Home

SYSMAC LINK Support Boards for PCI Bus Installation Guide

image

Contents

1. resistance at the nodes on both ends of the Indicators SYSMAC LINK Network The switch must be Refer to the Operation Manual W390 set to OFF at all other nodes Display the status of the Board and Network 126 Dimensions 107 140 162 Unit mm Parts Names and Functions Section 2 1 2 1 2 Optical Ring Model for H PCF Cable 3G8F7 SLK11 E Card Edge Connector 27 Refer to 2 4 Mounting the Board Connect to the PCI Bus slot of the computer _ Board ID Setting Switch Refer to 2 3 1 Board ID Settings If mounting multiple SYSMAC LINK Support Boards to the computer set the ID number 0 to 3 to identify the Board Backup Power Supply Connector Refer to the Operation Manual W383 Use the enclosed cable connector to connect to the backup power supply sw SGBF7 SLRN Cable Bracket Screw Holes Indicators Communications Connector Use to install the Optical Fiber Refer to the Operation Manual Refer to the Operation Manual Cable Bracket W390 W390 Display the status of the Board and Connect the communications cable Network H PCF cable of the SYSMAC LINK Network Dimensions 126 107 140 163 Unit mm Switch Settings Section 2 3 2 2 Checks before Use Check the following before mounting the Board to the computer Note The PCI Bus
2. The Board mounting procedure depends on the computer Perform the mounting operation correctly according to the user manual for the computer Remove all cables communications cables and power supply cables from the Board Turn OFF the power supply to the computer to which the Board is to be mounted and remove the power supply cable Refer to the user manual for the computer remove the casing and mount or remove the PCI Board Align the position and orientation of the PCI bus connectors on the computer and the Board and press in the connectors as far as it will go Make sure that the Board connector is inserted into the computer connector evenly i e not at an angle When mounting the Board do not apply too much force Pull the Board gently to check that it does not come out too easily Secure the left side of the Board using screws tightened to the correct torque of 0 5 Nem SECTION 3 Software Installation This section describes the procedure for installing the software necessary for using a SYSMAC LINK Support Board 3 1 Software Installation Method 0 0 0 cece cee ene eens 3 2 Installing the SYSMAC LINK PCI Drivers 20 0 eee eee ee eee 3 2 1 Installation Procedure Jarot renonse dee NE eh 3 3 Installing FinsGateway Version 3 PCI SLK 0 0 00 02 cece eee eee 3 3 1 Installation Procedure 0 0 cece n 3 3 2 Checking Completed Installation lesse 3
3. Application Procedure 1 3 Application Procedure To create a user application To use the C Library Development environment C 1 Set the Board ID switch x 2 Mount the Board to the computer and connect the communications cable Y 3 Install the software The switch settings must be made before the power supply to the computer is turned ON To enable identifying the ID number set for the Board attach the enclosed ID label to the Board If using an Optical connection also attach the indicator label to the optical cable bracket Install the drivers and C Library to be able to use the Board To use SYSMAC Compolet 4 Create the user application using the card I F library supplied with the Board 5 Set the data link tables and routing tables using the Support Software ac cording to the devices used Version 2 or ValueAid Pack97 Development environment Visual Basic SYSMAC Compolet Version 2 and ValueAid Pack97 is not included with the Board Refer to the relevant manual for package software use The SYSMAC LINK PCI driver sup plied with FinsGateway can also be used To use PLC Reporter 32 AIMAX FA or other pack age software Package software is not included with the Board Refer to the relevant manual for pack age software use SECTION 2 Settings and Installation This section describes h
4. Driver Files Search Results e The wizard has finished searching for driver files for your hardware device The wizard found a driver for the following device a Network Controller Windows found a driver for this device To install the driver Windows found click Next amp g d wdmiclk pei clkpci inf Cancel Installing the SYSMAC LINK PCI Drivers Section 3 2 Installation has been completed Upgrade Device Driver Wizard Completing the Upgrade Device Driver Wizard p Sysmac Link PCI Windows has finished installing the software for this device To close this wizard click Finish Note It is necessary to log on as a user with administrator privileges to perform the installation Registering a New Device from the Control Panel 1 2 3 1 Select Settings and Control Panel from the Windows Start Menu and then click the Add Remove Hardware Icon Ee a xi Be EE Yee Cue Tek pep EJ o i Erdin ias iR GS Ri Ahihi 321 caira Fana e iig d asma US g inea Adee dfai Ders Control Panel Thi Fresca Tosti iretur pee and broio herder m Ai Fiennes dbardean ao EN T Ty aJ E Vrertalis etnies ind a gagbierocki ha drw t Prie Fahr Optio Porti zama Internat Karriere Controller porn sired Unde co e ahea Supper JA zB b t Fnr Mete nn Phoss wu Aras Done Preys Baral Diageo Hikki man haue Hardr and seth Over and THH Pimek Pnr Drea eran Stal rouble
5. REGARDING THE PRODUCTS UNLESS OMRON S ANALYSIS CONFIRMS THAT THE PRODUCTS WERE PROPERLY HANDLED STORED INSTALLED AND MAINTAINED AND NOT SUBJECT TO CONTAMINATION ABUSE MISUSE OR INAPPROPRIATE MODIFICATION OR REPAIR No 6182 Application Considerations SUITABILITY FOR USE OMRON shall not be responsible for conformity with any standards codes or regulations that apply to the combination of products in the customer s application or use of the products At the customer s request OMRON will provide applicable third party certification documents identifying ratings and limitations of use that apply to the products This information by itself is not sufficient for a complete determination of the suitability of the products in combination with the end product machine system or other application or use The following are some examples of applications for which particular attention must be given This is not intended to be an exhaustive list of all possible uses of the products nor is it intended to imply that the uses listed may be suitable for the products Outdoor use uses involving potential chemical contamination or electrical interference or conditions or uses not described in this manual Nuclear energy control systems combustion systems railroad systems aviation systems medical equipment amusement machines vehicles safety equipment and installations subject to separate industry or government regulation
6. normal communications cannot be performed Do not start the Setup Diag nosis Utility while the system is operating 2 The Setup Diagnosis Utility can be used once FinsGateway has been set up and the Board driver settings have been made correctly 3 6 1 Application 1 2 3 1 Click the Start Button and select Programs Omron SYSMAC LINK and SLKDiagPCI to start the Setup Diagnosis Utility A table of the Support Boards currently installed will be displayed in the main window SikDiagPCI x ID Model Result 0 3G8F 7 SLK 1 2 Select the Board to be diagnosed and click the Test Button to start the data exchange test between the specified Board and the computer 2 Sk DiagPCl When the test has been completed the results will be displayed x fe i Data Exchange Test between PC and board is completed Note While the test is being performed the RUN indicator and ERR indicator on the Board will flash 32 Setup Diagnostic Utility Section 3 6 Error Messages and Remedies Error message Error details and remedy This board has a hardware Board hardware error problem A data checksum error has occurred between the computer and the Board Replace the Board Driver I F error An error has occurred in the interface with the Fins Gateway driver If the FinsGateway service SLKPCI_UNIT is operating stop the service Open the FinsGateway Service manager and check the settings For details r
