APC-3X95P_R 15”, 17”
Contents
1. APC 3X95P R 15 17 19 Intel 4 Core i3 i5 i7 IP65 69K Stainless Steel Panel PC User Manual Release Date Revision Mar 2015 V1 0 92015 Aplex Technology Inc All Rights Reserved Published in Taiwan Aplex Technology Inc 15F 1 No 186 Jian Yi Road Zhonghe District New Taipei City 235 Taiwan Tel 886 2 82262881 Fax 886 2 82262883 E mail aplex aplex com tw URL www aplextec com Revision History wen me msn 2015 03 27 Official Version APC 3X95P_R User Manual Warning This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions manual it may cause interference to radio communications It has been tested and found to comply with the limits for a Class A computing device pursuant to FCC Rules which are designed to provide reasonable protection against such interference when operated in a commercial environment Operation of this equipment in a residential area is likely to cause interference in which case the user at his own expense will be required to take whatever measures may be required to correct the interference Electric Shock Hazard Do not operate the machine with its back cover removed There are dangerous high voltages inside Caution Risk of explosion if the battery is replaced with an incorrect type Batteries should be recycled where possible Disposal of used batteries must be in accordance with2. 36 Enabled Disabled XHCI Hand off Enabled Disabled EHCI Hand off Disabled Enabled USB Mass Storage Driver Support Enabled Disabled USB hardware delays and time outs USB transfer time out 20 sec 10 sec 5 sec 1 sec Device reset time out 20 sec 10 sec 30 sec 40 sec Device power up delay Auto Manual 3 4 5 Super IO Configuration Super IO chip IT8518 IT8519 Serial Port O Configuration COM5 Device Mode Selection RS 485 RS 422 Serial Port 1 Configuration COMO Device Mode Selection RS 485 RS 422 APC 3X95P R User Manual 37 3 4 6 F81216 Second Super IO Configuration Super IO chip F81216 Second IO Serial Port O Configuration UART1 Mode Selection RS 232 RS 485 RS 422 Serial Port 1 Configuration Change Settings Auto Serial Port 2 Configuration Change Settings Auto Serial Port 3 Configuration Change Settings Auto 3 4 7 Intel R 82574L Gigabit Network Configuration 70 B3 D5 E7 3 4 8 Intel R 82574L Gigabit Network Configuration 70 B3 D5 E7 3 5 Chipset Settings Aptio Setup Utility Copyright C 2015 American Megatrends Inc Main Advanced Security Boot Save amp Exit PCH Parameters PCH IO Configuration C nm e AN ocml CN X mmi Ira tiemsr oaystem Agent SA Connguration Select Screen f Select Item Enter Select i Charge Opt F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save a
3. 5 08mm Pitch 1x3 Pin Connector DC9V 36V System power input connector APC 3X95P R User Manual 20 12 13 14 15 APC 3X95P R User Manual SBC 7110 i34010U 4G 180 Connector SBC 7110 154310U 4G 180 Connector BT1 BT2 Power on off button They are used to connect power switch button The two pins are disconnected under normal condition You may short them temporarily to realize system startup amp shutdown or awaken the system from sleep state LED2 LED3 LED4 LEDS LED2 LED STATUS Green LED for Motherboard EC status LED3 LED STATUS Green LED for Power status LED4 LED STATUS Green LED for Motherboard Standby Power Good status LED5 LED STATUS Green LED for CPU1 status HDMI1 HDMI 19P Connector High Definition Multimedia Interface connector JP6 21 16 U22 AT24CO2 DIP8 The EEPROM IC U22 is the set of LVDS resolution If you need other resolution settings please upgrade U22 data 1280 x 1024 Default SBC 7110 i34010U XX 800 x 480 option SBC 7110 i 54310U XX 800 x 600 option SBC 7110 i74510U XX 1024 x 768 option 1920 x 1080 option 17 INVT1 2 0mm Pitch 1x6 wafer Pin Header Backlight control connector for LVDS 18 CN1 1 25mm Pitch 2x20 Connector DF13 40P For 18 24 bit LVDS output connector Fully supported by Parad PS8625 DP to LVDS the interface features dual channel 24 bit output Low Voltage Differential Signaling A high speed low
4. G ANNUS l1 em Figure 1 9 Rear View of APC 3795P R APC 3X95P R User Manual 12 Figure 1 10 Front View of APC 3995P R d e Figure 1 11 Rear View of APC 3995P R APC 3X95P R User Manual 13 Chapter 2 Hardware 2 1 Mainboard Introduction SBC 7110 is a 4 industrial motherboard developed on the basis of Intel Haswell U Processors which provides abundant peripheral interfaces to meet the needs of different customers Also it features dual GbE ports 5 COM ports and one Mini PCIE configuration one eDP port one HDMI port one LVDS interface To satisfy the special needs of high end customers CN1 and CN2 and CN3 richer extension functions The product is widely used in various sectors of industrial control 2 2 Specifications Board Size 170mm x 113mm CPU Support Intel Core i3 4010U 1 7GHz onboard Intel Core i5 4310U 2 0 up to 3 00GHz option Intel Core i7 4510U 2 0 up to 3 10GHz option Chipset SoC Memory Support Onboard 4GB DDR3L SDRAM Graphics Intel HD Graphics 4400 Display Mode 1 x HDMI Port 1 x LVDS 18 24 bit dual LVDS 1 x eDP Port EDP1 option Support Up to 1920 x 1200 for HDMI Resolution Up to 1920 x 1200 for LVDS PS8625 Up to 1920 x 1200 for eDP Dual Display HDMI LVDS Super I O ITE IT8518E Fintek F81216AD BIOS AMI UEFI Storage 1 x SATAIII Connector 7P 1 x SATAIII Conn
5. No Save user Defaults Save Values as User Defaults Save configuration Yes No Restore user Defaults Restore User Defaults Restore User Defaults Yes No APC 3X95P_R User Manual 43 Chapter 4 Installation of Drivers This chapter describes the installation procedures for software and drivers under the windows 7 The software and drivers are included with the motherboard The contents include Intel CORE TM SoC chipset driver VGA driver LAN drivers Audio driver USB 3 0 Driver Intel AMT Driver Installation instructions are given below Important Note After installing your Windows operating system you must install first the Intel Chipset Software Installation Utility before proceeding with the installation of drivers WIN7 DRIVER DRIVERS Intel R CORE TM SoC Chipset Intel R VGA Chipset Intel R 82574L LAN Driver Realtek ALC662 HD Audio Driver USB 3 0 Driver Touch Panel Driver i Intel R AMT Driver APC 3X95P R User Manual 44 4 1 Intel R CORE TM SoC Chipset To install the Intel chipset driver please follow the steps below atep 1 Select Intel R CORE TM SoC Chipset from the list WIN7 DRIVER DRIVERS Intel R VGA Chipset Intel R 82574L LAN Driver Realtek ALC662 HD Audio Driver USB 3 0 Driver Touch Panel Driver Intel R AMT Driver Step 2 Click Next to setup program Intel R Chipset Device Software Welcome You are about to install the following product Intel R Chips
6. Pin1 Pin2 Pin3 Pin4 25 S 422 Switch COM1 setting it provides selectable RS232 or RS422 or RS485 serial signal output ON Pin1 Pin2 Pin3 Pin4 Pin5 26 COM1 Type DB9M Rear serial port standard DB9 Male serial port is provided to make a direct connection to serial devices COM1 port is controlled by pins No 1 6 of JP1 select output Signal RI or 5V or 12V For details please refer to description of JP1 and S 232 and S 422 setting APC 3X95P R User Manual 25 CTS Clear To Send JP1 select Setting RI 5V 12V BIOS Setup Advanced F81216 Super IO Configuration Serial Port O Configuration RS 232 0 Pw SmaMme 0 r 420 6 N Coo N 39 BIOS Setup Advanced F81216 Super IO Configuration Serial Port O Configuration RS 422 Pint Sume a 0 ee ee ee ee MN o8 0 0 0 NC e NC BIOS Setup Advanced F81216 Super IO Configuration Serial Port O Configuration RS 485 APC 3X95P R User Manual 26 27 JP2 2 0mm Pitch 2x3 Pin Header COM2 jumper setting pin 1 6 are used to select signal out of pin 9 of COM2 port Close 1 2 COM RI Ring Indicator default Close 3 4 COM Pin9 DC 5V option Close 5 6 COM Pin9 DC 12V option 28 COM2 Type DB9M Rear serial port standard DB9 Male serial port is provided to make a direct connection to serial devices mw Sigal Name 29 SATA P 2 5mm Pitch 1x2 box Pin Hea
