easyRAID Q16PS-F4R3 Hardware User Manual
Contents
1. 1 4 5 6 e 9 3 al ULT TER m Eu RA O b CFOG ga rege E C e e 15 14 13 12 11 2 3 10 9 8 7 No Name Description Cooling fan 1 System cooling fan 2 Host Port 2 Connects to the host server Secondary fibre channel 3 Host Port 1 Connects to the host server Primary fibre channel 4 RS 232 Port Connects to a VT100 terminal or equivalent 5 UPS port Data port for uninterruptable power supply 6 Cooling fan 2 System cooling fan 7 Power Supply 2 Removable redundant power supply 2 8 Power Supply Handle For power supply removal 9 Power Supply AC In Connects to a 100 240 VAC power source 10 Power Supply Switch Switches the power on or off 11 Ethernet Port Used for browser based configuration 12 Expansion Port Used for JBOD expansion 13 Power Supply 1 Removable redundant power supply 1 14 Power Supply Handle For power supply removal 15 Power Supply AC In Connects to a 100 240 VAC power source sjusuodwoy uoneunBiuo oiseg c easyRAID Q16PS F4R3 SAS Disk Array Systems This section describes how to install disks in the disk array system 1 Unlock the front panel door then pull it open 2 Push the button A to release the disk tray handle Pull the handle B to release the tray sysiq Buije su uoneunByuo seg c 3 Align the rear of the disk with the rear of the disk tray2. 4 Insert the disk into the disk tray and fix into place with screws supplied with the disk easyRAID Q16PS F4R3 SAS Disk Array Systems 5 Slide the disk tray back into the empty slot A then slowly close the disk tray handle B 6 Repeat steps 2 to 5 until all of the required disks have been installed 7 Push the front panel door closed and lock it Note If you are combining SAS and SATA in the same easyRAID Q16PS FAR3 Recommending DO NOT include SAS and SATA disks in the same column A or DO NOT place a column of SATA disks between two columns of SAS disks B A B SAS SATA sysiq Buije su uoneunByuo oiseg Z suonoeuuo uen uoneun amp iuo 91seg c easyRAID Q16PS F4R3 SAS Disk Array Systems After the required number of disks have been installed external connections to the disk array system must be made This section describes how to make all of the necessary connections The disk array system has dual fibre channel interfaces Refer to the following sections to make host interface connections The easyRAID Q16PS F4R3 has dual 4 Gbit fibre channel interfaces Each interface can be used with optical or copper transceivers and cables Follow these instructions to make optical connections 1 Insert the LC Optical SFP transceiver A in to the easyRAID Q16P
3. DIMM with a maximum capacity of 2 GB Follow these instructions to upgrade the memory 1 Loosen the screws holding the controller cage in place slide the controller cage out of the chassis 2 Pullthe DIMM retaining clips away from the DIMM the DIMM springs out of the socket Remove the DIMM T e 3 Gently push the new DIMM into the socket then push the corners of the DIMM down The DIMM is secured by the DIMM retaining clips Push the controller cage back in lower the handle and tighten the retaining screws Note The DIMM module will fit in only one direction Do not force the DIMM into place 17 Aowa Bui pei dn soueusjureyy c a npow NW e Buroejdes eoueueojure A c easyRAID Q16PS FAR3 SAS Disk Array Systems When one of the FAN module fails the massage FANx Fail appears on the LCD panel where x refers to power supply 1 or 2 and an audible alert sounds Note of Turn off the audible alert by pressing the Up and Down function buttons on the front panel twice simultaneously 1 Identify the FAN module that has failed loosen the retaining screws slide it out of chassis Bann SEO Bone Q y e 18 Item Specification CPU Memory AMCC PPC 440SP DDRII 240pin DIMM ECC support Host Interface 4 Gb