7. now This message is displayed when the confirmation dialog for stopping FinsGateway ser vices is rejected Setup cannot run with services running After switching applications and closing the FinsGateway Service Manager click Yes To exit Setup click No The FinsGateway Service Manager is running To continue Setup close the Service Man ager from the icon in the task tray To exit Setup click No Could not create temporary files Could not modify the envi ronment variable PATH The environment variable setting failed Add the following to the Autoexec bat file in the root directory of the boot disk SET FinsServer lt full path to the FinsGateway installation folder The following is an example of the default installation to the C drive SET FinsServer C Program Files OMRON FinsServer95 Note The FinsGatewayV3_UsersManual_E PDF User Manual is stored in the online document folder in the application CD ROM 37 Errors after Setup Section 4 2 4 2 Errors after Setup Symptom Message Selecting FinsGateway Help from the Start menu does not start the Help The following table explains the error message that might be displayed after FinsGateway installation The appropriate corrections are also provided Correction To open the FinsGateway Help an appropriate version of Internet Explorer and the HTML Help runtime component are required For details refer to Section 3 Setup Procedure
8. is provided as a guide for the user in determining suitability and does not constitute a warranty It may represent the result of OMRON s test conditions and the users must correlate it to actual application requirements Actual performance is subject to the OMRON Warranty and Limitations of Liability ERRORS AND OMISSIONS The information in this manual has been carefully checked and is believed to be accurate however no responsibility is assumed for clerical typographical or proofreading errors or omissions Notice OMRON products are manufactured for use according to proper procedures by a qualified operator and only for the purposes described in this manual The following conventions are used to indicate and classify precautions in this manual Always heed the information provided with them Failure to heed precautions can result in injury to people or dam age to property N DANGER Indicates an imminently hazardous situation which if not avoided will result in death or serious injury Z N WARNING Indicates a potentially hazardous situation which if not avoided could result in death or serious injury Z N Caution Indicates a potentially hazardous situation which if not avoided may result in minor or moderate injury or property damage OMRON Product References All OMRON products are capitalized in this manual The word Unit is also capitalized when it refers to an OMRON product regardless of whet
9. special functions Microsoft Visual C Ver 6 0 used to control the Board from the user applications Install the C Library if creat ing user applications for the Board The Setup Diagnosis Utility checks if the Board and software have been installed correctly and that data exchange can be performed correctly between the Board and the computer drivers Note 1 To use the C Library FinsGateway SYSMAC LINK PCI Embedded Edi tion must be installed 2 For details of the C Library functions refer to the SYSMAC LINK Support Boards for PCI Bus Operation Manual W390 3 For details on the Setup Diagnosis Utility refer to 3 6 Setup Diagnostic Util ity 3 4 1 Installation Procedure The installation procedure for the C Library and the Setup Diagnosis Utility is de scribed below 1 2 3 1 Close all applications currently open 2 Insert the SYSMAC LINK Support Board Support Software CD ROM in the CD ROM drive 3 Click the Start Button select Run enter D SlkSetup exe and click the OK Button If the CD ROM drive is not drive D enter the correct drive Le SYSMAC LINK Support Software SYSMAC LINK Support Board Q FinsGateway 3 C Library 3 Readme 3 Exit C OMRON Corporation 2000 All Rights Reserved 29 Installing the C Library and Setup Diagnostic Utility Section 3 4 4 Click the C Library Button in the SYSMAC LINK Support Software Setup Window to start the C Library and the Setup Diagnos
10. to 3 5 Uninstalling When installing FinsGateway Version 3 PCI CLK or FinsGateway Version 3 PCI SLK however onto a computer with FinsGateway Version 3 Runtime Edition already installed or when installing FinsGateway Version 3 Runtime Edition onto a computer with FinsGateway Version 3 PCI CLK or FinsGateway Version 3 PCI SLK already installed do not remove the product already installed Click the Next Button and continue installation Setup fails during installation program startup The product installer startup failed Be sure the Setup exe is being executed from the CD xxx file delete failure Check whether the file is read only or being used by another application Then run Setup again A file deletion failed The file may be used by another application program Close all the applications that use FinsGateway and try again The FinsGateway online Help requires Internet Explorer Ver Sion3 02 or higher Currently Internet Explorer is not installed or an older version is installed If the online Help does not dis play properly install Internet Ex plorer Version3 02 or higher Setup will continue To open the FinsGateway Help an appropriate version of Internet Explorer is required For details refer to Setup Procedure in this manual For details refer to Setup Procedure in this manual Internet Explorer can be set up after installing FinsGateway The FinsGateway online Help re
11. used for the specified purpose and under the specified conditions especially in applications that can directly or indirectly affect human life You must consult with your OMRON representative before applying a SYSMAC LINK Support Board for PCI Bus to the above mentioned applications Safety Precautions NWARNING NWARNING NWARNING Never attempt to disassemble any SYSMAC LINK Support Board for PCI Bus while power is being supplied Doing so may result in serious electrical shock or electrocution Never touch any of the terminals while power is being supplied Doing so may result in serious electrical shock or electrocution Provide safety measures in external circuits i e not in the Programmable Controller CPU Unit including associated Units referred to as PC in order to ensure safety in the system if an abnormality occurs due to malfunction of the PC or another external factor affecting the PC operation Not doing so may result in serious accidents e Emergency stop circuits interlock circuits limit circuits and similar safety measures must be provided in external control circuits e The PC will turn OFF all outputs when its self diagnosis function detects any error or when a severe failure alarm FALS instruction is executed As a coun termeasure for such errors external safety measures must be provided to en sure safety in the system Application Precautions 5 Z N Caution N Caution N Caution e