7. The Rotate function is disabled if you use Monitor Mapping APC 3X95P R User Manual 81 5 2 2 Software Functions Projected Capacitive General In this window you can see there is USB Controller Click OK to continue eGalaxTouch USB Controller General Setting Tools Display Hardware About Installed Tauchscreen Controllers Q gt USE USB Controller Monitor Add nU Mapping Cancel Faje Monitor Mapping to adjust touch panel Add to search for device APC 3X95P_R User Manual 82 Setting eGalaxTouch USB Controller Beep F a WwW Beep On Touch cancion QE Duration iw Beep From System Beep Beep From Sound Card Beep On Release oa Double Click Time Sharterz z PP Longer Double Click Area Smaller lt ESSE LL gt gt Bigger zy Normal Made Option es ams Beep Beep On Touch Beep On Release Beep From System Beep Beep From Sound Card Linearization Style 9 points 25 points Double Click Time Shorter Longer Double Click Area Smaller Bigger Normal mode Simulate the mouse mode APC 3X95P R User Manual Iw Enable Auto Right Click Iw Enable Touch W Enable Cursor Stabilization Constant Touch Area b Smaller lt 5 gt gt Bigger Auto Aight Click Time 1000 ms Shorter z A gt gt Longer cea s Option Function Enable Constant Touch Enable Auto Right Click Enable Touch Enable Curs
8. VGA Chipset Realtek ALC662 HD Audio Driver USB 3 0 Driver Touch Panel Driver Intel R AMT Driver OTHERS User Manual APC 3X95P_R User Manual 50 Step 2 Click Next 35 Intel R Network Connections Install Wizard Welcome to the install wizard for Intel R a Network Connections i intel Installs drivers Intel R Network Connections and Advanced Networking Services WARNING This program is protected by copyright law and international treaties Step 3 Read license agreement Click accept the terms in the license agreement Click Next JH Intel R Network Connections Install Wizard License Agreement Please read the following license agreement carefully INTEL SOFTWARE LICENSE AGREEMENT IMPORTANT READ BEFORE COPYING INSTALLING OR USING Do not copy install or use this software and any associated materials collectively the Software provided under this license agreement Agreement until you have carefully read the following terms and conditions By copying installing or otherwise using the Software you agree to be bound by the terms of this Agreement If you do not agree to the terms of this Agreement yr Ido not accept the terms in the license agreement APC 3X95P R User Manual 51 Step 4 Click Next to continue Intel R Network Connections Install Wizard Select the program features you want installed Install Drivers v Intel R PROSet for Windows Dev
9. intel Welcome to the Setup Program inte This setup program will install the Intel Management Engine Components It is strongly recommended that you exit all programs before continuing Click Next to continue Intel Installation Framework APC 3X95P_R User Manual 58 Step 3 Read the License Agreement and then click Yes to continue Intel Management Engine Components License Agreement You must accept all of the terms of the license agreement in order to continue the setup program Do you accept the terms INTEL SOFTWARE LICENSE AGREEMENT OEM IHV ISV Distribution amp Single User P IMPORTANT READ BEFORE COPYING INSTALLING OR USING L3 Do not use or load this software and any associated materials collectively the Software until you have carefully read the following terms and conditions By loading or using the Software you agree to the terms of this Agreement If you do not wish to so agree do not install or use the Software Please Also Note f you are an Original Equipment Manufacturer OEM Independent Hardware Vendor IHV or Independent Software Vendor ISV this complete LICENSE AGREEMENT applies f you are an End User then only Exhibit A the INTEL SOFTWARE LICENSE AGREEMENT es Intel Installation Framework Step 4 Click Next to continue Intel Management Engine Components Setup Progress Please wait while the following setup operations are performed Crea
10. 1 3 Dimensions deu ah ate Al re atl ae Oe ee UNIT mm Tolerance 0 5 Figure 1 1 Dimensions of APC 3595P R UNIT mm Tolerance 0 5 Figure 1 2 Dimensions of APC 3795P R APC 3X95P_R User Manual 9 Tolerance t 5 Figure 1 3 Dimensions of APC 3995P UNIT mm Tolerance 0 5 Figure 1 4 Dimensions of APC 3995R APC 3X95P R User Manual 10 1 4 Brief Description of APC 3X95P R APC 3X95P 3X95R series are powered by Intel 4 Core i3 i5 i7 Processor It is a full flat bezel designed and totally IP65 69K certificated fanless high performance panel PC The stainless steel chassis design makes it exceptionally suitable for strict hygiene regulations for food chemical industry medical restaurant kitchen applications storage management and outdoor information segment and so on APC 3X95P 3X95R series has touch screen of projected capacitive type and resistive type window for option The model supports 4GB DDR3 1333 1600MHz onboard and 1 x 2 5 SATA HDD or SSD easily accessible design and it is 9 36V DC wide ranging power input APC 3X95P 3X95R series supports OS such as Windows 7 Professional for Embedded Systems Windows 7 Ultimate for Embedded Systems and so on APC 3X95P R User Manual 11 La Figure 1 8 Front View of APC 3795P R a e o o oe oe e HE yy i gt gt tE LI 3 1 Dc 9 usa use com cone A
11. 4 0 506 oetup Wizard PenMount Windows Universal Driver WHOoL vz 4 0 306 has been installed an your computer Click Finish to close this wizard Cancel 5 1 2 Installing Software Projected Capacitive Step 1 Insert the product CD the screen below would appear Click touch panel driver from the list z 4 Ya M N RON aN oT A strial Panel PG WIN7 DRIVER DRIVERS Intel R CORE TM SoC Chipset nau Intel R VGA Chipset Intel R 82574L LAN Driver Realtek ALC662 HD Audio Driver USB 3 0 Driver Intel R AMT Driver APC 3X95P_R User Manual 65 Step 2 Select Projected Capacitive DRIVERS Resistive Touch Step 3 Click Next to continue eGalaxTouch Welcome to the InstallShield Wizard for eGalaxT ouch The InstallShield Wizard will install eG alas Touch on your computer To continue click Next Cancel APC 3X95P_R User Manual 66 Step 4 Select accept the terms of the license agreement Click Next License Agreement Please read the following license agreement carefully Declaration and Disclaimer The programs including but nat limited to software and ar firmare hereinafter referred to Programe ar PROGRAMS are owned by elala eMPIA Technology Inc hereinafter referred to EETI and are compiled from EET Source cade EETI hereby grants to licensee a personal non exclusive non transferable license to copy use and create derv
12. PIN6 Switch ATX Power and Auto Power on jumper setting 5 a2a Swith o6 of Pin6 On Auto Power on Default 6 PS ON option 2 0mm Pitch 1x2 Pin wafe Header ATX Power and Auto Power on jumper setting Aw Mee Close 1 2 Auto Power on Default 7 BAT1 1 25mm Pitch 1x2 Wafer Pin Header 3 0V Li battery is embedded to provide power for CMOS Signal Name VBAT 8 JP3 2 0mm Pitch 1x2 Pin Header CMOS clear jumper CMOS clear operation will permanently reset old BIOS settings to factory defaults NORMAL Default Close 1 2 Clear CMOS Procedures of CMOS clear S a Turn off the system and unplug the power cord from the power outlet b To clear the CMOS settings use the jumper cap to close pins 1 and 2 for about 3 seconds then reinstall the jumper clip back to pins open c Power on the system again d When entering the POST screen press the lt ESC gt or lt DEL gt key to enter CMOS Setup Utility to load optimal defaults e After the above operations save changes and exit BIOS Setup APC 3X95P_R User Manual 19 9 BAT2 2 0mm Pitch 1x10 Wafer Pin Header Smart battery Interface mw SewWme Hm BOT sw m BALTMP SET BAT1 ON 10 BAT LED 2 0mm Pitch 1x4 Wafer Pin Header The Charge status indicator for BAT2 Pin1 Pin3 Charge LED status Pin2 Pin3 Discharge LED status Pin4 Pin3 EC LED status mw SmuNme om LE 11 DC IN1
13. Program This setup program will install the following components Intel Graphics Driver Intel Display Audio Driver It is strongly recommended that you exit all programs before continuing Click Next to continue Intel Graphics Driver License Agreement You must accept all of the terms of the license agreement in order to continue the setup program Do you accept the terms INTEL SOFTWARE LICENSE AGREEMENT OEM IHV ISV Distribution amp Single User until you have carefully read the following terms and conditions By loading or using the Software you agree to the terms of this Agreement If you do not wish to so agree do not install or use the Software Please Also Note f you are an Original Equipment Manufacturer OEM Independent Hardware Vendor IHV or Independent Software Vendor ISV this complete LICENSE AGREEMENT applies If you are an End User then only Exhibit A the INTEL SOFTWARE LICENSE AGREEMENT Temm Intel Installation Framework APC 3X95P_R User Manual Step 4 Click Next to continue Intel Graphics Driver intel Readme File Information Refer to the Readme file below to view the system requirements and installation information README FILE Release Version Production Version Operating System s m Intel Installation Framework Intel Graphics Driver Setup Progress Please wait while the following setup operations are performed Copyi
