaging by grasping the rear metal panel Keep the anti vibration packing Whenever you remove the card from the PC store it in this package for protection Warning Discharge your body s static electric charge by touching the back of the grounded chassis of the system unit metal before handling the board A You should avoid contact with materials that hold a static charge such as plastic vinyl and Styrofoam Handle the board only by its edges to avoid static damage to its integrated circuits Avoid touching the exposed cir cuit connectors We also recommend that you use a grounded wrist strap and place the card on a static dissipative mat whenever you work With it Note 1 Power requirements 5 24 VDC 10 W Max 2 Power consumption 5 V 900 mA Max 3 Full size PCI Express Mini Card Revision TM 2 0 4 With xHCI specification compliance 5 Universal Serial Bus 3 0 specification Rev 1 0 compliant 6 Operating Temperature 20 60 C 4 140 F PCM Series User Manual 60 10 2 Driver Setup amp Installation Advantech Device Manager Installation 10 2 1 Introduction
34. ager Advanced Network Services Windows PowerShell Module Intel R Network Connections SNMP Agent IS Feature Description 4 Select Install and start to installation Ready to Install the Program The wizard is ready to begin installation Click Install to begin the installation If you want to review or change any of your installation settings click Back Click Cancel to exit the wizard 5 Driver is being installed 3 Intel R Network Connections Install Wizard Installing Intel R Network Connections E ai D The program features you selected are being installed nte Please wait while the install wizard installs Intel R Network Connections This may take several minutes Copying driver files This may take a few minutes please wait Cancel PCM Series User Manual 44 6 T Select Finish to complete the installation Install wizard Completed properties of the network adapters To access new features open Device Manager and view the En c Back After the hardware has been installed the card will be automatically detected Open Device Manager to check it ge File Action View Help mie 4 gy DQA PC b 4M Computer gt w Disk drives MY Display adapters gt os Human Interface Devices gt cg IDE ATA ATAPI controllers p m Keyboards b n Mice and other
35. al support if you need additional assistance Please have the following information ready before you call Product name and serial number Description of your peripheral attachments Description of your software operating system version application software etc A complete description of the problem The exact wording of any error messages iii PCM Series User Manual Warnings Cations and Notes Warning Warnings indicate conditions which if not observed can cause personal injury Caution Cautions are included to help you avoid damaging hardware or losing data e g IN There is a danger of a new battery exploding if it is incorrectly installed Do not attempt to recharge force open or heat the battery Replace the battery only with the same or equivalent type recommended by the man ufacturer Discard used batteries according to the manufacturer s instructions Note Notes provide optional additional information Document Feedback To assist us in making improvements to this manual we would welcome comments and constructive criticism Please send all such in writing to support advantech com Packing List Before setting up the system check that the items listed in each chapter are included and in good condition If any item does not accord with the table please contact your dealer immediately PCM Series User Manual iv Safety Instructions 10 11 12 13 14 15 16
36. ation packing Whenever you remove the card from the PC store it in this package for protection Warning Discharge your body s static electric charge by touching the back of the grounded chassis of the system unit metal before handling the board A You should avoid contact with materials that hold a static charge such as plastic vinyl and Styrofoam Handle the board only by its edges to avoid static damage to its integrated circuits Avoid touching the exposed cir cuit connectors We also recommend that you use a grounded wrist strap and place the card on a static dissipative mat whenever you work With it 7 2 Driver Setup amp Installation Advantech Device Manager Installation Advantech s PCM 23C1CF is a SATAII 3G Sec to CFast interface for storage The driver is on the storage device and no need driver is required PCM Series User Manual 38 7 3 7 3 1 Pin Assignment and Wiring Pin Assignment The following table and figure shows the pin assignments of CFast connector on the iDoor IO module for PCM 23C1CF Description of PIN Use CN2 CFast Connector PINS1 GND PINPC6 NC PINS2 SATA TX PINPC7 GND PINS3 SATA TX PINPC8 NC PINS4 GND PINPC9 NC PINS5 SATA RX PINPC10 NC PINS6 SATA RX PINPC11 NC PINS7 GND PINPC12 NC PINPC1 NC PINPC13 3 3V PINPC2 GND PINPC14 3 3V PINPC3 NC PINPC15 GND PINPC4 NC PINPC16 GND PINPC5 NC PINPC17 NC cs ais C 9000000 2000000 39