12. 3 3 Setting DrVers s usa Roe RC ad Sho A eee Fe ones slg Roe Ru 3 4 Installing the C Library and Setup Diagnostic Utility 0 0 3 4 1 Installation Procedure 0 0 cece eee n 3 5 Uninstalling 555 tre Cn ex oem odes RR CRGU ER dae oes ais 3 5 1 Uninstallation Procedure 0 0 0 0 eee cette rh 3 6 Setup Diagnostic Utility 2 eee eee 3 621 Applicaton ci sue or Sek shee ed ob ee EARS 18 ARDS See see ed 11 Installing the SYSMAC LINK PCI Drivers Section 3 2 3 1 3 2 3 2 1 Software Installation Method Note 1 2 3 To use the SYSMAC LINK Support Board the following software must be installed e FinsGateway Version 3 PCI SLK e C Library e Setup Diagnostic Utility If not creating user applications using MS C the C Library is not required The Setup Diagnostic Utility is used only when setting up the Support Board The installation procedure is given below 1 Install the PCI SYSMAC LINK Support Board drivers Windows 2000 and Windows 98 only 2 Install the FinsGateway Version 3 PCI SLK and set the drivers 3 Install the C Library and the Setup Diagnostic Utility Only if using the C Li brary or Setup Diagnostic Utility 4 Make detailed Board settings using FinsGateway Refer to 3 3 3 Setting Drivers Installing the SYSMAC LINK PCI Drivers If using Windows 2000 or Windows 98 install the PCI SYSMAC LINK drivers using the operating system s Found New Hardware
13. Drivers 0 0 cece eee eee 3 3 Installing FinsGateway Version 3 PCI SLK 0 0 00 3 4 Installing the C Library and Setup Diagnostic Utility 0 0 0 00 0 3 9 Uninstalling 1 5 peer vv bate Cat hat Sets ENS e oe ead 3 6 Setup Diagnostic Utility si e e a e AA II SECTION 4 Setup Error Messages and Troubleshooting 4 1 Errors during Setup iiis ERG p BREAD oa aE RR M RE RU steeds 4 2 uBrrorscaftet Set p esc se 4 54 25 84 Was etet aie Eae Seem Os ag Le diame Fe SS R vision History 4 294 lw ene ee ieee vii About this Manual This manual describes the installation setup and operation of the 3G8F7 SLK11 E and 3G8F7 SLK21 E SYSMAC LINK Support Boards for PCI Bus and includes the sections described below SYS MAC LINK Support Boards are used to connect IBM PC AT or compatible computers to a SYSMAC LINK Network The following three manuals are directly related to application of the SYSMAC LINK Network Contents Cat No 3G8F7 SLK11 E SLK21 E SYSMAC LINK Support Boards for PCI Bus Installation Guide this manual Installation and setup procedures for SYSMAC LINK Support Boards for PCI bus connections SYSMAC LINK Support Boards are used to connect IBM PC ATs or compatibles to a SYSMAC LINK Network suffixes omitted W389 3G8F7 SLK11 E SLK21 E Operating procedures for SYSMAC LINK Support W390 SYSMAC LINK Support Boards Boards for PCI bus connection
14. SYSMAC 3G8F7 SLK11 E Optical Fiber Cable 3G8F7 SLK21 E Coaxial Cable SYSMAC LINK Support Boards for PCI Bus Installation Guide Produced March 2001 No 6182 OMRON Corporation Read and Understand this Manual Please read and understand this manual before using the product Please consult your OMRON representative if you have any questions or comments Warranty and Limitations of Liability WARRANTY OMRON s exclusive warranty is that the products are free from defects in materials and workmanship for a period of one year or other period if specified from date of sale by OMRON OMRON MAKES NO WARRANTY OR REPRESENTATION EXPRESS OR IMPLIED REGARDING NON INFRINGEMENT MERCHANTABILITY OR FITNESS FOR PARTICULAR PURPOSE OF THE PRODUCTS ANY BUYER OR USER ACKNOWLEDGES THAT THE BUYER OR USER ALONE HAS DETERMINED THAT THE PRODUCTS WILL SUITABLY MEET THE REQUIREMENTS OF THEIR INTENDED USE OMRON DISCLAIMS ALL OTHER WARRANTIES EXPRESS OR IMPLIED LIMITATIONS OF LIABILITY OMRON SHALL NOT BE RESPONSIBLE FOR SPECIAL INDIRECT OR CONSEQUENTIAL DAMAGES LOSS OF PROFITS OR COMMERCIAL LOSS IN ANY WAY CONNECTED WITH THE PRODUCTS WHETHER SUCH CLAIM IS BASED ON CONTRACT WARRANTY NEGLIGENCE OR STRICT LIABILITY In no event shall the responsibility of OMRON for any act exceed the individual price of the product on which liability is asserted INNO EVENT SHALL OMRON BE RESPONSIBLE FOR WARRANTY REPAIR OR OTHER CLAIMS
15. SYSMAC LINK Support Board supports Windows Plug amp Play Check item Check details Unused PCI Bus slots Check that there is an unused PCI Bus slot on the computer to be used IRQ Interrupt Required The Board uses an IRQ The IRQ is allocated duplication automatically on the PCI bus In computers using an ISA bus the IRQ may be duplicated with the ISA bus thus preventing the computer from starting Perform one of the following operations to prevent IRQ duplication with the ISA bus e Display the computer BIOS menu and set Plug amp Play to disabled e Display the computer BIOS menu and set the IRQ used by the ISA bus to Reserved auto al location prohibited using the PCI bus IRQ al location settings Note 1 For display and setting procedures for the computer BIOS menu refer to the computer user manual 2 Check the IRQ used by the ISA bus using the following procedure 1 2 3 1 Start the computer before mounting the Board 2 Click the Start Button select Settings and then Control Panel from the Windows Start Menu 3 Double click the System Icon and click the Device Manager Tab 4 Click the Properties Button for the ISA board using IRQ and then click the Resources Tab to check the IRQ status 2 3 Switch Settings 2 3 1 Board ID Setting A maximum of four Boards can be mounted to one computer The Board ID is used by the computer to identify individual Boards when multiple Boards have been mounte
16. The PC outputs may remain ON or OFF due to deposition or burning of the output relays or destruction of the output transistors As a countermeasure for such problems external safety measures must be provided to ensure safety in the system e When the 24 VDC output service power supply to the PC is overloaded or short circuited the voltage may drop and result in the outputs being turned OFF As a countermeasure for such problems external safety measures must be provided to ensure safety in the system Execute online edit only after confirming that no adverse effects will be caused by extending the cycle time Otherwise the input signals may not be readable Confirm safety at the destination node before transferring a program to another node or changing contents of the I O memory area Doing either of these without confirming safety may result in injury Tighten the connector screws for the backup power supply to the torque speci fied in this manual The loose screws may result in burning or malfunction 4 Operating Environment Precautions N Caution N Caution Z N Caution Do not operate the control system in the following locations e Locations subject to direct sunlight e Locations subject to temperatures or humidity outside the range specified in the specifications e Locations subject to condensation as the result of severe changes in tempera ture e Locations subject to corrosive or flammable gases e Locations s
17. This control requires COMCTL32 DLL version 4 70 or higher The system COMCTL32 DLL needs to be updated Follow the procedure described in Section 3 Setup Procedure Clicking on the Help hyperlinks does not display the target file To open a PDF file Acrobat Reader 4 is required For details refer to Section 3 Setup Pro cedure in this manual Note The FinsGatewayV3_UsersManual_E PDF User Manual is stored in the online 38 document folder in the application CD ROM Revision History A manual revision code appears as a suffix to the catalog number on the front cover of the manual Cat No W389 E1 1 Revision code The following table outlines the changes made to the manual during each revision Page numbers refer to the previous version Revision code Date Revised content March 2001 Original production 39
