Home

User`s manual for MARS-90

1. 5 1 Cleaning the Laser Machine 1 Caution use of controls or adjustments or performance of procedures other than those specified here in may result in hazardous laser radiation exposure 2 Before starting cleaning and maintenance work always switch off the device and unplug the mains plug 3 Always keep the system clean as flammable parts in the working area or exhaust area rise the fire hazard Tips You should check at least once a day whether dust has accumulated in the engraving system In case of soiling the machine must be cleaned The cleaning interval strongly depends on the material that is being processed and the operating time of the device Please bear in mind that only a clean machine guarantees optimal performance and reduces the service costs General Cleaning Notes 1 Make sure that the device is switched off and unplugged Open the protective cover 2 Move the working table into a position in which it is easiest for you to clean the surface with a window cleaning agent and paper towels 3 Thoroughly remove all loose dirt particles and deposits in the interior of the machine 4 Clean the cover of the laser tube 5 You can clean the viewing window with a cotton cloth Do not use paper towels as they could scratch the acrylic www thunder laser com DONGGUAN THUNDER LASER EQUIPMENT CO LTD tech thunder laser com 62 Tel 86 769 82665376 a THUNDER LASER MARS 90 5 2 Cleaning the Optical Parts
2. 86 769 82665376 a THUNDER LASER MARS 90 4 6 2 The main interface When the system is powered on the screen will show as below Running parameters Graph display area Speed 300mm s 30 ar a 0 153 5 400 25 0 0 ee Graph layer parameters MaxPow Running progress bar oe 499X 180 5 mm Y 235 6 mm connect Status Number e Graph Display Area To display the whole file s track and display the running track e Running parameters To display the running file s file number speed max power etc e Coordinate To display the current coordinate of X Y and Z axes e Graph layer parameters To display the layers information of the current file such as max or min power speed etc When system is idle dblclick the layer then users can change the layer s parameters and the changing would be saved e Running Status To display the current status of the machine such as Idle Run Pause Finish etc Running Progress Bar To display the progress bar of the current running file Working Number To accumulate the work number of the current file File Dimension To display the dimension of the current file Net status To display the connecting status of the Ethernet When work is Idle or finished all keys can be pushed users can select a file to run set some parameters preview to a select file etc But when work is running or paused some keys don t respond when the
3. Input Power 601 Unit 1 Building 2 BinYuan Garden N inal P JinTang Street HongLing South ominal Fower Road LuoHu District ShenZhen China Lasertype Model Type Serial Number www thunderlaser com Manufactured MADE IN CHINA www thunderlaser com tech thunderlaser com Tel 86 769 82665376 DONGGUAN THUNDER LASER EQUIPMENT CO LTD yl THUNDER LASER MARS 90 Chapter 2 Safety 2 1 General Safety Information All personnel involved in installation set up operation maintenance and repair of the machine must have read and understood the Operation Manual and in particular the Safety section The user is recommended to generate company internal instructions considering the professional qualifications of the personnel employed in each case and the receipt of the instruction Operation Manual or the participation at introduction training should be acknowledged in writing in each case Safety conscious of Working The machine must only be operated by trained and authorized personnel The scopes of competence for the different activities in the scope of operating the machine must be clearly defined and observed so that under the aspect of safety no unclear questions of competence occur This applies in particular to activities on the electric equipment which must only be performed by special experts For all activities concerning installation set up start up operation modifications of conditions and methods of o
4. Q THUNDER LASER MARS 90 5 5 Change Cooling Water for The Water Chiller BJU TIELSNON It is suggested to change the water at least once every month Make sure the laser tube is filled with water before starting the machine It is advised to add water every 3 days The quality and temperature of the cooling water affects the life time of the laser tube You need to use pure distilled water and control the temperature below 35 C 95 F DONGGUAN THUNDER LASER EQUIPMENT CO LTD N S www thunder laser com A tech thunderlaser com 70 Tel 86 769 82665376 yl THUNDER LASER MARS 90 5 6 Maintenance Plan The lens and the mirror 3 must be checking daily and cleaning if required The mirror 1 and the mirror 2 must be checking every monthly and cleaning if required The beam combiner must be checking every weekly and cleaning if required The working table must be cleaning daily The whole laser machine must be cleaning every monthly The exhaust system must be checking every weekly and cleaning if required The air blower must be checking every monthly and cleaning if required The other component as the water cooling system must be checking every monthly and cleaning if required St p p ae eS S www thunder laser com DONGGUAN THUNDER LASER EQUIPMENT CO LTD tech thunder laser com T1 Tel 86 769 82665376 THUNDER LASER MARS 90 5 7 Troubleshooting Below are some solutions to this problem
5. 86 769 82665376 a THUNDER LASER MARS 90 4 7 The First Time Running the Laser 1 Using the machine for the first time and please note that the machine working voltage of 220V 110V for USA 2 Please put the honeycomb on the standard table Unless you need to engrave on thick material or use the rotary axis 3 Lower the laser head and the upper part of the head tube must be longer than 38mm 4 Please reset Z axis after turn on the laser machine watch the guiding video to learn how to reset the Z axis and refer to the thunder laser operation video 5 Please don t use the autofocus function if there s no materials on the table For example first engraving tests The following steps describe how to successfully engrave a first pattern Please follow the individual steps 1 First switch on the computer and the Laser Tips When turn on the power of machine and note that turn on the main switch first and then the laser supply power 2 Put the object to be engraved into the laser and move into the desired position on the engraving table Usually the object is positioned in the upper left hand corner Use the rulers to determine the dimensions of the object to be engraved 3 With the positioning keys the lens is positioned over the material to be engraved You focus with the help of the focus tool or by auto focus 4 Generate a graphic with the help of your graphics software or lead in a picture that you want to eng
