Instruction Manual
Contents
1. DO NOT attempt to unplug wires e ENSURE all wiring for seat is clear of all moving parts of the mechanism before during and after re installation of seat 4 Locate the gas spring and loosen the nut on the gas spring using an 11 16 wrench 5 Remove the opposite end of gas spring by removing the cotter amp clevis pin Proceed to step 6 or 7 depending on the necessary adjustment IMPORTANT e DO NOT allow button on end of cylinder to depress while performing this task 12 Copyright 2014 WINCO MFG LLC GENERAL MAINTENANCE GAS SPRING RELEASE ADJUSTMENT continued Chair will not recline 6 If chair will NOT recline when left or right recline levers are pulled rotate the gas spring clockwise A half 1 2 of a revolution or 180 Chair reclines without the use of recline levers 7 If the chair reclines without the use of recline levers rotate the gas spring counter clockwise B half 1 2 of a revolution or 180 8 After adjustment Replace Clevis Pin and Bow Tie Cotter Pin 9 Pull the recline lever A and push back on the chair back B to check for proper adjustment Repeat above steps as needed until correct release action is achieved Then TIGHTEN HEX NUT that you loosened in step 5 IMPORTANT e sure all bow tie cotter pins are securely inserted in all clevis pins WARNING e Failure to securely insert the bow tie cotter pins into the clevis pin could cause the clev2. Copyright 2014 WINCO MFG LLC RECLINE CHAIR FROM ATTENDANT POSITION Attendant should be positioned on the RIGHT or LEFT side of chair 1 While occupant is seated in the chair use one hand to operate the recline lever located on either side of chair to activate the legrest into its raised position 2 operate the infinite back positioning after occupant s feet have been raised use one hand to operate the recline lever A and the other hand to push on the upholstered back B until desired position or maximum recline has been reached Release recline lever A to maintain position IMPORTANT e Do NOT force the back of chair up or down without fully extend ing either of the two recline levers this can damage the chair RETURN CHAIR UPRIGHT FROM ATTENDANT POSITION Attendant should be positioned on the RIGHT or LEFT side of chair 1 While occupant is reclined in the chair attendant should use one hand to operate the recline lever A located on either side of chair while using the other hand to pull up on back Release the recline lever A once the back has fully returned to the upright position Attendant should use one hand to push down on the legrest A until it locks into its stored position NOTE The recline lever does NOT have to be used to return legrest to its stored position WARNING e Attendant should NOT use foot to return the legrest to it s stored position Damage to mechani
3. LLC warrants steel and aluminum base frames for all products when new for the lifetime of the original purchaser This limited warranty does not apply to paint finish or any components attached to the frame such as upholstery foam casters mechanisms or related parts that are covered under above warranties Winco Mfg LLC shall not be liable for any labor shipping or any other costs incurred as a result of or in conjunction with a warranty claim The purchaser s exclusive remedy under this warranty shall be limited to such repair or replacement of defective components at Winco Mfg LLC sole discretion For warranty service contact the dealer that the product was originally purchased from or Winco Mfg LLC directly EXCLUSIONS There are no other warranties conditions representations or guarantees express or implied made or intended by Winco Mfg LLC and all other warranties conditions representations or guarantees including any warranties conditions representations or guarantees under any Sale of Good Act or Like legislation or statute is hereby expressly excluded Any and all other implied warranties shall not extend beyond the duration of the express warranty Liability for incidental or consequential damages is excluded to the extent permitted by law Some states do not allow the exclusion or limitation so the above limitation or exclusion may not apply to you This warranty gives you specific legal rights In addition you m
4. AUGUSTINE TREATMENT e RECLINER OWNER S OPERATING amp MAINTENANCE MANUAL PATENT PENDING PLEASE DO NOT DISCARD THIS MANUAL KEEP FOR FUTURE REFERENCE AND TRAINING TABLE OF CONTENTS IMPORTANT SAFETY INFORMATION ssscecesessereesscoeseesecnerensenneesnscncoesesncersensceesensennenense 3 4 ASSEMBLY INSTRUCTIONS saminean 5 6 ATTENDANT OPERATING 7 9 OCCUPANT OPERATING 5 10 11 GENERAL 22 12 13 5 dadaan aarian iaidd 14 AUGUSTINE CHAIR OPTIONS 15 CONTACT amp WARRANTY BACK COVER Winco assumes no responsibility for damage or injury caused by the improper assembly installation use or maintenance of this product IMPORTANT PLEASE READ THIS ENTIRE MANUAL BEFORE USING RECLINER DO NOT INSTALL MAINTAIN OR OPERATE THIS EQUIPMENT WITHOUT R