18. Wizard function If using Windows NT4 0 proceed to 3 3 Installing FinsGateway Version 3 PCI SLK Installation Procedure This section describes an installation example using Windows 2000 If using Windows 98 the operations and windows displayed may be slightly different but installation can be performed using the same procedure System Has Detected the New Drivers 12 1 2 3 1 When the computer is started after the Board has been mounted the Board will be detected as new hardware and the Found New Hardware Wizard will start Click the Next Button Y Network Controller wy Found New Hardware Wizard EC Installing Welcome to the Found New Hardware Wizard This wizard helps you install a device driver for a hardware device To continue click Next Cancel Installing the SYSMAC LINK PCI Drivers Section 3 2 2 If the Install Hardware Device Drivers Window is displayed select the Search for a suitable driver for any device recommended option and click the Next Button Found New Hardware Wizard E Install Hardware Device Drivers 4 device driver is a software program that enables a hardware device to work with an operating system This wizard will complete the installation for this device oy Network Controller device driver is a software program that makes a hardware device work Windows needs driver files for your new device To locate driver files and c
19. ateway SysmacLink Runtime 3 0 FinsGateway SysmacLink PCI Embedded 3 10 ae lt Back Cancel 23 Installing FinsGateway Version 3 PCI SLK Section 3 3 3 3 2 Checking Completed Installation Check that FinsGateway has been installed correctly and that FinsGateway has been added to the Windows Start Menu Programs Documents Settings gt Search Help 3 3 3 Setting Drivers gt Fn Accessories d ia FinsGateway Configuration FS Administrative Tools gt EX FinsGateway Help FR Service Manager Next make the SYSMAC LINK Support Board driver settings The setting de tails are given in the following table Setting item Details Local node address Node address Set the Board node address in decimal The possible setting range is given below 1 to 62 Make sure there are no duplicate node settings on the same SYSMAC LINK network Communications Unit address Unit address Set the Board Unit address in decimal The possible setting range is given below 16 to 31 Make sure there are no duplicate Unit addresses for Boards mounted to the same computer Polling node and polled node settings Set the Board startup mode The Board setting is usually Polling Node Set the mode to Polled Node when replacing the Board 24 Installing FinsGateway Version 3 PCI SLK Section 3 3 1 2 3 1 Click the Start Button and select Programs Fi
20. ateway Version 3 PCI SLK Section 3 3 SLKPCI UNITO Icon in the right Service Settings section and click the Start Button um OMRON FinsGateway Settings inl xl File Network EventMemor View Tool Help Tool Bar FB wD Basic DocoMemo info Service Settings Networks amp z P xd SLKPCI_UNITO CPU_UNIT FgwSocke Networks and Units Drivers Memories Bh EventMemories BW Event Conditions Bi FINS Data Areas E Services CPU UNIT FgwSocketProxy Map gent NameSpaceServer SysmacLink Unit SLKPCI_UNITO 3 E Startup Manual ha e S8 Path p Program Files OMR Map amp gent NameSpa Status Stopped Start Start SCM at log in age FIN Vata Areas E E Services ES CPU UNIT Map amp gent NameSpa FqwSocketProxy Ds MapAgent e SERO 18 NameSpaceServer m aai Ries E SysmacL ink Unit 4S SLKPCI_UNITO Note 1 When the SLKPCI UNIT Service is started the Board will start to participate in the network 2 The Board ID numbers correspond to the service names given in the follow ing table Board ID Service name 0 SLKPCI UNITO SLKPCI_UNIT1 SLKPCI UNIT2 SLKPCI_UNIT3 MN wo 28 Installing the C Library and Setup Diagnostic Utility Section 3 4 3 4 Installing the C Library and Setup Diagnostic Utility The C Library is a library of
21. d Make the settings using a small flat blade screwdriver Settings can be made between 0 and 3 in decimal provided that each ID number is used only once on the same computer Note 1 Make the settings so that each ID number is used only once on the same computer 2 The maximum number of Boards that can be mounted is a total of four for all three models 3G8F7 SLK11 E and 3G8F7 SLK21 E 3 The Board ID number is set to 0 at the factory 4 Do not set the Board ID number between 4 and 9 5 When the Board is mounted to the computer it is difficult to check the Board ID from the outside Write the Board ID setting on the enclosed ID No label Mounting the Board Section 2 4 and attach the label in the designated position on the Board Refer to the following diagram Attach the label within the dotted lines 2 4 Mounting the Board After the settings have been completed mount the Board to the PCI bus slot on the computer An example of the mounting procedure is given below Note 1 2 3 1 When mounting or dismounting the Board always turn OFF the power sup ply to the computer and all peripheral devices When mounting the Board beware of static electricity There is a risk that the Board or the computer will be damaged When mounting or dismounting the Board be careful not to damage the memory or other parts in the computer Do not directly touch the back of the Board or the parts
22. efer to 3 3 3 Setting Drivers The main window board table is FinsGateway drivers cannot detect the Board not displayed Open the FinsGateway Service manager and check the settings For details refer to 3 3 3 Setting Drivers 33 SECTION 4 Setup Error Messages and Troubleshooting This section describes the error messages that may occur during setup their causes and their remedies 4 1 BErrors d nung Setup ev eRRIDeDbeeeeeAU PEL euet UU Bae e Sane ees 4 2 Errors after Setup 5 ues Ree M epe RE MERE RE RE ek ee eh RE pU E 35 Errors during Setup Section 4 1 4 1 Errors during Setup The following table explains error messages that might be displayed during FinsGateway installation or removal The appropriate corrections are also pro vided Correction Symptom Message Nothing happens when insert ing the FinsGateway CD Use the following procedure to execute the SlkSetup exe in the root directory of the CD From the Windows Start menu select the Execute File option and enter the following CD ROM drive SlkSetup exe Alternatively execute SIk Setup exe from Explorer Setup found the following prod ucts on the system Remove the old product versions then install FinsGateway Version3 Refer to the manual for details about removing the previous product versions Follow the procedure described in this manual to remove the previous version of FinsGate way For details refer
23. ended Audience This manual is intended for the following personnel who must also have knowl edge of electrical systems an electrical engineer or the equivalent e Personnel in charge of installing FA systems e Personnel in charge of designing FA systems e Personnel in charge of managing FA systems and facilities General Precautions Z N WARNING The user must operate the product according to the performance specifications described in the operation manuals Before using the product under conditions which are not described in the manual or applying the product to nuclear control systems railroad systems aviation systems vehicles combustion systems medical equipment amusement ma chines safety equipment and other systems machines and equipment that may have a serious influence on lives and property if used improperly consult your OMRON representative Make sure that the ratings and performance characteristics of the product are sufficient for the systems machines and equipment and be sure to provide the systems machines and equipment with double safety mechanisms This manual provides information for programming and operating the SYSMAC LINK Support Board for PCI Bus and related devices Be sure to read this manu al before attempting to use the software and keep this manual close at hand for reference during operation It is extremely important that a SYSMAC LINK Support Board for PCI Bus and all related devices be