37. ch DEFAUT HD LETTER int n char pathInOut 50 0 char bufferOut 0123456789abcdefghijklmnopqrstuvwxyz char bufferInput 50 0 errno t ErrRet 0 FILE fp r NULL FILE fp w NULL Step 1 To check if Z drive exists printf nStep 1 Check c Drive n ch if dw 0 amp amp dw gt gt n 0 printf There is a c drive n ch else printf There is NO c drive n ch exit 1 Step 2 Prepares the path for Input and Ouput printf nStep 2 Prepares the path Nate sprintf s pathInOut 100 c inout txt ch printf PATH for Input and Output s n pathInOut Step 3 Writes something to a file printf nStep 3 Writes something to a file n ErrRet fopen s amp fp w pathInOut w if ErrRet 0 printf Failed to open s n pathInOut exit 1 else Output data to the text file PCM Series User Manual 68 fprintf fp w ss bufferOut Close file handle fclose fp w fp w NULL Step 4 Reads a file and displays its content on the screen printf nStep 4 Reads a file and ErrRet fopen s amp fp r pathInOut if ErrRet 0 printf Failed to open s n pathInOut exit 1 else Reads the content and shows it to console fscanf s fp r ss bufferInput printf sWn bufferInput Close file handle fclose fp r fp r NULL system pause return 0
38. ed It should be free of marks and scratches and in perfect working order when received As you unpack the PCM 23U1DG check for signs of shipping damage damaged box scratches dents etc If it is damaged or it fails to meet specifications notify our service department or your local sales representative immediately Also notify the carrier Retain the shipping carton and packing material for inspection by the carrier After inspection we will make arrangements to repair or replace the unit When you handle the PCM 23U1DG remove it from its protective packaging by grasping the rear metal panel Keep the anti vibration packing Whenever you remove the card from the PC store it in this package for protection Warning Discharge your body s static electric charge by touching the back of the grounded chassis of the system unit metal before handling the board A You should avoid contact with materials that hold a static charge such as plastic vinyl and Styrofoam Handle the board only by its edges to avoid static damage to its integrated circuits Avoid touching the exposed cir cuit connectors We also recommend that you use a grounded wrist strap and place the card on a static dissipative mat whenever you work With it Driver Setup amp Installation Advantech Device Manager Installation The Advantech PCM 23U1DG is an internal USB with locked interface for security dongle disk or storage The driver is based on the storage and there is no
39. ed It should be free of marks and scratches and in perfect working order when received As you unpack the PCM 2300TP check for signs of shipping damage damaged box scratches dents etc If it is damaged or it fails to meet specifications notify our service department or your local sales representative immediately Also notify the carrier Retain the shipping carton and packing material for inspection by the carrier After inspection we will make arrangements to repair or replace the unit When you handle the PCM 2300TP remove it from its protective packaging by grasping the rear metal panel Keep the anti vibration packing Whenever you remove the card from the PC store it in this package for protection Warning Discharge your body s static electric charge by touching the back of the grounded chassis of the system unit metal before handling the board A You should avoid contact with materials that hold a static charge such as plastic vinyl and Styrofoam Handle the board only by its edges to avoid static damage to its integrated circuits Avoid touching the exposed cir cuit connectors We also recommend that you use a grounded wrist strap and place the card on a static dissipative mat whenever you work With it Driver Setup amp Installation Advantech Device Manager Installation For details about Advantech s PCM 2300TP Driver Setup and Device Manager Installation refer to Advantech PCA TPM O0A1E product information on the DVD
