Home

Dodge/Chrysler

1. UCI 11C into the RGB and Data cables on the Connector 1 harness NOTE These plugs do not have locking tabs It s suggested that you heat shrink over the connection once made or at least wrap tightly with electrical tape 4 Make all of your power connections Red ACC Black GND Yellow CONSTANT 12v You will not use the White wire simply insulate it to avoid any accidental contact These power connections must be made at the cigarette lighter power wires DO NOT make power connections behind the radio or tap into the NAV TV T harness The UCI 11C is very sensitive to current draw and will shut down if you tap into a circuit it is using On most applications the cigarette lighter wires are very easy to get to 5 5 Run your antenna speaker and microphone Please reference the connector diagram on page 5 6 Once all connections are made start system and begin the setup process Installation of the Prodigy Mini Brain 1 Find a suitable place to mount the navigation brain 2 Plug the RGB and Data cables coming from the 11 into the RGB and Data plugs located on the Prodigy Mini brain w Locate the provided 4 pin Intraphex power harness and make all of your power connections Red ACC Black GND Yellow CONSTANT 12v You will not use the White wire simply insulate it to avoid any accidental contact These power connections must be made at the cigarette lighter power wires DO NOT make power connections
2. as you would like 6 Once you are done use the soft exit key to get out of the UCI 11C menu 7 Turn vehicle off shut all doors windows hood and trunk Lock vehicle and wait 3 minutes for the vehicle s CAN system to shut down At this point all settings should have saved 8 Make sure you test all functions before re assembling vehicle M tee 7 Setup for the 8 4 Screen Systems 1 Start vehicle and wait for systems to load completely 2 Press and hold the Power button located in the center of the volume knob for about 5 seconds 3 If you are adding an aftermarket camera first select Camera Input Settings In this menu select Video 2 this is where you should have connected your CVBS camera input previously in the install If the vehicle came with a factory backup camera select Head Unit and if you have no camera at all select Off Once you have found your desired setting click Exit to get back to the main menu gt Enter the Navigation Input Settings menu In this menu you will need to change the Model setting to WP Once you have made this selection you can exit via the soft key D In the same menu you will also see a selection for Timing Leave it at its default setting for the time being 6 Once you are done use the Navigation Settings soft exit key to get out of the 8 UCI 11C menu Navigation On 7 Turn vehicle off shu
3. 4 ZAS EN TD DGE43NAVLAAN TD DGE43NAVI P1 2 TD DGE84NAVI AAN TD DGE84NAVI P1 2 Dodge Chrysler Navigation Installation Manual NAV TV UCI 11C Video GPS Antenna Interface Speaker NAV TV LVDS Cable Microphone NAV TV T Harness Prodigy 1 2 Only NAV TV Camera Input Intraphex Mouse Harness Connector One NAV TV USB Cable Prodigy 1 2 Only Intraphex RGB Data Cable Connector Two Prodigy 1 2 or Mini Navigation Prodigy 1 2 Only Brain WI FI Dongle 8GB SD Card with Intraphex Prodigy 1 2 Only Navigation Software 4 Pin Power Harness Install Users Guides Prodigy Mini Only This manual explains the installation and wiring of the Prodigy Mini and Prodigy 1 2 Systems During the process of your installation please take note to reference the correct wiring diagram that corresponds with the system that you are installing Features such as the microphone and WI FI dongle are specific to the Prodigy 1 2 System DN En A Andu weg uaa OL SAAT 189 SSOUIEH SOM 4101084 5 UONESIAEN Kioyoed 189 Ae sa9 PRODIGY MINI CONNECTIONS RGB SPEAKER GPS CVBS VIDEO DATA SD CARD SLOT UART NOT USED POWER LED STATUS GREEN POWER ON AMBER BOOT SUCESSFUL FLASHING GREEN AMBER GPS S
4. IGNAL AQUIRED O 8 8 PRODIGY 1 2 CONNECTORS B 9 Pin RGB Connector 8 Pin DATA Connector CAUTION When plugging CON 1 into PRODIGY ONE 2 be sure to gently wiggle connector into place to align pins Failure to do so will bend the pins inside prodigy module voiding warranty D Power Connection Yellow 12v Battery Red Ignition Black Ground White Mute output Low AMP must use PRODIGY ONE circuit E Red RCA Right audio line level output F White RCA Left audio line level output G Yellow RCA CVBS Video Output H Stereo speaker level output external speaker 1 Microphone Input NOTE MICROPHONE IS THE THINNER OF THE 3 5MM JACKS SR B UARTA CS UAT CAUTION D Camera video in When plugging CON 2 into PRODILY ON amp 2 be sure to gently E Line in Not Used wiggle connector into place to align pins Failure to do so will bend F ue the pins inside prodigy module voiding warranty e ua IRin out Installation of 11C Video Inte 1 Remove the factory dash of vehicle to gain access to the radio head Pull the radio out enough to gain access to the wiring on the back Unplug the factory white 22 pin connector from behind the radio Install the male end of the supplied NAV TV T hamess into the radio head Plug the factory 22 pin connector into the female e