14. point calibration Question L APC 3X95P R User Manual 71 5 2 Software Functions 5 2 1 Software Functions Resistive Touch Upon rebooting the computer automatically finds the new 6000 controller board The touch screen is connected but not calibrated Follow the procedures below to carry out calibration 1 After installation click the PenMount Monitor icon PM in the menu bar 2 When the PenMount Control Panel appears select a device to Calibrate PenMount Control Panel Resistive Touch The functions of the PenMount Control Panel are Device Multiple Monitors Tools and About which are explained in the following sections Device In this window you can find out that how many devices be detected on your system PenMount Control Panel Saks Device Multiple Monitors Toals About Select a device to configure FenMount 6000 USE Configure Refresh Calibrate This function offers two ways to calibrate your touch screen Standard Calibration adjusts most touch screens Advanced Calibration adjusts aging touch screens APC 3X95P_R User Manual 72 Standard Calibration Click this button and arrows appear pointing to red squares Use your finger or stylus to touch the red squares in sequence After the fifth red point calibration is complete To skip press ESC Advanced Calibration Advanced Calibration uses 4 9 16 or 25 points to effectively calibrate touch panel lin
15. power data transmission standard used for display connections to LCD panels 12V SO 12V SO reno a 3 SKLERL Gem 5 5 Ground APC 3X95P R User Manual 22 1587 UPA open UPA open LPoweritb PWRitb 40 39 Ground Fowerib 19 EDP1 option e eop voos ono oeo Ground EDP AUN EDP AUX P asa nasa wosvoos s 7 wos voos wosvoos 10 o wbsvbpi di LVDS EDP TXN 2 EDP TXN O EDP TXP 2 EDP TXP O UJ EDP TXN 3 EDP TXP 3 EDP DISP UTIL EDP AUX N EDP AUX P 12C1 SCL 12C APC 3X95P_R User Manual 23 UQJ Q QGO N2J N2 N29 N N2 L2 IHP Imnp mnp USB7 USB7 P ETE N option option 5V S5 USB 5VS5USB 20 JP4 2 0mm Pitch 2x2 wafer Pin Header USB3 CN1 or Touch jumper setting USB7 CN1 Touch TCH1 21 TCH1 2 0mm Pitch 1x6 wafer Pin Header internal Touch controller connector 22 LED1 LED1 LED STATUS Green LED for Touch Power status 23 JP1 2 0mm Pitch 2x3 Pin Header COM1 jumper setting pin 1 6 are used to select signal out of pin 9 of COM1 port Close 1 2 COM1 RI Ring Indicator default Close 3 4 COM1 Pin9 DC 5V option Close 5 6 COM1 Pin9 DC 12V option APC 3X95P_R User Manual 24 24 S 232 Switch COM1 jumper setting it provides selectable RS232 or RS422 or RS485 serial signal output RS232 Default ON Pin1 Pin2 Pin3 Pin4 RS422 option OFF Pin1 Pin2 Pin3 Pin4 RS485 option OFF
16. the Enable Multiple Monitor Support box then click Map Touch Screens to assign touch controllers to displays d PenMount Control Panel EIE Calibrate Draw Multiple Monitors Option About l Enable Multiple Monitor Support 2 When the mapping screen message appears click OK APC 3X95P R User Manual 78 PenMount Control Panel Calibrate Draw Multiple Monitors Option About iw Enable Multiple Monitor Support 3 Touch each screen as it displays Please touch this monitor Following this sequence and touching each screen is called mapping the touch screens 4 Touching all screens completes the mapping and the desktop reappears on the monitors 5 Select a display and execute the Calibration function A message to start calibration appears Click OK Calibrate To start calibration please touch the pane to calibrate in the following screen wj APC 3X95P R User Manual 79 6 Touch this screen to start its calibration appears on one of the screens Touch the screen 7 Touch the red square messages appear Touch the red squares in sequence 8 Continue calibration for each monitor by clicking Standard Calibration and touching the red squares NOTES 1 If you use a single VGA output for multiple monitors please do not use the Multiple Monitor function Just follow the regular procedure for calibration on each of your desktop monitors 2 The Rotating fu
17. the first time is as follows and includes basic information on BIOS CPU memory and storage devices 3 2 BIOS Setup Utility Press Delete key to enter BIOS Setup utility during POST and then a main menu containing system summary information will appear APC 3X95P_R User Manual 32 3 3 Main Settings System Language English System Date Thu 01 01 2008 System Time 00 00 18 System Time Set the system time the time format is Hour 0 to 23 Minute Oto59 Second Oto59 System Date Set the system date the date format is Day Note that the Day automatically changes when you set the date Month 01 to 12 Date 01 to 31 Year 1998 to 2099 APC 3X95P_R User Manual 33 3 4 Advanced Settings Aptio Setup Utility Copyright C 2015 American Megatrends Inc Main Chipset security Boot Save amp Exil System ACPI Parameters Version 2 17 1246 Copyright C 2015 American Megatrends Inc 3 4 1 ACPI Settings Enable ACPI Auto Conf Disabled Enabled Enable Hibernation Enabled Disabled ACPI Sleep State S1 only CPU Stop Clock S3 Suspend to RAM Suspend Disabled Both S1 and S3 available for OS to choose from Lock Legacy Resources Disabled Enabled APC 3X95P_R User Manual 34 S3 Video Repost Disabled Enabled ACPI Low Power SO Idle Disabled Enabled 3 4 2 CPU Configuration Intel R Core TM i5 4310U 2 00GHz CPU Signature Processor Family Micr
18. 00 Bottom faso Drag Working amp rea Top Other Other mode of display Quarter1 4 and Customized area Drag Active Area Active Area Drag active area to enable Active Area Function APC 3X95P_R User Manual Hardware eGalaxTouch USB Controller Controller Model PCAPY 200 Seres Firmware Version 1030 Hardware Calibration canci boob Saturn Hardware Configuration Saturn Hardware Configuration Saturn Saturn Hardware Configuration Improper Setting May Cause Touch malfunction Sensitivity Delay Time Shorter lt gt gt Longer Reset all of the control parameters to Factory default setting APC 3X95P_R User Manual 88 About To display information about eGalaxTouch and its version eGalaxTouch USB Controller Touch Screen Utility Q gt Copyright C 2000 2011 eGalax Touch eGalas eMPIA Technology Inc Version 5 11 0 81 25 We provide a full range of controllers for both analog resistive and capacitive touch panels The resistive controller cammunicates with the PC system directly through H8232 P5 2 or USB part The design ix optimized for an accurate sensitive and quick touch performance as well as an ease of use interface The driver supports a set of operating systems Le Windows A 2000 Windows Al ARP Windows Vista Al wind s l gt RN APC 3X95P R User Manual 89
19. 1 USB3 2 Double stack USB type A Rear USB connector it provides up to two USB3 0 ports High speed USB 2 0 allows data transfers up to 480 Mb s USB3 0 allows data transfers up to 5 0Gb s support USB full speed and low speed signaling USB3 1 USB3 0 USB3 2 USB3 0 Each USB Type A Receptacle 2 Ports Current limited value is 1 5A If the external USB device current exceeds 1 5A please separate connectors into different Receptable 38 LAN1 LAN2 LAN1 LAN 2 RJ45 Connector Rear LAN port Two standard 10 100 1000M RJ 45 Ethernet ports are provided Used intel 82574L chipset LINK LED green and ACTIVE LED yellow respectively located at the left hand and right hand side of the Ethernet port indicate the activity and transmission state of LAN ae OO pi LAN1 uin LAN2 39 BUZ1 Onboard buzzer 40 CN2 DF13 30P Connector For expand output connector It provides eight GPIO one RS422 or RS485 one USB2 0 one Power on off one Reset PCH GPIO49 GPIOIN2 4 3 GPIO IN PCH GPIO48 PCH GPIO51 GPIO INA 6 5 GPIO IN3 PCH GPIOS5O APC 3X95P R User Manual 20 Foros emoon s 7 ero oon Pon Gros Pen sross cmooum 10 s cmo ours Po amp GPOsM eens nin sw 485 or 422 14 13 485 or 422 16 15 COMS ov COMS BIOS Setup Advanced Super IO Configuration Serial PortO Configuration RS 422 Advanced Super IO Configuration Serial Port O Configuration RS 485 COMO BIOS Setup Advanc