40. he data flow and switch the trans mission direction no handshaking is necessary This means a user can build an RS 485 network with just two wires This RS 485 control is completely transparent to the user The software written for half duplex RS 232 works without any modification D T E D T E D T E RS 485 RS 485 RS 485 Transceiver Transceiver Transceiver Data Data i Data Data Data 1 E 120 Ohm Ohm Figure 3 1 RS 485 Wiring Topology Termination Resistor Setup You can install termination resistors if necessary for impedance matching The card has mounting spaces for termination resistors but no resistors are installed at the factory Depending on your application you may need to solder in a single resistor to handle the DATA DATA pair and a corresponding resistor on the other end of the connection The value of the resistor should equal the characteristic impedance of the signal wires approximately 120 Ohms or 300 Ohms PCM Series User Manual 22 PCM 26D2CA 2 Ports Isolated CANBus mini PCIe CANOpen DB9 This chapter covers the pin assignment for the CAN connec tor and the wiring of the two transmission wires Sections include E Initial Inspection E Driver and Advantech Device Manager Installation E Jumper and Switch Settings B Pin Assignment E Wiring 4 1 Initial Inspection You should find the following items inside the shipping package Mini
41. hile the InstallShield Wizard prepares the setup Advantech PCI ICOM Driver Setup is preparing the InstallShield Wizard which will guide you through the rest of the setup process Please wait we m o Cancel 15 PCM Series User Manual 3 3 4 Driver Uninstall 1 In the Control Panel click Advantech PCI ICOM Driver then uninstall F6 Add or Remove Programs m iol x om si Currently installed programs Show updates Sort by Name x Change or nn B Advantech DiagAnywhere Server Size 0 11MB Programs f Advantech PCI ICOM Driver w Click here For support information Add New To change this program click Change Programs m Add Remove Windows Components 2 Choose Remove then click Next then start to remove all installed compo nents Welcome Modify repair or remove the program Welcome to the Advantech PCI ICOM Driver Setup Maintenance program This program lets you modify the current installation Click one of the options below Modify 18 Select new program features to add or select currently installed features to remove Repair fF Reinstall all program features installed by the previous setup E Remove all installed features PCM Series User Manual 16 3 4 Pin Assignments 3 4 1 PCM 24D2R2 The following table and figure shows the pin assignments of two male DB9 connec tors on the iDoor bracket for PCM 24D2R2 card in RS 232 Mode Table 3 5 PCM 24
42. m Hilscher Referto DVD Refer to DVD PCM 23U1DG AE Chapter 5 Refer to DVD Referto DVD Refer to DVD PCM 2300TP AE Chapter 6 Refer to Advantech PCA TPM 00A1E product information for Driver Datasheet Manual and Startup PCM 23C1CF AE Chapter 7 Refer to DVD Refer to DVD Refer to DVD PCM 24R1TP AE Chapter 8 Refer to DVD Referto DVD Refer to DVD PCM 24R2PE AE chapterg Referto DVD Referto DVD Refer to DVD PCM 24R2GL AE PCM Series User Manual PCM 2300MR AE 2MB MRAM mini PCle card This chapter shows how to install the driver and Advantech Device Manager Sections include B Initial Inspection E Driver Setup amp Installation Advantech Device Manager Installation Format 2 1 Initial Inspection You should find the following items inside the package Mini PCle communication interface card W Industrial Communication Driver Utility and mini PCle communication card user s manual in PCM 2000 DVD ROM The PCM 2300MR was carefully inspected mechanically and electrically before it was shipped It should be free of marks and scratches and in perfect working order when received As you unpack the PCM 2300MR check for signs of shipping damage damaged box scratches dents etc If it is damaged or it fails to meet specifications notify our service department or your local sales representative immediately Also notify the carrier Retain the shipping carton and packing mate
