Digital Video Recorder Quick Operation Guide
Contents
1. HIKVISION Digital Video Recorder Quick Operation Guide UD 6L0202B0063A01 Quick Operation Guide of Digital Video Recorder Thank you for purchasing our product If there is any question or request please do not hesitate to contact dealer This manual is applicable to DS 7204HFHI ST DS 7208HFHI ST DS 7204HFHI SE and DS 7208HFHI SE DVR DVR Pre Installation The DS 7200HFHI ST amp SE DVR is highly advanced surveillance equipment that should be installed carefully Please take into consideration the following precautionary steps before installation of the DVR 1 Keep all liquids away from the DVR 2 Install the DVR in a well ventilated and dust free area 3 Ensure environmental conditions meet factory specifications 4 Install a manufacturer recommended HDD DVR Installation During the installation of the DVR Use brackets for rack mounting Ensure there is ample room for audio and video cables When installing cables ensure that the bend radius of the cables are no less than five times than its diameter Connect both the alarm and RS 485 cable Allow at least 2cm 0 75 inch of space between racks mounted devices Ensure the DVR is grounded Environmental temperature should be within the range of 10 C 55 C 14 F 131 F Environmental humidity should be within the range of 10 90 Hard Disk Installation Before you start SNNAM FW N Before installing a hard disk drive HDD p2. Recording manual record schedule record motion detection or alarm triggered record Alarm amp Recording Record Settings Before you start Make sure that the HDD has already been installed If not please install a HDD and initialize it You may refer to the user manual for detailed information Purpose Two kinds of record types are introduced in the following section including Instant Record and All day Record And for other record types you may refer to the user manual for detailed information Note After rebooting all the manual records enabled are canceled Instant Record Option 1 On the live view window of each channel there is a quick setting toolbar which shows on the bottom of the window when you click on it OR SN Woe Click the icon to enable the record and the icon turns to And click icon to disable the record then the icon turns to g 17 Quick Operation Guide of Digital Video Recorder Option 2 Steps 1 Enter the Manual settings interface Menu gt Manual Analog Recording by schedule Recording by manual operation 2 Enable manual record Click the status icon OFF before camera number to change it to ON Or click the status icon OFF of Analog to enable manual record of all channels 3 Disable manual record Click the status icon cI to change it to OFF Or click the status icon ON of Analog to disable manual record of all channels All day Record Perform the
3. 112 192 168 112 192 168 14 192 168 1 12 192 188 112 192 168 1 12 192 168 1 12 192 168 1 12 192 168 1 12 192 168 14 192 168 1 12 192 168 11 192 168 112 192 168 11 192 168 1 12 192 168 1 42 192 168 112 192 168 14 192 168 112 192 168 112 192 168 1 42 Search Log Major Type All Types v Minor Type All Types v Start Time 2013 02 28 00 00 00 End Time 2013 02 28 23 59 59 Q Search Ej Save Log 2 Set the log search conditions to refine your search including the Major Type Minor Type Start Time and End Time 3 Click the Search button to start searching log files 4 The matched log files will be displayed on the list shown below Note Up to 100 log files can be displayed each time You can click the ied Save Log 15 button to save the searched log files to local directory Quick Operation Guide of Digital Video Recorder Menu Operation Menu Structure The menu structure of the DVR is shown below Menu gt _ Playback Export Manual HDD _ Record Camera Configuration Maintenance Shutdown Coe CONSE as Normal Normal Record General Schedule OSD General System Info Logout eee Log i m Event Event Advanced Encoding PrE Network Informaion Shutdown Tag HDD Detect Advanced Motion Live View Import Export Reboot Holiday oe Exceptions _ Upgrade Tamper proof User Default Video Lass Ne