6. The lens has a durable multi coating and won t be damaged by correct and careful cleaning You should inspect the focus lens and the mirrors and the beam combiner according the maintenance plan If you discover a veil of haze or dirt you must clean them It is suggested to clean the mirrors lens before work every day in order to run the machine at max efficiency Follow the instructions below for the cleaning of optical parts 5 2 1 Cleaning the Focus Lens 1 Move the engraving table to a distance approx 10 cm under the lens holder 2 Move the working head into the center of the working surface and put a cloth under the lens holder so that the lens is not damaged if it accidentally falls out of its holder 3 Now you can unscrew the lens holder 4 Once positioned over a clean lens cleaning tissue remove the lens from the lens holder by carefully turning the lens holder and letting the lens and the O ring drop onto the cleaning cloth 5 Examine the O ring and if necessary clean it with a cotton bud and a lens cleaning tissue cloth 6 Remove the coarse dust as good as possible by blowing air onto the lens surface 7 Check the surface and if necessary clean the lens with the lens cleaning liquid and lens tissue 8 Hold the lens assembly by its edge with a lens cleaning tissue and use a drop of lens cleaning liquid from the little bottle which you received as an accessory delivered with the laser While holding the lens on an
7. AVOID EYE OR SKIN EXPOSURE TO DIRECT OR SCATTERED RADIATION CLASS IV LASER Opening by qualified VISIBLE LASER RADIATION WHEN OPEN personnell only DO NOT STARE INTO BEAM CLASS IV LASER CLASS IV LASER www thunder laser com DONGGUAN THUNDER LASER EQUIPMENT CO LTD tech thunderlaser com Tel 86 769 82665376 a THUNDER LASER MARS 90 Chapter 3 Process of Installing 3 1 Unpacking You receive your THUNDER LASER MARS 90 packed in a wooden box which contains the laser machine and additional accessories The following steps give you an overview of the unpacking and assembly of the laser Please follow these steps carefully Tips Keep the packing box You will require it in case of a return Dispose all waste according to the applicable waste disposal law 1 Put the wooden box on a flat and spacious room for unpacking 2 Remove the machine box carefully remove the foam material which protects the viewing window of the cover and around the machine 3 Take out the key open the door of the laser Remove the accessories box which contains all accessory parts required for the installation of the laser machine And check if there s anything damaged or missed during shipping 4 You will see an attachment table on the machine please check whether the accessories are all on the table 5 Please keep the keys and the warranty certificate well and please show us your warranty certificate if you need tech support
8. Z axis reset U axis reset Press up and down arrow keys to move the cursor to one of the entry then push Enter www thunder laser com DONGGUAN THUNDER LASER EQUIPMENT CO LTD tech thunder laser com 4 Tel 86 769 82665376 a THUNDER LASER MARS 90 key to restart the selected axis the screen will show some information when resetting 4 6 10 Manual Set When the green block is on this item push the Enter key to show as below manual mm Press Z U move item Modified press Enter Push Z U key to move the green block and when the green block is on the Mode item push X keys to select the anticipant value Continue or Manual When Continue item is selected then the Manual item is not valid on that time push the direction keys to move the corresponding axes and when the pushed key is loosed then the corresponding axes will finish moving When the Mode item is manual then pushing the direction key one time the corresponding axes will move a fixed length unless the scope is overstepped 4 6 11 Laser Set When the green block is on this item push the Enter key to show as below Laser Set ms Press Z U move item Modified press Enter Push Z U key to move the green block and when the green block is on the Mode item push X keys to select the anticipant value Continue or Manual When Continue item is sele
9. ya Se ll ul uk a 7a 4 4 4 4 4 4 le 6 oc 6 6 6 6 4 4 4 4 aaa 6 4 4 4 4 a 4 4 4 ae 1202 LAA AAA TRA separate the auto focus port Dtake out the mount mouth loosen the screw take out the air hose 2 42 4 4 4 4 ERE O BO 2 nF aD x 3 Install the 4 laser head like below a 2 4 4 4 4 4 6 6 6 a a a ER 6 4 Ss EL maaan am e De ee tarta AE l Ml Ml ee Sr e e e a Oe e do e e o a a 5 e e 64 4 4 4 4 a e e e A A AA FU A E E A A A A A A A A A A A a 4 A A A A A al a a A A A v4 LE a 4 laser head reinstall the auto focus install the mount mouth to the 4 head fix the laser head 3 connect the air hose Tips If there s no Auto focus for your machine then no need to deal with it www thunder laser com tech thunderlaser com Tel 86 769 82665376 DONGGUAN THUNDER LASER EQUIPMENT CO LTD THUNDER LASER MARS 90 2 How to replace the HR laser head 1 Move the table down till there s enough space to take the standard head out and install the HR head 2 Separate the standard head mount like above instructions 3 Install HR head like below E EE EGTATA 11111 2 1 Y Ed y T e P fix the head connect the air hose Tips Since HR head is sensitive for focus distance it s suggested to adjust the focus by manual rather than auto focus www thunder laser c