24. esult in severe civil and criminal penalties and will be prosecuted to the maximum extent possible under law Cancel 22 Installing FinsGateway Version 3 PCI SLK Section 3 3 6 Follow the setup program instructions When setup has been completed re start the computer Setup Complete Setup has finished copying files to your computer Before you can use the program you must restart Windows or your computer Yes want to restart my computer now C No will restart my computer later Remove all media from drives then click Finish to complete setup Note If the setup program discovers a FinsGateway product already installed the messages shown below will be displayed When installing FinsGateway Version 3 PCI CLK or FinsGateway Version 3 PCI SLK onto a computer with Fins Gateway Version 3 Runtime Edition already installed or when installing Fins Gateway Version 3 Runtime Edition onto a computer with FinsGateway Version 3 PCI CLK or FinsGateway Version 3 PCI SLK already installed do not remove the product already installed Click the Next Button and continue instal lation FinsGateway products on this computer X Before installing new versions of the items in the following list uninstall the current versions Products older than version 1 14 may still be displayed after being uninstalled If all old versions have been removed click Next Current Settings FinsG
25. f the computer before attempting any of the follow ing Performing any of the following with the power supply turned on may lead to electrical shock e Installing or removing the Support Board e Assembling the Units e Setting DIP switches or short circuiting pins e Connecting or disconnecting any cables or connectors Failure to abide by the following precautions could lead to faulty operation of the computer or the system or could damage the SYSMAC LINK Support Board for PCI Bus or related devices Always heed these precautions e Fail safe measures must be taken by the customer to ensure safety in the event of incorrect missing or abnormal signals caused by broken signal lines momentary power interruptions or other causes e Always use the power supply voltage specified in the operation manuals An incorrect voltage may result in malfunction or burning e Take appropriate measures to ensure that the specified power with the rated voltage and frequency is supplied Be particularly careful in places where the power supply is unstable An incorrect power supply may result in malfunction e Install external breakers and take other safety measures against short circuit ing in external wiring Insufficient safety measures against short circuiting may result in burning e Disconnect the functional ground terminal when performing withstand voltage tests Not disconnecting the functional ground terminal may result in burning e Do not at
26. her or not it appears in the proper name of the product The abbreviation Ch which appears in some displays and on some OMRON products often means word and is abbreviated Wd in documentation in this sense The abbreviation PC means Programmable Controller and is not used as an abbreviation for any thing else Visual Aids The following headings appear in the left column of the manual to help you locate different types of information Note Indicates information of particular interest for efficient and convenient operation of the product 1 2 3 1 Indicates lists of one sort or another such as procedures checklists etc OMRON 2001 All rights reserved No part of this publication may be reproduced stored in a retrieval system or transmitted in any form or by any means mechanical electronic photocopying recording or otherwise without the prior written permis sion of OMRON No patent liability is assumed with respect to the use of the information contained herein Moreover because OMRON is constantly striving to improve its high quality products the information contained in this manual is subject to change without notice Every precaution has been taken in the preparation of this manual Nevertheless OMRON assumes no responsibility for errors or omissions Neither is any liability assumed for damages resulting from the use of the informa tion contained in this publication Intel and Celero
27. ind New Hardware Windows can also detect hardware that is not Plug and Play compatible When Windows detects new hardware it checks the current settings for the device and installs the correct driver Do you want Windows to search for your new hardware C Yes search for new hardware lt Back Cancel 5 Select the Other Device option and click the Next Button Add Remove Hardware Wizard Hardware Type What type of hardware do you want to install Select the type of hardware you want to install Hardware types x Multifunction adapters SX Multi port serial adapters gt MwaveDSP EF Network adapters i9 NT Apm Legacy Support ij PCMCIA adapters 2 Ports COM amp LPT SG Printars xl lt Back Cancel 17 Installing the SYSMAC LINK PCI Drivers Section 3 2 6 Click the Have Disk Button Add Remove Hardware Wizard Select a Device Driver Which driver do you want to install for this device Select the manufacturer and model of your hardware device and then click Next If you have a disk that contains the driver you want to install click Have Disk Manufacturers Models LISB Audio Device Generic USB Audio Standard IDE ATAZATAPI cor Standard Infrared Port Standard Modem Types Standard port types id ee ee eee ee Petrie 4 b Have Disk pm 7 Insert the applications CD ROM first specify the CD ROM dri
28. ll applications that are currently running 2 Insert the SYSMAC LINK Support Board Support Software CD ROM in the CD ROM drive 3 Click the Start Button select Run enter D SlkSetup exe and click the OK Button If the CD ROM drive is not drive D enter the correct drive 3 SYSMAC LINK Support Software Setup 15 xl SYSMAC LINK Support Board B FinsGateway 3 C Library 3 Readme 3 Exit C OMRON Corporation 2000 All Rights Reserved 21 Installing FinsGateway Version 3 PCI SLK Section 3 3 4 First install FinsGateway as follows Click the FinsGateway Button in the SYSMAC LINK Support Board Software Setup Window to start the Fins Gateway installation 3 SYSMAC LINK Support Software Setup 0 xl SYSMAC LINK Support Board Q FinsGateway 3 C Library 3 Readme 3 Exit C OMRON Corporation 2000 All Rights Reserved 5 Click the FinsGateway Button The following window will be displayed Welcome x Welcome to the FinsGateway Setup program This program will install FinsGateway on your computer It is strongly recommended that you exit all Windows programs before running this Setup program Click Cancel to quit Setup and then close any programs you have running Click Next to continue with the Setup program WARNING This program is protected by copyright law and international treaties Unauthorized reproduction or distribution of this program or any portion of it may r
29. n The ex ample window shows the Board ID has been set to 0 If multiple Boards are mounted all the mounted boards will be displayed in the dialog box Select the ID for the Board to be set 4 The SYSMAC LINK PCI Properties Dialog Box will be displayed Click the Driver Tab and make the driver settings SysmacLink PCI Properties x About Network Driver Product name FinsG ateway SysmacLink PCI Embedded Edition Version 3 10 Vendor OMRON Note Licensed TRUE Install Date 2001 402 03 08 07 Time Limit NONE Cancel Apply 26 Installing FinsGateway Version 3 PCI SLK Section 3 3 5 Click the Network Tab and make the settings by entering the Board node address in the Local node number Field and the communications Unit ad dress in the Communications unit number Field SysmacLink PCI Properties x About Network Driver Network number o Local node number E Communication unit number 31 User defined 6 Click the Driver Tab and set the Polling Node Polled Node for the Board When all the settings have been made click the OK Button SysmacLink PCI Properties X About Network Driver BoardD 0 v Run SYSMAC LINK PCI support board as the polling node Cancel Apply 7 Click the Basic Tab and the Services Icon in the main FinsGateway Set tings Window to add SLKPCI UNITO to the service settings Next click the 27 Installing FinsG
