User Manual
Contents
1. 1 1 1 Leaning forward Do not extend your chest beyond the armrest figure 4 In order to reach an object in front of you you must lean and bend down therefore you must use the castors as a tool pointing them forward to maintain stability and balance An accurate alignment of the wheels is essential for your safety figure 5 1 1 2 Leaning backward Position wheelchair as close as possible to the desired object so that you can simply pick it up by stretching your arm while sitting in the chair in a normal position In any case do not lean backwards because you may cause the chair to tip figures 6 and 7 N Warning The hanging of back packs or similar items onto your chair backposts can affect the rearward stability of your chair especially when used in combination with recliner backrests This can cause the chair to tip backwards causing injury Therefore Invacare strongly recommend the use of anti tippers available as an option when using your backposts to carry a back pack or similar items I 2 Transferring to other seats 1 2 1 Sideways transfert This may be done without assistance provided that you are sufficiently mobile and have a strong enough torso Move the wheelchair as close as possible to the seat to which you would like to sit with the castors pointed forward Lock the wheels by appl2. right or left available The removable and interchangeable rear wheels facilitate transport as well as change of the control side To dismantle the wheel pull the button A and remove the wheel from its support A To prevent falls and injuries it is essential that the button A is fully engaged providing perfect locking of the rear wheels 2 Two positions of the small handrim are possible to facili tate the propulsion internal position 2 external position Unscrew the three fixation bolts B position the small handrim depending on the needed configuration firmly tighten the three bolts To fold the wheelchair take the transmission shaft C off by sliding one part inside the other To facilitate this operation move the small handrim forwards to backwards You can now roll the folded wheelchair A Please note that the transmission shaft is an integral part of the wheelchair and the user will be unable to propel the wheelchair without it 29 30 2 6 3 Safety equipment and options Posture belt Velcro fastener photo 34 position the two Velcro strips one over the other based upon the user s build Buckle fastener photo 35 to close the buckle engage part A into part B to open press C Straps should be adjusted to suit user insert into part B of the buckle and adjust the loop D based on the remaining length Ain case the posture belt has to be replaced the new belt fixa
3. PORTUGAL Lda Rua Estrada Velha 949 4465 784 Lega do Balio Portugal 351 225105946 Fax 351 225105739 Invacare AB Fagerstagatan 9 163 91 Sp nga Sverige kundtj nst 46 0 8 761 70 90 Fax kundtj nst 46 0 8 761 81 08 Invacare B V Celsiusstraat 46 NL 6716 BZ Ede The Nederland 3 0 318 69 57 57 Fax 31 0 318 69 57 58 Invacare Ltd South Road Bridgend Industrial Estate Mid Glamorgan CF31 3PY United Kingdom T Customer Service 44 0 1656 647 327 Fax Customer Service 44 0 1656 649 016
4. adjustment e e e on the fork angle Make sure that the 2 castors come in e e e contact with the ground at the same time 3 2 General inspection Your distributor who has the required technical expertise is responsible for any wheelchair repairs We recommend that you take the wheelchair to your re tailer at least once a year for a complete inspection Regular maintenance allows the identification and replacement of defective and worn parts which improves the daily opera tion of your wheelchair Regular inspections to be performed by you or your assistants a General Make sure that the wheelchair folds and unfolds easily Make sure that the wheelchair moves in a straight line no resistance or deviation b Manual brakes Make sure that the manual brakes do not touch the moving tyres Make sure that the manual brakes operate easily Make sure that the joints are not worn and do not have play c Folding system Check the folding system for worn or distorted parts d Skirtguard armrest upholstery Make sure that all the fittings are properly tightened e Armrests Make sure that the armrests are firmly attached but easy to remove f Armpad Make sure that the armpads are in good condition g Seat and backrest upholstery Make sure that the upholstery is in good condition h Rear wheels Make sure that the wheel nuts and precision bearings are tight Make sure that the wheels a
5. in all directions If a cushion is changed it may also change the users stability Invacare provides a wide range of seat cushions adap ted to your needs Please contact your dealer 2 1 2 Type of backrests Standard fixed backrests This backrest do not require adjustments they can be equip ped with padded backrest or tension adjustable backrest Height adjustable fixed backrest photo 2 Fold the chair slightly to facilitated the operation loosen screws A with an Allen key 5 mm Adjust to the desired height and firmly tighten the two screws A Folding backrest photo 3 45 cm backrest height To save space when transporting folded and unoccupied operate lever B by pulling or pushing it and fold the top of the backrest To return to the initial position bring the top in the vertical position it locks automatically VINA make sure that the backrest is properly locked in place before the user settles down in the wheelchair to prevent any injuries Reclining backrest 0 30 39 41 43 cm short cane tube or 47 49 51 cm long cane tube backrest height The intended use of reclining backrest is to get a relaxing comfort position for the user It is not indented to be used in a dynamic situation and it should be used on horizontal surface when the backrest is reclined especially when the backrest angle is more than 10 Anti tippers are recomman ded for those who need to feel safer or have a
6. seat and to stow the wheelchair safely and securely in a separate compartment Test report from dynamic safety restraint test 11 ISO 7176 19 Test no P501858A fixed backrest amp P501858B Folding backrest Customer Invacare Rea AB Date 2005 04 05 The safety restraint devices used in this test must be appro ved according to ISO 10542 We have chosen to work with Unwin a well known quality manufacturer of safety restraint devices for wheelchairs Restraint system manufacturer may improve its products please contact them for more details 12 4 1 Observations before transport of wheelchairs in vehicles We recommend that wheelchair users should transfer to the seat of the vehicle and use the installed restraint system of the vehicle whenever feasible e The wheelchairs are tested in a basic configuration The use in other configurations has not been tested Please contact your dealer for further information Auxiliary wheelchair equipment is either secured to the wheelchair or removed from the wheelchair and secured in the vehicle during transit i e table trays Alterations or substitutions are not to be made to points of the wheelchair or to structural and frame parts without the written consent of Invacare A wheelchair anchored posture belt with metal buckle must be fitted across the wheelchair occupant in addition to the lap and diagonal occupant restraint 3 point belt Belt restraints are no