20. 71 InstallShield Wizard Complete The InstallShield Wizard has successfully installed Realtek High Definition Audio Drrver Before sEart pour computer OF es want to restart my computer now al Mo will restart my computer later Hemove any disks fram their dives and then click Finish to complete setup InstallShield Back Finish Cancel APC 3X95P R User Manual 54 4 5 USB 3 0 Driver To install the USB 3 0 Driver please follow the steps below Step 1 Select USB 3 0 Driver from the list DA M In dustrial Panel PG WIN7 DRIVER DRIVERS Intel R CORE TM SoC Chipset Intel R VGA Chipset Intel R 82574L LAN Driver Realtek ALC662 HD Audio Driver Touch Panel Driver Intel R AMT Driver OTHERS User Manual iit m View EXIT Welcome to the Setup Program This setup program will install the following components Intel USB 3 0 eXtensible Host Controller Driver Intel USB 3 0 Hub Driver Intel USB 3 0 Host Controller Switch Driver Intel USB 3 0 Monitor Click Next to continue ee nnm Intel Installation Framework APC 3X95P_R User Manual Step 3 Read the license agreement Then click Yes to continue XE am IE ate ee ae m a 7 DOT Intel Installation Framewo Intel USB 3 0 eXtensible Host Controller Driver license Agreement You must accept all of the terms of the license agreement in order to continue the setup program Do you a
21. E STEEP ESSE ESE SE EEE ASE EES SE EEE AE EES TS NOTE For the list of supported chipsets please refer to the Release Notes SEEEEADEEPEATEELEATEELATPELSE TEEPE ASTELE TERESA TELE ATTA ASTPESAST ELE A EEE ASST CONTENTS OF THIS DOCUMENT SEEEEADEPEATEEELSEAETEELATPESCESEEPEATELE TERESA TELE ADEE ET ASE ESAT ELTA EEE ASS This document contains the following sections 1 Overview 2 System Requirements 3 Contents of the Distribution Package 34 Public and NDA Configurations A Il ld I B a 1 47 ng I F7 Q2 uL oll oe ll l APC 3X95P_R User Manual 46 Step 5 Click Finish to complete the setup process Intel R Chipset Device Software Completion You have successfully installed the following product Intel R Chipset Device Software Press Finish to complete the setup process EE 4 2 Intel R VGA Chipset To install the VGA drivers follow the steps below to proceed with the installation Step 1 Select Intel R VGA Chipset from the list i m Et Industrial Panel PG WIN7 DRIVER DRIVERS Intel R CORE TM SoC Chipset Intel R 82574L LAN Driver Realtek ALC662 HD Audio Driver USB 3 0 Driver Touch Panel Driver Intel R AMT Driver APC 3X95P_R User Manual 47 Step 2 Click Automatically run WinSAT and enable the Windows Aero desktop theme if supported Click Next Intel Graphics Driver Welcome to the Setup
22. ace Storage 1 x 2 5 SATA HDD or SSD easily accessible design 1 x Internal SD Card slot onboard Expansion Slot 1 x Mini PCle half size APC 3X95P R User Manual 7 for option WLAN BT Module and Antenna at rear side 15 TFT LCD 19 TFT LCD 1024 x 768 1280 x 1024 16 7M 16 7M 800 1 1000 1 160 H 160 V 170 H 165 V 50 000 hrs 50 000 hrs Touch Screen Resistive Touch Window Type APC 3595R APC 3995R USB 80 Display Display Type Max Resolution Max Color Luminance Contrast Ratio Viewing Angle Backlight Lifetime Model no Interface Light Transmission Touch Screen Projected Capacitive Type Model no APC 3595P APC 3795P APC 3995P Interface USB 9096 Light Transmission Power Input 9 36V DC Structure Stainless Steel Chassis Mounting VESA Mount 75 x 75 VESA Mount 100 x 100 IP Rating Total IP65 IP69K 432 x 358 x 56 Dimension mm 399 x 323 9 x 48 5 470 x 415 4 x 60 Operating System Support OS Support Windows 7 Professional for Embedded Systems Windows 7 Ultimate for Embedded Systems Windows Embedded 8 Standard Windows Embedded 8 Pro Windows Embedded 8 1 Pro Windows Embedded 8 1 Industry Pro Environmental 0750 C 20C 60 C with industrial SSD for 15 and 17 option 30 770 C 10 to 9096 40 C non condensing CE FCC Class A Operating temperature Extended Temperature Storage temperature Storage humidity Certification APC 3X95P R User Manual 8
23. ative works of Programs Far the sole purpose in conjunction with an EETI Praduct including but nat limited to integrated circuit and or controller Any reproduction copies modification translation compilation application ar representation of Programs except as specified above iz prohibited without the express written permission by EETI Disclaimer EETI MARES NHO WARRANTY OF ANY KIND ESPRESS OR IMPLIED C da nat accept the terms of the license agreement Step 5 Click Next to continue eGalaxTouch Setup Type Select the setup type that best suits your needs Extra F5 2 interface driver for eGalax Touch controller Please check the check box for P5 2 touch controller APC 3X95P_R User Manual 67 Step 6 Click Install RS232 interface driver Then click Next to continue eGalaxTouch Setup Type Select the setup type that best suits your needs Extra AS24232 interface driver for eGalasT ouch controller Please check the check box for H8 Z32 touch controller Step 7 Select None Click Next eGalaxTouch Setup Type Select the setup type that best suits your needs Do 4 paint calibration after system reboot Every system boot up O Nest system boot up APC 3X95P_R User Manual 68 Step 8 Click OK to continue eGalaxTouch InstallShield Wizard i IF vou are trying to install the USB touch device please make sure that your touch monitor or touch controller s USB cable is plugged int
24. ccept the terms INTEL SOFTWARE LICENSE AGREEMENT OEM IHV ISV Distribution amp Single User IMPORTANT READ BEFORE COPYING INSTALLING OR USING Do not use or load this software and any associated materials collectively the Software until you have carefully read the following terms and conditions By loading or using the Software you agree to the terms of this Agreement If you do not wish to so agree do not install or use the Software IHV or Independent Software Vendor ISV this complete LICENSE AGREEMENT applies If you are an End User then only Exhibit A the INTEL SOFTWARE LICENSE AGREEMENT m Intel Installation Framework Step 4 Click Next to continue Intel USB 3 0 eXtensible Host Controller Driver Readme File Information Refer to the Readme file below to view the system requirements and installation information installation please copy driver files to a local hard drive folder and run from there Microsoft Windows 7 Intel Installation Framework APC 3X95P_R User Manual 56 Step 5 Click Next to continue C Program FilesVntelntel R USB 3 0 eXtensible Host Controller Driver Applica C Program Files Intel Intel R USB 3 0 eXtensible Host Controller Driver VApplica C Program Files Intel Intel R USB 3 0 eXtensible Host Controller Driver VApplica C Program Files Intel Intel R USB 3 0 eXtensible Host Controller Driver Applica C Program Fil
25. ced Calibration Tum off EEPROM storage NOTE Recommend to use a stylus during Advanced Calibration for greater accuracy APC 3X95P_R User Manual 75 Plot Calibration Data Check this function and a touch panel linearity comparison graph appears when you have finished Advanced Calibration The blue lines show linearity before calibration and black lines show linearity after calibration Turn off EEPROM The function disable for calibration data to write in storage Controller The default setting is Enable Setting PA Device 0 PenMount 6000 USB Calibrate Setting About Touch Mode Beep Sound Beep Mode iw Cursor Stabilizer v Use press and hold as right click p You can use Cursor 20 sec Y Stabilizer to remove pter of cursor Back to Defaut APC 3X95P R User Manual 76 Touch Mode This mode enables and disables the mouse s ability to drag on screen icons useful for configuring POS terminals Mouse Emulation Select this mode and the mouse functions as normal and allows dragging of icons Click on Touch Select this mode and mouse only provides a click function and dragging is disables Beep Sound Enable Beep Sound turns beep function on and off Beep on Pen Down beep occurs when pen comes down Beep on Pen Up beep occurs when pen is lifted up Beep on both beep occurs when comes down and lifted up Beep Frequency modifies sound frequency Beep Duration modif