4. and optical cable the following transmission distances can be achieved Component Optical SFP Transceiver LC Optical Cable Short Wave Long Wave Maximum Cable Length 50m 10 Km easyRAID Q16PS F4R3 supports up to sixteen of quantities of SAS 3Gbps and SATA II 1 5Gbps 3Gbps disks All disk tray is hot swappable sjueuieJinbas uiejs S L easyRAID Q16PS FAR3 SAS Disk Array Systems VT100 Terminal Settings Refer to the following table for a summary of VT100 terminal settings required to com municate with the disk array system Refer to your system manual for instructions on setting up the VT100 terminal settings Item Required Setting Connection Serial Port COM1 or COM2 Protocol RS232 Asynchronous Cabling Null Modem cable Baud Rate 115200 Data Bits 8 Stop Bit 1 Parity None easyRAID Q16PS F4R3 supports DHCP Dynamic Host Configuration Protocol to get a IP address or a default IP is 192 168 0 1 You could find it from LCD scrolling easyRAID Q16PS F4R3 had embedded CGI based GUI graphic user interface management interface can be easily accessed through a web browser 2 Basic Configuration This chapter describes disk array system connections and disk installation Contact your supplier if any of the following items are missing or damaged Caution A The disk array system is heavy Be careful when lifting and moving it Power Cables ig er Fix Screw pack
5. length to fit in your rack 3 Boltthe rails into the rack using the rack bolts supplied with your rack EL i You will need four nuts and bolts not included for each rail two at the front and two at the back 4 Tighten the locking screws when they are the correct length 5 Slide the disk array system into the rack and bolt it into place with the supplied fixing screws E SIRES I Ll Ht 8 oM I al S I Caution This product is heavy Attempting to install the disk array system in a rack by yourself could result in injury or damage to the product 13 yoey e ul Bununojy uoneun iuo oiseg c yoey e ul Bununoyy uoneunBijuo 91seg c easyRAID Q16PS F4R3 SAS Disk Array Systems Follow these instructions to fit the rail extenders if required 1 If required bolt the rail extenders into place as shown using the small bolts pro vided 2 Slide the disk array system into the rack and bolt it into place with the supplied fixing screws Imm h I SO re WERE Note The rail extenders may be required to allow the disk array system room for the front door to open correctly 14 A disk failure is indicated when the P
6. Fibre Channel x 2 Disk Interface Temperature Sensor 3 Gb SAS x 16 3 on controller 7 on backplane Dimensions 132 mm H x 485 mm W x 574 mm D Weight 24 Kg without disks Management IO connector 1 x RS 232 COM port 1x RJ 45 LAN port 10 100 Mbps JBOD Expansion Yes optional Battery Backup Module Yes optional FAN Turbine FAN x 2 Hot Swapable Power Supply Redundant 1 1 460 Watt 100 240 VAC 47 63 Hz 6 3A 10 Over voltage current power and short circuit protection LED indicates power status Output 5V 3 3V 12V Operating Enviroment Temperature 5 C 40 C Humidity 10 85 non condensing Warranty 3 year warranty Safety UL CUL CB EMC FCC CE C Tick BSMI
7. M5 Fix Screw pack M6 Front Panel Keys T S MN 9 7 By ES ma MO p Fix Screw pack HDD S crew pack UNC 7110 32 RS 232 Cable sjueuodwoy uoneinByuoy oiseg c easyRAID Q16PS F4R3 SAS Disk Array Systems 30803 2888 303080809808 480308080803098098 So 8o 98988 3030280302030 a 88898989898 898989898 2208080808009 38888800 228888888 388888288888888888888888 9989898985898 9989898 3 OYES 98989 S9898989898989898 999899989999 333338 33 o9 382828282888 898 S308080808080S80l80S0S0 338 9 S89898989b989888888888895895895B8 388828883 388888 38 gogegogooboes2ea2o O O9 30939393 3939393 OoOo9Oo9Oo9o090909 999999999999999999999999999999999999999999999 o9e9SeSesBSsSPSSSPSSSPS 9SoSoSoSo8o898989898989898989898989898989898989898989 39 32323882 ose poso 323223 Sata 3333388 2333333333388 93333338 3338 e 88888 989899999999 2308 232 2308 ogogogogogcBogobogobogobogogog9g92929299929999g9299992999929999929999299999929992 No Name Description 4 LCD panel Displays warning operating and configuration information 2 Power on indicator Indicates the disk array system power is on 3 Power supply fail indicator Indicates a failed power supply 4 Host computer access indicator Indicates data transfer between the disk array sys tem and the host computer 5 Up function button Moves up in the LCD menus 6 Down function button Moves down in the LCD menus 7 Enter function bu
