click it or
Contents
1. The tare and object weight must not be beyond the limit 3 If the weighing results are not exact calibration again Ten Maintenance Scale is not connected with power To plug in the power No light Power switch is off To press turn on key Adapter is broken To change new adapter PCB is broken To change new PCB Be over load To decrease load Upper only load cell wire loose To re connect the wire load cell wire loose S CAL To connect load cell wire No connect load cell wire Big air To shut door or window Working stage is unstable To put scale on stable stage Big change of room temperature To control temperature Load cell is broken To check load cell No clear zero before weight No calibrate or calibration weight is inaccuracy Wrong voltage Big error in four corners of load cell Load cell is broken Value unstable To press lt TARE gt key To re calibrate To use right voltage To check error of four corners To check load cell Value inaccuracy or big error Stay or show To reboot or re plug in power wrong symbols AO ASOCIO OMNGIGE To reboot after 30 minutes Show on the Bad operation environment such left all long or as big air vibration big change in To control working temperature repeated room temperature and so on i No set constant before counting To set a2. 8 8 8 8 Maximum capacity S CAL in turns Under weighing mode it shows 0 0 0 0 00 or 0 000 Three Calibration 1 Single range calibration Press lt CAL gt for 3 seconds gt Show CAL gt g flicker gt Put a standard weight on the pan gt Show CAL gt Show weight value gt Enter into weighing mode After calibration if you found it still shows not exactly please re calibrating 2 Mult range calibration Press lt CAL gt for 3 seconds gt Press CAL again and again it will show different weight value and CAL L you can choose one kind of weight values to calibrate on the basis of single range calibration or you also can choose CAL L to perform the linear calibration When the screen shows no CAL it means you did not put weight on the pan in 10 seconds It will leave calibration mode automatically Four Weighing 1 Read the value on the screen after the black spot what is at the bottom left disappeared That means the value is stable 2 The Max weighing is the showing largest value after turn on add 9d e 10d d is minimum reading If overloading it will show and you must take away the goods at once or the balance load cell especially will be broken Five Tare Press lt TARE gt the balance pan can be tared if the blank spot disappears But if there is the black spot the tare function is no effect Six Backl
3. Contents Operating Manual 1 Environment Conditions OEECEECECCECELLELCLLCLLLCLLLLCCLCELLELELCELCLLCCOCL 2 2 Operation Pr 3 Calibration ILE LILILILULILULUILITULULILILULILULULITULULILILIITITILILILILILEI LA 2 4 Weighing POOP eCPCOCOCCCOCTOTOCOTOTOCCCOC OCC OCT OTe rer errr err rr rer 3 Electronic Balance 5 Tare ssssssssssnnccncnsceeeeeccceeee eee 3 6 Backlight TOPIC PTTi rrr rrrir rrr rir r rrr rrr rrr rrr rrr rr rrr rrr rrr rrr rt rrr rrr 3 7 Zero Tracking amp Auto Tare POEs 8 Other Functions 000000 4 8 1 Units Conversion POPC EC OCCOCCTOCOCCOCTOCCOCOCOCCCCO CCC eer rrr 4 8 2 Counting Se 4 8 3 Percentage ee AA Wa WA WAA WA WAA WA AA SA WA AA AA AA KA AE KA HA KAA 4 ji ji 8 4 Print ss ssssssssmmcmenm emcee 4 Thank You For Choosing Our Electronic Balance 8 5 Speed adjustment of weighing 1 5 8 6 Low voltage indication AAA AAA AAA AAA AAA AAA AAA 5 9 Note m22 6 10 Maintenance sss uuuu222222222222000u200u2020u520u0nuuunnnnnnnnnnn 6 11 Accessories tte eee nnEE EE EEEE REESE EERE 7 One Environment Conditions 1 Place the balance in stably and smooth away vibration sunlight airflow and strong electromagnetic wave 2 Temperature 5 C 35 C Temperature Fluctuation lt 5 C h Humidity 50 85 Two Operation 1 Plug in the electronic balance and warm up 10 minutes better 2 Turn on It displays 8 8