26. der One onboard 5V output connector are reserved to provide power for SATA devices S Note ar Output current of the connector must not be above 1A APC 3X95P R User Manual 27 30 31 32 33 34 35 36 SATA2 SATA 7Pin SATA Connectors one SATA connector are provided with transfer speed up to 6 0Gb s SATA1 SATA 7Pin 15Pin SATA Connectors one SATA connector are provided with transfer speed up to 6 0Gb s SD1 SD card slot Secure Digital Memory Card socket MPCIE1 Socket 52Pin mini PCle socket it is located at the top it supports mini PCle devices with USB2 0 and LPC and SMBUS and PCle signal MPCle card size is 30 x 50 95mm H1 H2 MPCIE1 SCREW HOLES H1 and H2 for mini PCIE card 30mm x 50 95mm assemble AUDIO1 2 0mm Pitch 2x6 Pin Header Front Audio An onboard Realtek ALC662 VD codec is used to provide high quality audio I O ports Line Out can be connected to headphone or amplifier Line In is used for the connection of external audio source via a Line in cable MIC is the port for microphone input audio Signal Name Pin Ping Signal Name 5V GND AUD LINE OUT L EN LINE OUT R s uum s en n LINE_OUT Diameter 3 5mm Jack HD Audio port An onboard Realtek ALC662 VD codec is used to provide high quality audio I O ports Line Out can be connected to a headphone or amplifier APC 3X95P_R User Manual 28 Line out 37 USB3 USB3
27. earity of aged touch screens Click this button and touch the red squares in sequence with a stylus To skip press ESC Step 1 Please select a device then click Configure You can also double click the device too PenMount Control Panel ej Device Multiple Monitors Tools About Select a device to configure FenMount 6000 USE Configure Refresh APC 3X95P_R User Manual 73 Step 2 Click Standard Calibration to start calibration procedure A Device 0 PenMount 6000 USB Calibrate Setting About Standard Calibration Tum off EEPROM storage NOTE The older the touch screen the more Advanced Mode calibration points you need for an accurate calibration Use a stylus during Advanced Calibration for greater accuracy Please follow the step as below APC 3X95P_R User Manual Step 3 Come back to PenMount Control Panel and select Tools then click Advanced Calibration PenMount Control Panel ARH Device Multiple Monitors Tools About Draw Test by drarwing on the touch screen ea Turn ORNJOFF Advanced Calibration Made Show Hide the icon For switching buttons Zz Right Button Icon f Desktop System Tray Back to Default OK Step 4 Select Device to calibrate then you can start to do Advanced Calibration 4 Device 0 PenMount 6000 USB Calibrate Setting About Advanced Mode 9 Plot calibration data Standard Calibration Advan
28. ector 7P 15P 1 x SD Slot APC 3X95P R User Manual 14 Ethernet 2 x PCle Gbe LAN by Intel 82574L USB 2 x USB 3 0 type A stack ports USB3 USB 3 0 USB3 1 USB3 2 USB 2 0 USB1 USB2 2 x USB 2 0 Pin header for CN3 USB3 USB4 1 x USB 2 0 Pin header for CN2 USB5 1 x USB 2 0 Pin header for CN1 USB7 or Touch option 1 x USB 2 0 for MPCIE1 USB8 Serial 1 x RS232 RS422 RS485 port DB9 connector for external COM1 Pin 9 w 5V 12V Ring select 1 x RS232 port DB9 connector for external COM2 Pin 9 w 5V 12V Ring select 2 X UART for CN3 COM3 COM4 1 x RS422 485 header for CN2 IT8518E COMS 1 x RS422 485 header for CN2 IT8518E COM6O option Digital I O 8 bit digital I O by Pin header CN2 4 bit digital Input 4 bit digital Output 4 bit digital I O by Pin header CN3 2 bit digital Input 2 bit digital Output Battery Support CR2477 Li battery by 2 pin header BAT1 CMOS Smart Battery 1 x Smart battery Support 3 Serial Li battery by 10 pin header BAT2 Audio Support Audio via Realtek ALC662 VD HD audio codec Support Line in Line out MIC by 2x6 pin header Keyboard Mouse 1 x PS2 keyboard mouse by box pin header CN3 Expansion Bus 1 x mini PCl express slot 1 x PCl express CN3 Touch Ctrl 1 x Touch ctrl header for TCH1 ITE8518E COM6 JP4 setting RS232 or USB 2 0 Power Wide Range DC9V 36V input Management 1 x 3 pin power inp
29. ed Super IO Configuration Serial Port 1 Configuration RS 422 Advanced Super IO Configuration Serial Port 1 Configuration RS 485 04 13 16 15 a8 7 coms coMe 2n 24 23 41 EC GPIO 2 0mm Pitch 1x10 Pin Header For expand connector It provides eight GPIO Aw Sanaa 4 KG r ke s KG 3 EG APC 3X95P R User Manual 30 42 CN3 1 27mm Pitch 2X30 Female Header For expand output connector It provides four GPIO two USB 2 0 0ne PS 2 mouse one PS 2 keyboard two uart one PClex1 one SMbus It s connected to the TB 528 riser Card ff sesws a 2 seu SVSSUSP sess usc mONAX T COMA RI COMA DCD COM4 COM4_TXD COM4_RXD COM4 UART UART Ooo croma 25 e oa UART UART o wem 39 40 Ground PORLRKNO as aa PELRO CuCioOM PEL N 47 48 CUCIO0M PEL P pcer waen 49 50 PLLIST BUFI vc amu sa 5 Gem aravss Ss 56 PWRBINON Power Auto on smvs sr se rvs iw wo s oo ues w APC 3X95P_R User Manual 3 Chapter 3 BIOS Setup 3 1 Operations after POST Screen After CMOS discharge or BIOS flashing operation press Delete key to enter CMOS Setup E American Megatrends Version 2 17 1246 Copyright C 2014 American Megatrends Inc BIOS Date 01 05 2015 10 27 48 Ver 7110V008 Press DEL or ESC to enter setup After optimizing and exiting CMOS Setup the POST screen displayed for
30. ersal Driver WHOL Y2 4 0 306 It is recommended that vau close all other applications before starting Setup This will make it possible to update relevant system Files without having to reboot your computer Click Mexk bo continue APC 3X95P_R User Manual 62 Step 4 Read the license agreement Click Agree to agree the license agreement PenMount Windows Universal Driver WHOL V2 4 0 306 Setup eX EJ License Agreement Please review the license terms before installing PenMount Windows Universal E Driver WHOL v2 4 0 306 Press Page Down to see Ehe rest of the agreement PLEASE READ THE LICENSE AGREEMENT Penklount touch screen driver sofbware is only for using wath PenMount touch screen controller or control board Ary person or company using a Penklount driver on any piece of equipment which does not utilize an Fenbfount touch screen controller will be prosecuted to the full extent of the law IF you accept the terms of the agreement click I Agree to continue You must accept the agreement to install PenMount Windows Universal Driver HOL Y2 4 0 306 Step 5 Choose the folder in which to install PenMount Windows Universal Driver Click Install to start the installation PenMount Windows Universal Driver WHQL V2 4 0 306 Setup X Choose Install Location Choose the Folder in which to install PenMount Windows Universal Driver w HOLY Bs v2 4 0 306 ceil Setup will install PenMounk Windows Universa
31. es ntellntel R USB 3 0 eXtensible Host Controller Driver Applica C Program Files Intel Intel R USB 3 0 eXtensible Host Controller Driver VApplica C Program Files Intel Intel R USB 3 0 eXtensible Host Controller Driver VApplica C Program Files Intel Intel R USB 3 0 eXtensible Host Controller Driver VApplica C Program Files Intel Intel R USB 3 0 eXtensible Host Controller Driver VApplica Creating Registry Key HELMYSOFTWAREMicrosaft Windows CurrentVersion Run VSGMON Click Mext to continue 4 a HT Intel Installation Framework Step 6 Select Yes want to restart this computer now Then click Finish to complete the installation Intel USB 3 0 eXtensible Host Controller Driver Setup Is Complete You must restart this computer for the changes to take effect Would you like to restart the 7 No I will restart this computer later Click Finish then remove any installation media from the drives Intel Installation Framework APC 3X95P_R User Manual 57 4 6 Intel R AMT Driver To install the Intel R AMT Driver please follow the steps below Step 1 Se Ec Industrial Panel PG WIN7 DRIVER DRIVE RS Intel R CORE TM SoC Chipset Intel R VGA Chipset Intel R 82574L LAN Driver Realtek ALC662 HD Audio Driver USB 3 0 Driver Touch Panel Driver OTHERS User Manual RN View EXIT EE Step 2 Click Next to continue Intel Management Engine Components