7. specific usage Simultaneously pull the levers A to provides the same angle on both sides release the levers when you reach the desired angle photo 4 e Mechanical version 17 There are 4 angles position by step of 10 Note Push on the backrest canes before operating the levers this is to release the auto locked security system Photo 5 18 e Gas strut version 0 to 30 continuously 43 cm short cane tube or 51 cm long cane tube backrest height Photo 6 The gas struts provide a help to the attendant to raise the user always operated with the user seated in the wheelchair Ar is recommended that this operation be performed only by the attendant Always make sure that the backrest is locked in place to ensure perfect safety for the user Keep away fingers from moving parts levers cylinders mechanisms etc to prevent injuries The backbrace B photos 6 amp 7 links the two push handles and must always be in position on recliner versions see para graph 2 6 1 Avoid operating levers A photo 7 during a sideways transfer for example in order to prevent destabilising the user s posi tion To ensure safety for the user when backrest is reclined we recommend to use anti tippers available as an option Maintenance of reclining backrest mechanism varies with use Please contact your Dealer Based upon the development of your disability you can choose an Invacare Action NG backrest
8. width mm 580 805 lenght Ed Drum brake mm Width of Lenght folded 305 without 830 900 wheelchair footrest mm mm Distance Total between height 900 1030 front wheel and 390 550 mm rear wheel mm Height from Backrest ground o 360 510 angle 0 80 back seat 0 i mm Height from Bracket ground to front seat 385 510 ie 80 mm Backrest Distance height between mm 380 510 footrest and 350 480 seat mm Wheelchair ps height when backrest is N A Armrest aa 250 350 folded mm nim mice fm Picture Description id Fixed armrest Maximum height 200 260 piele 128 mm eig NE mm Adjustable Maximum 21 armrest 190 295 oi us height mm Pe 07 Sheds Notched Maximum 18 i armrest 130 up Static height mm t ay 2m obstacle Rear wheel ee 18 5 di t ateral Static k pi 560 610 super elevation on 1 0 obstacle i Wheels A med t Removable armrests diameter 470 520 V parts e mm Footrests Overall Seat plane weight ange 0 6 when empty 15 15 5 Sa Kg kg Height User s Q SS without rear 605 maximum 125 wheel weight 160 mm m kg Weight of the Taming heaviest 9 iata 850 removed part mm Kg kg i Nylon M4 Sa lia j Seat material y depth 50 Fire class EN 10211 mm NF EN 1021 2 33 Yes you can 1533727 UK V1 07 2009 Invacare France Oper
9. 0mm or in 6 150mm diameter and a single width of 3 8 32mm They can be delivered with pneumatic or solid tyre A 5 100 mm diameter soft roll medium hard is available Note refer to paragraph 2 3 1 for regular maintenance 2 42 Front fork Different fork positions are available based upon the selection of floor to seat height castors and rear wheels Please take advice from your dealer if you want to replace or remove the castors or rear wheels 26 2 5 Brakes 2 5 1 Manual brakes The manual brakes photo 24 are designed to secure the wheelchair during long stops They are not intended to slow down the wheelchair or to be used as support during a transfer They must be operated simultaneously In order to brake push the handle A forward The handle folds back to facilitate transfers Draw as a preliminary the handle upwards Once the brakes are engaged the wheel chair should not move at all Note brakes adjustments are based upon the diameter and type of the wheels After repairing a flat tyre or in the event of wear of the pneumatic or solid tyre you may need to adjust the brake s To adjust the brake s loosen the two screws B and slide the brake assembly to obtain the following distance value between the wheel and the brake shoe in unlocked position photo 25 A Please make sure this adjustment is always done as des cribe whatever the chair configuration is Solid tyre X 6 mm Pneu
10. 16 Lean backward cautiously and your centre of gravity will move backward to a more stable position Now let the hand rims slide in your hands Be ready to react at any moment to control speed and direction VIN warning Avoid turning suddenly and never try to climb and descend a ramp diagonally figure 17 ex Standard configuration for fixed backrest The position of the rear wheel axle and the angle of your wheelchair s backrest are two of the key adjustments that can affect your stability whilst sat in the wheelchair see figure 14A It is recommended to avoid using ramps with a slope greater than 9 degrees and do not attempt to turn whilst on a slope The wheel position is usually factory set and should not be change unless by the direction of a competent person who must have assessed the impact of the change on your stability in normal use If your wheelchair is fitted with a recliner backrest it is recommended that anti tippers are also fitted and used whenever the backrest is reclined from the upright position Q Operating instructions 2 1 Unfolding and Folding the wheelchair 2 1 1 Unfolding the wheelchair figure 18 With one hand grab the armrest or the seat support tube on one side of the wheelchair and slightly tilt it to wards you so that the rear wheel and castor lift from the ground With the other hand push on the seat tube until the upholstery is fully extended and seat tu
11. Invacare Action NG UK User guide Foreword The information contained in this manual is subject to change without notice Some information is submitted under copyright all rights reserved Any information in this document cannot be photocopied or duplicated without prior written authorization by Invacare As the European and world s leader manufacturer of wheelchairs Invacare endeavours to supply a wide range of wheelchairs to meet all the needs of the user in everyday life However final selection of the wheel chair rests solely with the user and his her qualified health advisor Proper and efficient use of the wheelchair that you have chosen is based upon the medical prescription which was issued for you on the basis of your pathology and the nature of your disability Your wheelchair is especially designed to be used indoors and with certain restrictions outdoor Please look at N warning paragraphs Part A General Guidelines Please comply with traffic regulations Stamp of the Distributor Introduction Dear Customer Thank you for purchasing an Invacare wheelchair This model was designed to provide you with all the benefits and features to meet your needs Only quality components were selected for your wheelchair based upon rigorous inspections during the entire manufacturing process This product conforms to the requirements of Council directives 93 42 EEC related to medical devices class one product by appl
