User Guide
Contents
1. eye protection when using tools to install repair or adjust door or operator to prevent eye injuries Before installing receiver disconnect all power to door operator to prevent unintended operation Disconnect all power to the electrical outlet the Receiver will be plugged into Do NOT connect this Receiver to a power source until instructed to do so Do NOT reconnect power to the door operator until instructed to do so Keep fingers and other body parts away from all moving parts of the door operator system while the system is being operated The door safety beams must be in working order and must not be obstructed during the programming steps WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK DO NOT EXPOSE THIS DEVICE TO RAIN WATER OR WET LOCATIONS NEVER LET CHILDREN OPERATE OR PLAY WITH DOOR CONTROLS KEEP REMOTE CONTROL AWAY FROM CHILDREN ALWAYS KEEP MOVING DOOR IN SIGHT AND KEEP PEOPLE AND OBJECTS AWAY UNTIL DOOR IS COMPLETELY CLOSED NO ONE SHOULD CROSS THE PATH OF THE MOVING DOOR A NEVER GO UNDER A STOPPED PARTIALLY OPEN DOOR IMPORTANT SAFETY INSTRUCTIONS Read these instructions Keep these instructions Heed all warnings Follow all instructions Do not use this apparatus near water Clean only with dry cloth Do not install near any heat sources such as radiators heat registers stoves or other apparatus including amplifiers that produce heat 8 Do not defeat the safety purp2. ASPIRERP WIRELESS CONTROL SYSTEM Garage Door Opener Conversion Module CAT RFUGR Designed to allow you to use your in vehicle transmitter with any garage dooe opener User Guide A Step by Step Guide for Installing and Operating the Garage Door Opener Conversion Module P COOPER Wiring Devices Your Conversion Module is designed to allow you to use your in vehicle transmitter with any garage door opener Simply follow the instructions to connect it to the wired accessory terminal block of your garage door opener then finish by following the easy programming steps Important Notice Read the enclosed instructions carefully before installing the Conversion Module Pay close attention to all warnings and notes This manual should be retained for future reference Table of Contents Package Coments indse oE Warnings Set up Operation Regulatory Compliance e esesesssssssesesresesesereseses Package Contents User Screw Conversion 6 ft Twin Guide 6 32 x 3 4 Module Lead Wire INSTALLATION SAFETY PRECAUTIONS WARNING INCORRECT INSTALLATION CAN LEAD TO SEVERE OR FATAL INJURY FOLLOW THESE INSTRUCTIONS CAREFULLY Before installing this receiver read the door operator s user guide fully so you are aware of all of the unit s functions and features A Wear protective gloves to install repair or adjust door or operator to avoid injuries Wear
3. Opener Conversion Module provided that it has not been subject to abuse improper installation or improper use and is returned prepaid to Cooper Wiring Devices Quality Control Department at 203 Cooper Circle Peachtree City GA 30269 If the product has been discontinued replacement will be made with the nearest available equivalent model This warranty does not cover consumables such as fuses Proof of purchase in the form of a bill of sale or receipted invoice that shows that the item is within the applicable warranty period must be presented to obtain the repair or replacement provided by the warranty Repair or replacement as provided under this warranty is the exclusive remedy of the customer Cooper Wiring Devices shall not be liable for any incidental or consequential damages for breach of any express or implied warranty on any of its products Except to the extent limited or prohibited by applicable law any implied warranty of merchantability or fitness for a particular purpose on this product is limited in duration to the duration of this warranty Some states do not allow the exclusion or limitation of incidental or consequential damages or allow limitations on how long an implied warranty lasts so the above limitations may not apply to you This warranty gives you specific legal rights and you may also have other rights which vary from state to state P l COOPER Wiring Devices IN U S A IN CANADA Importado por Cooper Wiring Devices Coo