10. Certificate Product Name LASER CUTTER LASER ENGRAVER Specification MARS 90 Serial Number 6146714437 Inspection Date July 22 2014 Ex Factory Date July 27 2014 Quality Inspection Conclusion PASS THUNDERLASER Product Warranty Terms 1 Warranty Period The warranty for whole machine is effective 14months from the Ex Factory Date But for the laser tube focus lens the reflective mirrors air compressor water pump air pump and exhaust fan the water chiller the warranty is 6months from the Ex Factory Date 2 Warranty Provisions 1 Please keep the certificate you need to show us this certificate for warranty 2 Damage caused by lightning or other electrical system is not covered 3 Damage caused by improper operations like liquid leakage to mainboard or power supply is not covered Damage caused by accidents disasters wars and other irresistible factors is not covered 5 Damage caused by not following our User Guide Manual and result in improper operating and maintaining is not covered 3 Warranty 1 We will send you the spare parts and offer tech support for free during warranty when there is a machine fault including the part fault 2 User will need to send back the old parts to us within one week after receiving the new parts we will inform you the address for returning the old parts and a tracking number must be provided as voucher 3 If we don t get the old part or tra
11. LTD tech thunder laser com Tel 86 769 82665376 Q THUNDER LASER MARS 90 The connection of the machine and the Water pump Take out one of the water pipes and connect to the water pump the other side connect to the machine where marked as Water IN 2 The other pipe please connect to the machine where marked as Water OUT the other side directly into the water Like below We will provide a certain pump power cable for different countries and the power cable has been connected to the pump already before we send it out Get through the water chiller or the water pump and turn on the main power Check the water chiller or pump to work If normally work the green light will light or water will flow from the pipe www thunder laser com DONGGUAN THUNDER LASER EQUIPMENT CO LTD tech thunderlaser com Tel 86 769 82665376 YO THUNDER LASER MARS 90 Chapter 4 Operation 4 1 Machine View www thunder laser com tech thunderlaser com Tel 86 769 82665376 a THUNDER LASER MARS 90 1 Top lid 16 LED lamp 2 Blow air conditioner 17 Right up side door 3 Auto focus sensor 18 Right side door 4 Left up side door 19 PC connection port USB 5 Left side door 20 U disk connection port USB 6 Laser head 21 Main power switch 7 X axis 22 Laser power switch 8 Front door 23 Power supply socket 9 Working table 24 Laser tube cover 10 Y axis 25 Exhaust hos
12. back to the original point and the warning light will return to the green light then you can repeat engraving www thunderlaser com DONGGUAN THUNDER LASER EQUIPMENT CO LTD tech thunder laser com 57 Tel 86 769 82665376 a THUNDER LASER MARS 90 4 8 Rotary axis Attachment The rotary axis attachment option in the printer driver is used in combination of the rotary axis attachment to engrave cylindrical objects To compensate for the different diameters of different objects the image must be adjusted This is performed automatically by the engraving driver by selecting the rotary axis option and entering the diameter of the object to be engraved The Rotary size L length 65CM MaxDiameter 10CM To install and set up the rotary axis attachment proceed as described as follows 1 Move the working table to the lower position switch off the laser and open the top lid 2 Put the rotary axis attachment onto the working table and connect the rotary axis attachment to the working table Before you fix the rotary axis attachment align it so that its sides are parallel to the rulers The rulers offer a visual aid for placing the graphic 3 Connect the rotary axis attachment via the control cable with the connector of the motion system The connector is located inside the right front of the laser Connected it to this interface and fixed then turn on the switch and reset the rotary device by press the reset button on
13. connect the air compressor or the water chiller to the above interface if connect them to the above interfaces that cause in failure of the machine the warranty does not covered 3 8 4 Connecting the Air System First of all Install a air blowing mouth copper to the air system then connect the hoses white side to the mouth the other side to the machine After that please connect the power cable of the air system to the machine Like below The input voltage must correspond AC 220 V 50 Hz or AC 110 V 60 Hz see information label beside the connection socket www thunderlaser com DONGGUAN THUNDER LASER EQUIPMENT CO LTD tech thunderlaser com Tel 86 769 82665376 a THUNDER LASER MARS 90 3 8 5 Connecting the Cooling System lf you have the water chiller and please connect to the water chiller priority If not and please connect to the water pump The connection of the machine and the Water chiller Take out one of the water pipes and connect to the water chiller where marked as OUTLET the other side of the pipe connect to the machine where marked as Water IN 2 The other pipe please connect to INLET of water chiller and Water OUT of machine Like below We will provide a certain chiller power cable for different countries and the power cable will be put inside a box together with the water chiller www thunder laser com DONGGUAN THUNDER LASER EQUIPMENT CO
14. filled with paint and cast acrylic for normal engravings Cast acrylic can be best engraved without protection foil It is better to engrave the entire surface with a low energy setting 3 Engrave the rubber stamp The various mixtures and densities of rubber plates cause a slightly varying engraving depth The settings in the overview table give a good indication Since engraving a standard rubber material requires a relatively high laser power the laser power is principally set to 40 or more high and only the speed is varied Due to their lower density so called micro porous rubber materials allow a significantly higher engraving speed Test the rubber first to find out the correct speed setting The RDWorksV8 software using the engraving function you can choose Ramp Effect or common engraving once you choose Ramp Effect and you will need to set a minimum power lower than Max Power generally we set it to about 15 and input a value with the Ramp Length what you want but if you want to make it better you may need to test different kinds of power and speed by yourself then you can get the best result Engraving rubber produces a considerable amount of dust and terrible gas Therefore a well dimensioned exhaust system and its regular maintenance are very important www thunder laser com DONGGUAN THUNDER LASER EQUIPMENT CO LTD tech thunder laser com 61 Tel 86 769 82665376 oO THUNDER LASER MARS 90 Chapter 5 Maintenance