12. ations SAS ERIE Route de Saint Roch 37230 FONDETTES Invacare Australia Pty Ltd I lenton Place North Rockes NSW 2151 Australia 61 2 8839 5333 Fax 61 2 8839 5353 Invacare n v Autobaan 22 8210 Loppem Brugge Belgium amp Luxemburg 32 50 831010 Fax 32 50 831011 Invacare AIS Sdr Ringvej 37 2605 Br ndby Danmark Zi kundeservice 45 0 3690 0000 Fax kundeservice 45 0 3690 0001 Invacare Aquatec GmbH AlemannenstraBe 10 D 88316 Isny Deutschland 49 0 75 62 7 000 Fax 49 0 75 62 7 00 66 European Distributor Organisation Invacare KleistsraBe 49 D 32457 Porta Westfalica Deutschland 49 0 31 754 540 Fax 49 0 57 31 754 541 Invacare SA c Areny s n Poligon Industrial de Celr 17460 Celr Girona Espa a 34 0 972 49 3200 Fax 34 0 972 49 32 20 Invacare Poirier SAS Route de St Roch F 37230 Fondettes France 33 0 2 47 62 64 66 Fax 33 0 2 47 42 12 24 Invacare Mecc San s r l Via dei Pini 62 1 36016 Thiene VI Italia 2 39 0 445 380059 Fax 39 0 445 380034 Invacare Ireland Ltd Unit 5 Seatown Business Campus Seatown Rd Swords County Dublin Ireland 353 8107084 Fax 353 8107085 Invacare NZ 4 Westfield Place Mt Wellington Auckland New Zealand kundeservice 64 22 57 95 10 Fax kundeservice 64 22 57 95 01 Invacare AS Grensesvingen 9 0603 Oslo Norge kundeservice 47 22 57 95 10 Fax kundeservice 47 22 57 95 01 Invacare
13. be sits in receiver Then engage the two manual brakes open the footrest legrest and check the ground clearance footrest ground distance see paragraph B 2 1 4 You can now sit down in the wheelchair 2 1 2 Folding the chair figures 19 amp 20 Fold and lock the footrest legrest toward the front of the wheelchair Swivel the plates into the vertical position Using both hands take the centre front and back edges of the seat upholstery and lift it Or tilt the wheelchair to one side and close it using the handles on the backrest Z Warning Fold the wheelchair while keeping the seat upholstery upwards to avoid damage by the folding system Caution possible finger pinch 2 2 Wheelchair propulsion Self propelling wheelchair propulsion is achieved through the use of the handrims mounted on the wheels The distance between the wheels axle position and the seat height can be adjusted to allow you to hold the handrims properly and various accessories can be added to improve the grip anti slip plastic coated etc Qualified medical and paramedical staff will be able to provide you with advice regarding the propulsion which is best adapted to your disability Any wheels adjustments to the set up of your wheelchair see paragraph 2 2 2 should only be performed at the direction of a competent person who has fully risk assessed the implication of any changes to the wheelchair configuration 2 3 Lifting the wh
14. dants one in front of the wheelchair and one behind the wheelchair N Warning 3 we recommend that users over 100 kg in weight do not use this starway manoeuvre To climb stairways figure 13 After tilting the wheelchair to the point of equilibrium one assistant at the back holds the wheelchair up against the first step grasping the handles firmly to lift The second assistant lifts the wheelchair above the stairs while holding firmly a fixed part of the frame and holds it while the first assistant takes a step and repeats the opera tion The wheelchair must not be lowered until the last step has been passed and the chair is clear of the stairs To descend stairways Same operation as above however reverse steps as above A Wetting Do not attempt to lift the wheelchair by any removable parts such as armrests legrests or footrests Avoid using an escalator which may lead to serious injury in the event of a fall 1 6 Slopes It is recommended to avoid using ramps with a slope higher than 9 The wheelchair risks tipping over in the event of spinning or side movement figure 14 Upward slopes figure 15 Lean the upper body forward and your centre of gravity will move forward to a more stable position Now move the wheelchair forward with short quick pushes on the hand rims to maintain speed and direction control If you want to rest apply both brakes when stopping Downward slopes figure
15. eelchair First folds the chair see paragraph 2 12 always lift the wheelchair by gripping the frame at the points A shown in the figure 21 AN Never lift the wheelchair by removable parts armsrest footrests Ensure the backrest posts are securely in place 10 Q Safety inspection and maintenance 3 1 Performance control As the user you will be the first to notice any possible operational defects with your wheelchair The following table indicates the easiest troubleshooting symptoms to identify and the preliminary inspection that you can perform In the event that the symptoms persist after adjusting the pressure in the tyres and tight screws and nuts please con sult your retailer The inner tubes of the wheels are the only components that you can repair yourself see paragraph B 2 3 If the screws and nuts are not tight enough or loose the axle fork angle is not perpendicular to the ground please consult your retailer to get a competent person to re set them to the correct position and tighten appropriately Recommended torque minimum M5 4 Nm M6 7 Nm amp M8 17 Nm pane A ihe Ud i The Creaking Play in wheelchair wheelchair wheelchair ti d the swerves swerves turns or Sie dinkin wheelchair Inspections to the to the left moves 8 right slowly Make sure that pressure in the e e e pneumatic tyre is correct cf B 2 3 Make sure that the e e e e bolts are tight Check the
16. eriod of warranty any parts that have become defective due to faulty workmanship or materials will be renewed or repaired without charge by the Invacare dealer supplier The warranty will be forfeited should any unauthorised alteration be made to the equipment The Purchaser s statutory rights under the Consumer Protection Act are not affected 5 2 Limitation of liability This warranty does not extend to the consequential costs resulting from fault clearance in particular freight and travel costs loss of earnings expenses etc Invacare shall not be liable for Natural wear and tear Inappropriate or incorrect use Defective assembly or setting up by the purchaser or third parties Defective or neglectful treatment use of unsuitable spares 6 Summary of operating instructions for optimal safety Maximum user s recommended weight 125 kg or 160 kg Do not attempt to reach objects if you have to move forward in the seat Do not attempt to pick up objects from the floor by rea ching down between your knees Do not lean over the top of the upholstery back to reach objects located behind you this may cause you to tip over Always engage both manual brakes simultaneously Manual brakes are parking brakes they must not be used in any case to slow down the wheelchair or as support during transfers Do not tilt the wheelchair down kerbs or steps without using an assistant Press down on t