4. following steps to set the all day recording Option 1 On the live view window right lick the window and move the cursor to the Start Recording option and select Normal Record or Motion Detection Record on your demand Menu Single Screen Multi screen Previous Screen Next Screen Start Auto switch Normal Record Quick Set Motion Detection Record All day Playback And click the Yes button in the popup Attention message box to confirm the settings Then all the channels will start to record in the selected mode Option 2 Steps 1 Enter the Manual settings interface Menu gt Manual Analog Recording by schedule Recording by manual operation 2 Click the M icon of corresponding record types to set all day record of that type Normal and Motion Detection are selectable 18 Quick Operation Guide of Digital Video Recorder 3 And click the Yes button in the popup Attention message box to confirm the settings Playback Play back the record files of a specific channel in the live view menu Instant playback by channel Choose a channel under live view using the mouse and click the button in the shortcut operation menu Note Only record files recorded during the last five minutes on this channel will be played back All day Playback by channel 1 Enter the All day Playback menu Mouse right click a channel in live view mode and select All day Playback from the menu Menu Si
5. 2 9 38 38 2013 02 28 09 38 39 Log Major Type Operation Operator Operation Iperator Operation Operator Operation Ope orn Opera on peraton Operation Operator Operaton Operator Operation Iperavor Operaton peras on Opera on pera on Operaton peraton Operation peradon Operaton peradon Operaton perator Operation perasor Configuration Minor Type Remote Get Parameters Remote Get Parameters Remote Get Parameters Remote Get Parameters Remote Get Parameters Remote Get Parameters Remote Get Parameters Remote Parameters Remote Get Parameters Remote Get Parameters Remote Configure Parameters Remote Configure Parameters Remote Configure Parameters Remote Get Parameters Remote Get Parameters Remote Get Parameters Remote Get Parameters Remote Get Parameters Remote Get Parameters Remote Get Parameters Remote Get Pararneters Remote Configure Parameters Remote Configure Parameters Remote Configure Parameters Remote Get Parameters Remote Get Parameters Remote Get Parameters Remote Get Pararneters Remote Get Parameters Remote Get Pararneter Channel No at A3 Total 231 tems FirstPage Prev Page 1 3 Nart Page LastPage Local Remote User admin admir admin admir admin admir admin admir admin admin admin Remote Host IP 192 168 112 192 168 1 12 192 168 1 12 192 168 1 12 192 168 1 12 192 168 1 12 192 168 1 12 192 168
6. 8 connection TCP IP PPPoE DHCP DNS DDNS NTP SADP SMTP SNMP NFS iSCSI UPnP SATA 1 SATA interface 2 SATA interfaces Network protocols Consumption without hard Max 15 W Max 20 W disk Working 10 C 55 C 14 F 131 F temperature Working humidity 10 90 19 inch rack mounted 1U Chassis Stand alone 1U chassis chassis Dimensions 315x230x45 mm 445x290x45mm W x Dx H 12 3x9 0x1 8 inch 17 3x11 3x1 8 inch Weight without hard 2 kg 4 4lb 4 kg 8 81b disks Quick Operation Guide of Digital Video Recorder HDD Storage Calculation Chart The following chart shows an estimation of storage space used based on recording at one channel for an hour at a fixed bit rate Note Please note that supplied values for storage space used are just for reference Storage space used is estimated by formulas and may have some deviation from actual value 10 Quick Operation Guide of Digital Video Recorder Accessing by Web Browser Logging In You can get access to the device via web browser Open web browser input the IP address of the device and then press Enter The login interface appears Note You may use one of the following listed web browsers Internet Explorer 6 0 Internet Explorer 7 0 Internet Explorer 8 0 Internet Explorer 9 0 Internet Explorer 10 0 Apple Safari Mozilla Firefox and Google Chrome Note The supported resolutions include 1024 768 and above Note The defaul
7. Displays the time bar and the records marked with different colors Playback Status Displays the playback status including channel number and playback speed Calendar You can select the date to play Start Playback Steps 1 Click Playback on the menu bar to enter playback interface 2 Click the camera from the device list for playback 3 Select the date from the calendar and click Search 4 Click the Play button to play the video file searched on the current date Use the buttons on the toolbar to operate in playback mode 5 Video clip a2 Open Close audio You can drag the progress bar with the mouse to locate the exact playback point You can also input the time in the textbox i and click button to locate the playback point The color of the video on the progress bar stands for the different video types E command M Schedule Recording BAlarm Recording O Manual Recording 14 Quick Operation Guide of Digital Video Recorder Log You can view and export the log files at any time including operation alarm exception and information of device Before you start The Log function can be realized only when the device is connected with HDD or network disk And make sure the HDD or network disk has been initialized for the first time to use Steps 1 Click Log on the menu bar to enter the Log interface ad Ld 9 9 ra O iw amp w amp 2013 02 28 09 38 38 2013 0