5. This Limited Warranty gives you specific legal rights and you may have other rights which vary from state to state HY INTRAPIHEN Toll Free Tech Support 888 228 5560 Local 727 803 0324 Email support aampofamerica com
6. behind the radio or tap into the NAV TV T harness The UCI 11C is very sensitive to current draw and will shut down if you tap into a circuit it is using On most applications the cigarette lighter wires are very easy to get to 4 Run your antenna and speaker wires to your desired locations 5 Once all connections are made start the system and begin the startup process Setup for 4 3 Screen Systems 1 Start vehicle and wait for systems to load completely 2 To access the settings screen press and hold the Settings hard key in the upper right corner of the monitor assembly until the menu appears usually about 3 5 seconds w If you are adding an aftermarket camera first select Camera Input Settings In this menu select Video 2 this is where you should have connected your CVBS camera input previously in the install If the vehicle came with a factory backup camera select Head Unit and if you have no camera at all select Off Once you have found your desired setting click Exit to get back to the main menu UCI by NAV TV Camera input settings Navigation input settings About D Enter the Navigation Input Settings menu In this menu you will need to change the Model setting to WP Once you have made this selection you can exit via the soft key 5 From the main Settings menu you may also make adjustments to Brightness Contrast and Saturation
7. cessories or vehicle electrical system Cosmetic damage or damage due to negligence misuse abuse failure to follow operating instructions accidental spills or customer applied cleaners Damage or loss due to environmental causes such as floods airborne fallout chemicals salt windstorms lightning or extreme temperatures Damage or loss due to accidents road hazards fire theft or vandalism Damage due to improper installation or connection improper connection to equipment of another manufacturer modification of existing equipment Product s which have been opened tampered with for any reason or which have been damaged due to alteration or service performed by anyone other than INTRAPHEX EXCEPT AS EXPRESSLY SET FORTH IN THIS LIMITED WARRANTY INTRAPHEX MAKES NO OTHER WARRANTIES EXPRESSED OR IMPLIED INCLUDING ANY IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE INTRAPHEX EXPRESSLY DISCLAIMS ALL WARRANTIES NOT STATED IN THIS LIMITED WARRANTY ANY IMPLIED WARRANTIES THAT MAY BE IMPOSED BY LAW ARE LIMITED TO THE TERMS OF THIS EXPRESSED LIMITED WARRANTY Some states do not allow limitation on how long an implied warranty lasts In such states the limitations or exclusions of this Limited Warranty may not apply Some states do not allow the exclusion or limitation of incidental or consequential damages In such states the exclusion or limitation of this Limited Warranty may not apply to you
8. ep the provided Intraphex mouse You may need to use it one day it will make an excellent addition to the junk drawer of your toolbox 3 Only one USB port will work with the Intraphex mouse If you try one port and it doesn t work simply use the other On the Prodigy 1 2 system there may be a white WIFI dongle installed into the port that works for the mouse In this case simply remove the dongle and replace it after you have finished your setup E INTRAPHEX THREE YEAR LIMITED WARRANTY NONTRANSFERABLE Terms of Limited Warranty INTRAPHEX warrants to the original retail purchaser that the product s purchased from an INTRAPHEX authorized dealer in the original vehicle are free from defects in materials or workmanship under normal use and conditions for a period of THREE 3 years from date of purchase A sales receipt showing the installation date and INTRAPHEX product details are required to verify proof of purchase Should the product s be determined defective during the applicable warranty period the defective product s will be repaired or replaced with a reconditioned product s at INTRAPHEX s sole option To obtain warranty service the product s must be returned to INTRAPHEX authorized installer along with proof of warranty coverage Exclusions Elimination of extemally generated static or noise Costs incurred for installation removal or reinstallation of the product s Damage to any vehicle parts ac