17. g instructions TABLE OF CONTENTS Page NN DD WW v OO 10 10 12 13 14 14 B DESCRIPTION OF YOUR CHAIR GI Presentation I I Introduction 1 2 General description 2 Adjustments if Seat 2 1 1 Seat upholstery 2 1 2 Type of Backrest 2 1 3 Backrest upholstery 2 1 4 Footrest supports 2 1 5 Armrests 2 1 6 Comfort version 2 Frame 2 2 1 Side frame 2 2 2 Double folding system 2 2 3 Steering tube 2 3 Rear wheel 2 3 1 24 amp 22 wheels 2 3 2 Handrims 2 3 3 Axles 2 4 Castors 2 4 1 8 6 amp 5 wheels 2 4 2 Front fork 2 5 Brakes 2 5 1 Manual brakes 2 5 2 Hub brakes 2 6 Options amp accessories 2 6 1 Seating options 2 6 2 Propulsion options 2 6 3 Safety equipment and options 2 6 4 Other options 2 Specification and tool s 3 1 Standard wheelchair specifications 3 2 Tools for adjustments and regular maintenance Not supplied 3 3 Dimensions Page 15 15 16 16 17 18 19 20 21 23 23 23 23 24 24 24 25 25 25 25 26 26 27 27 27 28 30 3l 32 32 e GENERAL GUIDELINES whilst the line of your combined centre of gravity lies within the points of contact of the forward and rear wheels with gl Safety and operating limits he RA For a safe operation of your wheelchair the following parame Weight imit tersshouldbecebse rved The maximum recommended weight of the user is 125kg Stability and balance and 160 kg for 50 5 55 5 amp 60 5 cm seat width However Your w
18. he lower tube of the frame as well as pulling on the push handles Do not carry in the stairways or escalator user seated in the wheelchair with only one attendant this may cause serious injury Do not use the wheelchair unless it has the proper tyre pressure Front 250 kPa Rear 350 kPa Do not overinflate the tyres this may cause the tyres to explode and cause bodily harm Do not expose the wheelchair to a temperature higher than 40 C To avoid injury keep your fingers away from mobile parts ar mrests folding system legrests footrests and maintain good posture before lifting the wheelchair heaviest part 9 Kg A Avoid riding on wet areas as well as gravel grass etc Sand and sea water particularly damage ball bearings When using the wheelchair inside we recommend using solid tyre castors especially when riding on carpet e DESCRIPTION OF YOUR WHEELCHAIR E PRESENTATION 1 1 Introduction Your wheelchair has been factory set before you purchased it However it must be specifically adapted to your needs The following detailed paragraphs describe the various functions and possible adjustments as well as available options You can make some adjustments yourself while others can be made only by your dealer Important based upon the selected model or options your new Invacare Action NG wheelchair may be not equipped with all of the components or options which are described in the follo
19. heelchair has been designed to provide the stability the level of activity is an essential factor For example an you need during normal daily activities active user who weighs 75 kg may subject the wheelchair to Any movement in the wheelchair will have an impact on more stress than user who weighs 100 kg To this purpose the position of the centre of gravity which may lead to the we recommend that you consult your retailer when choosing wheelchair tipping and a fall the model of wheelchair based upon your daily life style To improve your safety when you move a lot or you transfer your weight from one place to another we recommend using 1 Reaching an object from the chair seat belts The limitations on reaching out from a wheelchair indicated Weight distribution figure 1 in the following diagrams have been calculated based on a Many actions cause the user of a wheelchair to reach out representative sample of wheelchair users lean over or move about within the wheelchair and outside Only the arms should be extended beyond the seat of the it Any movement you make whilst sat in your wheelchair wheelchair figure 2 will move the combined centre of gravity of you Gc and The body and head should remain within the boundaries of the wheelchair Gw You will remain stable in the wheelchair B the seat figure 3
20. ication of following standards NF EN ISO 14971 and NF EN 12182 This manual describes the operating limits of your wheelchair maintenance operations and adjustments that you or your assistant can make However all the repairs except for inner tubes as well as some adjustments require specific technical training and therefore must be performed by your distributor The Invacare Action NG is designed for both indoor and outdoor use with the purpose of helping people who are not able to walk over a long distance Even though your Invacaree wheelchair has been designed to provide a long and trouble free life it is inevitable that wear tear and usage will eventually render the product unusable Invacare amp recommends that the average usable life of this product is five years providing the product has been correctly maintained according to the manufacturers recommendations A GENERAL GUIDELINES Safety and operating limits 1 1 Reaching an object from the chair 1 2 Transferring to other seats 1 3 Tilting 1 4 Tilting kerbs 1 5 Stairways 1 6 Slopes 2 Operating instructions Folding and Unfolding the wheelchair 2 2 Wheelchair propulsion 2 3 Lifting the wheelchair 3 Safety inspection and maintenance Performance control 3 2 General inspection 64 Transportation 4 1 Observations 4 2 Restraint systems 5 Summary of warranty terms 5 Standard terms 5 2 Limitation of liability 6 Summary of operatin
21. in the frame tube in order to prevent any falls b Tipping lever photo 38 it allows the attendant to easily tip the wheelchair when crossing an obstacle pavement step etc push down the lever with your foot right or left and maintain balance using the push handles The tipping lever is mounted the same as the anti tippers in the same tube Note Make sure that the anti tipper wheel is ALWAYS located out side the rear wheel volume All these adjustments and changes of position must be per formed by a professional technician because these can affect the stability and the safety of the user Please consult your dealer 2 6 4 Other option Transparent tray photo 39 it is positioned on the armpads of the armrests full length ones only Slide the tray forward or backward based upon the user s build Abs not place very heavy and unstable objects containers with very hot and corrosive liquids on the tray which may cause serious injury if they fall 31 32 Specifications and tool s 3 1 Standard wheelchair specifications Maximum user weight Seat width Seat depth Floor seat height Rear wheel Castors Parking brake Backrest Armrests Footrest supports amp Legrests Seat upholstery Frame Wheelchair average weight 125 kg 160 kg 38 40 5 43 45 5 48 cm 50 5 55 5 60 5 cm 40 45 cm 51 48 5 46 43 5 41 38 5 cm 24 610 mm pneu