5. EADING AND FOLLOWING THIS MANUAL OTHERWISE INJURY AND OR DAMAGE MAY RESULT THE INFORMATION CONTAINED IN THIS MANUAL IS SUBJECT TO CHANGE WITHOUT NOTICE PHOTOS ARE REPRESENTATIVE OF THE PRODUCT AND MAY VARY SLIGHTLY FROM ACTUAL PRODUCTION MODELS SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE NO PART OF THIS MANUAL MAY BE DUPLICATED IN ANY FORM WITHOUT THE PRIOR WRITTEN CONSENT OF WINCO MFG LLC UNAUTHORIZED DUPLICATION MAY RESULT IN CIVIL PROSECUTION TO THE MAXIMUM EXTENT ALLOWED BY LAW Products with the following markings are intended for commercial use only 100 240 VAC 44W 50 60HZ WARNING Long term continuous Supply 12V exposure to heat may cause burns Operating Conditions Read instructions before using T VRheintand 10 40 C DO NOT use wet DO NOT insert pins into upholstery SYMBOLS FOLLOW INSTRUCTIONS DC VOLTAGE APPLIED PART BRAKE CENTRAL LOCKING PINCH POINT GENERAL WARNING SIGN a gt 2 Copyright 2014 WINCO MFG LLC APORTANT PLEASE READ FOR PRODUCTS WITH POWERED OPTIONS Heat Massage etc IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS Read all instructions before using this product When using an electrical appliance basic precautions should always be followed includ ing the following DANGER To reduce the risk of electric shock always unplug this product from the electrical outlet before cleaning maintenance or servicin
6. T RIGHT or BOTH sides BE oe Front Brake A UNLOCKED LOCKED 15 Copyright 2014 WINCO MFG LLC LIMITED WARRANTY TERMS Winco Mfg LLC warrants this product to be free of manufacturer s defects in material and workmanship provided that the product is used ac cording to normal operating conditions and proper maintenance intended by manufacturer This warranty is available only to the original retail purchaser is non transferable and commences on the date of retail sale proof of purchase required LIMITED ONE YEAR COMPLETE PRODUCT WARRANTY Winco Mfg LLC warrants the complete product for one 1 year At Winco Mfg LLC sole discretion it may repair or replace any components freight free that are found to be defective during the first year Winco Mfg LLC shall not be liable for any labor or any other costs incurred as a result of or in conjunction with a warranty claim LIMITED THREE YEAR WARRANTY Winco Mfg LLC warrants recliner mechanisms electrical components vinyl panels and Vinyl on upholstered parts from cracking or delaminating pressurized gas springs and casters when new for a period of three 3 years At Winco Mfg LLC s sole discretion it may repair or replace components found to be defective Winco Mfg LLC shall not be liable for any labor shipping or any other costs incurred as a result of or in conjunction with a warranty claim LIMITED LIFETIME FRAME WARRANTY Winco Mfg
7. ay also have other rights which vary from state to state GENERAL PROVISIONS No warranty herein contained or set out shall apply when damage or repair is caused by any of the following 1 Damage in transit 2 Accident alteration abuse or misuse of product i e exceeding weight capacities applying inordinate pressure to footrest leg rest use in Mental Health facilities like institutions or any unintended use of the product or use in unintended environments i e outdoor showers MRI rooms etc 3 Fire water damage theft war riot hostility acts of God Examples contained in this list are not to be construed as all inclusive Design appearance parts amp construction are subject to change without notice rail 5516 Southwest Ist Lane Ocala Florida 34474 1 800 237 3377 352 854 2929 Fax 352 854 9544 e mail customerservice wincomfg com www wincomfg com 006340 REV 09 25 14 JWC
8. ce use a DAMP CLOTH ONLY to clean switch wiring or power pack located under seat frame e is no heat or massage or flashing light on the switch check power cord connections to wall outlet AND connection of power cord to power pack unit under chair e If switch displays a flashing light Disconnect from wall check all accessible wire connectors under chair for possible loose connections then re plug into wall and test again e If system still does not work contact Winco customer service 1 800 237 3377 CORD STORAGE Models with Heat HT or Heat amp Massage HM To prevent tripping on cord damage to cord or damage to recliner the power cord should be coiled and stored in the Hook amp Loop fastener provided BEFORE moving chair or whenever heat amp massage is not in use 11 Copyright 2014 WINCO MFG LLC GENERAL MAINTENANCE GAS SPRING RELEASE ADJUSTMENT If recline levers fail to operate properly adjust the gas spring using the instructions below 1 Recline back of chair See pg 8 Recline Chair From Attendant Position 2 Return legrest to stored position 3 Remove the seat A and position as shown B See pg 9 Seat Removal WARNING e Seat is tethered to chair frame Do not forcefully pull on seat Chairs equipped with heat and massage e UNPLUG power cord from power source BEFORE removing seat cleaning cleaning or servicing chair e Chairs equipped with heat and massage
