user manual
Contents
1. You can charge your device by using USB cable or adapter 1 Insert the charger lead carefully 2 The plug only fits one way Do not use excessive force to insert the plug KD Your device supports three working modes For the client we only use PC or laptop as the example in this document USB Mode Connect to the device with the USB cable Mixed Mode Connect to the device with the above two connection methods Notes If you want to connect to the Internet by using Wi Fi mode make sure that the client supports the Wi Fi function The following picture is the application example All of the client devices can surf on the Internet at the same time Via USB Cable 1 Connect your device and the client with the USB cable 2 Power on your device 3 Follow the system prompts to complete the software installation Notes e Ifthe system does not launch installation automatically you can run the installation program in path of My Computer gt Mobile Hotspot The driver of your device will be installed at the same time 4 After the installation the system will create a shortcut icon on your desktop and a Mobile Hotspot program group in the Start Programs menu The connection between your device and the client will be established successfully a moment later Via Wi Fi 1 Power on your device directly It will take 1 2 minutes to initialize 2 Use your normal Wi Fi application on the client to search the availabl2. C 35 C Storage temperature 20 C 50 C Charging temperature 0 C 45 C Humidity 5 95 Notes microSD mice is a trademark of SD Card Association The device s standby and working time are only for your reference and based on ideal working environment The following figure shows the appearance of the device it is only for your reference The actual device may be different Operate system Web Browser Left Side Bottom Right Side Interface and Buttons Hold the Power button to switch on off the device 2 Memory card slot It is where you insert the memory card microSD microSD card card This button is used to start end Wi Fi Protected Setup authentication process and enable disable the Wi Fi function e Hold it for 3 seconds to activate the WPS function When the WPS function is available press it to deactivate the WPS function Press it to enable disable Wi Fi function 4 LED Screen It indicates the signal type signal strength battery Wi Fi etc 5 External Antenna It is used to connect an external antenna to Connector enhance the signal strength e Charge your device a CliatgenTSe pan Connect the client to your device via USB cable Notes e Hold the WPS and Power buttons simultaneously until the LED screen turns off and then release the buttons The device will restart automatically and restore to the factory default settings e Please use the original e
3. gt SMS Settings Set the SMS configuration This function allows you to store contacts to your device or SIM card After logging in select PhoneBook and you can add a new contact in Add New tab and perform operations to the contact in the Device or SIM Card tab HIN Omo Name Phone number Mobile number Home number Nick name E mail Group Oh Jonna 12458 Common eat Delete es 14 If your client device supports WPS you need not to input the password manually after WPS has been available Please do the following 1 Start up your device 2 Launch the client device connected to your device 3 Enable the WPS function of your device 4 Enable the WPS function of the client Notes e Ifthe current security mode of the device is OPEN or SHARE the WPS function is useless e For the detailed operations about the client please refer to the client s instruction When you enable the Wi Fi function and use the battery to supply power to the device once no user connects to the device within 10 minutes the device will enter the sleep mode and the LED screen will be turned off In the sleep mode the Wi Fi function will be disabled Press Power or WPS button to wake up the device and the LED screen will be turned on Notes With USB connection if no Wi Fi user connects to the device within 10 minutes only the Wi Fi function will be disabled Press Power or WPS button to enable this function T
4. is Always On Notes You can browse the WebGUI Configuration page and click WAN Connection to set the WAN connection mode 10 1 Make sure the connection between your device and the client is correct 2 Launch the internet browser and enter http 192 168 0 1 or http ufi home in the address bar Notes It is recommended that you use IE 7 0 or later Firefox 2 0 or later Opera 10 0 or later Safari 4 0 or later Chrome 5 0 or later 3 The login page appears as follows The following figure is only for your reference Administrator M Login 3G Mobile Hotspot WAN Information WLAN Information Network Provider China Mobile SSO uFi 20000 Network Type EDGE a Channel Auto Connection Status Disconnected Security Level WPA PSK IP Address Gateway Address 192 168 0 1 Primary ONS Subnet Mask 255 255 255 0 Secondary ONS OHCP Server Enable Device Information Software Version BD_MF62V1 0 0804 Hardware Version MF62 1 0 0 PIN Status Disable View the information of WAN WLAN and Device Input the case sensitive default password admin and then click Login to access the WebGUI Configuration page Notes e Do not put anything on the top of your device Do not lay devices to overlap each other when using e The device takes 1 2 minutes to initialize and attach to the network 11 PIN Code Verification If the PIN code of your SIM card is enabled you will need