30. n are registered trademarks of Intel Corporation Microsoft Windows Windows NT Visual C Visual Basic and Visual Studio are registered trademarks of Microsoft Corporation IBM and PC AT are trademarks of International Business Machines Corporation All other product names or company names that appear in this manual are trademarks or registered trademarks of each respective company TABLE OF CONTENTS PRECAUTIONS taco ease tease sees RP CR od I Intended Audience rr S RR I Sha EE ee Pha aes UU ER eh eee 2 General Precautions Br toh D Gani aii ese ale eh a eae RA 3 Safety Precautions os fae chia hab de RC AS IRR RUM REO aR 4 Operating Environment Precautions 0 0 cece 3 Application Precautions eqs eh ee ativan Ageia WEL ee Ree REUS SECTION 1 Outline zur EEQERAV E OR EUAURAU E HERAUS E 1 1 Product Configuration 0 an aa eI E 1 2 Operating Environment 0 0 eee n 1 3 Application Procedure cci Rev RE Se EE EE Se es SECTION 2 Settings and Installation 2 1 Parts Names and Functions 0 0 ccc cece nent een eee ene 2 2 Checks before Use niceties cu i C E ER ES ok 2 3 Switch Settings i cecnesetteenELpenreebwREHDPUR PR LAS Eee e E EEP tobe 2 4 Mounting the Board 0 0 cc cee eee mh SECTION 3 Software Installation een 3 1 Software Installation Method 0 0 0 ee cc e 3 2 Installing the SYSMAC LINK PCD
31. nsGateway and FinsGate way Configuration Programs gt FS Accessories gt ia FinsGateway Configuration Documents gt Ej Administrative Tools 59 FinsGateway Help Settings Search Help Run Shut Down boni Service Manager 2 Click the Basic Tab in the FinsGateway Settings Window and click the Driv ers Icon Next click the SLK PCI Icon in the Driver Settings Section and click the Properties Button EM OMRON FinsGateway Settings ial xl File Network EventMemoy View Tool Help Tool Bar ES Es Basic DocoMemo Info Networks Sr Networks and Units Drivers Memories BR EventMemories Rp Event Conditions Si FINS Data Areas 5 i Services CPU UNIT FgwSocketProxy Map gent 463 NameSpaceServer SysmacLink Unit SLKPCI UNITO Driver Settings SysmacLink HESE 340AA Properties 25 Installing FinsGateway Version 3 PCI SLK Section 3 3 3 The mounted Boards will be displayed in the SYSMAC LINK PCI Lists Dia log Box Select the Board to be changed and click the Change Button SysmacLink PCI Lists i Z3 X Setting Only SYSMAC LINK PCI support board BoardlD Status Add Delete Change E BS Em Refresh installed board Refresh If the Board is not displayed in the dialog box click the Refresh Butto
32. omplete the installation click Next What do you want the wizard to do Search for a suitable driver for my device recommendedj Display a list of the known drivers for this device so that can choose a specific driver lt Back Cancel 3 Insert the applications CD ROM first select the CD ROM Drives option in the Locate Driver Files Window and click the Next Button Found New Hardware Wizard 1 E Locate Driver Files 3 Where do you want Windows to search for driver files Search for driver files for the following hardware device oy Network Controller The wizard searches for suitable drivers in its driver database on your computer and in any of the following optional search locations that you specify To start the search click Next If you are searching on a floppy disk or CD ROM drive insert the floppy disk or CD before clicking Next Optional search locations M CD ROM drives Specify a location _ Microsoft Windows Update lt Back Cancel 13 14 Installing the SYSMAC LINK PCI Drivers Section 3 2 In Windows 98 select the Specify a location option select the CD ROM drive directory as shown below and click the OK Button Install From Disk xj Insert the manufacturer s installation disk into the drive selected and then click OK Cancel d Copy manufacturer s files from D wDMSPCI SLK 4 Click the Next Button Found New Hardware Wizard E ee
33. ore touching the Unit be sure to first touch a grounded metallic object in order to discharge any static built up Not doing so may result in malfunction or damage e Do not touch the Board surfaces or parts e Install the Board according to instructions in the operation manuals Improper installation may cause faulty operation e When using the Optical Ring SYSMAC LINK Support Board for public utilities systems such as electricity gas or water supply use the Optical Ring mode and provide appropriate fail safe measures XV SECTION 1 Outline This section describes the configuration of the SYSMAC LINK network system and the product configuration and operating environment of the SYSMAC LINK Support Boards FI Product Configuration seg UU SHUR OA ede REESE ek se 1 2 Operating Environment cssc sertes ni e eepe e ee 1 3 Application Procedure scissors essri oie sai ea DUE ed RR e UR etn Operating Environment Section 1 2 1 1 Product Configuration The following table lists the product configuration for SYSMAC LINK Support Boards for PCI Bus connections System Model number Details and additional products Coaxial System 3G8F7 SLK21 E e SYSMAC LINK Support Board x1 e CD ROM x1 e Operation Manual x1 e F Adapter x1 e Insulation cover x 1 e Coaxial Cable Bracket x1 e Board ID switch No indicator label x 1 e User registration card software user agreement x 1 Optical System 3G8F7 SLK11 E e SYSMAC LINK Support Board
34. ow to make settings for the SYSMAC LINK Support Boards and how to mount a Support Board to a computer This section also describes the function of the parts of the SYSMAC LINK Support Boards 2 1 Parts Names and Functions 0 cece cece e eee he 2 1 1 Coaxial Model 3G8F7 SLK2I E 0 0 eee eee 2 1 2 Optical Ring Model for H PCF Cable 3G8F7 SLKII E 0 2 2 Checks betore Use i ae Eu LEVER BAe SONG DEAD p Oh NRE 2 37 Switch Settings 4 45 tbat os ee eee ec estive ob et 2 3 1 Board ID Setting cce otis CRAM Sas URE RMU Bee OSES EOE 2 4 Mounting the Board 0 0 eect E mmn Parts Names and Functions Section 2 1 2 1 Parts Names and Functions The following section shows the external appearance of the SYSMAC LINK Support Boards for PCI Bus connections hereinafter called Boards and pro vides the names of parts functions and dimensions of the Board 2 1 1 Coaxial Model 3G8F7 SLK21 E Card Edge Connector Refer to 2 4 Mounting the Board Connect to the PCI Bus slot of the computer 7Board ID Switch Refer to 2 3 1 Board ID Settings If mounting multiple SYSMAC LINK Support Boards to the computer set the ID number 0 to 3 to identify the Board Coaxial Connector Refer to the Operation Manual W390 Connect the coaxial cable of the SYSMAC LINK Network using the po connector attached to the Board This is a slide switch Turn ON the terminating
35. quires the HTML Help runtime component version 1 31 or higher Currently the HTML Help run time component is not installed or an older version is installed If the online Help does not dis play properly install the HTML Help runtime component Setup will continue To open the FinsGateway Help an appropriate version of the HTML Help runtime compo nent is required For details refer to Setup Procedure in this manual The HTML Help runtime component can be installed after installing FinsGateway No products are selected to install Exit Setup To continue Setup click the No Button and select at least one product to install To exit Setup click the Yes Button 36 Errors during Setup Symptom Message Section 4 1 Correction Setup found FinsGateway Ver sion 1 Previous versions of FinsGateway cannot be on the same system Before installing FinsGateway Version3 remove FinsGateway Version 1 Clicking Yes will delete the ap propriate version 1 files and continue the FinsGateway Ver sions installation Clicking No will exit Setup FinsGateway Version 1 or another previous version cannot be installed and run on the same system Remove Version 1 first then install the new FinsGateway version Insufficient hard disk space available to install Install to a different drive or open some of the space on the same drive Then start Setup again Cannot continue Setup Exiting