22. juries during folding and unfolding Comfort backrest photos 19 amp 19A It is made up of a rigid shell A and a preformed foam cushion B which is locked in place by Velcro fasteners thus providing optimal comfort The backrest is removable to allow the folding of the wheelchair loosen both buttons C slide the levers D to the inside and disengage the hooks E from their supports Reverse the procedure to reassemble the backrest A A It is recommended that this operation be performed only by the attendant Always make sure that the backrest is locked in place for optimal safety of the user Make sure the backrest cushion Velcro fasteners are in good state and well positioned Keep your fingers away from mova ble parts to prevent injuries Note for maintenance of your DARTEX cover only use a soft rag soaked with alcohol Comfort headrest photo 20 It is removable completely loosen the ball screw A It is height adjustable slightly loosen the ball screw A adjust to the desired height tighten without forcing The cushion also is angle depth and height adjustable by ope rating simultaneously the lever B and screws C Note make sure that the indexable lever is properly oriented to prevent any bother or injury to the user or attendant A Do not adjust the head rest when the user leans on it and check the mounting to the backrest in order to prevent injuries Prams All these adjust
23. k the two brakes they should not be used in any case as support for transfers Never stand on the footrests when you are getting in or out of the wheelchair figure 10 1 3 Tilting balancing on the rear wheels For greater safety this operation must be performed by an attendant The attendant should be aware of the required physical effort and use appropriate positioning in order to relieve the strain on his her back keep a straight back and bend your knees during this operation To tilt the wheelchair the attendant must firmly grab the han dles making sure both are properly fixed Warn the occupant in the wheelchair before tilting it and remind him her to lean backwards and make sure that both feet and hands of the user are clear of the wheels Place a foot on the footstep tube and move continuously until the chair reaches the equi librium point At this stage the assistant will feel a difference in weight distribution which usually occurs at approximately 30 At this point the wheelchair can get over the obstacle easily Finally the attendant slowly and gradually lowers the front down to the ground while firmly holding the handles DS Wang E Be aware of detachable parts such as armrests or legrests they must NEVER be used as lifting supports as they may be inadvertently released resulting in possible injury to the user and or attendant Do not lower the wheelchair suddenly even if it is severa
24. l centimetres from the ground as this may result in injury of the user 1 4 Tilting Kerbs To get on the pavement Method figure 1 The attendant positions the wheelchair in front of the pave ment facing forward Press down on the lower tube of the frame or on tipping levers delivered as an option as well as pulling on the push handles Attendant tilts the wheelchair backwards until the castors reach the pavement attendant pushes the wheelchair forward until the rear wheels are against the kerb and again pushes the wheelchair until the rear wheels climb over the kerb Method 2 figure 12 In this case the attendant stays on the pavement and tilts the wheelchair in a backwards position with the rear wheels against the kerb The attendant tilts the wheelchair bac kwards until it is balanced and pulls the wheelchair with a steady movement until the rear wheels climb over the kerb then he she lowers the castors while making sure that the chair is far enough on the pavement so that the castors do not fall into empty space To get off the pavement The attendant positions the wheelchair facing forward on the pavement and tilts it backwards until it is balanced then he she pushes the wheelchair forward until the rear wheels touch the road after getting over the obstacle then he she gradually lowers the castors to the ground 1 5 Stairways Because this is a difficult movement we recommend using two atten
25. matic tyre 8 200 mm solid tyre Manual brake with indexed brake shoe Fixed folding and reclining Removable removable and swing away Removable and swing away Black nylon on reinforced upholstery Aluminium epoxy coated 15 kg 3 2 Tools for adjustments and regular maintenance not supplied Function Tool Brake 5 mm Allen key Footrest tube 5 mm Allen key Footplate 5 mm Allen key Adjustable armrests n 5 5 mm Allen key Simple armrests n 4 mm Allen key 10 mm open end wrench T20 Torx key 13 mm open end Wrench X 2 19 27 mm open end wrench 11 19 mm open end wrench Armpad Castor Quick release axle After sale and disposal recommendations It is compulsary to use original Invacare spare parts which you can buy through any Invacare dealer For repair please contact your local Invacare dealer Disposal the metal parts can be disposed of for scrap metal through recycling Plastic parts are disposed of as plastic scrap Disposal must be carried out in accordance with the res pective national regulation Please apply to your municipal authorities local government for details about local disposal companies 3 3 Dimensions Picture Description value i Picture Description valu Backrest Seat effective 380 605 height 1045 width mm including 1290 headrest mm 590 815 Overall 1050 Overall dig
26. matic tyre X 5 mm Nrimy tighten the screws B after adjustment Keep your fingers away from movable parts to prevent injuries 2 5 2 Hub brakes Besides the functions provided by manual brakes the hub brakes provide the slow down for example on a slope and improved safety because they are still efficient when you have a flat tyre Two versions are available photos 26 amp 27 atten dant control and dual control attendant and user To slow down gradually pull the lever A upwards To lock the brake in parking position with the lever A tightened push the lock B to engage it in the notches of the brake handle then pull the lock up to unlock To adjust braking turn the screw C counterclockwise to increase braking force and turn clockwise to reduce it The specific adjustments of hub brakes must always be performed by your Dealer Ai operate the two brakes simultaneously and do not take slopes exceeding 5 to ensure perfect control of the wheelchair steering 2 6 Options 2 6 1 Seating options Back brace photo 28 it provides tension to the backrest upholstery and provides the attendant better ergonomics when pushing the wheelchair Note it swings away to facilitate the wheelchair folding slightly loosen the button A pull up and swivel along the backrest until it is in vertical position To reposition it reverse the procedure and firmly tighten the button A making sure tha
27. ments and changes of position must be 2 2 1 Double folding system performed by a professional technician upon agreement by It consists of two double cross bars which integrate seat rails your prescribing physician Please consult with your dealer To fold and unfold your wheelchair see chapter A General ECT URL HN CERE IRR D 227 24 22 24 6 amp amp 8 paragraph 2 1 EL a z 2 2 2 Side frame The sides or side frames are designed to accommodate the Spa Alea p e p rt 22 24 22 24 6 8 6 sg steering tubes for the castors and multiple adjustment wheel Em pup Eek mounting for rear wheels e tet tate e to m 51 3 3 These wheel mountings allow five height positions and two H PET Pi Seat Angle 6 Rear Support Headset Support longitudinal positions Standard serial delivery with fixed or Seat Height Posten 1 Posten Pan Postion Z folding backrest Passive backward for better stability serial ES ru imm with reclining backrest and Transit 12 version eters tet sts oe Dual amputee position option or accessory to prevent back tip with Amputee user s the rear wheel axles can be positioned backwards from the backrest cane axle specific manual brakes are included in the kit for a better stability A The above information is given to