4. e higher count accuracy Put the relevant goods on the balance pan then press lt TARE gt to confirm It will show Setting Counting is done When the counting unit weight lt 2d it will show no Cou In this case you should choose several goods together as a Unit and reset 3 Percentage Press lt MODE gt about 3 scends till Unit flashing Press lt MODE gt to choose PER Then press lt TARE gt to confirm show 100 unit Put the goods on the pan and press lt TARE gt the goods are set as a unit 100 Take away the goods and put on other goods it will display When the set goods weight what is divided by 100 is less than 2d it cannot work and only show no PER It should add to goods weight 4 Print Press lt MODE gt about 3 scends till Unit flashing Press lt MODE gt to choose Prt Then press lt TARE gt to confirm Press lt MODE gt to choose hAnd AUto or Contin And press lt TARE gt to confirm hAnd Means Printer just will print one time AUto Means when the objects placed on the pan is gt 3d and only the value is stable Printer will print automatically Contin Means no matter how heavy the object on the pan and no matter whether the value is stable or not Printer will print continuously RS232 Data Frame Format Symbol Data Unit Last Frame 1 Data Symbol 1 Byte ASCII or 2 Da
5. ight Press lt BL gt to turn on off the backlight Seven Zero Tracking and Auto Tare 1 Turn off the balance one hand press and hold lt CAL gt at the same time another hand turn on the balance again Zero will show then loose the key and press lt TARE gt It will show Zero d Press lt TARE gt can adjust the from 0 to 5 Zero0d means no Zero tracking function sensitivity is the highest Zerood means Zero tracking is the largest Zero5d is factory set 2 Then press lt CAL gt it will show tArE press lt TARE gt tArE d will be shown press lt TARE gt can adjust the from 0 to 9 tArEOd means no Auto Tare tArE9d means Auto Tare Function is the largest tArE9d is factory set 3 Press lt BL gt the setting is done after it shows 0 or 0 0 or 0 00 or 0 000 It is convenient to use because the electronic balance can remember the latest setting when you turn on next time Eight Other Functions 1 Units Conversion Press lt MODE gt about 3 seconds till Unit flashing Then press lt TARE gt to confirm Press lt MODE gt to select units and press lt TARE gt to confirm 2 Counting Press lt MODE gt 3 scends till Unit flashing Press lt MODE gt to choose Count Then press lt TARE gt to confirm show pcs Press lt MODE gt pcs can be changed from 10pcs to 500pcs The larger number th
6. ta Field 7 Bytes ASCII One is Decimal Point which has the same position with Display 3 3 Bytes ASCII Units lt 3 bits Supplementary with Space 4 Last Frame ENTER ASCII ODH OAH Units LB 6C 62 OZ 6F 7A GN 474E KG 6B 67 2B 2D Example 38 25g Stable 10 JO 3 8 J2 5 g 2B 30 30 33 38 2E 32 35 20 67 20 20 OD OA 30 00ct Unstable 10 0 0 JO 3 JO c t 2B 30 30 30 30 33 30 2E 20 63 74 20 OD OA 60 pcs Counting Stable O 0 0 0 JO 0 p lc s 2B 30 30 30 30 30 30 20 70 63 73 OD OA 26 Percentage Stable 10 0 JO JO 2 J6 2B 30 30 30 30 32 36 20 25 20 20 OD OA Serial Port Computer 9 Cores Balance 9 Cores Baud Rate bpc 9600 bps Pin 2 TXD Pin 3 RXD Pin 5 GND Note K Series Balances do not have RS232 Interface 5 Speed adjustment of weighing Press lt TARE gt for 3 seconds it will show SPEED drop the key and enter weighing model Although the speed is slow the accuracy is good The same way if you choose SPEED2 the speed is faster but less accuracy 6 Low voltage indication When the screen shows battery symbol in the upper left side it is time to replace the new battery Nine Note in use 1 Warm up 30 minutes before using and calibration 2
7. verage value constant Show No Cou constant is too big or small To re calibrate No data Distracted by static and crash To reboot or re plug in power No back to zero To check all wires PCB is broken To change PCB No calibration Load cell is broken To check load cell Wires loose To check all wires No Backlight Backlight is broken To change new backlight Eleven Accessories Scale Main Frame FULLER CREE REECEEECM TETRA RE RRR RRA KULEEE tunit Scale Pan WW UA ALANA AE KA SUNA UA EEEH TUTU LUKUKI wa NANI a a oe tunit User s Manual AWAAMBIA ICRC CCT AAMUA EE MUWE tunit AC Adapter E E AAA AAA AAAA AARRE A LI tunit OPT Calibration Weight TGS PMT Aa RRA E A LOR a E E AA tunit Windshield T AN CAN A ANS T E TCR ATCC PROCES PUT AS ELIA tunit
Download Pdf Manuals
Related Search