15. for the machine failure then we will provide you the best technical service 6 Remove the sponge and nylon cable ties from inside the machine and then start to install the machine below chapters are installation details www thunder laser com DONGGUAN THUNDER LASER EQUIPMENT CO LTD tech thunder laser com 16 Tel 86 769 82665376 a THUNDER LASER MARS 90 3 2 Contents of Delivery 1 Transport and service packaging 2 Laser including optics 3 Other optional components that you buy 4 Accessories box and the other machine parts which contains the following parts ITEM QTY 1 Fuse 2 2 Ruler 1 3 Long USB Cable 1 4 228 Belt 1 5 Power Cable 1 6 Straight Screwdriver 1 7 Cross Scrwdriver bit 1 8 Ruler for Adjust Focus 1 9 6mm Acrylic Focus Tool 1 10 Water Pump 1 11 Micro Switch 1 12 Lens Cleaning Liquid 1 13 Air Comperssor 1 14 Lubricating oil 1 15 M3M4M5 Allen Wrench 1 16 Main Switch 1 17 Sticker 5 18 Ribbon 10 19 Exhaust Fan 1 20 Exhaust Pipe 2 21 Hose Clamp 3 22 Lens Mirror Cleaning Paper 1 23 Lens Mirror Cleaning Cloth 2 24 Socket 1 25 Silcon Water Pipe 2 26 Key 3 sets 27 Crimp Tool 1 28 Mirror holder retation tool 2 29 Multimeter 1 www thunderlaser com DONGGUAN THUNDER LASER EQUIPMENT CO LTD tech thunder laser com 17 Tel 86 769 82665376 THUNDER LASER MARS 90 5 THUNDER LASER Product Warranty Certificate Pa O DONGGUAN THUNDER LASER EQUIPMENT CO LTD Product Warranty
16. is on a target file name presses the Enter key the selected file will be previewed on the main interface and then if Esc key is pushed the preview will disappear X keys could be used to move the cursor left and right All the item show as below e Read mem file read the memory file list Udisk read the U disk file list Other the other operation of the memory files Run To run the selected file Track To track the selected file and the track mode is optional Work time To forecast the running time of the selected file and the time is accurate to 1ms Clear count To clear the running times of the selected file Delete To delete the selected file in the memory e Copy to Udisk To copy the selected file to Udisk lf the Other entry is pressed the system will show as below www thunderlaser com DONGGUAN THUNDER LASER EQUIPMENT CO LTD tech thunder laser com 53 Tel 86 769 82665376 oO THUNDER LASER MARS 90 Current work time Clear all count delete all file Format speedly Format drastically Total 10 e Current work time To forecast the running time of the current file the current file No is showed on the main interface and the time is accurate to 1ms e Clear all count To clear the running times of every file in the memory e Delete all file To delete all memory files e Format speedily To format memory speedily and then all the files in memory will be deleted e Format d
17. relay has a freely adjustable delay time from 1 300 seconds Set up delay time Enter Menu switch once The red LED will blink and the display will show you the delay time in second for the first relay A yellow LED close to the active relay will show you Which one is active The display does show the delay time in seconds By pressing down or up you can change the value By holding a switch down for more than 2 seconds the value will increase or decrease automatically By pressing Menu you can switch to relay number 2 now and set the delay time for this one For changing delay values for 3 and 4 relay you have to press Menu again When 4 relay is active and you press Menu again The TL Timer will turn back to normal operating mode the red LED will stop blinking After turning of power the TL Timer will remember the delay time values you did enter before Relay Output Each of the 4 relays offers a opening and closing switch with current capacity of max 8Amps and a power capacity of max 1000W Higher loads must be controlled by using a power contactor www thunder laser com DONGGUAN THUNDER LASER EQUIPMENT CO LTD tech thunder laser com 35 Tel 86 769 82665376 THUNDER LASER MARS 90 About TL Timer controller interface and buttons description DOWN FN CONTRI L 4 CHAN EL 1 Interface 1 connection warning light delay time is set to 1 second Factory default settings the user can
18. to use a High pressure air compressor set while working High pressure air compressor set including two parts high pressure air compressor and water separator Tel 86 769 82665376 YO THUNDER LASER MARS 90 High pressure air compressor a a j High pressure air compressor is used for blowing air to reduce material burning Note After two hours of continuous work of air compressors and it will needs to stop working for half an hour or more Water separator When we use the High pressure air compressor for blowing air it will absorb much moisture with air at the same time If we just let the moisture go they will gather on the focus lens and when the laser working the water moisture will heat that may lead the lens break Thus we need a water separator for help it can stop moisture reaching lens Water separator was installed between the air compressor and laser head For how to connect and use the High pressure air compressor set please refer to below lesson http www thunderlaser com technical support downloads category others html If you have any question please contact with us tech thunderlaser com THE END www thunder laser com DONGGUAN THUNDER LASER EQUIPMENT CO LTD tech thunderlaser com 78 Tel 86 769 82665376