5. or in connection with using of this product whether or not ZTE had been advised knew or should have known of the possibility of such damages including but not limited to lost profits interruption of business cost of capital cost of substitute facilities or product or any downtime cost You can get help by e Sending E mail to mobile zte com cn e Visiting http www zte com cn e Calling Service Hotline 86 755 26779999 C E 1588
6. ZTE MF60 User Manual LEGAL INFORMATION Copyright 2013 ZTE CORPORATION All rights reserved No part of this publication may be excerpted reproduced translated or utilized in any form or by any means electronic or mechanical including photocopying and microfilm without the prior written permission of ZTE Corporation The manual is published by ZTE Corporation We reserve the right to make modifications on print errors or update specifications without prior notice Version No R1 0 ZTE CORPORATION NO 55 Hi tech Road South ShenZhen P R China Postcode 518057 Tel 86 755 26779999 URL http www zte com cn E mail mobile zte com cn 1 ZTE MF60 is a 3G 2G mobile hotspot device working in GSM GPRS EDGE WCDMA HSPA HSPA network The client devices could connect to it via USB or Wi Fi interface The device supports data and SMS services enabling you to communicate anytime and anywhere This manual provides instructions on how to install and get started with the product For information about connection of services please consult your service provider HSPA DL 21 6Mbps UL 5 76Mbps WCDMA CS ES oer UL DL WCDMA PS ES oer UL DL Data Service Dimensions WxHxD 99 6mm 54mm 14 6mm Windows 7 Windows Vista 32bit or 64bit Windows XP SP2 or later MAC 10 4 or later IE 7 0 or later Firefox 2 0 or later Opera 10 0 or later Safari 4 0 or later Chrome 5 0 or later Operating temperature 0
7. e wireless network Notes You need to check your Wireless Network Connection Set the client to obtain an IP address automatically in the Internet protocol TCP IP properties and the client will get an IP address like 192 168 0 100 3 Select the SSID of your device and then click Connect The following figure is only for your reference i Wireless Network Connection 2 Choose a wireless network Network Tasks i Refresh network list Click an item in the ist below to connect to a wireless network in range or to get more information Zh Set up a wireless network for a home or small office Related Tasks 4 Learn about wireless networking fe Change the order of preferred networks P Change advanced settings Notes There will be a pop up window to require the password Check the label on your device to gain the SSID and preset password information Please do remember the new password when you change the password by selecting Settings gt Wi Fi Settings gt Security after logging in the WebGUI Configuration Page You can restore the device to the factory default settings in case you forget it 4 Wait a moment the connection between your device and the client will be established successfully 1 Switch on the device 2 Establish a connection between your device and the client 3 After successfully establishing the connection access the Internet in the Always On and Manual mode The default mode
8. iolate related national regulations about telecom terminals Avoid using your device near or inside metallic structures or establishments that can emit electromagnetic waves Otherwise it may influence signal reception Your device is not waterproof Please keep it dry and store in a shady and cool place Do not use your device immediately after a sudden temperature change In such case it will produce dew inside and outside your device so don t use it until it becomes dry Handle your device carefully Do not drop bend or strike it Otherwise your device will be damaged No dismantling by non professionals and only qualified technicians can undertake repair work 16 e Operating temperature range of 0 C 35 C and humidity range of 5 95 are recommended Using Battery e Do not short circuit the battery as this can cause excessive heat and fire e Do not store battery in hot areas or dispose of it in a fire to avoid explosion e Do not disassemble or modify the battery e When not using the battery for a long period remove it from your device and store it in a cool dry place e Never use any charger or battery damaged or worn out e Return the wear out battery to the provider or put it in the appointed recycle place Do not put it in familial rubbish Warning If the battery is broken keep away from it If it taints your skin wash your skin with abundant fresh water and ask doctor help if necessary Limited Wa
9. ngs After logging in select Settings and you can do the following operations Select Settings gt View the Wireless Information select Band Selection 3G Settings Mode and change APN Setting View the current station list change the basic wireless network settings choose security mode and WPA type and perform the WPS configuration Select Settings gt Wi Fi Settings Select Settings gt Set the Mac IP Port Filtering Port Forwarding or the Firewall System Security configuration View the current status of your device change the Administrator Settings restore factory defaults manage PIN or set the LAN interface configuration Select Settings gt Advanced Notes Make sure that you can remember the new password if you change the login password by selecting Settings gt Advanced gt Management Please restore the device to the factory default settings in case you forget the new password 13 1 Log in the WebGUI Configuration page and select WAN Connection 2 Select Manual gt Disconnect Internet 3 Click Apply Notes Turning off the device can also terminate the internet connection This function allows you to view send and receive short messages After logging in select SMS and you can do the following operations Select SMS gt Device Operate the SMS in your device Select SMS gt SIM Card Operate the SMS in your SIM card Select SMS gt New Message Send or save SMS Select SMS
