Home

LC-151

1. optional terminal for end of line resistors connections Terminals 6 7 amp 8 Marked NC C NO These are the output relay contacts of the detector Connect to a zone input on the control panel When an intruder is detected alarm relays N C and N O will switch for 1 8 sec 7 1 Wire Size Requirements Use 22 AWG or larger wires Use the following table to determine required wire gauge and length 10 8 Settings amp Adjustments 8 1 Detection beam direction The LC 151 detection beam direction is fixed As a result it is recommended to face the intrusion area with the detector 8 2 Detection beam range setting The detection range may set by tilting the detector while installed using the LC B1 15X 15m 49ft 8 3 Sensitivity Adjustment The calibration of detector sensitivity is performed by a single sensitivity potentiometer and a Microwave intensity jumper Changing the PIR sensitivity and microwave intensity affects immunity to environmental noises and allows the detector to operate without nuisance alarms in noisier environments The microwave intensity jumper is marked with H high L low settings The sensitivity potentiometer is marked with to Position is the minimum sensitivity and position is the maximum sensitivity The PIR sensitivity and microwave intensity must be adjusted according to environmental conditions as follows Sensitivity Potentiome
2. European directives Low Voltage directive 2006 95 EC RoHS directive 2002 95 EC EN300 440 2 EN301 489 1 EN50130 4 A1 2 EN61000 6 3 A11 European standards requirements EN60950 1 EN50131 1 EN50131 2 4 EN50130 5 USA amp Canada RSS210 ICES 003 Protection Degree e Specifications are subject to change without prior notice FCC COMPLIANCE STATEMENT FCC ID F5309LC151 CAUTION Changes or modifications not expressly approved by Digital Security Controls could void your authority to use this equipment This equipment generates and uses radio frequency energy and if not installed and used properly in strict accordance with the manufacturer s instructions may cause interference to radio and television reception It has been type tested and found to comply with the limits for Class B device in accordance with the specifications in Subpart B of Part 15 of FCC Rules which are designed to provide reasonable protection against such interference in any residential installation However there is no guarantee that interference will not occur in a particular installation If this equipment does cause interference to television or radio reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Re orient the receiving antenna Relocate the alarm control with respect to the receiver Move the alarm control away
3. rc LC 151 Dual Tech Motion Sensor Single PIR amp Microwave with adjustable Pet Immunity INSTALLATION INSTRUCTIONS amp USER MANUAL P N 7131720 ver B c m 3 2 _ E 52 ASsSempiy 2 ccccancacaacensececcencecaccananendoancesncacneated nt veaseanicecsecninesseesncncscoencedsenesdocaasaaapao 4 2E i e uM D NEM einedessPaiiigiedis eite d Mtm 6 t il RT 8 7 6 ee nee UE 10 7 1 Wire Size eee ee 10 MES Suh amp AdUSIMENS Rm 11 8 1 Wr i veienBer laneis RETO 11 8 2 Detection beam range setting ccccccecceccsecceeceeeceeceeccueceecaeeceesueccuecuesaeeseeseeeseesensaeesas 11 8 3 DelSIUVITY Adjustment 11 OA 12 SECURE 14 VCSEL OCCU RR 14 ME codcm E 14 12 OOS elitum T I5 1 General The LC 151 is a unique motion detector utilizing a single two elements passive infra red element and Microwave technology for use outdoors in harsh environments The LC 151 is designed for outdoor use in the most severe and climatic conditions and may also accommodate pets with the addition of optional pet immunity lenses High reliability is achieved by combining both dual tech hardware with highly sophisticated software greatly reducing the possibility of false alarms Th