8. S FAR3 FC CH 2 secondary fibre channel at the rear of the disk array system 2 Connectthe optical cable B to the LC Optical SFP transceiver A 10 easyRAID Q16PS F4R3 SAS Disk Array Systems Connecting the GUI management port by a Ethernet cable standard RJ45 to LAN WAN environment and open a web browser with easyRAID Q16PS F4R3 IP address Default is 192 168 0 1 and DHCP exabled for easily monitoring configuring RAID sys tem Don P Secas le iaa OSes Connect a SAS SFF 8088 miniSAS connector external cable to JBOD enclosure 11 suonoeuuo Puen uoneun iuo oiseg c suonoeuuo uen uoneun amp iuo oiseg c easyRAID Q16PS F4R3 SAS Disk Array Systems Connecting and Turning on the Power 1 Plug a power cable A to a power connector at the rear of the unit then plug the second power supply cable into the second power connector B Note Y The system is equipped with auto switching power supplies that can run on 100 to 240 VAC 2 Switch on both power supply switch C 12 easyRAID Q16PS F4R3 SAS Disk Array Systems When the disk array system is completely set up it can be installed in a standard 19 inch rack Follow the instructions in this section to install the disk array system in a rack 1 Clip eight rack nuts supplied with your rack into the rack taking care that they correspond with the mounting points on the rails 2 Extend both of the rails so that they are the right
9. e before using it Protect the disk array system from being bumped or dropped Do not place the disk array system on an unstable cart stand or table It may fall causing serious damage to the product Keep the disk array system away from magnetic forces Do not use the disk array system near water Keep the disk array system away from dust sand or dirt Gaps and openings in the cabinet are provided for venti lation Never block or cover these openings because the disk array system may overheat and become unreli able Don t place the disk array system on a bed sofa rug or other similar surface Do not place the disk array system near or over a radia tor or other heat source Refer to the rating plate for the correct voltage and ensure that the appliance voltage corresponds to the supply voltage easyRAID Q16PS F4R3 SAS Disk Array Systems ee The appliance must be grounded The disk array system is equipped with a 3 wire grounded type of power cord This power cord will only fit into a grounded type of power outlet DH AN If an extension cord or a power center is used with the disk array system make sure that the total current con sumption of all products plugged into the wall outlet does not exceed the ampere rating Do not place the disk array system where the cord will be walked on Never push any kind of object into the disk array system through cabinet gap
10. easyRAID Q16PS F4R3 Hardware User Manual 4G Fibre Channel to SAS Disk Array System Version 1 0 easyRAID Q16PS FAR3 4G Fibre Channel to SAS Disk Array System Hardware User Manual Table of Contents Preface A A A ee tt Chapter 1 System Requirements Operating Environment ssssssssess eee 1 Host Interface 4G Fibre Channel sssssssseem 1 Hard Disk Interface Serial Attached SCSI sss 1 VT100 Terminal Settings ii E 2 iique ua cS 2 Chapter 2 Basic Configuration Unpacking cT 3 Components ansehe As 4 Closed Front Panel aan ei re 4 Open Front Panel miooo d eer ter i E be ER hinkeln 5 DIS TT qe EET 6 easyRAID Q16PS F4R3 Rear View essem 7 Installing DISKS a et Le 8 Making CORTNSCUONS cdta cono EFFERLETEELERERERFIEREINEREFEREFEIFRTESPELHEREREFFERLER RFERERTR 10 Connecting the Host Interface oooooininncinnnnonmirccccccncacnnnaicnarcccnnn aa 10 Connecting the GUI management port ueneeessssnnnnnnnennennnnnnnnnnnnnnennnnn nennen 11 Connecting the JBOD enclosure cecccccccceeeeeeeeeeeseeceeeeeeeedeneeceteeeeneeeeeees 11 Connecting and Turning on the Power ssseseene 12 Mounting ina Rack id det ie e b icon 13 Installing the RailExtenders hama are dt d 14 Chapter 3 Maintenance Replacing aDisk art 15 Replacing a Power Supply cocooccoccccccccccoconononononnnno cnn nono nono nn nnnnnnnn nn nennen 16 Upgrad