9. d screws Immediately REMOVE FROM SERVICE any recliner with broken recline mechanisms torn upholstery and or other mechanical or visible damage USE ONLY WINCO AUTHORIZED REPLACEMENT PARTS NEVER EXCEED the recommended weight capacity 12 This chair is NOT intended nor suitable for patient transport 4 Copyright 2014 WINCO MFG LLC ASSEMBLY INSTRUCTIONS PREPARATION 1 Carefully examine your product for any damage Inspect all components IF DAMAGE IS EVIDENT REFUSE SHIPMENT amp CONTACT FREIGHT CARRIER OR WINCO IMMEDIATELY 2 Remove all packaging material that was secured for shipping 3 Carefully remove the product from the carton 4 Save all boxes and packaging material until after you have assembled your product and have verified that all com ponents are functioning properly REAR BRAKE ASSEMBLY INSTRUCTIONS This chair is shipped with the central locking casters in the LOCKED position To assemble the REAR central lock lever 1 Loosen thumb screw and slide the lever A onto the HEX por tion of the bar 2 Tighten thumb screw 3 Lift UP on the lever to UNLOCK the central locking casters BACK ASSEMBLY INSTRUCTIONS 1 Lock casters by pushing down the central lock lever located at the rear of chair See Lock Unlock Casters pg 7 IMPORTANT e Keep objects and persons clear of the chair before performing step 2 2 Pull one of the recline levers A located on either sid
10. e of the chair until fully extended to bring the recline mechanism B into its upright position NOTE Legrest is spring loaded and will be rapidly released into the recline position when recline lever is pulled 3 Release the recline lever and push legrest in to its stored position 5 Copyright 2014 WINCO MFG LLC ASSEMBLY INSTRUCTIONS BACK ASSEMBLY INSTRUCTIONS 4 Hold the rear apron up exposing the mounting brackets A Lift the upholstered back by its sides while aligning the mounting brackets with the recline mechanism B WARNING e Keep hands clear of connection points or injury may occur IMPORTANT We recommend two people be used for step 4 e careful not to tear or puncture vinyl 5 Slide the back onto the recline mechanism until the middle hole of the mounting bracket A is aligned with the middle hole of the recline mechanism B 6 Install knobs A tethered to back and tighten to a secure fit 7 Ensure that the rear apron rests OVER the rear brace of chair IMPORTANT e Test to ensure the back has been properly installed by pulling up on the back The back should remain securely in place 6 Copyright 2014 WINCO MFG LLC CASTER OPERATION Lock Unlock This chair features two types of casters rigid and central locking The front two casters are rigid casters They are NOT designed to swivel in order to facilitate stable straight steering The rear two casters are ce
11. ease the recline lever once the back has fully returned to the upright position 2 Press down on the legrest with legs feet until it locks into place NOTE The recline lever does NOT have to be used to return legrest to its stored position 10 Copyright 2014 WINCO MFG LLC OPTIONAL HEAT amp MASSAGE OPERATION Control is located on the inside of right arm of chair Right is determined as if sitting in the chair HEAT ONLY MASSAGE Heating Heating elements are located in the seat amp back of chair Push HEAT button See indicator light on switch 3 Lights High Heat Bright Light 2 Lights Medium Heat Med Light 1 Lights Low Heat Dim Light No Light HEAT OFF Allow 5 8 minutes for back and seat to warm to desired setting Heat will automatically shut off after approximately 60 minutes Timer resets each time switch is pressed Massage option The massage option uses 4 separate motors located in the backrest of the chair Two in the lower backrest and two in the middle upper backrest Push MASSAGE button 1X Lower Back Low Intensity 2X Lower Back High Intensity 3X Upper amp Lower Back Low Intensity 4X Upper amp Lower Back High Intensity 5X Alternating Upper amp Lower Back 6X MASSAGE OFF Massage will automatically shut off after approximately 15 minutes Timer resets each time switch is pressed TROUBLESHOOTING e With system disconnected from power sour