8. P Quick Operation Guide of Digital Video Recorder USB port 2 x USB2 0 Alarm in out 4 1 optional Power supply 12V DC Consumption without hard Max 15 W Max 20 W disks Working 10 C 55 C 14 F 131 F temperature Working humidity 10 90 19 inch rack mounted 1U chassis Dimensions 445 x 290 x 45 mm 17 5 x 11 4 x 1 8 inch WxDxH Table 2 Specification for DS 7200HFHI SE o STOS DS 7208HFHLSE HD SDI video sch input HD SDI interface 800 mVp p 75 Q Supported HD SDI camera 1080160 1080150 1080P30 1080P25 720P60 720P50 720P30 720P25 types Audio G 71lu compression Audio input RCA 2 0 Vp p 1 KQ 1 ch RCA 2 0 Vp p 1 KQ using the 1 channel of audio Two way audioin input HDMI VGA 1920 x 1080 60 Hz 1280 x 1024 60 Hz 1280 x 720 60 Hz output 1024 x 768 60 Hz Encoding Main stream 1080P 12fps 720P VGA 4CIF CIF resolution Sub stream 4CIF non real time CIF QCIF QVGA Main stream 1 16 fps Real time frame rate Frame rate Sub stream 1 16 fps Real time frame rate Video bitrate 32 Kbps 16 Mbps Audio output 1 ch RCA Linear 1KQ Stream type Video Video amp Audio Quick Operation Guide of Digital Video Recorder Synchronous 4 ch 8 ch playback up to 2 ch 720P real time up to 2 ch 720P real time Playback 1080P 720P VGA 4CIF CIF QVGA QCIF resolution Output bandwidth 128Mbps Remote 12
9. e view B oe SEN 3 You can click the SG button on the toolbar to start the live view of all cameras on the device list Refer to the following table for the description of buttons on the live view window Select the window division mode Previous page Recording Before you start Make sure the device is connected with HDD or network disk and the HDD or network disk has been initialized for the first time to use Two recording types can be configured Manual and Scheduled The following section introduces the configuration of scheduled recording Steps 1 Click Remote Configuration gt Camera Settings gt Record Schedule to enter Record Schedule settings interface 2 Select the camera to configure the record schedule 3 Check the checkbox of Enable Schedule to enable recording schedule 12 Quick Operation Guide of Digital Video Recorder Schedule Settings Channel No Analog Camera v Record Enable Record Schedule Edit Advanced E Normal E Motion Detection Alarm E Motion Alarm Motion amp Alarm Copy to Camera C Select All A1 Oa C3 Om Oas Cie Save a7 4 Choose the day in a week to configure scheduled recording 5 Click Edit to edit record schedule Edit Schedule Mon OAll Day i Customize Period 4 on A UN Copy to Week Select All Start Time 00 00 00 00 00 00 00 00 00 00 00 00 00 J S all EEE Mon T
10. into terminal block Note The RS 485 unit can be used as T and T when it s working in the output mode and R and R when it s working in the input mode We take the RS 485 connection of DS 7204HFHI SE as an example Quick Operation Guide of Digital Video Recorder Specifications Table 1 Specification for DS 7204HFHI ST Se DS 7204HFHL ST DS 7208HFHL ST me HD SDI video sch HD SDI interface 800 mVp p 75 Q 1080160 1080150 1080P30 1080P25 720P60 720P50 720P30 720P25 input Supported HD SDI camera types Audio compression Audio input RCA 2 0 Vp p 1 KQ 1 ch RCA 2 0 Vp p 1 KQ using the 1 channel of audio Two way audioin input HDMI VGA 1920 x 1080 60 Hz 1280 x 1024 60 Hz 1280 x 720 60 Hz output 1024 x 768 60 Hz Encoding Main stream 1080P 720P VGA 4CIF CIF resolution Sub stream 4CIF non real time CIF QCIF QVGA Main stream 1 16 fps Real time frame rate Frame rate Sub stream 1 16 fps Real time frame rate Video bitrate 32 Kbps 16 Mbps Audio output 1 ch RCA Linear 1KQ Stream type Video Video amp Audio Synchronous 4 ch 8 ch playback up to 2 ch 1080P real time up to 2 ch 1080P real time Playback 1080P 720P VGA 4CIF CIF QVGA QCIF resolution Output bandwidth 128Mbps Remote 128 connection TCP IP PPPoE DHCP DNS DDNS NTP SADP SMTP Network protocols SNMP NFS iSCSI UPn