19. videos php or http www youtube com watch v likSTBR2_hM amp feature player_embedded www thunder laser com DONGGUAN THUNDER LASER EQUIPMENT CO LTD tech thunder laser com 2 Tel 86 769 82665376 yl THUNDER LASER MARS 90 Contents Chapter Generalista 5 dl oie Me tall ias AAA A nr a 5 1 2 DESISNalcd arrendar soii 6 o DIS POSAU COALS AAA e II A 6 1 4 Technical Dat Device SpecilCa lO easirina ni accua 7 DVI ir sabe l tonic actora ivo acaparan iia 9 Chabter Z SAN r 10 2 l Gencralsateiy Inora aora a eh ack 10 22 Easra O errr err r E ocda 12 2 3 Safety Precautions When Operating the Device oooooonnnnnnccncnoncnnconnnonnnnnnnnnnnnnnnnnnnnnnnnnnnnononnnnos 13 24 Warnes and Intormation Labels sionistas dirt 14 Chapter gt PROCESS OE UMS ssrin rna NN Aaaa aaa 16 OW MUM A E E 16 SAND y OP oan caaenaussisedeasansacbonwnoasoesaseasncsenesunnseesaavestia 17 SA Ses sees ces a cad boned eee osenneueteeee eoddouseetere 19 SA GlObe PMS tA OM coria nario osado ate ali da 20 AAA Un auanasaeseanooesavansests 22 LOAI Syste Wins AMA e UE OR RE 22 327 Computer Reg Uirements nano ici 23 AO A aa ias 24 ed A A e O 24 SA Bo ti Che he ONE PPP APNPRCRONPO OUOO NEE Nane ENON 25 3 0 3 Comnectins the Exhaust Syste vedada adds 26 3 6 4 COMME CU S the Ait Syste edad c Lala o 27 3 8 5 Connecting the Cooling System oooooooooooonccncnnnnnoncnnnononononnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnos 28 Chapterd OperaNoii cssecctccste
20. working 9 Working table The honey comb plate to be processed is put onto the working table Put the material on the working table for engraving amp cutting 10 Y axis The motion system is that performs the mechanical movements in Y direction The Y axis is visible in the working area 11 Connection socket for rotary attachment option Supplies the rotary attachment with the required electric signals 12 Flap protection sensor This is where Open flat protection exist Laser will stop working once the cover has been opened 13 The display You can control the X axis Y axis and Z axis manually by the display panel it also shows the working time power speed and the whole working time and affords many function options please view this chapter 4 3 for detail 14 The rotate emergency switches Once there s an accident happen laser catch fire laser out leakage during working please turn off this switch immediately 15 The warning light The light will turning red while laser working and it ll turning green when laser stop working 16 LED lamp It s used for lighting the working table once turn the Main switch on 17 Right up side door 18 Right side door There are laser controller driver Hybrid Servo Drive and Micro Stepper Drive power supplier both 24v DC and 36vDC filter the main connecting cables and cooling fan here please open this door for checking these parts but must pay attention to the electric c
21. 1000 x 730 mm 9 1 inch 230 mm 9 1 inch 230 mm Max Height of work piece No Motorize Table Standard Laser head 1 2 1 inch 27 55mm Max Engraving speed Cutting speed Motor Drive Work piece table Max load of work piece table Net Weight Lenses available focal distance Focus lens diameter Reflector diameter Beam combiner diameter Dimensions WxDxH Max Part Size W x Lx H Front Door Closed Pass Through Door Features Standard 39 inch sec 1000 mm sec Standard depending on material thickness laser power Easy Servo Motor Hybrid Servo Drive Solid metal Honey comb table 40 kg 230kgs 507lbs 2 0 20mm 2omm 25mm 97 1 x 42 7 x 48 5 1450 x 1085 mm x 1105 mm 39 4 x 28 7 x 10 6 1000 x 730 mm x 270 mm 39 4 xco x 1 2 1000 xeomm x 30 mm Red Dot Pointer Auto Focus Motorized Table Pass Through Door Air Assist Water Pump Exhaust Fan Honey Comb Table 2 0 50 8mm Focus Lens Easily Adjustable Home Position LCD Display 3D Engraving No Water protection Emergency Stop Open cover protection TL Timer Ammeter The warning light Optional Rotary Attachment Water Chiller Attachment High Resolution head up to 1000DPI while standard laser head Max is 500DPI Air Compressor Water Filter Control System Laser power Interface Hardware Interface Software Operating Modes Buffer Memory Laser Equipment www thunderlaser com tech thunderlaser com Tel 86
22. 769 82665376 Adjustable from 2 95 typically 12 95 USB connect to PC and U disk Ethernet connect to PC RDWorksV8 Optimized raster vector and combined mode 128 MB Standards DONGGUAN THUNDER LASER EQUIPMENT CO LTD a THUNDER LASER Laser Type Wavelength Cooling System Air Cooling System Water Cooling System Electricity Power Fuse Electricity Requirement Power consumption Recommended fuse Ambient Conditions Ambient temperature Humidity Laser Safety Laser class www thunder laser com tech thunder laser com Tel 86 769 82665376 MARS 90 Sealed CO2 Glass Laser Tube Laser Power 80W 100W 130W 10 6um Air Cooled Water Cooled 110 to 240 volts 50 or 60 Hz Single phase 1600W Assembly 80Waitt Laser Tube 15A 220V 15A 110V 15 C to 25 C 59 F to 77 F 40 to max 70 not condensing CDRH Laser Safety Laser Class 4 H CE compliant FDA approved DONGGUAN THUNDER LASER EQUIPMENT CO LTD a THUNDER LASER 1 5 Manufacturer s Label MARS 90 The manufacturer s label is located on the back of the device see Figure below It is recommended to enter data such as serial number and year of manufacture into the manufacturer s label below so that you always have this data handy if you have problems with your device or require spare parts AO vHunver LASER CUTTER THUNDER LASER TECH CO LTD This Product Complies With 21 Cfr Part 1040 10
23. 86 769 82665376 YO THUNDER LASER MARS 90 3 Open the rotate emergency switch must do it for the first time to use the machine Like below KS 4 After carried the machine into room please re fix the foot of the four corners Please refer to below shown Y N www thunder laser com a DONGGUAN THUNDER LASER EQUIPMENT CO LTD techOthunderlaser com Tel 86 769 82665376 Q THUNDER LASER MARS 90 3 5 Exhaust System Requirements To guarantee the right ventilation during the engraving and the cutting The device must be equipped with a fine exhaust fan generation of rubber dust if you use an carbon filter neutralization of smells will be better for exhaust effect A good exhaust fan of the outgoing air is also required when cutting plastics or engraving wood Connection see section 3 7 3 connecting the Exhaust System Do not start the machine without an adequate exhaust system 3 6 Air System Requirements To guarantee do not catch file and too much smoke during the engraving and the cutting The device must be connecting with the laser to make sure the laser is safe during the work www thunder laser com DONGGUAN THUNDER LASER EQUIPMENT CO LTD tech thunderlaser com Tel 86 769 82665376 a THUNDER LASER MARS 90 3 Computer Requirements The following recommendation represents the minimum requirements When using a more powerful computer the