9. nd of the supplied T hamess 2 Route the free end of the T harness behind the radio and up behind the factory screen 3 When you removed the dash there would have been a white round LVDS connector plugged into the back of the dash monitor assembly Take this connector and insert into the white UCI 11C port labeled Radio the provided NAV TV LVDS cable and insert the black end into the UCI 11C port labeled screen Atthis point you should find a suitable place to mount the UCI 11C 5 Plug the free end of the supplied NAV TV T Harness 18 pin into the UCI 11C port labeled radio Plug the supplied LVDS cable that you previously inserted into the black LVDS port on the UCI 11C labeled screen and plug it into the vehicles factory LVDS port behind the monitor 7 If you are using an aftermarket backup camera plug in the 8 pin Molex plug with the RCA s into the UCI 11C NOTE ONLY VIDEO 2 WILL WORK AS A BACKUP CAMERA INPUT The other inputs are currently non functional 8 Locate the Intraphex RGB Data harness Plug the 24 pin end into the UCI 11C s port labeled Navigation 9 Run the RGB Data cable to where you will be mounting the Prodigy brain Installation of the Prodigy 1 2 Brain 1 Find a suitable place to mount the navigation brain FS 2 Plug in the 24 pin Connector 1 Labeled Con 1 to the Prodigy 1 2 brain 3 Connect the RGB and Data cables coming from the
10. prompted to enter a password The password is 7777 then press OK Use the mouse to click the calibration icon You will see a white screen with a crosshair in the center Use your finger to press and release that point Best results are from the driver s side of the vehicle The crosshair will move to four 4 additional locations then press Exit You may now remove the mouse If using the P1 2 system be sure to re install the WIFI dongle into the same port xd 1 To switch into and out of sources use the soft button in the bottom left hand corner of the screen 2 Locate the envelope containing the navigation software SD card and insert it into the Prodigy brain Install the plastic cover two small Phillips screws on the brain to protect the SD card 3 The navigation software will take you through a basic setup It is defaulted for the United States so you can click next through the entire process The final stage of the initial setup may look for a network connection Click Retry Later as this feature is no longer offered All settings can be changed in the Settings menu at a later time if need be 4 Be sure to leave the Navigation Quick Start Guide User s Manual in the vehicle for the End User 1 Be sure to test unit before re assembling the vehicle You don t want to have to go back and Disassemble Reassemble the vehicle 2 After you have finished the installation ke
11. t all Brightness doors windows hood and col trunk Lock vehicle and wait 3 minutes for the vehicle s CAN Model NTX 54 2 system to shut down At this Gia Colors Real point all settings should have saved Timing 1 8 After the CAN system has Bit shut down look at the factory soft buttons at the bottom of the screen If they look like they are cut off go back into the Navigation Settings Menu and change the timing to the other option there are only two of them Exit via the soft exit key and follow steps 6 and 7 9 From the settings menu you may also make adjustments to Brightness Contrast Saturation as you would like Make sure all functions and display are correct before re assembling vehicle IN Calibrating the Screen 1 Start the vehicle and enter the RGB source Prodigy 1 2 Press the soft Navigation key in the bottom right and corner of the screen Prodigy Mini Press and hold the Screen Off key until it switches to the Prodigy HMI NOTE On this system it is usually not necessary to calibrate the touch screen Only go through this process if the touch seems to be off If using the Prodigy 1 2 insert the included Intraphex mouse into the USB port on Connector Two Con 2 Only one port will work You may need to remove the WIFI dongle to get the correct port If using the Prodigy Mini try either port one will work Use the mouse to enter the Settings menu You will be

Dodge/Chrysler

Contents

Download Pdf Manuals

Related Search

Related Contents