43. marks and scratches and in perfect working condition on receipt As you unpack check for any signs of shipping damage damaged box scratches dents etc Should any damage is found or it fail to meet specifications please notify our service department or your local sales representative immediately Also the car rier should be notified Retain the shipping carton and packing material for further inspections by the carrier After inspection we will make arrangements to repair or replace the unit When you handle the communication card remove it from its protective packaging by grasping the rear metal panel Keep the anti vibration packaging for further storage as the card was removed from the PC Warning Discharge your body s static electric charge by touching the back of the grounded chassis of the system unit metal before handling the board A You should avoid contact with materials that hold a static charge such as plastic vinyl and Styrofoam Handle the board only by its edges to avoid static damage to its integrated circuits Avoid touching the exposed circuit connectors We also recommend that you use a grounded wrist strap and place the card on a static dissipative mat whenever you work with it PCM Series User Manual 12 3 2 Jumper and Switch Settings 3 2 1 PCM 24D2R4 Settings OOOO 0000 m smo 000 000000000 Table 3 1 Master Sla
44. ment Please read the following license agreement carefully INTEL SOFTWARE LICENSE AGREEMENT IMPORTANT READ BEFORE COPYING INSTALLING OR USING Do not copy install or use this software and any associated materials collectively the Software provided under this license agreement Agreement until you have carefully read the following terms and conditions By copying installing or otherwise using the Software you agree to be bound by the terms of this Agreement If you do not agree to the terms of this Agreement _ e mnt ann inntinii arunnthn Cafhunra I accept the terms in the license agreement I do not accept the terms in the license agreement Back Next gt Cancel 5 Select Driver for Windows Device Manager Intel PROSet to continue the installation Setup Options Select the program features you want installed Install Drivers V Intel R PROSet for Windows Device Manager V Advanced Network Services E Windows PowerShell Module Intel R Network Connections SNMP Agent PCM Series User Manual 52 6 Select Install and start to installation Ready to Install the Program The wizard is ready to begin installation Click Install to begin the installation If you want to review or change any of your installation settings dick Back Click Cancel to exit the wizard 7T Select Finish to complete the installation Install wizard Completed
45. n 38 Pin Assignment and Wiring san 39 1 3 1 Pin Assignment ges faune ii 39 p MB 40 PCM 24R1TP AE 41 Initial Irispectlop 22 ie to een ie an ai 42 Driver Setup amp Installation Advantech Device Manager Installation 43 8 2 1 Introduction Henne ie 43 8 2 2 Installation HR een 43 Pin Assignment and Wiring mn 46 8 3 1 Pin ASsignment 5 eie inen Fal ede eiae tec 46 S MERCI EP 47 PCM 24R2PE AE 49 PCM 24R2GL AE 49 Initial Irispectlopi i tete riter entendent 50 Driver Setup amp Installation Advantech Device Manager Installation 51 92 1 lrntrodUuCtiQna zione eee eee zac 51 9 22 Installation anne een 51 viii 9 3 Chapter 10 10 1 10 2 10 3 Appendix A A 1 A 2 9 2 3 Uninstall nicer aeree ana 54 Pin Assignment and Wiring men 56 9 3 1 Pin Assignment iere etre neces cath 56 9 3 2 Wiring emen enne 57 PONI 24020 Sierre DD am Bertin 60 Driver Setup amp Installation Advantech Device Manager Installation 61 10 2 1 Introduction sise osent teet ma 61 10 2 2 Installation io enis 61 10 2 3 Uninstall ae ul andre taedet is 63 Pin Assignment and Wiring ssen mm 64 10 3 1 PinrAssignmelt uio ec renti ib Pte racione 64 10 3 2 Wiring es
46. nge or Repair Tum Windows features on or off Name E Version Name jme Network Connections instal Wizard D ruines 71 Pro 7 Intel Power Thermel Util Welcome to the install wizard for Intel R a N 12 EINE Network Connel Network Connections PTT Ex Intel R Thermal Analysil 34 Intel Graphics Driver 361501073 M Inte Trusted Brectiol 1002050 Apes USB30 cXtensial Int Newark Connection iil ES os Do you went to close the following epplications and continue with Intel Network Connections software configuration Microsoft Management Console Intel Product version 194 310 Support link http vwiidntelcom ink htta www intel com Sce 243 MB PCM Series User Manual 54 3 n Remove Options panel just select Remove to continue the process Remove Options Select the program features you want to remove Remove V Drivers YlIntel R PROSet for Windows Device Manager V Advanced Network Services Feature Description 4 Remove Options Select the program features you want to remove Remove V Drivers Intel R Network Connections Remove Software Are you sure you want to remove the selected components from your A computer Yes No 5 Select Finish to complete the uninstallation process Install wizard Completed The install wizard has successfully uninstalled the selected features 55 PCM Series