10. o the Owner e Some electronic devices are susceptible to electromagnetic interference sent by your device if inadequately shielded such as the electronic system of vehicles Please consult the manufacturer of your device before using if necessary 15 Operating your device may interfere with medical devices like hearing aids and pacemakers Please always keep them more than 20 centimeters away from such medical devices when they are turned on Turn your device off if necessary Consult a physician or the manufacturer of the medical device before using your device Be aware of the usage limitation when using your device at places such as oil warehouses or chemical factories where there are explosive gases or explosive products being processed Turn off your device if required The use of electronic transmitting devices is forbidden in aircrafts at petrol stations and in hospitals Please observe and obey all warning signs and switch off your device in these conditions Do not touch the inner antenna area if not necessary Otherwise it will affect your device s performance Store your device out of the reach of little children Your device may cause injury if used as a toy Do not touch the metallic parts of your device so as to avoid a burn when your device is working Using Your Device Please use original accessories or accessories that are authorized Using any unauthorized accessories may affect your device s performance and v
11. rranty e This warranty does not apply to defects or errors in the Product caused by i Reasonable abrasion ii End User s failure to follow ZTE s installation operation or maintenance instructions or procedures iii End User s mishandling misuse negligence or improper installation disassembly storage servicing or operation of the Product iv Modifications or repairs not made by ZTE or a ZTE certified individual v Power failures surges fire flood accidents actions of third parties or other events outside ZTE s reasonable control vi Usage of third party products or usage in conjunction with third party products provided that such defects are due to the combined usage vii Any other cause beyond the range of normal usage intended for the Product 17 End User shall have no right to reject or return the Product or receive a refund for the Product from ZTE under the above mentioned situations e This warranty is End User s sole remedy and ZTE s sole liability for defective or nonconforming items and is in lieu of all other warranties expressed implied or statutory including but not limited to the implied warranties of merchantability and fitness for a particular purpose unless otherwise required under the mandatory provisions of the law Limitation of Liability ZTE shall not be liable for any loss of profits or indirect special incidental or consequential damages resulting from or arising out of
12. to input the PIN code when you login at the first time Vertty PIN PIN Apply Notes The SIM card will be locked if you enter wrong PIN code consecutively for three times If you want to modify the PIN Status please select Settings gt Advanced gt PIN Manage to do the actions Advanced gt PIN Management Status Management Restore PINManagement Router PIN Management PIN Status Action Enable v PIN Remaning tmes 3 Quick Settings After logging in select Quick Setup and then the Quick Setup wizard appears re Settings 1 6 The wizard will show you how to set up your gateway in the safe way Click Next to continue click Back and Nexto navigate and click Apply to save the settings Notes Basic parameters can be set in this wizard For advanced parameters you need to set them in other menus Next The Quick Settings wizard guides you how to set the basic parameters for your device in the safest way After this procedure you can use your Internet service Notes The parameter settings may have been preset by your service provider and you will enjoy your Internet service directly Please contact your service provider for details if you want to do some modification WAN Connection After logging in select WAN Connection and you can choose the WAN Connection Mode according to your requirement WAN Connection Mode e WAN Connection Status Disconnected i Setti
13. xternal antenna if necessary LED Indicator When the device is powered on the following icons will appear on the LED screen with the corresponding indicates listed in the table below Network signal strength 2G Network type 2G or 3G icon will appear on the LED screen according to the network being connected Connect to the Internet automatically M Connect to the Internet manually Roaming network indication New message received Wi Fi Status and number of the connecting users Battery power indication Inserting SIM Card and Battery 1 Slide the back cover and remove it 2 Insert the SIM card into the SIM card holder 3 Insert the battery as shown with the contacts located against the metal springs and press the battery down into the case A A LA ee LB r Z he se Ka Dog I gt ee 5 Y Z Na A o IA an SB 4 Slide the back cover and lock the cover in its place Inserting microSD Card 1 Pull the microSD cover out of the card slot Notes Do not pull the cover rudely as it is connected with the device 2 Insert the microSD card into the microSD slot The following picture shows the correct inserting direction You will hear a click when the microSD card locks in uae 3 Close the microSD cover Switching On Off Your Device Hold the Power button to switch on off the device Notes The device is powered on when the LED screen lights up Charging Your Device
Download Pdf Manuals
Related Search