24. IAT AL ALITY LEA LEA OME eN Read more high resolution samples just click below link http www thunderlaser com samples category 19 high resolution html Engrave high definition picture THUNDERLASER HR Head was really superior for engraving pictures the high density laser spots allows you to achieve a higher resolution higher megapixel counts photo engraving than standard laser head Comparison between HR_head_and_standard_head download http www thunderlaser com download Comparison 20between HR head and standar d head paf www thunderlaser com DONGGUAN THUNDER LASER EQUIPMENT CO LTD tech thunderlaser com Tel 86 769 82665376 THUNDER LASER MARS 90 4 laser head 4 laser head owns a longer focal distance than 2 standard head thus for cutting thick material it makes the cutting edge more smooth and straight Laser focus comparison between standard 2 head and 4 head Standard laser head focus 4 laser head focus www thunderlaser com TT DONGGUAN THUNDER LASER EQUIPMENT CO LTD tech thunderlaser com 16 Tel 86 769 82665376 7 C 17mm thickness foam samples by using 4 laser head and standard 2 head Samples for 4 laser head Acrylic Note when we cut thick material usually more than 10mm with 4 laser head and the material are very easy to catch fire for example wood foam plastic etc usually we would suggest customer
25. QUIPMENT CO LTD O www thunderlaser com tech thunderlaser com 86 769 82665376 Tel THUNDER LASER MARS 90 5 2 2 Cleaning the Mirrors There are three mirrors in the operating area of the laser which may have to be cleaned if they are soiled To clean the reflector follow the instructions below N A _ The Mirror 1 The mirrors are easily get dirty And this will reduce the efficiency of the laser beam Meanwhile laser energy absorbed by the mirror may cause heat and destroy the mirrors too For the first mirror you can clean them directly The Mirror 2 second mirror Make sure the power of the laser machine is turned off while cleaning The 2 mirror is installed on the left side of X rail For the second mirror you can clean them directly The Mirror 3 WUC eee ee etree rene Red IAS HH z a LITIO ff Cautions 1 Mirrors must be cleaned carefully by using lens cleaning paper lens cleaning cloth to avoid scratching the surface 2 Do not touch the surface of the mirrors lens after cleaning 3 The concave side of the lens must be on the bottom when installed www thunder laser com G A DONGGUAN THUNDER LASER EQUIPMENT CO LTD tech thunderlaser com 65 Tel 86 769 82665376 i NR THUNDER LASER MARS 90 How to take out the mirror 1 2 and 3 and please just as following the picture indicated e 1 The mirror 1 2 The
26. TO E e E E 51 A O 52 420 20 Ple C aiii ba titres 53 4 6 21 Alarm Information of Display siissiseescaccsedadscdecnuddasvessucsdecs ld e ai aia 55 4 1 The First Hime Running the Laser cssaxscsssascnaseesmacssensewassssncseceasovaaanasovaasaadanaensaueesnopengesaensiaedasaans 56 4S ROtary Engraving Attachment 1 crsssassccesencacntaceaencssapnensosasneacenossenausadeensunasasinsoaadbenconesoeasasasnaasananes 58 AO For Laser BRASTAYIDO curra sinaloa 61 Ao Ec A In o e 62 Jl leamos the Laser MaDe seo onerosa 62 O a O oo Me A aE cus osacaese E ERE 63 5 2 1 Cleaning the Focus Len sitial lll is 63 22 O ii o AA o 65 52 5 leanne Bean E omDi NET semerre ae ea E E aE O DeCaro 67 Dy ai ali S A AMA E AE EET 68 4 Check he Beam Pa asado re oi 69 5 5 Change Cooling Water for The Water Chiller oooooonnnnncccnnncccnononoonnnoooncccnnncnonnnnnnnonnnnnnnnnos 70 0 ate MC P e E E E E 71 TT T2 Chapter 6 The Characteristics of Thunder Laser sseccsssssssssccecccoccosssssseccecccccccccossssssssesccceeeesosso 73 Gal Laser Heads Tor Ap PN CAMO rita cia ica coa 73 www thunder laser com DONGGUAN THUNDER LASER EQUIPMENT CO LTD tech thunderlaser com 4 Tel 86 769 82665376 a THUNDER LASER MARS 90 Chapteri General 1 1 General Information Caution Please read and follow this Operation Manual carefully before installation and operation Damage to persons and or material can result from not following indi
27. angle flush both surfaces of the lens to wash away coarse soiling 9 Putthe lens on aclean lens cleaning tissue Put some lens cleaning liquid on one side of the lens Leave the liquid to take effect for approximately one minute and then gently wipe it away with lens cleaning tissues soaked with lens cleaning liquid 10 Finally dry this side of the lens with dry lens cleaning tissues and repeat the cleaning process on the other side of the lens Never use a cleaning tissue twice Dust accumulated in the cleaning tissue could scratch the lens surface 11 Examine the lens If it is still soiled repeat the cleaning process until the lens is clean 12 Carefully insert the lens into the lens holder Ensure that the rounded side convex of the lens is facing upwards Then put the O ring on top of the lens 13 Carefully assemble the lens in reverse order www thunder laser com DONGGUAN THUNDER LASER EQUIPMENT CO LTD tech thunder laser com 63 Tel 86 769 82665376 MARS 90 Y THUNDER LASER How to take out the focus lens please just as following the picture indicated MAMADA titt ttr TTT A d a E E da A AAA AAA RA LAA A AAA o a On Oe ee oe wp ed ay a ap eg at cl an S as a i m staan A a oe a J Fey a a a nr AD E a ae rh ae hoe a r in Oe d ane Mu mamm a a nini pisanarnann n aaaan TTT TT TT TT TT TT o5s4555558285500222558228R RR RR ee el a i d ABARCA AA LAA A a DONGGUAN THUNDER LASER E
28. be set if required 2 Interface 2 connection air pump delay time is set to 5 second Factory default settings the user can be set if required 3 Interface 3 connection exhaust fan delay time is set to 5 second Factory default settings the user can be set if required 4 Interface 4 reserved interface users can connect the relevant equipment if required 5 LED lights display set the delay time for viewing each interface and enter 6 Enter button 7 Reduce the delay time button 8 Increase the delay time button 9 24V power connection 10 Working signal connection Where the TL Timer is installed with Thunder Laser machine please refer to the pictures as bellows M DONGGUAN THUNDER LASER EQUIPMENT CO LTD www thunderlaser com A tech thunderlaser com 36 1 86 769 82665376 UN THUNDER LASER MARS 90 4 4 How to replace the 4 inch and HR laser head 1 How to replace the 4 inch laser head 1 Move the table down till there s enough space to take the standard head out and install the 4 laser head 2 Separate the standard head mount like below y e y _ Ml D Le ote Z ppssessssssesesess III tt to IIA AI AI IO EPA 7 MAPA ll AO 46444 4 ll E E ll 6S ae ll Y MENN amp N n G a GAIA ASS OO S 06 64444 8 4 Ge E gt A A A A ee ee IEEE ee CO y t MAA ANNA AA all a S a a a a S Vea ar a ao ooo M DD DD O O ld ll 4 4 4