47. ocessors H E Ramdisk Sound video and game controllers Storage volumes System devices H lt Universal Serial Bus controllers PCM Series User Manual 8 2 Select Settings page and then click Clear data button to format MRAM disk Advantech NYRAM Disk Device Properties 9 PCM Series User Manual c Jeydeu2 jV HINOO C INOd PCM Series User Manual 10 PCM 24DxRx AE PCM 24D2R4 AE PCM 24D2R2 AE PCM 24D4R4 AE PCM 24D4R2 AE Industrial Serial Communication Cards This chapter covers inspection and installation of hardware and drivers Sections include E Ordering Information E Initial Inspection E Jumper and Switch Settings E Driver Setup amp Installation B Pin Assignment E Wiring Ordering information Product Description PCM 24D2R2 AE 2 Ports Isolated RS 232 mini PCle DB9 PCM 24D2R4 AE 2 Ports Isolated RS 422 485 mini PCle DB9 PCM 24D4R2 AE 4 Ports Non lsolated RS 232 mini PCle DB37 PCM 24D4R4 AE 4 Ports Non lsolated RS 422 485 mini PCle DB37 3 1 Initial Inspection 1 PCM 2400 Communication card including A PCM 2400 mini PCle Card B O plate C Wire cable D DB37 to DB9 4 ports cable For PCM 24D4R4 AE only 2 PCM 2000 DVD ROM including A User manual B Industrial Communication Driver We carefully inspect our PCM 2400 communication card mechanically and electri cally before shipping It should be free of
48. personnel authorized by Advantech or which have been subject to misuse abuse accident or improper installation Advantech assumes no liability under the terms of this warranty as a consequence of such events Because of Advantech s high quality control standards and rigorous testing most of our customers never need to use our repair service If an Advantech product is defec tive it will be repaired or replaced at no charge during the warranty period For out of warranty repairs you will be billed according to the cost of replacement materials service time and freight Please consult your dealer for more details If you think you have a defective product follow these steps 1 Collect all the information about the problem encountered For example CPU speed Advantech products used other hardware and software used etc Note anything abnormal and list any onscreen messages you get when the problem OCCUIS 2 Call your dealer and describe the problem Please have your manual product and any helpful information readily available 3 f your product is diagnosed as defective obtain an RMA return merchandize authorization number from your dealer This allows us to process your return more quickly 4 Carefully pack the defective product a fully completed Repair and Replacement Order Card and a photocopy proof of purchase date such as your sales receipt in a shippable container A product returned without proof of the purchase date i
49. rial for inspection by the carrier After inspection we will make arrangements to repair or replace the unit When you handle the PCM 2300MR remove it from its protective packaging by grasping the rear metal panel Keep the anti vibration packing Whenever you remove the card from the PC store it in this package for protection Warning Discharge your body s static electric charge by touching the back of the grounded chassis of the system unit metal before handling the board A You should avoid contact with materials that hold a static charge such as plastic vinyl and Styrofoam Handle the board only by its edges to avoid static damage to its integrated circuits Avoid touching the exposed circuit connectors We also recommend that you use a grounded wrist strap and place the card on a static dissipative mat whenever you work with it PCM Series User Manual 4 2 2 Driver Setup amp Installation Advantech Device Manager Installation Advantech provides WDM MRAM driver that allows you to configure your hardware and store the settings in your Windows registry You must install the WDM MRAM driver if you want to add and manage Advantech MRAM cards Follow the steps below to install Advantech MRAM WDM Driver 1 Select Next to continue the installation AdvNVRAMDisk InstallShield Wizard x Welcome to the InstallShield Wizard for AdvNVRAMHDisk The InstallShield Wizard will install amp dv NVRAMDisk on your computer To con