12. g WARNING Unplug this product from the electrical outlet when not in use Supervision should be provided when using this product Use this product only for its intended use as described in this manual Do not use attachments not recommended by the manufacturer Never operate this product if it has a damaged cord or plug if it is not working properly if it has been dropped or damaged or dropped into water contact an authorized Winco service center for instructions DO NOT carry or pull this product by power supply cord or use the cord as a handle Keep the cord away from heated surfaces Do not use outdoors To disconnect turn all controls to the off position then remove plug from outlet Pull plug only to remove cord Clean switch with a damp cloth only Warranty will be VOID if liquid is introduced into switch mechanism Extension cords are not recommended DO NOT roll recliner or other equipment over cord Recliner comes with a grounded three prong plug If the plug does not fit into the outlet contact a certified electri cian to install the proper outlet DO NOT MODIFY THE PLUG IN ANY WAY Keep children away from extended foot support or other similar parts DANGER i Never insert pins or attach other metallic fasteners into onto any part of this chair ii Do not use this product if the covering shows signs of deterioration such as checking blistering or cracking iii KEEP DRY Do not operate in a wet or
13. is pins to fall out and result in injury or damage to the chair GENERAL CARE amp CLEANING e REGULARLY lubricate pivot points on the recline mechanism with a lubricant approved by your facility Periodically position the chair back into full recline position to keep the gas cylinder lubricated e Periodically inspect tightness of all screws bolts and nuts e Winco furnishings are built to provide durable reliable service when properly cared for In general all of our products should be 1 Cleaned 2 Rinsed 3 Allowed to air dry It is important to note that disinfecting a product is not the same as cleaning the product Disinfectants alone will not provide adequate cleaning they do not have grease or oil cutting properties to remove grime or hair and skin oils Over time the appearance and feel and performance of your upholstery may diminish if not cleaned properly CLEANING Remove grime hair and body oils Your furnishings should be cleaned with mild soap amp water solution and a damp cloth on a regular basis especially where skin amp hair make contact with upholstery Avoid harsh detergents or chemicals that could damage the upholstery or finish of your recliner If the furnishing is disinfected with chemicals or bleach it MUST be wiped off using only clean water on a damp cloth and then be allowed to air dry Failure to rinse upholstery with clean water can result in a build up of residues over time that can dry out the uphols
14. moist condition or environment WARNING i Long term continuous exposure to heat may cause burns It is recommended that skin in contact with heated area be checked for redness and blistering during long term usage Do not use on an infant invalid or incapaci tated person Do not use on insensitive skin or on a person with poor blood circulation If you are uncertain if you should use this product please consult your physician about the use of heat and massage Do Not Crush Pinch heating elements or wiring WARNING Connect this product to a properly grounded outlet only 3 Copyright 2014 WINCO MFG LLC PORTANT PLEASE READ BASIC SAFETY PRECAUTIONS READ AND FOLLOW ALL DIRECTIONS NEVER STAND on slide out foot support foot support is not a step INJURY MAY OCCUR DO NOT put hands feet or clothing into any openings when changing positions on recliner Attendant MUST con firm that users arms legs hands and feet are clear while changing recliner positions or SERIOUS INJURY MAY OCCUR Lock casters at all times except when moving chair STAY CLEAR of the recliner mechanisms when operating chair DO NOT use recliner for transporting in or with ANY type of vehicle or trailer Winco recliners have not been tested or approved for use by an occupant in any type of vehicle or trailer NEVER use the chair arms or backrest or tables as a seat SERIOUS INJURY OR DAMAGE MAY OCCUR Periodically check the tightness of all nuts bolts an