28. of the Velcro fasteners Always make this adjustment before the user settles down in the wheelchair to prevent injuries Before making adjustments please ensure that the wheelchairs is fully opened These adjustments is to curved the backrest upholstery don t make it flat it will be uncomfortable for the user 2 1 4 Footrest supports Standard footrest supports photo 9 they swing away du ring transfers and can be removed during transport Operate lever A by pushing sideways and swivelling towards outside or inside in case there is not enough space To re turn to the initial position align the footrest support it locks automatically To remove the footrest support simply pull up after unlocking the assembly Reverse the procedure to reassem ble while still in the unlocked position Legrest photos 10 amp 11 performs the same operation as for the footrest support to swing away or remove the legrest by operating lever A which unlocks the locking system To adjust the angle pull the lever B with one hand while supporting the legrest with your other hand When a suitable angle is obtained let go of the lever and the legrest will look into one of seven preset positions schema 10 A The calfpad swings away during transfers and is height adjustable by sliding After loosening the screw C adjust to the desired height and firmly tighten the screw C In 20 addition it is depth adjustable loosen the scre
29. re parallel to the frame i Handrims Check for rough patches j Spokes Make sure that the spokes are not distorted loose or bro ken k Castors Make sure that the axle is tight by turning the wheel the wheel must gradually come to a stop Fork steering tube Make sure that all the fittings are well tightened m Pneumatic and solid tyres Check the pressure of the pneumatic tyres Front 250 kPa Rear 350 kPa check the wear of the solid tyre tread n Cleaning and disinfection Cleaning Use only damp clothes and gentle detergent Do not use abrasive or scouring liquid Do not use high pressure cleaning devices on ball bearings front amp rear wheels fork axles Make sure you dry the wheelchair if it is wet e g after washing it or going out in the rain Disinfection Spray or wipe disinfection using a tested and recognised product is permitted Please pay attention to the manufacturer s instructions of the medical product desinfectant you are using dd Transportation Transport of wheelchairs in vehicles The Invacare Action 4 has been tested for safety in collisions according to ISO 7176 19 Invacare Action can be used for transport in vehicles that have been specially adapted for this purpose The wheelchair must be securely fastened in the vehicle according to the methods described on the following pages Remember that the best solution is always to move the user from the wheelchair into a normal car
30. ry it is recommended to request your dealer to replace them C A Refer to paragraph 1 2 2 Front transfert for safety instructions WVhen folding back down ensure that it locks in place otherwise it can act as a long lever and could fatigue Note the armrests are mounted in pairs on the wheelchair whenever you remove them remember that you have a right and a left side AN Nei lift the wheelchair by the armrests Keep your fingers away from movable parts during folding disassembling or adjustment to prevent injuries 2 1 6 Comfort version 21 The Action Comfort version wheelchair for passive user is not designed or tested to be used as a seat in a vehicle not crash tested it is necessary to use a vehicle seat adapted to yout transportation The Action Comfort version is always delivery in passive position rear wheel support plate for a better stability Comfort seat photo 18 22 It is removable allowing the folding of the wheelchair simply lift the cushion and put it away then grab the two seat holding tubes and pull them upwards Repeat the operation in reverse order to unfold the wheel chair see paragraph 2 1 1 The padding and outer cover of this seat will wear please contact your dealer for possible replacement Make sure the cushion is properly positioned on the 3 seat Velcro fasteners to provide safety and comfort for the user Keep your fingers away from movable parts to prevent in
31. s Removable simple n I photo 14 to remove armrests simply pull them up Previously press on the push pin D lo cated at the bottom of the armrest vertical upright Reverse the procedure to reinstall them To adjust their height 3 positions remove the screw A adjust to the desired height and reposition the screw A tighten without forcing The armrests with central fixation n amp n 4 from now on are equipped with a support adjustable in 2 parts which enables you to reduce the plays and to facilitate the vertical tube extraction it is necessary to tighten or loosen the 4 screws B according to the anticipated result photo 15 Swing away removable n 2 photos 16 amp 17 This range of armrests can be swung away to facilitate transfers and disassembling during transport To swing the armrest away push down the dog point A reverse the procedure to reinsert making sure that the dog point B is properly engaged in its housing To remove the armrest swing it back completely and pull it up Reverse the procedure to reinstall The new design includes handle C and hollowed skirt guard D to facilitate front transfer Grip firmly the armrest handle take care of your nails on the skirt guard edges Push on your arms to easily lift yourself up and the attendant can help you to finalise the transfer to the place where you wish to sit In the event the armrest handle covers C become slippe
32. t the button is properly tighten B 27 28 Swing away back brace photo 29 Press the push pin C and fold down the back brace Reverse the procedure to reinstall Note that the push pin C should be locked in its hole A mre swing away back brace is not a push bar A It is important to ensure that the backbrace is correctly fitted and engaged at all times when the chair is in use see label on the backbrace photo 30 ZNbs not lift the chair by handling the back brace There is a risk to unlocked the back brace by push it up Keep your fingers away from movable parts to prevent injuries 2 6 2 Propulsion options Transit version photo 31 the wheelchair is designed to be driven only by the attendant To facilitate sideways transfers and save space the wheelchair is equipped with rear wheels of 12 315 mm with pneumatic or solid tyre Note Transit version equipped with a reclining backrest is always fitted with anti tippers The manual brakes optional hub brake are only accessible to the attendant operate the handle A to lock the wheel chair in parking position Note for further information about the use of the two types of brakes see paragraphs 2 5 1 amp 2 5 2 Dual handrim DHR photos 32 amp 32 This new quick release system allows the user to drive the wheelchair with a single arm using two handrims on the same wheel with 2 possible side positions of the small han drim