50. s not eligible for warranty service 5 Write the RMA number visibly on the outside of the package and ship it prepaid to your dealer Part No 2003P20000 Edition 1 Printed in Taiwan May 2015 PCM Series User Manual ii Declaration of Conformity CE This product has passed the CE test for environmental specifications when shielded cables are used for external wiring We recommend the use of shielded cables This kind of cable is available from Advantech Please contact your local supplier for ordering information FCC Class A Note This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Opera tion of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense Technical Support and Assistance 1 Visit the Advantech web site at www advantech com support where you can find the latest information about the product 2 Contact your distributor sales representative or Advantech s customer service center for technic
51. t does not work well or you cannot get it to work according to the user s manual The equipment has been dropped and damaged The equipment has obvious signs of breakage DO NOT LEAVE THIS EQUIPMENT IN AN ENVIRONMENT WHERE THE STORAGE TEMPERATURE MAY GO BELOW 20 C 4 F OR ABOVE 60 C 140 F THIS COULD DAMAGE THE EQUIPMENT THE EQUIPMENT SHOULD BE IN A CONTROLLED ENVIRONMENT CAUTION DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY REPLACED REPLACE ONLY WITH THE SAME OR EQUIVALENT TYPE RECOMMENDED BY THE MANUFACTURER DISCARD USED BATTERIES ACCORDING TO THE MANUFACTURER S INSTRUCTIONS The sound pressure level at the operator s position according to IEC 704 1 1982 is no more than 70 dB A DISCLAIMER This set of instructions is given according to IEC 704 1 Advantech disclaims all responsibility for the accuracy of any statements contained herein V PCM Series User Manual Safety Precaution Static Electricity Follow these simple precautions to protect yourself from harm and the products from damage B To avoid electrical shock always disconnect the power from your PC chassis before you work on it Don t touch any components on the CPU card or other cards while the PC is on m Disconnect power before making any configuration changes The sudden rush of power as you connect a jumper or install a card may damage sensitive elec tronic components PCM Series User Manual vi Contents Chapter 1 zx N gt Chapter
52. tinue click Next Back Cancel 2 Select Install to continue the installation AdvNYRAMDisk InstallShield Wizard Ready to Install the Program The wizard is ready to begin installation Click Install to begin the installation If you want to review or change any of your installation settings click Back Click Cancel to exit the wizard InstallShield 5 PCM Series User Manual 3 After a while the installation will be complete AdvNVRAMDisk InstallShield Wizard InstallShield Wizard Complete The InstallShield Wizard has successfully installed AdvNVRAMDisk Click Finish to exit the wizard Back Cancel 4 Select OK to Restart your computer Restarting Windows Setup has finished copying files to your computer Before you can use the program you must restart your computer Select one of the following options and click OK to finish setup Yes want to restart my computer now No will restart my computer later PCM Series User Manual 6 5 After the physical hardware has been installed the card will be automatically detected an Device Manager File Action View Help gt BES BE A lt Rd E a OEM 03D5AGATZAIM M Advantech 14G Onboard Devices 8 Advantech NYRAM Disk Devices ES Advantech NVRAM Disk Device 3 Computer ee Disk drives 2 Display adapters Human Interface Devices E IDE ATA ATAPI controllers gt Keyboards y Mice and other pointing