32. et Device Software It is strongly recommended that you exit all programs before continuing Press Next to continue or press Cancel to exit the setup program APC 3X95P_R User Manual 45 Step 3 Read the license agreement Click Accept to accept all of the terms of the license agreement Intel R Chipset Device Software License Agreement INTEL SOFTWARE LICENSE AGREEMENT OEM THY ISV Distribution amp Single User IMPORTANT READ BEFORE COPYING INSTALLING OR USING Do not use or load this software and any associated materials collectively the Sottware until you have carefully read the following terms and conditions By loading or using the Software you agree to the terms of this Agreement If you do not wish to so agree do not install or use the Software Please Also Nate f you are an Original Equipment Manufacturer OEM Independent Hardware Vendor HV or Independent Software Vendor ISV this complete LICENSE AGREEMENT applies f you are an End User then only Exhibit A the INTEL SOFTWARE LICENSE AGREEMENT applies Aya JL d li E EE EZE EZE Step 4 Click Install to begin the installation Intel R Chipset Device Software Readme File Information SESEADEEEASEEEEAEEEASTEESE EEE ESSE ESE EEE SAS EEE SEE EES SE EES SEE EES EEE SS SE Product Intel R Chipset Device Software Version 10 0 Target PCH Chipset Mixed Platform Date 2014 04 24 BEERS e a a SEP ESESEESE
33. hapter describes how to install drivers and other software that will allow your touch screen work with different operating systems 5 1 Windows XP 2003 Vista WIN7 Universal Driver Installation for PenMount 6000 Series Before installing the Windows XP 2003 Vista WIN7 driver software you must have the Windows XP 2003 Vista WIN7 system installed and running on your computer You must also have one of the following PenMount 6000 series controller or control boards installed PM6500 PM6300 5 1 1 Installing Software Resistive Touch If you have an older version of the PenMount Windows WIN7 driver installed in your system please remove it first Follow the steps below to install the PenMount DMC6000 Windows WIN7 driver Step 1 Insert the product CD the screen below would appear Click Touch Panel Driver from the list EA See E Industrial Panel PG WIN7 DRIVER DRIVERS Intel R CORE TM SoC Chipset Intel R VGA Chipset Intel R 82574L LAN Driver Realtek ALC662 HD Audio Driver USB 3 0 Driver Intel R AMT Driver APC 3X95P_R User Manual 61 Step 2 Select Resistive Touch 9 e Industrial Panel PG Touch Driver Projected Capacitive Step 3 Click Next to continue PenMount Windows Universal Driver WHQL V2 4 0 306 Setup E X Welcome to the PenMount Windows Universal Driver WHQL V2_ 4 0 306 Setup Wizard This wizard will guide you through the installation of PenMount Windows Univ
34. i E ii BO Oh e EDP gt Ta barre lonis 2 ea cmb z O06 00000 00 000 00 00000 009 ja EE O He 34 HL O a 16 6 zn 2 iy LET 22 FELEDI t a EE nl 13 X 5 RUMINUS en E c EG sn 32 D III l HPCE 33 3 o E We Cm mec Tm 402 oooooD oooon E 40 amp 4220 S 23 B LIBI 500006 666 SBC 7ll6 39 wa E n _ 25 24 P i Rev 1 00 im i 35 Ss 10 41 O LANI LAN AUDI JPl JPZ BAT LED EC GPID D usn C poscod D desc gneeo jjneeob oooo Li FOEO ww C HINT OO 38 ege itm M Figure 2 3 Jumpers and Connectors Location Board Bottom APC 3X95P R User Manual 17 2 4 Jumpers Setting and Connectors 1 CPU1 FCBGA1168 onboard Intel Haswell U Processors Model Processor SBC 7110 i34010P 4G i3 4010U 1 7GHz SBC 7110 i54310P 4G i5 4310U 2 0 up to 3 0GHz 2 H3 H4 H5 H6 option CPU1 Heat Sink Screw holes four screw holes for intel Haswell U Processors Heat Sink assemble 3 FAN1 option 2 54mm Pitch 1x3 Pin Header Fan connector cooling fans can be connected directly for use You may set the rotation condition of cooling fan in menu of BIOS CMOS Setup Pe o SgeNme gt wa Note Output power of cooling fan must be limited under 5W 4 U2 U3 U4 U5 U7 U8 U9 U10 FBGA96 Onboard DDR3L Memory SBC 7110 134010P 4G 4GB SBC 7110 154310P 4G 4GB APC 3X95P R User Manual 18 5 S 422
35. ice Manager Step 5 Click Install to begin the installation P Intel R Network Connections Install Wizard Ready to Install the Program The wizard is ready to begin installation In te y If you want to review or change any of your installation settings dick Back Click Cancel to exit the wizard APC 3X95P R User Manual 52 Step 6 Click Finish to exit the wizard JE Intel R Network Connections Install Wizard Install wizard Completed To access new features open Device Manager and view the properties of the network adapters 4 4 Realtek ALC662 HD Audio Driver To install the Realtek ALC662 HD Audio Driver please follow the steps below Step 1 Select Realtek AL662 HD Audio Driver from the list 4 Drivers CD DRIVERS Intel R CORE TM SoC Chipset Intel R VGA Chipset Intel R 82574L LAN Driver USB 3 0 Driver Touch Panel Driver Intel R AMT Driver OTHERS User Manual APC 3X95P_R User Manual 53 Step 2 Click Next to continue Realtek High Definition Audio Driver Setup 3 65 R2 71 Welcome to the InstallShield Wizard For Realtek High Definition Audio Driver The InstallShield Wizard will install Realtek High Definition Audio Driver on your computer To continue click Next InstallShield N i Cancel Step 3 Click Yes want to restart my computer now Click Finish to complete the installation Realtek High Definition Audio Driver Setup 3 65 R2
36. ies sound duration Cursor Stabilizer Enable the function support to prevent cursor shake Use press and You can set the time out and area for you need hold as right click About This panel displays information about the PenMount controller and driver version AP Device 0 PenMount 6000 USB EIE Calibrate Setting About A PenMount 6000 USB 10 bit LR Driver version 2 1 0 Firmware Version en Firmware Contig Data 6 56064 541 32 7 0 APC 3X95P_R User Manual 11 Multiple Monitors Multiple Monitors support from two to six touch screen displays for one system The PenMount drivers for Windows XP 2003 Vista WIN7 support Multiple Monitors This function supports from two to six touch screen displays for one system Each monitor requires its own PenMount touch screen control board either installed inside the display or in a central unit The PenMount control boards must be connected to the computer COM ports via the USB interface Driver installation procedures are the same as for a single monitor Multiple Monitors support the following modes Windows Extends Monitor Function Matrox DualHead Multi Screen Function nVidia nView Function NOTE The Multiple Monitor function is for use with multiple displays only Do not use this function if you have only one touch screen display Please note once you turn on this function the rotating function is disabled Enable the multiple display function as follows 1 Check
37. l Driver WHOQL V2 4 0 306 in Ehe Following Folder To install in a different Folder click Browse and select another Folder Click Install to start Ehe installation Destination Folder wm Program FilesiPenMounk Windows Universal Dri ert WHOL Space required 0 0KB Space available 13 906 APC 3X95P_R User Manual 63 Step 6 Wait for installation Then click Next to continue PenMount Windows Universal Driver WHQL V2 4 0 306 Setup OF Installing Please wait while PenMount Windows Universal Driver WHOL vz 4 0 306 is being p installed em Execute C Program Files PenMount Windows Universal DriveriwH oL install exe Install Show details Step 7 Click Continue Anyway Hardware Installation A The software vau are installing Far this hardware O PenMount 6000 Serial has not passed windows Logo testing to verify its compatibility with Windows F Tellme why this testing rs important Continuing your installation of this software may impair or destabilize the correct operation of your system either immediately or in the future Microsoft strongly recommends that you stop this installation now and contact the hardware vendor for software that has passed Windows Logo testing Continue Anyway f APC 3X95P_R User Manual 64 Step 8 Click Finish to complete installation PenMount Windows Universal Driver WHQL V2 4 0 306 Setup C Completing the PenMount Windows Universal Driver WHQL Vw 2