36. re for this device For the hardware to work you will have to restart the computer To view or change the resources for this Resources device click Resources To close this wizard click Finish Note Itis necessary to log on as a user with Administrator privileges to perform the installation 20 Installing FinsGateway Version 3 PCI SLK Section 3 3 3 3 Installing FinsGateway Version 3 PCI SLK To use the Support Board FinsGateway must be installed Note 1 The FinsGateway Version 3 PCI SLK supplied with the Board is FinsGate way Version 3 If an earlier version of FinsGateway is already installed uninstall the earlier version first and then install FinsGateway Version 3 PCI SLK 2 For the procedure to uninstall earlier versions of FinsGateway and unins tallation precautions refer to the FinsGateway User Manual or the Fins Gateway Version 3 Installation Application Precautions FinsGateway Version 3 Caution 1 PDF in the Root Folder on the Applications CD ROM 3 FinsGateway Version 3 PCI SLK and FinsGateway Version 2 cannot both be installed on the same computer 4 The Board SYSMAC LINK PCI drivers cannot be used with FinsGateway Version 2 or earlier 5 The FinsGateway User Manual OnlineDocument English FinsGate way V3 UserManual E PDF is supplied on the applications CD ROM For detailed setup information refer to the online manual 3 3 1 Installation Procedure 1 2 3 1 Close a
37. s Systems machines and equipment that could present a risk to life or property Please know and observe all prohibitions of use applicable to the products NEVER USE THE PRODUCTS FOR AN APPLICATION INVOLVING SERIOUS RISK TO LIFE OR PROPERTY WITHOUT ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS AND THAT THE OMRON PRODUCTS ARE PROPERLY RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE OVERALL EQUIPMENT OR SYSTEM PROGRAMMABLE PRODUCTS OMRON shall not be responsible for the user s programming of a programmable product or any consequence thereof No 6182 Disclaimers CHANGE IN SPECIFICATIONS Product specifications and accessories may be changed at any time based on improvements and other reasons It is our practice to change model numbers when published ratings or features are changed or when significant construction changes are made However some specifications of the products may be changed without any notice When in doubt special model numbers may be assigned to fix or establish key specifications for your application on your request Please consult with your OMRON representative at any time to confirm actual specifications of purchased products DIMENSIONS AND WEIGHTS Dimensions and weights are nominal and are not to be used for manufacturing purposes even when tolerances are shown PERFORMANCE DATA Performance data given in this manual
38. s SYSMAC LINK for PCI Bus Support Boards are used to connect IBM PC ATs or Operation Manual compatibles to a SYSMAC LINK Network 3G8F5 SLK21 E Installation setup and operating procedures for W220 SYSMAC LINK Support Boards SYSMAC LINK Support Boards for ISA bus for ISA Bus Operation Manual connections SYSMAC LINK Support Boards are used to connect IBM PC ATs or compatibles to a SYSMAC LINK Network CV500 SLK11 21 Installation setup and operating procedures for the W212 SYSMAC LINK Units Operation SYSMAC LINK Units are used to connect CV series Manual PCs to a SYSMAC LINK Network CS1W SLK11 21 Installation setup and operating procedures for the W367 SYSMAC LINK Units Operation Manual SYSMAC LINK Units SYSMAC LINK Units are used to connect CS1 series PCs to a SYSMAC LINK Network Depending on the system you may also need the SYSMAC or CV Support Software or a Programming Console Refer to the body of this manual for details Please read this manual and related manuals care fully and be sure you understand the information provided before attempting to install and operate a SYS MAC LINK Support Board Section 1 describes the configuration of the SYSMAC LINK network system and the product configura tion and operating environment of the SYSMAC LINK Support Boards Section 2 describes how to make settings for the SYSMAC LINK Support Boards and how to mount a Support Board to a personal computer This section also describe
39. s hr syro ab riesen irm 15 Installing the SYSMAC LINK PCI Drivers Section 3 2 2 Select the Add Troubleshoot a device option and click the Next Button Add Remove Hardware Wizard Choose a Hardware Task Which hardware task do you want to perform Select the hardware task you want to perform and then click Next iChoose this option if you are adding a new device to your computer or are having problems getting a device working i C Uninstall Unplug a device Choose this option to uninstall a device or to prepare the computer to unplug a device Back Cancel 3 Select the Add a new device option and click the Next Button Add Remove Hardware Wizard Choose a Hardware Device Which hardware device do you want to troubleshoot The following hardware is already installed on your computer If you are having problems with one of these devices select the device and then click Next If you are attempting to add a device and it is not shown below select Add a new device and then click Next Devices Monitor amp Floppy disk drive NEC CD ROM DRIVE 28B C3FUJITSU M1623TAU DE Crystal WDM Audio Codec Gl Disabled Device a 16 lt Back Cancel Installing the SYSMAC LINK PCI Drivers Section 3 2 4 Select the No I want to select the hardware from a list option and click the Next Button Add Remove Hardware Wizard F
40. s the function of the parts of the SYS MAC LINK Support Boards Section 3 describes the procedure for installing the software necessary for using a SYSMAC LINK Sup port Board Section 4 describes the error messages that may occur during setup their causes and their remedies NNARNING Failure to read and understand the information provided in this manual may result in personal injury or death damage to the product or product failure Please read each section in its entirety and be sure you understand the information provided in the section and related sections before attempting any of the procedures or operations given ix PRECAUTIONS This section provides general precautions for using the SYSMAC LINK Support Board for PCI Bus and related devices The information contained in this section is important for the safe and reliable application of the SYSMAC LINK Support Board for PCI Bus You must read this section and understand the information contained before attempting to set up or operate a SYSMAC LINK Support Board for PCI Bus 1 Intended Audience 2 354065 24 6 6 8 SOs we St a te Ses CEES Ne Oe Es 2General Precautions cde aici seb wa pias oo bea WL ean ea e eee ia Ae Ak 3 Safety Precautions xa st egaied ies nee Sh ale bese RE UPUPESE E bQeb RS PERDRE eds 4 Operating Environment Precautions 0 0 0 cee Ie 5 Application Precautions 0 0 ec eee cent e xi Safety Precautions 1 2 3 xii Int
41. tempt to take the Boards apart to repair the Boards or to modify the Boards in any way e Be sure that all the mounting screws terminal screws and cable connector screws are tightened to the torque specified in this manual Incorrect tighten ing torque may result in malfunction e Use crimp terminals for wiring Do not connect bare stranded wires directly to terminals Connection of bare stranded wires may result in burning e Double check all the wiring before turning ON the power supply Incorrect wir ing may result in burning e Wire correctly e Double check all the connectors before mounting the Board e Be sure that the communications cable connectors and other items with lock ing devices are properly locked into place Improper locking may result in mal function e Use a special packing box when transporting the Board Handle the product carefully so that no excessive vibration or impact is applied to the product dur ing transportation e Check the user program for proper execution before actually running it on the Unit Not checking the program may result in an unexpected operation e Observe the following precautions when wiring the communications cable or backup power supply cables e Separate the cables from power lines or high tension lines e Do not bend the cables e Do not pull on the cables e Do not place heavy objects on top of the cables Application Precautions 5 e Route cables inside conduits e Bef
