Pro-Ject USB Box S+
Contents
1. 10 Da El5 BY PRO JECT AUDIO SYSTEMS INSTRUCTIONS FOR USE Pro Ject USB Box S Dear music lover thank you for purchasing a USB Box S from Pro Ject Audio Systems In order to achieve maximum performance and reliability you should study these instructions for use carefully v Warning of a hazard for the user the unit or possible misuse 15 Important notice Safety instructions AC outlet voltages vary from country to country Before connecting to the mains make sure that the voltage in your area meets the voltage requirements printed on the power supply The power supply is used to disconnect the unit from the mains Make sure that the power supply is easily V accessible at all times Never handle the device the power supply while your hands are wet or damp Avoid letting liquids enter the device or the power supply Never place any item containing liquid such as a flower vase on or near the device Never spill any liquid on the device or the power supply Never place any naked flame sources such as lighted candles on or near the device The product shall not be used in damp or wet locations next to a bathtub sink swimming pool or any other similar conditions Connectors Out Left Right A Y CE mus A Pro Ject Audio Systems Vienna Austria Make all connections except the connection to the computer whilst the unit is disconnected from the power supply Connect the unit to the mains and switch it on before c2. SB input USB B socket USB cable supplied USB signal digital serial data protocol USB 2 0 Dimensions W x H x D D with sockets 103 x 36 x 104 109 mm Weight 576g Pro Ject Audio Systems gt Pro Ject USB Box S Revision 2014 3 31 3 Service Should you encounter a problem which you are not able to alleviate or identify despite the above information please contact your dealer for further advice Only if the problem cannot be resolved there the unit should be sent to the responsible distributor in your country Warranty The manufacturer accepts no responsibility for damage caused by not adhering to these instructions 15 for use Modification or changes to any part of the product by unauthorized persons release the manufacturer from any liability over and above the lawful rights of the customer Copyright trademarks Pro Ject Audio Systems is a registered Trademark of H The information was correct at the time of going to Lichtenegger press The manufacturer reserves the right to make This guide was produced by Pro Ject Audio Systems changes to the technical specification without prior Copyright 2014 All rights reserved notice as deemed necessary to uphold the ongoing process of technical development Windows XP Windows Vista Windows 7 and Windows 8 are trademarks of the Microsoft group of companies Mac and Mac OS are trademarks of Apple Inc registered in the U S and other countries Dolby is a regist
3. ered trademark of Dolby Laboratories DTS is a registered trademark of DTS Inc 4 Pro Ject Audio Systems Pro Ject USB Box S Revision 2014 3 31
4. onnecting it to the computer y Take care to connect the left and right channels correctly The right channel is usually marked red the left channel black or white Never use any other power supply than the one supplied with the unit Mains power connection Connect the low voltage plug from the power supply to the Power 9V DC socket before connecting the power supply to the mains Connection to the amplifier Connect the Left Right Out socket to a line input such as AUX on your amplifier Connecting to a computer Connect the USB input to a free USB socket on your computer and turn it on make sure it is powered on The DAC will be automatically recognised by the computer For Windows operating systems a 24Bit 192kHz driver supplied on CD has to be installed Mac OS operating systems support 24Bit 192kHz as a standard Please note Connection should be made to an USB socket of your computer directly Connecting to USB hubs or switches can cause problems 2 Pro Ject Audio Systems gt Pro Ject USB Box S Revision 2014 3 31 24Bit 192kHz driver Windows operating systems only For Windows operating systems a Pro Ject USB Audio driver has to be installed Insert the included CD into the drive of your PC and follow the instructions After installing the driver some settings have to be done For example Windows 8 operating system gt Control Panel gt Hardware and Sound gt Sound gt Playback select Projec
5. t USB Box S USB 2 0 Audio Out gt Properties gt Supported Formats make sure nothing is assigned gt Level gt Sound setting must be 100 gt Enhancements disable all enhancements gt Advanced gt Default Format set to studio quality 24 192 Windows OS does not support more than 24bits 192kHz Pro Ject USB Box S supports up to 32bits 384kHz For playing such audio files a proper player software has to be installed on your computer e g Foobar2000 JRiver Mediacenter and additionally the Project Box ASIO driver has to be selected as an output audio device Front panel and controls i Filter o 44 1 88 2 176 352 8 a 4 USB Box S AS d To switch on from standby or to standby The push button on the left hand side of the front panel turns the unit on or back into standby The blue LED above the stand by push button shows that the unit is switched on Filter Filter will toggle between the two filters available The blue LED is illuminated when second filter is selected Sampling frequency LED indicators On the front panel are 8 LEDs which indicate current sampling frequency of the incoming digital signal Technical specifications Pro Ject USB Box S Line level output 1 pair RCA phono sockets Output voltage 2 1Vrms D A converter Burr Brown PCM5102 32 Bit Delta Sigma Supported audio format PCM LPCM No support for formats like Dolby Digital or DTS Sampling rate 44 1 48 88 2 96 176 192 352 8 384kHz U
Download Pdf Manuals
Related Search