33. t to be held away from the body by wheelchair components or parts such as armrests postural restraints wheels etc Picture 22 The wheelchair must be securely fastened in the vehicle with an ISO 10542 2 approved 4 point belt system according to the methods described in the manual The occupied wheelchair must be tied down in an forward facing configuration with the parking brake applied The wheelchair backrest should be positioned as close as possible to 90 degrees Please observe that even if these products and recommen dations are provided in order to increase safety injury to vehicle occupants still might occur in the event of a collision or other accidents and no guarantee is given in this respect Correct and incorrect placements of 3 point belt picture 22 4 2 Restraint systems pictures 23A amp 23B Non contractual picture only for information Please refer to best practice recommended instructions from the safety belt manufacturer A Frontal restraints with straps picture 23A Connect the frontal straps around the frontal part of the frame See location of the attachment labels 2 Release brakes and tension front straps by pulling the wheelchair backwards from the rear 3 Re apply wheelchair brakes B Rear restraints pictures 23A for self propelling amp 23C for Transit version Attach the snap hooks on the rear straps to the frame just above the rear wheel attachments See loca
34. that meets your needs Please consult with your Dealer A If you consider there is an excessive free play in the recliner mechanism after a simple visual examination of the ratchet please contact your Dealer To ensure safety for the user when backrest is reclined we recommend to use anti tippers available as an option A N Tre hanging of back packs or similar items onto your chair backposts can affect the rearward stability of your chair especially when used in combination with recliner backrests This can cause the chair to tip backwards causing injury Therefore Invacare strongly recommend the use of anti tippers available as an option when using your backposts to carry a back pack or similar items 2 1 3 Backrest upholstery Standard upholstery backrests In the event that the upholstered backrest slackens ask for a replacement from your Dealer B Contour Tension adjustable backrest photo 8 amp 8A con tour allows adjustment of the backrest curvature based upon user s body posture to provide the best comfort as possible PS Pm making adjustments please ensure that the wheel chair is fully opened the seat rails are properly located and a back brace C is perfectly fitted on the chair see instructions paragraph 2 6 1 Lift the flap A and pull the straps B in order to stretch or slacken them Each strap can be adjusted separately Reposition the flap A A check the quality and positioning
35. the user for informa tion only Any wheels position and or angle fork adjustments to the set up of your wheelchair should only be performed at the direction of a competent person who has fully risk assessed the implication of any changes to the wheelchair configuration Please consult your dealer 2 2 3 Steering tubes They provide seat dump 0 3 or 6 based upon user s capacity propulsion desired floor to seat height and selected front and rear wheels 24 2 3 1 24 amp 22 wheels The 24 610 mm and 22 550 mm wheels are only spoked wheels They can be delivered with pneumatic or solid tyre A flat tyre photo 21 must be removed in order to be repaired Remove the rim assembly tyre and inner tube repair or replace the inner tube reinsert in the tyre and reposition the assembly on the rim Comply with the inflation pressure specified on the sidewall of the tyre Note remember that in order to maintain the interchangea bility of the chair wheels equipped with quick release axles the pressure in the two tyres should be the same A Check and adjust the brakes to ensure they are still correctly positioned and function as required Ainsa exceed the pressure specified on the sidewalls of the tyre otherwise the tyre may explode and cause injuries Pneumatic tyres wear out In addition the roughness of the ground surface and driving have an impact on their longe vity Replace them regularly
36. tion of the attachment labels 2 Tighten the straps C Posture belt The posture posture belt is mounted on the back frame picture 24 2 Check that the posture belt on the wheelchair is correctly fastened If posture belt on the wheelchair is missing we recommend that the user should transfer to the seat of the vehicle if possible The posture belt should be used in addi tion to but never as a substitute for an approved passenger restraint system 3 point belt D Fastening of 3 point belt vehicle safety belt device Although all three points may be anchored to the vehicle floor the diagonal belt passing over the users shoulder should be routed through a point above and behind the seated user which is fixed to the vehicle sides before passing down to the floor The 3 point belt should not be kept from the user s body by the parts of the wheelchair 13 14 e Summary of warranty terms 5 1 Standard Invacare terms and conditions This is to certify that your manual wheelchair is warranted by Invacare for a period of 2 years for the frame and cross bars all others parts 2 years also but subject to the following conditions If a defect or fault is discovered the supplier dealer from whom the appliance was purchased should be notified imme diately The manufacturer will not accept responsibility for damage caused by misuse or non observance of the instructions set out in the user manual During the p
37. tion should be conform to the scheme enclosed with each belt delivery the belt should be mounted and adjusted by your regular dealer Make sure that the belts do not get caught in the spokes of the rear wheel Ensure you are sitting correctly i e fully back in the seat and the pelvis is as upright and symmetrical as possible not forward on one side or tilted back Position the posture belt so that the hip bones can be felt above the belt As a guide adjust the length so that there is just sufficient room for your hand to slide between your body and the belt The posture belt must not be used as a 3 point belt in a car Safety optional equipment Anti tippers with tipping lever photo 36 prevent back tipping which ensures safety when using a reclining backrest driving on slopes or crossing obstacles It is height adjustable and also act as tipping lever see paragraph Tipping lever Anti tippers can remain in place when the wheelchair is not used perform a half turn by activating the button A schema 38 to its indexing AN ua recommended distance between anti tippers small wheels and floor is 3 to 5 centimetres this adjustment is required with reference to the position and diameter of the rear wheel Push down the button A schema 37 and adjust the wheels holding tube for the desired distance based upon the preset holes AN Make sure that the dog points locates in and protrudes through its appropriate location hole