29. ccscccteccteccdecsesacscaveceatecanceszacebscetessabecsateeasenssacussnelsasatsaniasseeeeareataeaqesiesanees 30 NI TNIV NIO E E E EEEN 30 42 ONOPE SWI soon esco iconos NEE E EE 34 4 3 How to use the TL Timer ninia 35 4 4 How to replace the 4 inch laser head and HR laser head ou eee eee eccccccccecccceceeeeeeeseeessseeeeeeeees 37 4 5 How to manual adjust focus distance urinaria diia 39 4 6 How to Use the Display cestas aiii 42 4 6 1 Function of the BuUttODS oooooononnnccnnnnnnnnnnnnnnnononononononnnnnncnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnos 42 4 6 2 The Main UAT AC cea ccs saat acai etd aa cise stata A E N 44 BO Oe A A A 45 4 6 4 Max Min Power KeyS ccssssssseeeccccceeeeaeeaaaesssesssseseeeeeeeeeeeeesaeeeeessseeeeeeeeeeeeeeeeaeaaageaeeesees 45 4 6 5 Set the Layer Parameters lt sessivcsiestesedersidesdiwasadewesidenisenidank sedasiadieiesentitebioniieiwaaed saadsaedsnsiieedoons 46 AU E OI EA EEES 46 AO ZINN ri ida laa ie 46 A MO p E E E T E E E E ies 46 AS A 46 A E PO EE A 48 BOTA MASS AS IE A PENEI A E T T 48 www thunder laser com DONGGUAN THUNDER LASER EQUIPMENT CO LTD tech thunderlaser com 3 Tel 86 769 82665376 yl THUNDER LASER MARS 90 AO 12 OACI SE sica iii sion lidia lili tall 49 A e A ACE EIS Ve ES AE E A A E A E E E E A 50 A 0 WAT Fact Parane Secene pE Ea 50 KTT AOE O aE EE EEOSE ESSES EIEE 50 BONG aM Ga Fe pirrer E EO E A erar aerar 50 EE 101 0 A EE 0 EN E EEEE E O E E E E 51 E
30. ce shows some system input information such as limiter status the status of the water protecting and the status of the foot switch etc When the input is validated the color frame will be green otherwise it s gray 4 6 19 Screen Origin If the Screen Origin item is pressed the system will show as below Origin locat Top left lt gt To modify press gt Modified press Enter There are four entries to be selected Top Left Top Right Bottom Left and Bottom Right When one is selected the previewed graph on the screen would be enantiomorphous based on X or Y direction This item is only used to preview the file on the screen and it is no meaning to the machine s movement Caution www thunderlaser com DONGGUAN THUNDER LASER EQUIPMENT CO LTD tech thunder laser com 52 Tel 86 769 82665376 Oe THUNDER LASER MARS 90 4 6 20 File Key 1 Memory File On the main interface if File key is pressed it will show as below Count Read mem file File 01 300mm s MaxPow 30 0 30 0 Other A E Track Work time Clear count Delete Copy to udisk Idle 00 00 00 Count 99 X 180 5 mm Y 235 6 mm connect When showing this menu the system would read the memory file firstly the file name and the work times would be listed in the area and the selected file is previewed in the bottom right area Y keys could be used to move the cursor on the file name list When the cursor
31. cking number one week after user receiving the new one we will stop the machine warranty until we receive the old part And user must take responsibility for his own loss during this period 4 We will charge for replacing repairing including labor costs and transportation costs when the warranty is expired 5 User will need to buy new parts for replacing from us or with our permission if buy from other company If not we won t take any legal responsibility when there s any tech problem or machine fault meanwhile we will stop the warranty If there s any problem in future we will provide you tech support by sending email telephoning Skype msn DONGGUAN THUNDER LASER EQUIPMENT CO LTD No 197 Hudong Road Shatian Town Dongguan City Guangdong Province China Post code 523980 Tel 86 769 82665376 Email tech thunderlaser com Website www thunderlaser com DONGGUAN THUNDER LASER EQUIPMENT CO LTD e 5 y e 18 amp GB Iq www thunder laser com DONGGUAN THUNDER LASER EQUIPMENT CO LTD tech thunder laser com 18 Tel 86 769 82665376 C a THUNDER LASER MARS 90 3 3 Location Before you install the laser system you should select an appropriate location Follow the guidelines shown below 1 Avoid locations where the system is exposed to high temperatures dust and high humidity The humidity must not exceed 70 and the temperature must not be close to the dew po
32. cted then the Laser Set item is not valid on that time push the Laser key to splash the enabled lasers and when Laser key is loosed then the lasers will finish splashing When the Mode item is manual then pushing the Laser key one time the enabled lasers will splash a fixed time www thunder laser com DONGGUAN THUNDER LASER EQUIPMENT CO LTD tech thunder laser com 48 Tel 86 769 82665376 a THUNDER LASER MARS 90 4 6 12 Origin Set When the green block is on this item push the Enter key to show as below _ Muti origin enable _ Origin enablei Origin enable3 Origin enable2 Origin enable4 Set origin lt gt Next origin o lt gt Press Z U move item Modified press Enter Push Z U key to move the green block to the anticipant item and when the green block is on enable items push Enter key to enable or disable the item when enabled the small diamonds is green and when disabled the small diamonds is grey When the green block is on the Set origin item or the Next origin item push the X keys to select the value Pay attention to if when the green block is on the Set origin item push the X keys to select a value then Enter key must be pushed to valid the change or the change is invalid Each item introduced as below gt Multiple Origins Enable Yes or No can be selected If you select No the system wi