4. 12 When the LED jumper is in the ON position the LEDs will be active When the LED jumper is in the OFF position the LEDs will not activate Detection Control jumper Factory setting ON e Place the top cover to the base and close it using the bottom screw e Place the top visor in place 13 9 Operation Note Connect the LC 151 to a positive Voltage output of 9 6 16Vdc source Use only a listed power limited source The detector shall be provided with minimum of 4 hours of standby power from either a listed compatible control unit or power supply detector begins 30 second warm up period once connected to power Ifthe LEDs are enabled they will sequentially flash from left to right for the duration of the 30 seconds warm up period the warm up period is complete the detector is ready for use 10 Test procedure Walk Test IMPORTANT NOTE Once installed the unit should be thoroughly tested to verify proper operation and coverage After installation the unit should be tested annually by the installer The end user should be instructed on how to perform a weekly walk test Make sure LEDs control is set to ON Ensure the detector has completed the 30 second warm up period before walk testing Make sure that the protected area is cleared of all people Create motion in the entire area where coverage is desired by walking perpendicular to the detection pattern Look at the LEDs wh
5. from the receiver Connect the alarm control into a different outlet so that alarm control and receiver are on different circuits If necessary the user should consult the dealer or an experienced radio television technician for additional suggestions The user may find the following booklet prepared by the FCC helpful How to Identify and Resolve Radio Television Interference Problems This booklet is available from the U S Government Printing Office Washington D C 20402 Stock 004 000 00345 4 INDUSTRY CANADA COMPLIANCE STATEMENT 1C 160A LC151 The term IC before the radio certification number only signifies that Industry Canada technical specifications were met This Class B digital apparatus complies with Canadian ICES 003 Cet appareil num rique de la classe B est conforme la norme NMB 003 du Canada 15 47CFR part 15 subpart C section 15 245 47CFR part 15 subpart B IEC 60529 IP 65 RTTE Compliance Statement DSC erkl rer herved at denne komponenten overholder alle viktige krav samt andre bestemmelser gitti direktiv 1999 5 EC Poreste meio aDSC declara que este equipamento esta em conformidade com os requisitos essenciais e outras determina es relevantes da Directiva 1999 5 EC DSC bekr ftar h rmed denna apparat uppfyller v sentliga kraven och andra relevanta best mmelser i Direktivet 1999 5 EC Con la presente la Digital Security Controls dichiara che questo prodotto co
6. utilizing microwave movement detection combined with a PIR detection beam An intrusion is defined by the PIR detection beam being crossed and a microwave detection occurring causing an alarm No alarm will be generated if only the PIR detection beam is crossed or if only a microwave detection occurs 5 Selecting mounting location The installation of the LC 151 requires a solid level base for the mounting bracket and must be located in a manner that when the detector is mounted it is facing the center of the desired detection zone It is recommended that the detector will face a solid border limiting the detection area such as the building structure or fencing wall to avoid undesired detection range The protected area must be free from obstacles like walls fences trees ditches and other microwave detectors Choose a location most likely to intercept an intruder according to detection pattern on page 5 Avoid the following Installation Locations e Facing direct sunlight e Facing areas subject to rapid temperature changes e Mounted at more than 10 from the vertical or horizontal plane e Facing metal doors e Near direct sources of heat or airflow e Clear all physical obstacles from the detection area e g plants laundry etc e Clear all light reflecting surfaces from the detection area including puddles or other standing water e Avoid installation on the following types of ground Thick veg
7. ain small animals removal of top cover and removal from mounting bracket Assembly description The LC 151 is a robust yet small detector which includes a large LED indicator that can be easily observed from long distances to provide indication of intrusion Using the supplied mounting bracket the LC 151 can be easily mounted to walls using the provided mounting screws For installations requiring the detection beam to be adjusted horizontally or vertically to obtain the desired field of protection use the LC B1 15X Outdoor Mounting Bracket pictured below not included LC 151 Outdoor Motion Detector LC B1 15X Outdoor Mounting Bracket The LC 151 consists of two detection elements e PIR element e Microwave element The following drawing shows all internal elements Microwave Doppler Detection LEDS Microwave intensity control jumper Detection LED control jumper Factory setting ON Factory setting ON Sensitivity setting Tamper switch Terminal Connection Block 4 Detection Pattern The LC 151 has a 90 top view PIR and MW detection pattern with over 15m 49 ft detection distance when installed at 2 4m 7 8 ft above the ground surface Standard Lens TOP VIEW 10 5m 34 5ft 10 5m _ 34 58 2 4m 8 71 LC L1 15X Corridor Lens sold separately TOP VIEW 14m 14 6 SIDE VIEW The LC 151 can differentiate between pets and human bodies and alert accordingly by