11. lease make sure the power is disconnected from the DVR A factory recommended HDD should be used for this installation For the HDD installation steps between DS 7200HFHI ST amp SE devices are similar here we take the steps of DS 7204HFHI ST as example Up to 2 SATA hard disks can be installed on your DVR Tools Required Screwdriver Steps for DS 7200HFHI ST amp SE 1 Remove the cover from the DVR by unfastening the screws on the back and side 2 Connect one end of the data cable to the motherboard of DVR and the other end to the HDD Quick Operation Guide of Digital Video Recorder 3 4 Place the HDD on the bottom of the device and then fasten the screws on the bottom to fix the HDD e b z o e D 5 e e e 2 e oo a E e 2 al bad oe Re install the cover of the DVR and fasten screws Quick Operation Guide of Digital Video Recorder Front Panels 2 3 4 5 Front Panel of DS 7200HFHI ST Description of Control Panel Buttons No Function Description POWER Power indicator turns yellow once the power switch turns on READY Ready indicator turns yellow when system is running STATUS Status indicator turns red when SHIFT mode is on 1 ALARM Alarm indicator turns red when a sensor alarm is detected HDD indicator blinks red when data is being read from or written to HDD TX RX indictor blinks yellow when network connection is TX RX o functioning properly Universal Serial Bus USB ports f
12. nce the video by a single frame In Auto switch mode it can be used to stop start auto switch HIK VISION l 2 3 Front Panel of DS 7200HFHI SE Description of Front Panel Function Description Power indicator turns yellow when the power switch on the real panel is turned on Status indicator blinks red when data is being read from or written to 1 STATUS HDD TX RX indictor blinks yellow when network connection is functioning TX RX properly i Universal Serial Bus USB ports for additional devices such as USB 3 B Int M AE mouse and USB Hard Disk Drive HDD Quick Operation Guide of Digital Video Recorder Rear Panels DS 7208HFHI ST amp SE Item HD SDI interface for video input 4 VGA DB9 connector for VGA output Display local video output and menu 6 USBPort Universal Serial Bus USB port for additional devices 8 RS 485 Interface Connector for RS 485 devices 9 Power Supply DC 12V power supply S Power Switch Switch for turning on off the device Quick Operation Guide of Digital Video Recorder Peripheral Connections RS 485 Connection Rear Panel of DS 7204HFHI SE A B amp RS 485 To connect RS 485 devices to the DVR 1 Disconnect pluggable block from the RS 485 terminal block 2 Press and hold the orange part of the pluggable block insert signal cables into slots and release the orange part Ensure signal cables are in tight 3 Connect pluggable block back
13. ngle Screen Multi screen Previous Screen Next Screen Start Auto switch Start Recording Quick Set All day Playback Front Panel press PLAY button to play back record files of the channel under single screen live view Under multi screen live view record files of the top left channel not masked will be played back Note pressing numerical buttons will switch playback to related channels during playback process 2 Playback management The toolbar in the bottom part of Playback interface can be used to control playing process 19 Quick Operation Guide of Digital Video Recorder The channel and time selection menu will display by moving the mouse to the right of the playback interface Just tick the channel or channels if you want to switch playback to another channel or execute simultaneous playback of multiple channels Al chy Play tom kk AMATA I7 CECIL EES amera H ma yY E A A 1 14 4 145 6 17 16 t3 20217 22 25 M 25 25 27 28 23 30 Backup Recorded files can be backed up to various devices such as USB flash drives USB HDDs or USB DVD writers To export recorded files 1 Enter Video Export interface Choose the channel s you want to back up and click the Quick Export button iY Analog MA2 MA3 MAA 2011 08 31 11 10 23 2012 11 13 08 58 53 All All 2012 11 13 2012 11 13 00 00 00 23 59 59 2 Enter Export interface choose backup device and click the Export button to start expor
14. or additional devices such as er eae USB mouse and USB Hard Disk Drive HDD Switch between the numeric or letter input and functions of the composite keys Input letter or numbers when the light is out Realize functions when the light is red Enter numeral 1 1 MENU Access the main menu interface Enter letters ABC The F1 button when used in a list field will select all items in the 2 ABC F1 list In PTZ Control mode it will turn on off PTZ light and when the image is zoomed in the key is used to zoom out i Enter letters DEF Composite 3 DEF F2 4 GHUESC Keys S JKL EDIT 6 MNO PLAY Enter letters MNO Playback for direct access to all day playback interface Quick Operation Guide of Digital Video Recorder TIPQRSIREC 8 TUV PTZ 9IWXYZ PREV Enter numeral 0 o Enter numeral 0 0 A Shift the input methods in the editing text field Upper and lowercase alphabet symbols or numeric input The DIRECTION buttons are used to navigate between different fields and items in menus In the Playback mode the Up and Down button is used to speed up and slow down recorded video The Left and Right button will select DIRECTION the next and previous record files channels camera modes It can also be used to tick checkbox fields In Playback mode it can be used to play or pause the video In single frame Playback mode pressing the button will adva
