Is hear - Explona
Contents
1. t be placed as an unsorted municipal waste it must be collected separately DC 10 40V MAX 5W CE NH We reserve the right to change specifications without prior notice All trademarks are the property of the respective owners and are used for information purpose only Copyright by explona Devel Team explona repeater mini f1 00 User manual version 12. both fastenings from one side simultaneously It may compromise the leak proof All fastenings should be tighten after mount explona is specifically sealed to be leak proof e Opening of the device breaks the seal and voids warranty 5 3 Electrical installation Power supply should be protected with a 3A to 5A fuse The wiring should be connected according to the drawing on the next page Wire connections e brown GND ground e yellow 12V power supply after ignition dedicated switch explona doesn t have its own switch explona repeater mini f1 00 User manual version 1 4WeOUN5GY www explona com e green SPEED speed signal e white external switch connecting to the ground e grey connection to main tripmeter or external GPS receiver Connection of explona repeater to the main explona tripmeter are presented in the user manual of the main unit 5 3 1 Connection of the speed signal explona repeater mini can be directly connected to vehicles equipped with electrical speedometer or reed switch sensor If vehicle has an electrical speedometer vehicle speed signal VSS from car s wiring should be found It can be accomplished with the use of voltmeter When the ignition switch is turned on and car is moving the voltage on speed signal should vary periodically e g 0 i 12V or 01 5V If reed switch sensor is used one of its contacts should be connected to the SPEED wire and the other to th
3. e ground If the car is equipped with mechanical speedometer or has no speedometer at all it is necessary to use additional connection module That module can accept signal from turn converter or sensor mounted near wheels The calibration should be performed after installation of the device o explona repeater mini f1 00 User manual version 1 MeUNDSGY www explona com any GPS receiver speed impulse connection es 2 Schematics of explona mini connections White reset change of display L Gray connection of NMEA signal Green speed impulses 5A fuse explona Yellow power supply BOO Ignition switch version explona repeater mini f1 00 User manual WEONOGY www explona com 6 Technical data External dimensions mm enclosure 110x60x32 with fastenings 145x75x40 Enclosure aluminum black Ingress protection IP65 dust tight protected from water jets Display red LED display with 7 brightness steps can be turned off anti reflex coating Weight 300g Operating voltage 10 40V DC Power consumption max 5W Temperature range 20 70 C Distance resolution 10m Maximum distance 999 9 km NMEA interface RS232 8N1 4800 7 Rating plate BARDOA REE EA explona No user serviceable components inside Made in EU Poland www explona com The disposed device mustn
4. explona WeoONsaGey www explona com explona repeater mini User manual mt 3 explona repeater mini is the smallest device of explona family It was designed mainly as an additional display for a driver It can show data supplied by main odometer e g explona dakar Additionally it can serve as a standalone simple odometer In this mode it measures distance speed and voltage of the battery When any GPS receiver with NMEA signal is connected display can show current course as well Its aluminum enclosure is waterproof and protects against various environment conditions In every light condition the readings are clear thanks to big LED display with brightness regulation The display can be turned off if needed The device has a quick recall of the distance reading from every other display mode 4WeOUNSGY www explona com You should calibrate the device after installation and each change of tyres see chapter 4 Imprecise measurements can occur otherwise The device is supplied not calibrated which is show by blinking Cal Err on display 1 Features of explona repeater mini e two functions in one the device can be external display for the driver repeater mode showing data from main unit or it can be a standalone tripmeter mini mode depending on availability of data from master unit e 7 steps of brightness the display can be turned off completely e features of the repeater mode O O O O disp
5. he brightness of the repeater Decreasing the brightness below the minimum level turns off the display It is shown by a single dot All measures are continued but the keyboard is inactive to prevent accidental changes The up key turns the display on In case of data loss from main unit the device automatically switches to standalone tripmeter mini mode and continues to measure the distance uninterrupted This switch is indicated by blinking display It must be confirmed by pressing any key before normal functions can be operated recommended so the device can work correctly after the data loss from In the repeater mode the calibration is not required However it is main unit 3 Mini mode In the mini miniature tripmeter mode the device measures distance speed and voltage of the battery If any GPS receiver with NMEA signal is connected it shows current course as well A value to display is chosen by pressing and holding the red button or external key the description of the current reading will start blinking Each next press will change the displayed value in cycle distance trip speed SoG gt voltage Accu course CoG Pressing red button or external key shortly resets the distance If the distance is not shown on the display it will be recalled after the first press After that the second press will reset it In order to identify quickly the reading the following distinction was made e di
6. lay of data from main explona tripmeter e g dakar keyboard or external key selects the reading ability to follow brightness of the main unit if requested in case of data loss from main unit the device automatically switches to standalone tripmeter mini mode and continues to measure the distance uninterrupted e features of the mini mode O O O distance trip and speed measurements based on wheel turns measurement of a voltage of the main battery compass current course when any GPS with NMEA is connected fast recall of the trip display ability to connect external reset switches easily distinguished readings non volatile memory 2 Repeater mode In a repeater mode the device displays basic readings of a main tripmeter Red button or externally connected switch is used to change the shown value distance trip speed SoG course CoG The driver can change easily the display on his own if the external switch is mounted on the steering wheel Any number of external switches can be connected This way the pilot explona repeater mini f1 00 User manual version tWeOUNSGY www explona com can also change the display for the driver To single explona tripmeter up to 3 repeaters can be connected The up and down keys change the brightness of the display Pressing both keys simultaneously activates brightness follow mode In this mode a change of brightness on main unit also changes t
7. stance value with a dot e speed value without dot e voltage u at the end e course three digits with a degree sign at the end Brightness is changed as in repeater mode explona repeater mini f1 00 User manual version tWeOUNSGY www explona com 4 Calibration Calibration is the process of determining the number of pulses per Ikm or 1 mile of the travelled distance This is necessary to accurately measure the distance Calibration should be performed after installation and after each change of tyres The device is supplied not calibrated which is show by blinking Cal Err on display The calibration constant K should be in range 400 65535 Performing the calibration requires a reference section of road The length of the section should be 1km or Imile depending on the choice of units The more precise section will result in more precise tripmeter measurements The selected section of road can be e reference section of measuring authorities e distance between road markers e measured by correctly calibrated other tripmeter e measuring tape although a lot of patience is required The calibration procedure 1 turn off the power 2 press and hold red button and turn the power on 3 after a few seconds old K constant will be shown release the red button 4 position your car at the beginning of the section press red button shortly to reset the number of impulses A drive entire section stop e
8. xactly at the end press and hold red button the calibration constant will be stored and the device will return to regular mode Watch periodically the displayed number of impulses If it remains constant during motion then the speed connection or speed converter should be checked If calibration constant K is known e g it was determined previously for give set of wheels and car it can be set manually using up and down keys This manual mode is helpful also to make small adjustments if previous value gives constant over understated results explona repeater mini f1 00 User manual version 1 WeOUNSGY www explona com 5 Installation The device must be installed in a safe way It should not endanger health of driver and passenger during both regular work and accident In particular it mustn t obstruct the airbags The installation can be performed in an authorized garage Current list of authorized garages is available on the website www explona com 5 1 Contents of the set The set consists of 1 explona repeater mini 2 user manual and warranty card 3 TX10 driver to adjust the fastenings 4 set of stickers 5 box 5 2 Mechanical installation The device should be permanently attached It shouldn t restrict the field of view The enclosure is equipped with four fastenings The TX10 driver included should be used if the fastenings need to be adjusted or repositioned Be careful not to unscrew
Download Pdf Manuals
Related Search