Quick Guide
Contents
1. figure gives you an overview of the cable installation Power The scanner requires a minimum of 450mA at 9V DC power and the use of external power is usually Pre recommended It turns on when power terminal g is supplied and turns off when power is removed There is no on off switch on the scanner itself optional auxiliary scanner Cable Replacement Mounting Plate Installation The interface cable comes with When installing the host cable to the mounting plate different host end connectors and the please insert the flat side of the cable bracket in the cable is attached to the scanner witha cable release hole first as shown in illustration 10 pin modular connector When properly seated the scanner is secured in the scanner bottom by a flexible retention tab The cable is designed to be field replaceable Replacement cables can be obtained from your authorized distributor Tone and Volume Adjustment The tone and volume can be changed by using the touch control sensors in the front There are three tones levels of volumes to choose from Gently touch the sensor and the scanner would change to its next tone volume level Repeat touching till the desired sound is heard However the volume setting is saved in volatile memory That means the change will lost when the scanner powers down On next power up the scanner would reset to the configured setting If you wish to keep the changed volume setting use the Programmin2. Enter Exit Programming Mode Display firmware version Scan this barcode to enter the set up and exit Show the current firmware version on the host after set up is finished The LED would remain screen red when in programming mode HUSeee ese eee see ee see esses e see esses seee es essen Folding Line 42 222222224422 ses5ssseeseesssssd se deeeae l Return to PC AT default Return to RS 232 default This barcode allows setting as keyboard The RS 232C interface scanner is often used wedge interface for IBM PC AT PS 2 and when connecting to the serial port of a PC or compatibles terminal 3 Se Sa nc er ee Folding LING lt 2 Return to USB default Reset Return to Factory Default Reading of Return to USB default sets the Reading of Reset barcode label turns all device into USB interface support parameters back to default values and the scanner remains in the last interface set when it is reset EE E E E E eee Folding Lin lt ass EE l Since the scanner has a large scan volume and multiple scan lines it is suggested to fold this page according to the dotted line so you can easily present the desired barcode to the scanner The scanner must be properly powered before programming It would acknowledge a good and f Important Notice valid reading with a short beep No warranty of any kind is made in regard to this material including but not limi
3. g Guide to set and save the changes Verifying Scanner Operation Before mounting your scanner please follow the procedure below to verify scanning operation 1 Take a stick to poke in the hole on the back of the scanner to remove the mounting plate 2 Insert the interface cable into the Host connector at the back of the scanner until a firm click is heard Put the mounting plate back optional Plug the other end of the cable to the host Plug the power adapter into the jack on the interface cable Plug the AC end of the power adapter into an AC outlet The scanner powers up the speaker sounds four beeps and the LED indicator glows blue Present a known good test barcode to the scanner The scanner should issue a short beep and the LED should flash red once The scanner should read one barcode beep and the LED remain red if it is connected to a keyboard wedge but not connected to a live host terminal The LED would flash red and read no barcode if the scanner is programmed in USB interface but not connected to a host device LED Indications Sound Indications There are red and blue dual color LED The device uses a speaker to give audio indications on the head of the device indicating feedback on scanner operation The following the operational status of the scanner are the sound indications LED Status Indication Beeps Indication LED off No power supplied to the One beep A barcode has been scanner successfull
4. ted to implied warranties of merchantability or fitness for a particular purpose We are not liable for any errors contained herein or incidental or consequential damages in connection with furnishing For more set up selections please refer to Programming Guide in the CD ROM in the Ee Gnglleea ene a C ous e ea ackage p g Laser Safety a a ngs iG QS a a Tt a ca a eR eas The laser scanner complies with safety standard IEC 60825 1 for a Class laser produce It also complies with CDRH as applicable to a Class lla laser product Avoid long term staring into direct laser light Ver 1 1 P N 593 66182E 201 CAUTION Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure Introduction This Quick Guide applies to the Advanced Compact Dual Laser Omnidirectional Vertical Scanner Detailed information about installation troubleshooting and configuration can be found in the User s Manual and Programming Guide in the CD ROM We reserve the right to make changes to improve reliability function or design For the latest revision of the manual please contact your distributor Unpacking The scanner package may be altered upon customer request but it usually contains 1 ea scanner 1 ea Interface cable 1 ea 9V power adaptor and 1 ea manual in CD ROM or hard copy Installation The scanner is to be connected to a host e g POS This
5. y decoded Steady blue light The scanner is powered Two beeps low high The scanner has entered on and ready to scan programming mode One red flash A barcode has been Two beeps of the ee dienes successfully decoded same tone prog g normal mode prog g This indicates the Flashing blue light Li ea eee Four beeps in series scanner passed self test continuous tone when powered on and is The scanner has a motor or laser failure Return the unit for repair Steady red blue Operating properly light The scanner is programmed in USB This is a failure Flashing red light interface but not Continuous tone indication connected to a host Return the unit for repair device
Download Pdf Manuals
Related Search