User Manual (4) Enclosure Assembly (5) System Set Up (1
Contents
1. 2 Detailed View LED indicator OFF Power OFF Solid Blue Power ON status ready Flashing Blue Power ON read write access 3 Hard Drive Assembly a Remove the 4 screws located at the bottom of the case and pull out the circuit board from the enclosure iK se JC STORAGE ENCLOSURE 1 Specifications Application 2 5 SATA I or SATA II hard drive e 20GB 1TB e 9 5mm or 12 5mm Interface Ports USB 3 0 Super Speed backwards compatible with USB 2 0 Data Transfer Rate USB 3 0 up to 5Gbps 625MB s pa akh 93 z e USB 2 0 up to 480Mbps 60MB s PI E E erie i e USB 1 1 up to 12Mbps 1 5MB s E Be ee WT Tn LE System Requirements PC Windows XP Vista 7 e Mac Mac OS 10 2 or above e Your hardware device must have the correct corresponding port e g USB 3 0 USB 2 0 or PCI card a b Install the hard drive and mount it with the two screws ha from the bottom through the circuit board and with the Operating Environment Temperature 5 C 40 C p g P n two screws from the side e Humidity 10 RH 80 RH User Manual March 17 2010 v1 0 FE CE Storage Environment Temperature 20 C 70 C e Humidity 5 RH 90 RH Power Supply optional Input AC 100 240V 0 6A 50 60Hz e Output DC 5V 2A Enclosure Size 12 5cm x 7 8cm x 2 4cm Power receptacle Note Your unit may come with a pre installed h2. ard drive Before opening your enclosure please read the warranty carefully as this could void it For more information visit our website at www inxtron com USB 3 0 was not available for Mac OS at the time this manual was written 4 Enclosure Assembly 5 System Set Up 6 Safety Information 7 FAQ a Slide the assembled drive back into the enclosure but be careful not to damage any of the components b Fasten the 4 screws at the bottom of the casing to finish the assembly Next peel off the paper from the back of the self adhesive rubber feet Now place the rubber feet over the screws and stick them on the casing to cover the Screws Note Be careful not to damage any components when installing the HDD If the drive has been pre installed and setup already you do not need to prepare anything else and can use it straight out of the box If you have installed the drive yourself and this is a brand new HDD you will have to create a partition first and format the drive before it is recognized by the computer a Turn on your computer and start the system b Connect the SK 2500 to your computer If bus power is insufficient you will have to use the external power supply c The system will automatically mount the drive PC users can access it under My Computer and Mac users on the desktop d If the drive does not show up make sure it has sufficient power Then for PC users use the Disk Management tool o
3. e cord e Do not touch the power cable with wet hands e Never try to repair or modify the power cable yourself e If the unit should emit smoke an unusual odour or noise disconnect it immediately and unplug the power cable Cables Use only the cables supplied or recommended by your vendor in order to avoid any sort of malfunction Q What file system should I use to format the drive A This will depend on how you want to use the drive but in general we recommend e Windows XP Vista 7 gt NTFS e Mac OS X gt HFS Mac OS Extended e To use it on both PC and Mac gt FAT32 Q Can I use my device with bus power only A This will depend on the hard drive the interface cable and the host computer In general bus power for USB 3 0 is sufficient and there is no need for an extra power supply If it is insufficient e g USB 2 0 an external power supply is required or we recommend using a hard drive with lower power consumption a shorter cable avoid using any kind of extensions or unpowered USB hubs and making sure the host provides enough bus power Q Can I connect it to a USB 2 0 host A Yes this device is backwards compatible with USB 2 0 2010 by inXtron Inc All Rights Reserved The information contained in this document is believed to be accurate and reliable inXtron assumes no responsibility for any errors or differences between the product you may have and the one mentioned in this document and reserve
4. r for Mac users the Disk Utility to prepare and format the drive Be aware that formatting the drive will erase all existing data e For the safe removal of your drive and to assure that no data is lost always eject the external drive from your system first before you disconnect it Note When not in use for longer periods of time it is recommended to disconnect the device and remove the power supply from the wall socket a a a eh i tes at iy he ih mt Ga a tym ems ur Fa Gy RS many i my i m uh i ms itr Fi il um a upset sh lh humm ic uy my i ll ejay tm ity ii mh ip mid ist ui ms mas i ty per ily uma Gp i itr T s iy my uh ih us ym a Es iy uh Gt my i a Sa tty Location and placing precautions Do not cover the SK 2500 and do not place the unit on other heat sensitive equipment Avoid positioning it in the following places e Locations with direct sunlight next to radiators or other sources of heat with high temperatures more than 35 C or high humidity more than 90 e Locations subject to vibration shock or with a slope e Do not expose the product to water or humid conditions Electricity and power plug Careful attention must be paid to the following points in order to avoid operational faults and electric shock or fire e Always connect the power adapter to your device before you plug it into the wall socket e When removing the power cable from the socket always pull on the plug fixture and never on th
5. s the right to make changes in the specifications and or design of this product without prior notice The diagrams contained in this document are for reference and may not fully represent the real product
Download Pdf Manuals
Related Search