Z202 - Installation Manual - Vision Tech America, Inc.
Contents
1. INSTALLATION MANUAL CA PASS TOUCH Digital door lock s A PASS TOUCH WIRE INSTALL Caution Main power should be connected at Key box not Fuse box Caution If you can not find the Factory Alarm Rearm output and Factory Alarm Disarm output connect the Black Red Brown and Orange color wire only Factory Alarm rearm disarm function is not available Pin Color Description a esen Powernpt akey Components j a me eme TRA Iom 3M VHB Wwe mM eaa aaa HA We wlH he ag ms Gir y JHA WE 3M VHB Keypad Main unit wire 1 Mounting Procedure 1 Find the plus ground door lock door unlock line to connect 2 Connect to the main unit and check the touch operation status 3 Remove the connector from the main unit 4 Peel off the protective vinyl on the keypad 3M VHB JHA We oa wiHA WE 3M VHB wl 5 A PASS TOUCH placement We recommend placing it center of the Pillar of the front windshield e The direction of 1 6 is downside and 5 O are upside Left side handle e The direction of 5 0 is downside and 1 O are upside Right side handle e Please make sure to affix keypad completely to avoid air bubble forming 7 Align the keypad and main unit precisely LED and numbers should be matched Make sure to align the LED s to the LED holes on the keypad or to align the main unit to the white line on the back of the keypad And connect t2. een 1 2 3 4 5 for the desired number of lock pulses 5 Hold down the SHIFT ENTER button until all LED blink 3 times 1 Press and release the reset button on the back of the main unit 2 Hold down buttons 4 and 5 together with two fingers on the keypad from outside the windshield until LED 1 2 3 light up 3 Let go of the buttons 4 and 5 LED 1 2 3 will stay on 4 For 0 8 seconds press and release button 1 For 3 5 seconds press and release button 2 For 0 3 seconds press and release button 3 5 Hold down the SHIFT ENTER button until all LED blink 3 times Programming of Factory Reset 1 Press and release the reset button on the back of the main unit 2 Hold down buttons 1 and 4 together with two fingers until all LED s light up from outside the windshield This will do Factory Reset USER S MANUAL gC A PASS TOUCH Digital door lock system The system can be locked or unlocked by touching the A PASS TOUCH with a PIN of 4 10 digits A P ASS Touch Enter Shift Key Touch area LED Indicator 1 PIN Registration default PIN CODE 0000 a Press and release the reset button on the back of the main unit b Hold down the buttons 1 and 2 together with two fingers on the keypad from outside the windshield until all LED s blink 3 times c Enter 4 10 digit PIN and touch the ENTER until the LED will indicate the PIN number in ord
3. er and all LED s blink 3 times In order to toggle between 1 5 and 6 0 touch the SHIFT ENTER button 2 System Control 1 Unlock the door a Touch the ENTER button until all LED s light up b Enter 4 10 digit PIN code c Touch the ENTER button until 1 2 3 LEDs light up and select the button 2 for door unlock 2 Lock the door a Touch the ENTER button until all LED s light up b Enter 4 10 digit PIN code c Touch the ENTER button until 1 2 3 LEDs light up and select the button 1 for door lock 3 LED Scan On Off Scan feature only works with the door locked a Touch the ENTER button until all LED s light up b Enter 4 10 digit PIN code c Touch the ENTER button until 1 2 3 LEDs light up and select the button 3 for LED scan On Off By the same process change to off state Cautions e f you make the input mistake 5 times the system will be blocked for 10 minutes Then you can use the system again after 10 minutes e Please keep your PIN CODE safe when you use the A PASS TOUCH e Operating temperature 22 F 176 F
4. he wire 8 Align the white wire of the connector to the arrow mark on main unit Notices 1 If the glass is tinted it is recommended that you cut off the keypad size and attach the main unit on it 2 Unplug the connector in case of poor behavior and re connect it 3 Check sensing 1 Touch the ENTER button until all LED s light up about 2 seconds 2 In order to toggle between 1 5 and 6 0 touch the Enter Shift button speedily about 0 5 second 4 Touch area A PASS Touch Touch the rectangular area between two numbers softl FAQ Q1 There are no responses when touch the keypad 1 Unplug the connector in case of poor behavior re connect it All LED s blink 3 times 2 Check the glass if tinted or not Tinted glass may avoid the normal touch responses 3 Touch the rectangular area between two numbers 4 Check the air bubble between glass and keypad 2 Programming of Lock Pulses default 1 Most of the vehicles is at default state Programming of Pulse Duration default 0 8 sec Press and release the reset button on the back of the main unit Hold down buttons 2 and 3 Hold down buttons 3 and 4 together with two fingers on the keypad together with two fingers on the keypad from outside the windshield until all LED from outside the windshield until all LED light up light up Let go of the buttons The LED 1 2 3 4 5 will stay on EJ Choose betw
Download Pdf Manuals
Related Search