8. e active elements are comprised of a single two elements PIR and advanced Microwave detector inside a stylish rigid plastic body These special optics combined with a Microwave Doppler sensor assures elimination of false alarms while maintaining high security standards for the detection of human intruders into the protected area The detection sensitivity and range is controlled by a potentiometer allowing fine tuning so that the correct detection pattern will be set for every installation The LC 151 is designed to protect large areas and can easily be installed on walls in order to provide a solid protection of the area while rejects interferences from birds and small animals due to the optional PET MASK optics 2 Features e Microwave detection based on Doppler concept e amp N C relays switched at the same time e Installation height is calibration free from 1 8m to 2 4m 5 9 to 7 8 ft e Pet Immune up to 15kg 33lb without pet immunity lens or up to 36kg 80lb when using supplied LC F1 15X pet immunity lens e PIR sensitivity adjustment e MW intensity selection e Temperature compensation e Microcontroller signal processing e Front and back tamper protection e Unique waterproof and sealed plastic design e Detection Range Up to 15m 49 ft e Detects human intruders walking or running e No maintenance required e High RFI EMI Immunity e Protection from direct sunlight wind up to 30 m sec 98 ft sec snow and r
9. enever motion is detected all LEDs are turned ON Allow 5 sec between each test for the detector to stabilize Walk across the entire area where coverage is desired Should the coverage be incomplete readjust sensitivity or relocate the detector Once coverage is as desired the LEDs should be disabled 11 Accessories Part Number Outdoor Mounting bracket LC B1 15X PIR Corridor Long Range Lens LC L1 15X 36kg 805 PET Filter LC F1 15X 14 12 Specifications Detection Method PIR AND MW Microwave Frequency X band 9 9GHz 10 525GHz 10 687GHz Power Input 9 6 to 16Vdc EN Current Draw Active 24mA 5 Standby 21mA 5 Temp Compensation Dual slope temperature compensation Alarm Period 2 sec 0 5sec Form C NC NO Common 28Vdc 0 1 A with 10 Ohm Two Switches Alarm Outputs Tamper Switch s Warm up Period N C 28Vdc 0 1 A with 10 Ohm Series protection resistors Opens when cover is removed from unit s base or if base is removed from wall 30sec 5sec Green LED for PIR detection Yellow LED for Microwave detection Red LED for alarm condition All LEDs are ON during ALARM LED Indicator RF Immunity ElectroStatic Immunity Transient Immunity Operation Temp Dimensions Weight 10 V m plus 80 AM from 80 MHz to 2GHz 6kV contact 8kV air 35 C 450 C 31 F 131 F 160 mm x 70 mm x 45 mm 6 3 x 2 7 x 1 7 210gr 0 45 Ib RTTE directive 1999 5 EC EMC directive 2004 108 EC
10. etation Grass un mown Water Sand and Metal NOTES e Recommended installation height is 2 1m 6 8 ft e The PIR sensor detects motion crossing the beam it is less sensitive detecting motion towards the detector The LC 151 performs best when provided with a constant and stable environment e In order to ensure suitable operation of the LC 151 the type of ground should be one of the following Asphalt concrete Cement Soil Clay Gravel or Grass mown Sensitivity adjustment may be required upon extreme temperature changes Extremely high temperature will reduce detection range Extremely low temperature will increase detection range Choose proper installation location to avoid resetting 6 Detector Installation Important Prior to installation read both Operation and Selecting the mounting location sections carefully 1 Install the detector in such manner that the intruder is 2 The detector is to be installed at height of 1 8 to 2 4 most likely to cross the detection area from side to side meters 5 9 to 7 8 ft ideally 2 1m 6 8 ft 1 8 2 4 meters 3 Make sure to attach the metal bracket to a leveled 4 Placing the detector on perpendicular wall is straight and firm wall leaving 10cm 3 9 inches from required for guarding a side window opening the top and 10cm 3 9 inches from both sides for easy Alternately the LC B1 15X Outdoor Mounting bracket installation and maintenance can be instal