4. cator Program button Red indicator turns ON Helpful Hint A broom handle can be used for depressing the button Step 2 Press and Hold for 1 second Button 3 on your in vehicle transmitter Button 3 Step 3 Press and release Button 3 on your in vehicle transmitter once more to operate the door Caution Door will move if operation is successful Note 1 To program your in vehicle transmitter Buttons 1 or 2 please see your vehicle s owners manual for instructions on programming with rolling code receivers Poma Note 2 A maximum of 8 transmitters can be programmed to the Conversion Module All transmitters programmed after the 8th transmitter will replace the 8th transmitter Use the following procedure to reset your Conversion Module This operation will remove all transmitters programmed to this Module Program Button 1 Plug the Conversion Module into an appropriate AC outlet Red 2 Press and hold the program button for 10 seconds The Red Indicator Indicator will flash 3 times to indicate a successful reset FCC and IC Statement FCC Regulatory Information NOTE This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not ins
5. ing flange hole is aligned with the outlet cover plate Provided screw hole 5 Install the screw provided through the Conversion Module mounting flange into the outlet and tighten screw Be careful not to overtighten 6 Connect one end of enclosed twin lead wires to the Garage Door Opener push button terminals These terminals are typically labeled Connect Leads P B and COM o x to Terminals Hint Connect to the same two terminals used by your existing wall control P B COMOBS Also see your Garage Door Opener owner s manual for specific wiring instructions If you need to purchase more wire use only 22 AWG or larger CL2X or better wire Connect Leads 7 Connect the opposite end of the twin lead wires to the Conversion fo Terminals Module s relay terminals 8 Fasten the twin lead wires to the wall or operator support structure so that it cannot become entangled with the Garage Door Opener during operation 9 Straighten the Conversion Module antenna wire and position it in the most vertical position allowable DO NOT CUT ANTENNA WIRE Uncoil Antenna and Position Vertically 10 Turn on power to the Garage Door Opener AC circuit and turn on power to the AC outlet the receiver is plugged into Program Button Use the following procedure for programming your transmitter to the Conversion Module Red Step 1 Go to the Conversion Module and press and release its Indi
6. ose of the polarized or grounding type plug A polarized plug has two blades with one wider than the other A grounding type plug has two blades and a third grounding prong The wide blade or the third prong are provided for your safety If the provided plug does not fit your outlet consult an electrician for replacement of the obsolete outlet 9 Refer all servicing to qualified service personnel Servicing is required when the apparatus has been damaged in any way such as power supply cord or plug is damaged liquid has been spilled or objects have fallen into the apparatus the apparatus has been exposed to rain or moisture does not operate normally or has been dropped NOORON gt Installation Safety Precautions 1 Make sure Garage Door Opener has been properly installed in accordance with unit s user guide 2 Test and confirm proper operation of the Garage Door Opener before proceeding with the installation of this receiver Installation 1 Turn OFF power to the Garage Door Opener before proceeding 2 Turn OFF power to the AC outlet the Conversion Module will be plugged into before proceeding Note This could be the same outlet as in step 1 K A vA fq o 3 Remove the screw that attaches the outlet cover plate Y Note Do NOT remove the cover plate A y Remove Screw 4 Plug the Conversion Module into the AC outlet positioning it so that Insert Screw the screw mount
7. per Wiring Devices si se vende en M xico 203 Cooper Circle 5925 McLaughlin Road Industrias Royer S A de C V Peachtree City GA 30269 Mississauga Ontario L5R 1B8 Tres Anegas 404 866 853 4293 800 267 1042 Col Nueva Industrial Vallejo Made in China Fabrique en Chine C P 07700 M xico D F 01 5747 4519 Hecho en China www cooperwiringdevices com AspireRF RFUGR1 PTA REV A
8. talled and used in accordance with the instruction may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try and cor rect the interference by one or more of the following measures a reorient or relocate the receiving antenna b increase the separation between the equipment and receiver c connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help IC Regulatory Information This Class B digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation of the device WARNING Changes or modifications to this receiver not expressly approved by Cooper Wiring Devices could void the user s authority to operate this equipment Warranty YOUR COOPER WIRING DEVICES ASSEMBLED PRODUCT ONE YEAR LIMITED WARRANTY For a period of 1 year from the date of purchase Cooper Wiring Devices will replace or repair the Garage Door
Download Pdf Manuals
Related Search