42. tic Utility installation e SYSMAC LINK Support Software IOl x SYSMAC LINK Support Board Q FinsGateway Q C Library 3 Readme Exit C OMRON Corporation 2000 All Rights Reserved 5 Click the C Library Button The following window will be displayed i C Language Library InstallShield Wizard Welcome to InstallShield wizard for C Language Library InstallShield R wizard installs C Language Library in the computer of the use Click and continue Next Warnung This program is protected by the copyright law and the international treaty i Cancel 30 Uninstalling Section 3 5 6 Follow the setup program instructions If setup has been completed normal ly the following window will be displayed ji C Language Library InstallShield Wizard E xj InstallShield wizard was completed InstallShield wizard installed C Language Library normally Click on Finish and finish wizard The C Library folder configuration is described below SYSMAC LINK Lib C Library files and header files SLK_LIB LIB and SLK_LIB H Setup Diagnostic Utility SIkDiagPCI exe SYSMAC LINK Sample Sample programs used by the C Library Visual C MFC application project files SYSMAC LINK Help C library help file HTML Note The C library DLL SLK LIB DLL file is copied to the Windows system directory 3 5 Uninstalling If the Board software FinsGateway C Library and the Se
43. tup Diagnostic Utility are no longer required because the Board has been removed from the comput er the relevant program files can be deleted using the following procedure Only installed files will be deleted Files created later will not be deleted 3 5 1 Uninstallation Procedure This section describes uninstalling FinsGateway as an example of uninstalla tion If using Windows 98 or Windows NT4 0 the windows item names and op erations displayed may differ slightly so be careful 1 2 3 1 Close all programs and services using FinsGateway 2 Right click the Service Manager Icon in the Task Tray and select Stop all services from the popup menu 3 Double click the Add Remove Programs Icon in the Control Panel Win dow 4 Select the programs to be uninstalled from the table displayed 5 Click the Change Remove Button to start the uninstallation Follow the pro gram instructions to uninstall the software Note After uninstalling FinsGateway restart the system FinsGateway will no longer operate normally 31 Setup Diagnostic Utility Section 3 6 3 6 Setup Diagnostic Utility The Setup Diagnosis Utility checks if the Board and software have been installed correctly and that data exchange can be performed correctly between the Board and the computer drivers Note 1 The Setup Diagnosis Utility operates in a special mode to perform diagnosis of the SYSMAC LINK Support Board so while diagnosis is being performed
44. ubject to dust especially iron dust or salts e Locations subject to exposure to water oil or chemicals e Locations subject to shock or vibration Take appropriate and sufficient countermeasures when installing systems in the following locations e Locations subject to static electricity or other forms of noise e Locations subject to strong electromagnetic fields e Locations subject to possible exposure to radioactivity e Locations close to power supplies The operating environment of the SYSMAC LINK Support Board for PCI Bus or the computer can have a large effect on the longevity and reliability of the sys tem Improper operating environments can lead to malfunction failure and oth er unforeseeable problems with the SYSMAC LINK Support Board for PCI Bus or the computer Be sure that the operating environment is within the specified conditions at installation and remains within the specified conditions during the life of the system 5 Application Precautions Observe the following precautions when using the SYSMAC LINK Support Board for PCI Bus or the computer into which it is installed N WARNING Failure to abide by the following precautions could lead to serious or possibly fatal injury Always heed these precautions xiii Application Precautions 5 Z N Caution xiv e Always ground the system to 100 Q or less when installing the system to pro tect against electrical shock e Always turn off the power o
45. ve and click the OK Button 8 Click the Browse Button and select the DZ WDM PCI SLK Folder on the applications CD Install From Disk x Insert the manufacturer s installation disk into the drive En selected and then click OK Cancel Copy manufacturer s files from Browse 18 Installing the SYSMAC LINK PCI Drivers Section 3 2 9 Select the SYSMAC LINK PCI option from the Models List and click the Next Button Add Remove Hardware Wizard Select a Device Driver Pea as Which driver do you want to install for this device sed Select the manufacturer and model of your hardware device and then click Next If you have a disk that contains the driver vou want to install click Have Disk Models Sysmac Link PCI lt Back Next gt Cancel 10 Click the Next Button Add Remove Hardware Wizard Start Hardware Installation Pea Bast Windows is ready to install drivers for your new hardware acp SS 2 Sysmac Link PCI Windows will use default settings to install the software for this hardware device To install the software for your new hardware click Next lt Back Cancel 19 Installing the SYSMAC LINK PCI Drivers Section 3 2 Installation has been completed Add Remove Hardware Wizard RT Completing the Add Remove Hy Hardware Wizard NS The following hardware was installed Sysmac Link PCI Windows has finished installing the softwa
46. x1 e CD ROM x1 e Operation Manual x1 e Optical Fiber Cable Bracket x1 e Power supply connector x 1 e Board ID switch No indicator label x 1 e User registration card software user agreement x 1 Note 1 The CD ROM contains the following software e FinsGateway Version 3 PCI SLK e Setup Diagnostic Utility e C Library 2 This product does not include the personal computer OS One must be pro vided separately 1 2 Operating Environment The following table lists the operating environment for SYSMAC LINK Support Boards for PCI Bus connections Compatible computers Compatible OS Compatible language IBM PC AT or compatible e Windows 98 Microsoft Visual e CPU Intel Celeron 400 MHz or better e Windows 2000 C Ver 6 0 face Service Pack 3 e Main memory 32 MB minimum e Windows NT 4 0 e 1 or more PCI bus slots Service Pack 3 or later e Free hard disk space 70 MB min not including user applications e CD ROM drive Required for software installation e Display VGA 640 x 480 pixels min display Other conditions depend on the OS Note 1 SYSMAC LINK Support Boards for PCI Bus connection may not operate correctly when used with other computers or operating systems Always use the SYSMAC LINK Support Board with a personal computer and OS that satisfy the above conditions 2 The SYSMAC LINK Support Board cannot be used with Windows 95 or Win dows NT 3 51 or earlier Section 1 3

Download Pdf Manuals

image

Related Search

Related Contents

iGen3 Finishing Hints and Tips Guide September 2007    User`s Manual for - Sos electronic s. r. o.  MTD 6FE Snow Blower User Manual  Tristar VE-5952 fan  COLORrail IRC IP User Manual Rev. 4  USER`S MANUAL - Icon Heath & Fitness  Guía del usuario de 1500 Series  Chapter 3: BIOS Setup  FEIN Power Tools ASB 14V User's Manual  

Copyright © All rights reserved.
Failed to retrieve file