38. to avoid trouble caused by puncture Please consult with your Dealer 2 3 2 Handrims They provide the wheelchair propulsion They can be made of anodized aluminium or coated with nonslip plastic optional Nai are constantly in contact with your hands Make sure that they are not damaged 2 3 3 Axles The axles connect the wheels and frame photo 22 Fixed 12 transit only and quick release axles are available Fixed axles regularly check the axle tightening Quick release axles photo 23 depress the button A and insert the axle in the wheel hub Position the assembly in the bearing B of the multiple adjus table wheel mounting until it locks in place The locking balls C must rise above the bearing No significant side clearance is allowed To reduce clearance as much as possible remove the axle and adjust the nut using a 19 mm key then block the axle with an Imm open end key ZA Male sure that the axle and the locking balls are clean wipe out every month with a rag soaked with fine oil To prevent falls it is essential that the button A and the locking balls C are disengaged providing a perfect lock of the rear wheels The quick release axle is a precision part take care of shocks and clean regularly to ensure the good working of the mechanism 2 4 Castors 2 4 1 8 6 amp 5 wheels The front wheels are available in 8 200mm diameter and in two widths 3 8 32 mm and 2 5
39. user determines the rearward stability and also the ease by wich the user can propel the wheelchair using the handrims They are mounted on the multiple adjustment wheel support brackets e The castor consists of the front wheel and the fork The castors provide front contact with the ground and determine the steering by the direction of the forks e The manual brake is a parking brake The two manual brakes are used to secure the wheelchair when stationary Armpad Backrest upholstery Armrest Backrest 16 Rear wheel Seat upholstery Rear wheel Swing away support legrest Rear wheel axle Adjustable footrest tube Handrim p Manual Footplate brake p Folding f pd Swing away Steering tube footrest Front wheel 2 Adjustments 2 1 Seat 2 1 1 Seat upholstery Standard seats Nylon upholstery seat with or without Velcro fastener the Velcro fasteners are required for the proper positioning of the cushion photo 1 please make sure that the cushion is properly positioned on the seat e Padded seat it provides comfortable support to the user Standard seats are not adjustable in the event that they become slack it is recommended to request your dealer to replace them A Always use upholstery equipped with Velcro fasteners when you have a cushion in order to prevent sliding Adding a cushion to the seat will raise your height above the ground and can affect your stability
40. w D bring to new position and firmly tighten the screw D A Take care of the stability by using elevating legrests and reclining backrests on the same chair Lowering the legs before raising the backrest could make the wheelchair unstable Do not place anything heavy or let children sit on the legrest It may cause damage to the mechanism The distance between the lowest part of the footrest and the ground must be at least 40 mm Footrests photos 12 amp 13 the footplate can be lifted during transfers footrests are height adjustable and can be equipped with a fixed or articulated footplate optional Loosen the screw A to adjust to the desired height firmly tighten the screw after adjustment The footplate can be articulated by indexed plate optional loosen the screw B adjust to the desired angle and tighten securely Straps to ensure a good position of the feet two types of straps can be provided the heelrest strap plain or adjustable by Velcro fasteners and the calfpad strap attached to the footrest support are both adjustable by Velcro fasteners Note the standard footrest supports and legrests are mounted in pairs on the wheelchair whenever you remove them remember that you have a right side and a left side ZING lift the wheelchair by the footrest supports or legrests Keep your fingers away from movable parts during folding disassembling or adjustment to prevent injuries 2 1 5 Armrest
41. wing pages PAN This is a warning symbol it is essential that the instructions in these paragraphs are followed in order to prevent personal injury to yourself and others around you D This is an information symbol about possibility to contact your Dealer for more information 1 2 General description see photo Your wheelchair is made of various parts and this manual describes only the main parts We recommend that you become acquainted with the following terms in order to better understand your wheelchair operation e The seat consists of the seat and backrest upholstery the backrest and armrests This unit is designed to provide optimal comfort e The swing away footrest support or legrest this is the supporting part between the frame and the footrest which swivels to facilitate transfers and can be removed during transport 15 e The footrest consists of an adjustable tube and the footplate which supports the foot e The folding frame consists of side frames and a folding system including the seat rails These parts constitute the frame which is the supporting component of the wheelchair and its strength is well tested checked at 125 kg and 160 kg for 50 5 55 5 amp 60 5 cm seat width e The steering tube is the connection between frame and castors it allows the adjustment of the seat angle e The rear wheel consists of the wheel axle and handrim The position of the rear wheels relative to the seated
42. ying the brakes Fold the footplate up and push the footrest legrest to the side remove swing away the armrest to falicitate the transfert Shift your body towards the place where you want to sit while distributing your weight to the arms and hands figures 8 amp 8A While moving from the wheelchair to the seat your body will have little or no support Where possible use a transfer board during transfers 2 2 Front transfert figure 9 If you are more or less able to stand up and if your upper body is strong and mobile enough you can transfer forward to another seat If you find this movement difficult we recommend that you obtain some assistance from an attendant or carer to ensure the transfer is as smooth and safe as possible Lock both brakes and ensure both castor wheels are facing the forward position Please note that the brakes should not be used in any case as support for transfers Fold the footplate up then grip firmly the armrest handle take care of your nails on the skirt guard edges Push on your arms to easily lift yourself up and the attendant can help you to finalise the transfer to the place where you wish to sit N Warning Position yourself as close as possible to the place where you wish to sit When transferring position yourself as far back as possible in the seat to prevent breaking screws damaging the seat upholstery or causing the wheelchair to tip forward Loc
Download Pdf Manuals
Related Search