53. u work with it PCM Series User Manual 24 4 2 Advantech provides WDM CAN driver that allows you to configure your hardware and store the settings in your Windows registry You must install the WDM CAN driver if you want to add and manage Advantech CAN cards Please follow the steps below to install Advantech CAN WDM Driver 1 Select Next to continue the installation Welcome to Advantech CAN WDM Driver Setup program The InstallShield Wizard will install Advantech CAN WDM Driver on your computer To continue click Next InstallShield Maintenance Complete InstallShield Wizard has finished performing maintenance operations on Advantech CAN WDM Driver Qi Yes want to restart my computer now No will restart my computer later Remove any disks from their drives and then click Finish to complete setup InstallShield 25 PCM Series User Manual 3 After the physical hardware has been installed the card will be automatically detected e Igni ll B em e 4 4 UNO2184G gt Advantech IAG Onboard Devices 4 Advantech ICOM CAN cards Lu amp ADVANTECH C302 CAN card 2 PORT support CANopen b 4 Computer b Disk drives D x Display adapters gt gm IDE ATA ATAPI controllers b b 4 Keyboards A Mice and other pointing devices gt ME Monitors gt Network adapters gt EB Portable Devices 4 Ports Advantech PCI amp ISA CAN Ports Automation CAN port
54. ure 4 1 CAN bus transceiver board silk screen 27 4 3 1 Howto Set Jumpers sssssssssssssseseneen nennen 27 Figure 4 2 How to set the jumpers 27 4 3 2 Terminator Resistor Setup JP1 27 Table 4 1 PCM 26D2CA Terminator Resistor Jumper Setting 27 Pin AsSIgAments i ice Bee ee 28 Figure 4 3 PCM 26D2CA DB 9 connector pin assignments 28 Figure 4 4 PCM 26D2CA DB 9 connector schematics 28 Table 4 2 PCM 26D2CA Pin Description 28 WING sees 29 Figure 4 5 FPC cable wiring se 29 Figure 4 6 Wiring on module side 29 PCM 23U1DG AE 31 Initial Inspection coder Ert Ee nite mari ec rex e e be E enn ded 32 Driver Setup amp Installation Advantech Device Manager Installation 32 Pin Assignment and Wiring enn 33 5 39 1 Pin Assigniment eint iur iie eie adis 33 5 3 2 WIIG iiio ro eitis Pod ae URP Red Uo date anni 33 PCM 2300TP AE OO Initial Inspection is ant tnn ie o ne hen d ed MARE idan 36 Driver Setup amp Installation Advantech Device Manager Installation 36 Pin Assignment and Wiring us 36 POMZICICP AE OT Initial Inspection e 38 Driver Setup amp Installation Advantech Device Manager Installatio
55. vantech PC A Computer cs Disk drives VK Display adapters Human Interface Devices IDE ATA ATAPI controllers amp Keyboards M Mice and other pointing devices amp Monitors 4 jy Other devices Di Ethernet Controller Di Ethernet Controller a Ethernet Controller Din Ethernet Controller Ethernet Controller 1j Ethernet Controller T Ports COM amp LPT DD Processors X Sound video and game controllers 4 V System devices gM ACPI Fan qW ACPI Fixed Feature Button gM ACPI Power Button 1M ACPI Sleep Button eM ACPI Thermal Zone 2 Getthe driver from the DVD or Intel website click it then run the driver and select I agree to continue the installation Welcome to the install wizard for Intel R Network Connections Intel R Network Connections Do you want to close the following applications and continue with Intel R Network Connections software configuration Microsoft Management Console 51 PCM Series User Manual 3 Select Next to continue installation Welcome to the install wizard for Intel R Network Connections intel Installs drivers Intel R Network Connections and Advanced Networking Services WARNING This program is protected by copyright law and international treaties 4 Select I accept the terms in the license agreement to continue installation and click Next ET Intel R Network bg inten ny ven License Agree
56. ve Settings Jumper Pin Description 1 2 RS 422 Master 2 3 RS 485 RS 422 Slave Default CN2 Table 3 2 Terminal Resistor Settings Switch Terminal Resistor Switch Setting SW1 1 D on 120 ohm 2 RX on 3 4 off 3 D on 300 ohm 4 RX on 1 2 off 13 PCM Series User Manual 3 2 2 PCM 24D4R4 Settings 5 a E 1000000000000000000007 5000 gnonoonoonononoannng Doooo O 000000000000000000 000000000000000000 Table 3 3 Master Slave Settings COM Port Switch Pin Setting Description ON RS 422 Master COM 1 OFF RS 485 RS 422 Slave Default ON RS 422 Master COM 2 swt OFF RS 485 RS 422 Slave Default COM 3 ON RS 422 Master OFF RS 485 RS 422 Slave Default ON RS 422 Master COM 4 OFF RS 485 RS 422 Slave Default Table 3 4 Terminal Resistor Settings COM Port Switch Pin Setting RS 422 Description RS 485 Description 120 Ohm between 120 Ohm between Tx Tx Data Data COM 1 OFF Open Default ON 120 Ohm between Invalid Rx Rx sw2 OFF Open Default ON 120 Ohm between 120 Ohm between Tx Tx Data Data COM2 OFF Open Default ON 120 Ohm between Invalid Rx Rx OFF Open Default ON 120 Ohm between 120 Ohm between Tx Tx Data Data OFF O Default COM 3 pen Default ON 120 Ohm between Invalid Rx Rx SW3 OFF Open Default O

User Manual PCM-2000 Series

Contents

Download Pdf Manuals

Related Search

Related Contents