11. ing Memory zer a 17 Replacing a FAN module eret oi 18 Appendix Hardware Specifications rossiia a a a a eaa 19 This manual is designed to make the disk array system as easy to use as possible Information contained in this document has been checked for accuracy but no guaran tee is given that the contents are correct Information and specifications are subject to change without notice O Copyright 2007 All rights reserved This disk array system and related documentation are protected by copyright and are distributed under licenses restricting their use copying and distribu tion No part of this documentation may be reproduced in any form by any means with out prior written authorization the company and its licensors if any Caution A This symbol is used to remind users to pay attention to important descriptions regarding usage and maintenance repair or additional important information related to this disk array system Note o This symbol is used to remind users of useful information that can make procedures such as configuration easier to accomplish BuljpueH pue aed suononuisu Ajayes Juenodwj 928J9Jd easyRAID Q16PS F4R3 SAS Disk Array Systems Before starting take a few minutes to read this manual Read all of these instructions and save this manual for later reference Protect the disk array system from extremely high or low temperatures Let the disk array system warm or cool to room temperatur
12. ower Error LED at the front of the drive tray turns red and the audible alert sounds Note o Turn off the audible alert by pressing the Up 4 and Down y function but tons on the front panel twice simultaneously The LCD panel displays the failure with the symbol R or W R indicates a disk fail ure or error and W indicates that there are too many bad sectors on the disk Example Disks 1 to 7 are members of array group 1 Disks 8 to 14 are members of array group 2 11111112222222WR Disk 15 has too many bad sectors Disk 16 has an error or a fault Disks are hot swappable which means that they can be inserted and removed while the disk array system is powered on and operating Follow these instructions to replace a failed disk 1 Unlock the front panel door then pull it open 2 Pull the tray handle away from the disk tray to release it and pull the disk tray out 3 Remove the screws from the failed disk then remove the disk from the disk tray 4 Align the rear of the new disk with the rear of the disk tray 5 Insert the new disk into the disk tray Note of The new disk must have the same or a greater capacity than the faulty disk that was removed If the disk capacity is smaller the audible alert sounds and the auto rebuild operation doesn t start For best performance it is recommended that the new disk be identical to the failed disk 6 Attach the disk to the disk tray with the screws tha
13. s and openings since they may touch dangerous voltage points and cause a risk of fire or electric shock Unplug the power cord from the wall outlet before clean ing Keep the disk array system dry Do not use liquid cleaners aerosol cleaners or a wet cloth Use a damp cloth for cleaning Od 9 FR e oj La Except as specifically explained in this User Manual do not attempt to service the disk array system by yourself Opening or removing the covers may expose you to dangerous voltages 1Q yn Unplug this product from the wall outlet and refer servic ing to qualified service personnel under the following conditions If the disk array system has been exposed to water or any liquid If the disk array system has been dropped or the cabinet damaged Users should not remove the cover Disconnect all power supply cords before servicing BuljpueH pue aed suononusu Ajejes Juenodwj 928J9Jd BuljpueH pue aed suononusu Ajejes Juenodwj 928J9Jd easyRAID Q16PS F4R3 SAS Disk Array Systems Placement Notes The disk array system LCD panel can be damaged by exposure to direct sunlight Limit exposure to subdued or indirect sunlight only The disk array system should be used only in clean environments that are free from airborne contaminants such as dust dirt and smoke Excessive moisture or oil particles in the air can also hinder disk array system performance To red