38. local environmental regulations Disclaimer This information in this document is subject to change without notice In no event shall Aplex Technology Inc be liable for damages of any kind whether incidental or consequential arising from either the use or misuse of information in this document or in any related materials APC 3X95P R User Manual 2 Packing List Accessories as ticked included in this package are Adaptor Driver amp manual CD disc C Other please specify APC 3X95P R User Manual 3 Safety Precautions Follow the messages below to prevent your systems from damage Avoid your system from static electricity on all occasions Prevent electric shock Don t touch any components of this card when the card is power on Always disconnect power when the system is not in use Disconnect power when you change any hardware devices For instance when you connect a jumper or install any cards a surge of power may damage the electronic components or the whole system APC 3X95P R User Manual Table of Contents Chapter 1 Getting Started LL peat CS oontmde ed ied dn tesi Rt Dp nib tU aded ia conti tredecim omitus d E SOC CHIC GEI Fi Sencdeneaiestcntuesnosetalc tautum c netsturd tuetur aa 1 3 Dimensions v TO ENTERS 1 4 Brief pescripion of APC 3X95P R ee ee EM NE Chapter 2 Hardware 2 1 Mainboard Introduction eee LG 2 2 Specifications bx rema A 2 3 Jum
39. m Enter Select Charge Opt F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save and Exit ESC Exit Administrator Password I mm m Ct ot B e ET User Password b Secure Boot menu Version 2 17 1246 Copyright C 2015 American Megatrends Inc Setup Prompt Timeout 1 Bootup Numlock State APC 3X95P R User Manual 4 On off Quiet Boot Disabled Enabled Fast Boot Disabled Enabled Boot Option Priorities Boot Option 1 Sets the system boot order Hard Drive BBS Priorities SATA PM Boot Option 1 SATA PM K K OK OK K K Disabled 3 8 Save amp Exit Settings Aptio Setup Utility Copyright C 2015 American Megatrends Inc Vain Advanced Chipset Boot Security Save Changes and Exit F4 Save and Exit ESC Exit Version 2 17 1246 Copyright C 2015 American Megatrends Inc APC 3X95P R User Manual Save Changes and Exit Save amp Exit Setup save Configuration and exit Yes No Discard Changes and Ext Exit Without Saving Quit without saving Yes No Save Changes and Reset Save amp reset Save Configuration and reset Yes No Discard Changes and Reset Reset Without Saving Reset without saving Yes No Save Changes Save Setup Values Save configuration Yes No Discard Changes Load Previous Values Load Previous Values Yes No Restore Defaults Load Optimized Defaults Load optimized Defaults Yes
40. nction is disabled if you use the Multiple Monitor function 3 If you change the resolution of display or screen address you have to redo Map Touch Screens so the system understands where the displays are About This panel displays information about the PenMount controller and this driver version PenMount Control Panel m BS Calibrate Draw Multiple Monitors Option About PenMount DMCSODO and DMCS100 Driver Version 4 1 Firmware Version E mail salt salt com tw Website www salt com ty Copyright C 2003 Salt Int l Corp PenMount Monitor Menu Icon The PenMount monitor icon PM appears in the menu bar of Windows XP 2003 Vista WIN7 system when you turn on PenMount Monitor in PenMount Utilities APC 3X95P_R User Manual 80 PenMount Monitor has the following function Control Panel Device Right Button Exit Control Panel Open Control Panel Windows Setting Beep function for each device Right Button When you select this function a mouse icon appears in the right bottom of the screen p Click this icon to switch between Right and Left Button functions Exits the PenMount Monitor function Configuring the Rotate Function 1 Install the rotation software package 2 Choose the rotate function 0 90 180 270 in the 3rd party software The calibration screen appears automatically Touch this point and rotation is mapped Please touch the point e NOTE
41. nd Exit FSC Exit Version 2 17 1246 Copyright C 2015 American Megatrends Inc APC 3X95P_R User Manual 38 3 5 1 PCH IO Configuration Intel PCH RC Version 1 8 0 0 Intel PCH SKU Name Premium SKU Intel PCH Rev ID 04 B2 PCH Express Configuration PCI Express Clock Gating Enabled DMI Link ASPM Control Enabled DMI Link Extended Synch Control Disabled PCle USB Glitch W A Disabled PCIE Root Port Function Swapping Disabled Subtractive Decode Disabled PCI Express Root Port 1 PCI Express Root Port 2 PCI Express Root Port 3 PCI Express Root Port 4 PCI Express Root Port 5 PCI Express Root Port 6 USB Configuration USB Precondition Disabled XHCI Mode XHCI Idle L1 BTCG USB Ports Per Port Disabled Control Disabled Restore AC Power Loss Power off APC 3X95P R User Manual 30 3 6 Boot Settings Aptio Setup Utility Copyright C 2015 American Megatrends Inc Main Advanced Chipset Security Save amp Exit Number of seconds toWait for Setup Prompt Timeout Setup Activation key Boot up Numlock State 65535 0xF FFF means Indef inite waiting Quiet Boot ee a ast DOOL Select Screen f Select Item Enter Select Charge Opt F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save and Exit ESC Exit Version 2 17 1246 Copyright C 2015 American Megatrends Inc 3 6 1 Administrator Password Create New Password me 3 6 2 User Password Create New Pass
42. ng File C Windows system32 difxapi dll Deleting Registry Key HKLM SOFTW ARE Microsoft Windows CurrentVersion Uninstall HDMI Deleting File C ProgramData Microsoft Windows Start Menu Programs Intel Intel R HD Gray Deleting File C ProgramData Microsoft Windows Start Menu Programs Intel R HD Graphics Deleting File C ProgramData Microsoft Windows Start Menu Programs Intel R Graphics and C ProgramData Microsoft Windows Start Menu Programs Intel Intel R Graphic e C Wsers Public Pesktop Vntel R HD Graphics Control Panel Ink C ProgramData Microsoft Windows Start Menu Programs Intel Intel R Iris TM C Users Public Desktop ntel R Iris TM Graphics Control Panel Ink Click Next to continue null am Intel Installation Framework APC 3X95P_R User Manual 49 Step 6 Select Yes want to restart this computer now Then click Finish to complete the installation Intel Graphics Driver Setup Is Complete intel You must restart this computer for the changes to take effect Would you like to restart the 5 No I will restart this computer later Click Finish then remove any installation media from the drives Enh Inkelig Installation Framework 4 3 Intel R LAN Driver To install the Intel R LAN driver please follow the steps below Step 1 Select Intel R 82574L LAN Driver from the list Industrial Panel PG WIN7 DRIVER DRIVERS Intel R CORE TM SoC Chipset Intel R
43. o the computer now Please close the Found Mew Hardware Wizard dialog when it appears Step 9 Click Support Muti Monitor System Click Next eGalaxTouch Setup Type Select the setup type that best suits your needs IF you want to use Mult Monitor please check the box Step 10 Go to C Program Files eGalaxTouch Click Next eGalaxTouch Choose Destination Location Select folder where setup will install Files Setup will install eG alas T ouch in the following Folder To install to this folder click Next To install to a different folder click Browse and select another Falder Destination Folder C Program Fieste ala T auch Cancel APC 3X95P_R User Manual 69 Step 11 Click Next eGalaxTouch Select Program Folder Please select a program folder Setup will add program icons to the Pragram Folder listed below fou may type a new folder name ar select one from the existing folders list Click Nest to continue Program Folder Administrative Tools ames Startup TE Step 12 Click Create a eGalaxTouch Utility shortcut on desktop Click Next eGalaxTouch Setup Type Select the setup type that best suits your needs Select the features you want to install and deselect the features you do nat want to install Click Next to continue APC 3X95P_R User Manual 70 Step 13 Wait for installation eGalaxTouch Setup Status netalls meld Step 14 Click Yes to do 4
44. ocode Patch FSB Speed Max CPU Speed Mix CPU Speed CPU Speed Processor Cores Intel HT Technology Intel HT X Technology Intel SMX Technology 64 bit EIST Technology CPU C3 State CPU C6 State CPU C7 State L1 Date Cache L1 Code Cache L2 Cache L3 Cache Hyper threading Active Processor Cores Overclocking lock Limit CPUID Maximum Execute Disabled Bit Intel Virtualization Technology Hardware Prefetcher Asjacent Cache Line Prefetch CPU AES Boot Performance mode Turbo Performance APC 3X95P R User Manual 40651 6 17 100 MHz 2000 MHz 800 MHz 2400 MHz 2 Supported Supported Supported Supported Supported Supported Supported Supported 32KB x 2 32KB x 2 256KB x 2 3072KB Enabled Enabled All Disabled Enabled Enabled Enabled Enabled Enabled 35 EIST Turbo Mode 3 4 3 SATA Configuration SATA Configuration S SATA Mode Selection SATA Test Mode Aggressive LPM Support SATA Controller Speed Enabled Enabled Enabled Disabled AHCI RAID Disabled Enabled Enabled Disabled Default Gen1 Gen2 Gen3 Software Feature Mask Configuration Serial ATA Port O Software Preserve Serial ATA Port 1 Software Preserve 3 4 4 USB Configuration USB Configuration USB Module Version USB Devices Empty Unknown Empty Unknown 8 10 31 1 Keyboard 1 Mouse 1 Hubs Legacy USB Support APC 3X95P R User Manual