15. ntral locking casters They are designed to swivel 360 When central lock is engaged caster wheels will NOT roll and caster will NOT swivel From the REAR of chair 1 From the FRONT of chair OPTIONAL FEATURE 3 TO LOCK REAR CASTERS Press down on central lock lever A Lever will lock into position TO UNLOCK REAR CASTERS Lift up with foot on central lock lever A Lever will return to the unlocked position WARNING e Ensure central locking brake is engaged at all times particularly BEFORE seating an occupant in chair and when occupant is exiting the chair e Never operate brakes without proper footwear Closed toe shoes are recommended for operation of brake mechanism TO LOCK REAR CASTERS Push in on the side of the central lock lever labeled UNLOCKED Lever will lock into position amp LOCKED will be visible 4A TO UNLOCK REAR CASTERS Push in on the side of the central UNLOCKED lock lever labeled LOCKED 4A Lever will lock into position amp UNLOCKED will be visible 3A IMPORTANT e Push UNLOCKED to LOCK e Push LOCKED to UNLOCK e visible label indicates the current state of the chair casters WARNING e Ensure central locking brake is engaged at all times particularly BEFORE seating an occupant in chair and when occupant is exiting the chair e Never operate brakes without proper footwear Closed toe shoes are recommended for operation of brake mechanism
16. sm and upholstery may occur Copyright 2014 WINCO MFG LLC SIDE TABLE OPERATION 1 TO RAISE TABLE Grasp center of table and gently lift into place Side table will lock into place with an audible click once fully extended WARNING e DO NOT lean or sit on side tables e DO NOT use table for support or assistance when exiting or entering the chair e Keep hands and objects clear of the moving parts of the table mechanism IMPORTANT Side tables have been rated for a MAXIMUM weight capacity of 20 lbs 9 0 kg 2 TO STORE Lift up on the lever located under the side table and lower to its stored position WARNING e Keep hands and objects clear of the moving parts of the table mechanism SEAT REMOVAL AND REPLACEMENT TO REMOVE THE SEAT 1 Fully recline the chair back See previous page for instruction 2 Pull up on the front of the seat until it releases A then pull seat out away from the front of the chair B WARNING e Seat is tethered to chair frame Do not forcefully pull on seat Chairs equipped with heat and massage e DO NOT attempt to unplug wires UNPLUG power cord from power source BEFORE seat removal cleaning or servicing of chair e ENSURE all wiring for seat is clear of all moving parts of the mechanism before during and after re installation of seat TO INSTALL THE SEAT 3 With the chair back fully reclined slide the upholstered seat along mechanism until it stops A
17. tery and cause changes to the look and feel of the upholstery and eventually can lead to cracking WARNING e When seat is removed use caution cleaning in and around mechanisms Keep hands clear of pinch points amp metal edges or injury may occur Disconnect power Chairs w HM or HT option when cleaning chair Please refer to the PERMABLOK or other instruction tags that may have come with your furnishings for complete care and cleaning instructions Retain information on tag for future use FOR FURTHER CLEANING INFORMATION on standard Winco vinyls VISIT http spradlingvinyl com asset docs research ApprovedCleaners pdf http spradlingvinyl com asset docs research CompleteCareandCleaningGuides pdf 13 Copyright 2014 WINCO MFG LLC AUGUSTINE RECLINER SPECIFICATIONS Specifications Seat Height Back Height Above Seat 28 5 Seat Width arm to 25 755 Seat 20 75 181165 Overall Height 45 75 Weight 34 5 Overall Length With OPTIONAL Trays Up 45 5 Overall Length Reclined Maximum Weight Capacity 500 Ibs 14 Copyright 2014 WINCO MFG LLC Heat amp Massage IV Pole amp Attachment Side Table aie las Heat amp Massage A AEE IV Pole amp Attachment Available on LEFT RIGHT or BOTH sides m EAEE A Heat ONLY ee FACTORY INSTALLED ONLY Accessory Holder Front Brake Available on LEF
18. then press down on the front of the seat until it locks into position B IMPORTANT Ensure the side aprons of the seat are positioned out side of mechanism and do NOT interfere with seat installation 4 Verify the seat has been correctly installed by carefully pulling up on the front and back of the seat Seat should be secure and not move WARNING e Attendant should NOT attempt to seat an occupant after seat has been re installed without first verifying the seat has been installed correctly or serious injury may occur 9 Copyright 2014 WINCO MFG LLC RECLINE WHILE IN THE SEATED POSITION 1 While seated in the chair pull back on either of the recline levers located on either side of chair to activate the legrest into the recline position 2 To operate the infinite back positioning pull back on the recline lever and adjust the upholstered back angle by pushing back with your body until desired angle has been reached Release recline lever A when you have achieved the desired angle to lock the back into position WARNING e DO NOT push or pull legrest to maneuver chair DO NOT stand or sit the legrest e DO NOT place hands legs or feet under seat mid ottoman or legrest e Stay clear of recline mechanism when operating chair RETURN TO THE SEATED POSITION 1 To return the back to the full upright position pull back on either of the recline levers while sitting upright in the chair Rel
Download Pdf Manuals
Related Search