14. t came with the disk 7 Slide the disk tray back into the empty slot then close the disk tray handle 8 Push the front panel door closed and lock it 15 iddns 18 wog e Buroejdes eoueuejure A easyRAID Q16PS F4R3 SAS Disk Array Systems Replacing a Power Supply The disk array system is equipped with a Power Supply Fail Indicator LED at the front of the unit that turns red when one of the power supplies fails The message Power x fail ure also appears on the LCD panel where x refers to power supply 1 or 2 and an audible alert sounds Note Turn off the audible alert by pressing the Up 4 and Down y function but tons on the front panel twice simultaneously Power supplies are hot swappable which means that they can be inserted and removed while the disk array is powered on and operating Follow these instructions to replace a failed power supply 1 Identify the power supply that has failed 2 Remove the power cable from the power supply connector at the rear of the unit 3 Loosen the power supply retaining screw Bu Power Supply retaining screw 4 Remove the faulty power supply by pulling the power supply handle A and pressing the release catch B at the same time Release catch 5 Insert a new power supply 6 Tighten the power supply retaining screw _ 7 Reconnect the power cable 16 easyRAID Q16PS F4R3 SAS Disk Array Systems Upgrading Memory The disk array system takes a single DDRII
15. tton Selects a menu item or confirms a choice or entry 8 Escape function button Returns to the previous LCD menu without making changes 9 Lock Locks front cover easyRAID Q16PS F4R3 SAS Disk Array Systems 1234 5678 9 10 11 12 13 14 15 16 17 No Name Description 1 16 Disk trays 1 16 Removable hot swap disk trays 17 Front panel door Protects the disks and houses the LCD panel sjuauodulo uomneJun iuo oiseg Z sjusuodwoy uoneinByuoy seg c easyRAID Q16PS F4R3 SAS Disk Array Systems Disk Tray No Name Description Power Error indicator LED Different colors indicate different disk states e Green Disk online Orange Disk fail e Red No disk 2 Access indicator LED This blue LED indicates that the disk is being accessed 3 Tray handle Releases the disk tray easyRAID Q16PS F4R3 SAS Disk Array Systems easyRAID Q16PS FAR3 Rear View
16. uce the possibility of data errors caused by electromagnetic interference locate the disk array system at least five feet away from electrical appliances and equipment that generates magnetic fields Power Supply Safety Notes To avoid electric shocks do not use an extended power cord or an outlet that does not match the disk array system plug or leaves the plug exposed The disk array system has a 3 wire grounded plug The third pin connects to ground do not remove it If the power cord or plug is damaged or worn unplug it immediately and contact a qualified service technician for maintenance To avoid fire or electric shocks do not overload electric power out lets 1 System Requirements Ensure that the following requirements are met before installing the disk array system 15 cm 6 inches of space around the disk array system for proper ventilation ambient temperature of 5 C to 40 C 40 F to 104 F ambient non condensing relative humidity of 1096 to 8596 dust smoke and oil free environment no large magnetic fields such as those generated by a high voltage power cables and motors etc no direct sunlight a flat stable surface capable of supporting the disk array system Host Interface 46 Fibre Channel The easyRAID Q16PS F4R3 has dual 4 Gbit fibre channel interfaces with SFP connec tors for linkage to a fibre channel switch or host computer interface card With the cor rect SFP transceiver
Download Pdf Manuals
Related Search