45. ont View of APC 3595P R eeeme eee ll Figure 1 6 Rear View of APC 3595P R eeeeeeme enn ll Figure 1 7 Front View of APC 3795P R eeceee L Figure 1 8 Rear View of APC 3795PJ R cene L2 Figure 1 9 Front View of APC 3995P R eeeene e LO Figure 1 10 Rear View of APC 3995P R ceseeeenee L3 Figure 2 1 Mainboard Dimensions mE RETE EN E o Figure 2 2 Jumpers and Connectors racao oia Top nuns 17 Figure 2 3 Jumpers and Connectors Location Board Bottom ius 17 APC 3X95P R User Manual 6 Chapter 1 Getting Started 1 1 Features Fanless and High Performance Panel PC Intel 4 Core i3 i5 i7 Processor Onboard DDR3 4GB 1333 1600MHz SUS304 Grade Stainless Steel Enclosure SUS 316 Optional Full Flat bezel Design and Totally IP65 IP69K Projective Capacitive Touch Resistive Touch window 9736V DC wide ranging power input 1 2 Specifications D APC 3595P R APC 3795P R APC 3995P R System CPU Intel Core i3 4010U Processor 3M Cache 1 7GHz TDP 15W Intel Core i5 4310U Processor 3M Cache 2 0GHz TDP 15W Chipset SoC Memory Onboard DDR3L 4GB 1333 1600MHz Graphic Integrated Intel HD Graphics 4400 USB 1 x M12 8pin for 1 x USB 3 0 1 x M12 8pin for 2 x USB 2 0 Serial Parallel 1 x M12 8pin for COM1 RS 232 422 485 selectable Default RS 232 1 x M12 8pin for COM2 RS 232 LAN 1 x M12 8pin for LAN Power 1 x M12 3pin DC Power Storage Sp
46. or Stabilization Constant Touch Area Auto Right Click Time APC 3X95P R User Manual 84 Tools Click OK to continue the settings eGalaxTouch USB Controller Liniearizationi Curve e Do 4 points alignment to match display 4 Points Calibration Clear linearization parameter and do 4 points Clear and Calibrate alignment Do 3 paints linearization For better touchscreen linearity Do draw test ta verify the touch accuracy Draw Test e Ao 4 Points Calibration Do 4 points alignment to match display Clear and Calibrate Clear linearization parameter and do 4 points alignment Linearization Do 9 points linearization for better touchscreen linearity Draw Test Do draw test to verify the touch accuracy APC 3X95P_R User Manual 85 Display In this window it shows the mode of display eGalaxTouch USB Controller Display Double click on the monitor area to map the touchscreen to the display monitor W Enable Multiple Monitors Map to main display if sustem has only one display monitor Operation Mode f Ful Screen Lower Screen Lett Screen t Upper Screen Right Screen Other e Enable Multiple Monitors Map to main display if system has only one display monitor Full Screen Lower Screen Left Screen Upper Screen Right Screen APC 3X95P_R User Manual Other C Quarter 3 C Customized C Quarter 2 C Quarter 4 Customized Areas 480 Left fo Right 2
47. pers and C mmetots er E E Patet ly 2 4 Jumpers Setting and E M Chapter 3 BIOS Setup 3 1 Operations after POST Screen eesseeeeeen A 3 2 BIOS Setup D EV sorotna re rna cute Duae Paid esidim Dus M2 9 5 IV OI TS OEIPIB Siete detained m eue inue Lade ee meena 3 4 AdVanted SCUINGS eiiie atu dtd to tutatus testes i ea A 3 5Chipset SOULS S asaan a ducti udo tUm ihi Ia iu eda DOO 3 0 BOOL SOLUTTB Suse coceied tec ior m dio bv et Co ED ein Ear n decuit Ee apr AO 3 7 Security Settings eese eene enne rana rene era ed E 3 0 5dVe EXC Set DS oisein edibus quiso pe aU Oo enu esa Esc du ed AA Chapter 4 Installation of Drivers 4 1 Intel R CORE AMT Driver eee D 4 2 Intel RI VGA CHiPs El i dre ER e o eo A 4 3 Intel R LAN Driver e EB 4 4 Realtek ALC662 HD Audio Driver 4 5 USB 3 0 Driver BS 2 6 Intel RAM DAV Cl s mbH te Depot oe U EO EE CE OO Chapter 5 Touch Screen Installation 5 1 Windows XP 2003 Vista WIN7 Universal Driver Installation for APC 3X95P R User Manual 5 PenMount 6000 Series eeerenn nnne OL 5 2 Software Functions eere nenne nne eee sees 7 2 Figures Figure 1 1 Dimensions of APC 3595P R eeeenene I Figure 1 2 Dimensions of APC 3795P R eeeeen I Figure 1 3 Dimensions of APC 3995P seen LO Figure 1 4 Dimensions of APC 399B5R eee LO Figure 1 5 Fr
48. ting Process regsvr32 exe Creating Process regsvr32 exe Copying File C Windows system32 drivers VntelMEFWVer dll Creating Process C Program Files Intel Intel R Management Engine Components FW Service Deleting File C Program Files Intel Intel R Management Engine Components FWService Inte Copying File C Program Files Intel Intel R Management Engine Components FW Service nte Creating Process C Program Files Intel Intel R Management Engine Components FW Service Deleting File C Program Files Intel Intel R M Management Engine Components FWService Ints Click Next to continue 4 IIT Intel Installation Framework APC 3X95P_R User Manual 59 Step 5 Select Yes want to restart this computer now Then click Finish to complete the installation Intel Management Engine Components Setup Is Complete The setup program successfully installed the following components Intel Management Engine Interface Intel Dynamic Application Loader Intel Identity Protection Technology Intel IPT Local Management Service You must restart this computer for the changes to take effect Would you like to restart the computer now Yes I want to restart this computer now C No I will restart this computer later Click Finish then remove any installation media from the drives Intel Installation Framework APC 3X95P_R User Manual 60 Chapter 5 Touch Screen Installation This c
49. ut connector Switches and LED Indicators 1 x Power on off switch BT1 BT2 CN2 CN3 1 x Reset CN2 APC 3X95P R User Manual 15 1 x HDD LED status CN2 1 x Power LED status CN1 1 x Buzzer External I O port 2 x COM Ports COM1 COM2 2 x USB 3 0 Ports stack 2 x RJ45 GbE LAN Ports 1 x HDMI Port 1 x Stack audio Jack Line out Watchdog Timer Software programmable 1 255 level by Super I O Reserve l Operating 20C to 70 C emperature j Storage 40C to 85 C Humidity 1096 9096 non condensing operating 12V 1 33A Intel 13 4010U processor with 4GB DDR3L DRAM ower E 12V 1 33A Intel 15 4310U processor with 4GB DDR3L DRAM onsumption j 12V 1 33A Intel 17 4510U processor with 4GB DDR3L DRAM EMI EMS Meet CE FCC class A ri I 53 rice B a E E a 7 les exuit RD 2 i RE gg EE S Spon onononoo nooo p m HG amp iE iS ii i J Gy oO 10 00000000000 0000009 Nu E E E L1 Q 9 ann ano00000 o000 ina arene Econ xd E Oooo DOCO tc of O tt FT adl 10 9 ia Co E __ yy T Las poles 9 4 49 NE al 36 16 2 units mm Figure 2 1 Mainboard Dimensions APC 3X95P_R User Manual 16 2 3 Jumpers and Connectors Location 0 17 D e 30 29 21 20 _U10 jooo08 looo ers dod unm Miei ELP e ooo en C E M ES iN E PAN Oye
50. word entes Type the password with up to 20 characters and then press lt Enter key This will clear all previously typed CMOS passwords You will be requested to confirm the password Type the password again and press Enterz key You may press Esc key to abandon password entry operation To clear the password just press Enter key when password input window pops APC 3X95P R User Manual 40 up A confirmation message will be shown on the screen as to whether the password will be disabled You will have direct access to BIOS setup without typing any password after system reboot once the password is disabled Once the password feature is used you will be requested to type the password each time you enter BIOS setup This will prevent unauthorized persons from changing your system configurations Also the feature is capable of requesting users to enter the password prior to system boot to control unauthorized access to your computer Users may enable the feature in Security Option of Advanced BIOS Features If Security Option is set to System you will be requested to enter the password before system boot and when entering BIOS setup if Security Option is set to Setup you will be requested for password for entering BIOS setup 3 7 Security Settings Aptio Setup Utility Copyright C 2015 American Megatrends Inc Main Advanced Chipset Boot Save amp Exit Set Administrator Password Select Screen ft Select Ite
Download Pdf Manuals
Related Search