11. led on the same wall allowing the detector beam to be rotated towards the window 6 Release the rear metal bracket by unwinding internal bottom screw 7 Release the detector body from the metal bracket by 8 Attach the rear bracket to the wall using mounting pulling the detector up and out screws 9 Insert wires through provided access hole and wiring 10 Attach the sealing sponge pad to the wire opening channels from the rear side after the wires have been connected and prior to final product affixing to the mounted bracket 11 Place the detector on the mounting bracket from top 12 If Pet immunity up to 15kg 3316 is desired do not side down and then lock the screw at the bottom install the LC F1 15X mechanical pet filter If Pet immunity up to 36kg 8010 is desired install the LC F1 15X mechanical pet filter 7 Terminal Block Connections Terminal 1 Marked 12 Connect to a positive Voltage of 9 6 16Vdc source usually from the control panel Terminal 2 Marked GND Connect to the ground of the control panel Terminals 3 8 4 Marked TAMPER Tamper function is required connect these Terminals to a normally closed 24 Hour Tamper Zone on the control panel If the top cover of the detector is opened or the detector is detached from installation wall an immediate alarm signal will be sent to the control panel Terminal 5 Marked EOL End of line
12. nforme ai requisiti essenziali ed altre disposizioni rilevanti relative alla Direttiva 1999 05 CE Por la presente DSC declara que este equipo esta en conformidad con los requisitos esenciales y otros requisitos relevantes de la Directiva 1999 5 EC Hierdurch DSC dap dieses Ger t den erforderlichen Bedingungen und Vorrausetzungen der Richtlinie 1999 5 EC entspricht tow DSC nanvgr m aur avakrur riva copeosvr pr rus we OA Tus O nyiug 1999 5 Hierbij verklaart DSC dat dit toestel in overeenstemming is met de eisen en bepalingen van richtlijn 1999 5 EC Par la pr sente DSC d clare que cet article est conforme aux xigences essentielles et autres relevantes stipulations de la directive 1999 5 DSC vakuuttaa laitteen t ytt v n direktiivin 1999 5 EC olennaiset vaatimukset Hereby DSC declares that this device is in compliance with the essential requirements and other relevant provisions of Directive 1999 5 EC The complete amp TTE Declaration of Conformity can be found www dsc com intl rttedirect htm pu 10 525 GHz_ 10 687 GHz 99 Hz ON Sac UR ARA is SI SOAS Ru bz QUK XO i 8 RU Pun Wo me e P wm wr a be SE be Yes nc pA LM LLL AA AERA
13. ter MW intensity setting 11 Environment type Potentiometer position MW position Risk Between positions and 4 High risk Between rene Ca 4 and 5 Very high risk Between positions and 4 Noisy area Between positions 2 and 3 Extremely Noisy area At position 1 Note Adjust sensitivity according to environmental conditions Low risk very stable environment without interference from parking garages parking space playgrounds football fields service roads etc e Risk Stable environment with some trees bushes flowerpots planters etc e High risk Unstable environment with different types of vegetation and grass and puddles e Very high risk Unstable environment with winds and small pets rats mice birds e Noisy area Unstable environment with vegetation and water sources like swimming pool lake canal weeds as well as small pets like cats and rabbits e Extremely Noisy area Very unstable environment subjected to wind snow rain with vegetation water and large pets like dogs For Example If the detector is used in a space which contains several bushes and a swimming pool the environmental conditions should be considered a Noisy Area 8 4 Indications setting The LC 151 has 3 LEDs that each points at different indication 1 Green LED indicates PIR detection 2 Yellow LED indicates Microwave detection 3 Red LED Indicates an alarm logic AND of both Mircowave and PIR

LC-151

Contents

Download Pdf Manuals

Related Search

Related Contents