15. t Detect Startup and Shutdown Proper startup and shutdown procedures are crucial to expand the service time of the DVR To start the DVR Check the power supply is plugged into an electrical outlet It is HIGHLY recommended that an Uninterruptible Power Supply UPS be used in conjunction with the device Turn on the power switch on the rear panel the Power indicator LED on the front panel should be yellow To shut down the DVR 1 Enter the Shutdown menu Menu gt Shutdown Shutdown i Logout Shutdown Reboot 2 Select the Shutdown button 3 Click the Yes button 4 Turn off the power switch on the rear panel when the note appears for DS 7200HFHI SE series only 16 Quick Operation Guide of Digital Video Recorder Please power off After the device starting up the wizard will guide you through the initial settings including modifying password date and time settings network settings HDD initializing and recording Live View Some icons are provided on screen in Live View mode to indicate different camera status These icons include Live View Icons In the live view mode there are icons at the right top of the screen for each channel showing the status of the record and alarm in the channel so that you can find problems as soon as possible Indicating that there is an alarm or are alarms Alarm includes video loss tampering motion detection or sensor alarm etc lt E rE
16. t IP address is 192 0 0 64 ET User Name EN b v RB Password Input the user name and password and click the Login button Note The default user name is admin and password is 12345 When you log in for the first time the system will remind you to install the Plug in control After the installation you can configure and manage the device remotely Live View The live view interface appears by default when you log in the device _uveview Ear Log Configuration admen Logout Embedded NetovR Camera 01 Camera 02 A Camera 03 A Camara 04 Camera 05 G Camera 06 Camera 07 Camera 08 Interface Introduction 1 Channel List Displays the list of channels and the playing and recording status of each channel 2 Live View Window Displays the image of channel and multi window division is supported 3 Play Control Bar Play control operations are supported 4 PTZ Control Pan tilt zoom operations are supported as well as preset editing and calling Note PTZ function can only be realized if the connected camera supports PTZ control Video Parameters Configuration Brightness contrast saturation and hue of the image can be modified Start Live View Steps 11 Quick Operation Guide of Digital Video Recorder 1 Inthe live view window select a playing window by clicking the mouse 2 Double click a camera from the device list to start the liv
17. ting 20 Quick Operation Guide of Digital Video Recorder USB1 1 Refresh 2 004MB New F older Format Cancel 3 Check backup result Choose the record file in Export interface and click button to check it USB1 1 Refresh B B amp B player exe 538KB File 04 26 2012 16 47 06 O 1 864MB New F older Format Cancel 0202021030315 21 First Choice for Security Professionals HANGZHOU HIKVISION DIGITAL TECHNOLOGY CO LTD www hikvision com
18. ue wed Thu Fri Osat C Sun Cop 1 Configure All Day or Segment Record Fri End Time ar ET Ee eee E E E E Record Type Normal Normal Normal Normal Normal Normal Normal MEIMEI E NS IES Normal OK Cancel If you want to configure the all day recording please check the All Day checkbox If you want to record in different time sections check the Segment Record checkbox Set the Start Time and End Time Note The time of each segment can t be overlapped Up to 8 segments can be configured 2 Select a Record Type The record type can be Normal Motion Alarm Motion amp Alarm and Motion Alarm 3 Check the checkbox of Select All and click Copy to copy settings of this day to the whole week You can also check any of the checkboxes before the date and click Copy 4 Click OK to save the settings and exit the Edit Schedule interface Click Advanced to configure advanced record parameters 13 Quick Operation Guide of Digital Video Recorder Te Click Save to validate the above settings Playback Channel No ED Embedced Net DVR Camera 01 Camera 02 Interface Introduction 1 Channel List Displays the list of channels and the playing status of each channel 2 Playback Window Displays the image of channel 8 Play Control Bar Play control operations are supported 4 Time Line
Download Pdf Manuals
Related Search