33. d are accessible from the exterior www thunderlaser com DONGGUAN THUNDER LASER EQUIPMENT CO LTD tech thunderlaser com Tel 86 769 82665376 Q THUNDER LASER MARS 90 3 8 2 Connecting the Computer Connecting the Computer and the machine by using the USB cable Like below www thunder laser com DONGGUAN THUNDER LASER EQUIPMENT CO LTD tech thunderlaser com Tel 86 769 82665376 YO THUNDER LASER MARS 90 3 8 3 Connecting the Exhaust System Installation of the exhaust transposition Insert one side of the gray exhaust pipe into the fan inlet and the other side into the fuselage behind the exhaust tank Insert one side of the blue exhaust pipe into the fan outlet and put the other side of the pipe outside where you work If the machine is far from the outside of the room that the gas manufactured by the machine cannot be discharged then you might need an dust fume filter it can keep the air quality of your working environment well Please refer to the following pictures about how to install the exhaust pipe Also follow the operation and maintenance instructions in the Operation Manual of the exhaust system The input voltage must correspond AC 220 V 50 Hz or AC 110 V 60 Hz see information label beside the connection socket www thunder laser com DONGGUAN THUNDER LASER EQUIPMENT CO LTD tech thunderlaser com Tel 86 769 82665376 a THUNDER LASER MARS 90 Tips Do not
34. e 11 Connection socket for rotary 26 Blow air port 12 Flap protection sensor 27 Water in and water out 13 The display 28 Rear door 14 The rotate emergency switches 29 Manufacturer s label 15 The warning light 1 Top lid lf the Top lid is opened no data is processed When the protection cover is opened during working the motion system is stopped and the laser source is turned off During processing of commands the protection cover must only be opened after pressing the Pause button 2 Blow air conditioner Used for controlling the air blowing amount 3 Auto focus sensor Used for the automatic focusing of the work table 4 Left up side door Open this door for cleaning the second reflective mirror 5 Left side door There is laser power supplier Ammeter TL Timer filter etc please open this door for checking these parts but must pay attention to the electric current 6 Laser head The laser and red dot pointer comes out from the laser head and the Auto Focus switch is installed on the laser head too The bottom of laser head is parallel to the bottom of the autofocus switch 7 X axis The motion system is that performs the mechanical movements in X direction The X axis is visible in the working area www thunder laser com DONGGUAN THUNDER LASER EQUIPMENT CO LTD tech thunder laser com 31 Tel 86 769 82665376 O THUNDER LASER MARS 90 8 Front door Open this door for cleaning the waste after
35. e laser lt gt head also can be used to change the parameters in the control panel lt gt D button The Z U key can be pressed when the system is idle or the work is finished On pressing this key it will show some entries in the interface each entry includes some functions Z axes move U axes move each axes to go home etc lt gt Reset button reset the machine Laser lt gt Laser button single press to draw a dot press and hold to drill a hole lt gt Speed button Set the speed of the current running layer or set the direction keys move speed Min Power Min Power button Set the min laser power of the current running layer www thunder laser com DONGGUAN THUNDER LASER EQUIPMENT CO LTD tech thunderlaser com Tel 86 769 82665376 a THUNDER LASER MARS 90 Max Power Max Power button Set the max laser power of the current running layer or set the power of Laser Key File File button The management of the memory and U disc files Start Pause Start Pause button run pause the current job Origin Origin button set the starting point for the laser head Frame GO Esc Frame button To track by the current file s frame Esc button To stop work or return to the last menu lt gt Enter button confirm your selection www thunderlaser com DONGGUAN THUNDER LASER EQUIPMENT CO LTD tech thunderlaser com Tel
36. ent job According to customer s application we have three kinds of laser head for choice TYPE LASER DOT SIZE FOCAL FUNCTION DISTANCE Standard head 0 0039 0 099mm 5 0mm 6 5mm For common cutting and engraving HR head 0 0020 0 050mm 3 0mm 4 0mm For engraving high quality picture and cutting very thin material 4 laser head 0 0078 0 198mm 9 0mm 1imm For cutting thick material Note 1 Standard head means 2 head usually we use it for cutting material less than 10mm thickness and engraving simple patterns Note 2 HR head is special for engraving high quality picture and cutting very thin usually less than 1mm material for getting a precise job Note 3 4 laser head is special for cutting thick material usually more than 10mm Usually we install a 2 standard head for our Thunder Laser system and HR head and 4 head are optional parts You can choose them according to your job requirement HR head High Resolution head HR head for short which was made by special structure this structure allows laser beam to be focused into a much smaller focal dot and it is suitable for intricate tight tolerance engraving and for direct marking on some metals 106 19 106 ant 6 www thunder laser com DONGGUAN THUNDER LASER EQUIPMENT CO LTD tech thunderlaser com 13 Tel 86 769 82665376 THUNDER LASER MARS 90 Unique accessories from THUNDERLASER For expanding more capabilities to use Thunder Laser system y
37. four origins are enabled when the memory file function is Prompt rted or the processing file is uploaded into the PC and this file selects Take the Original Origin as current Origin the work started for each time will use different origins The rotation order of origin is 1 gt 2 gt 3 gt 4 gt 1 gt 2 4 6 13 Set Fact Parameters After the Set Fact Para is selected and the Enter key pressed the interface will show the specific password to be entered when set as default parameter Password Password error 0123456789 ABC DEFGHIJ KLMNOPQRST UVWXYZ Push X keys and Y keys to select the characters and push the Enter key to valid the characters when finishing enter the password that is to say the six characters if the password is error it prompts there is some error or all parameters are stored After the manufacturer regulates all parameters of the machine well including all manufacturer parameters and user parameters this function can be used to store the well regulated parameters to help users to recover the original parameters including all manufacturer parameters and user parameters through selecting Recover Para when they regulate parameters improperly 4 6 14 Def Fact Parameters After the Def Fact Para is selected and the Enter key pressed the Successful Recovery dialog box will pop up to prompt that all manufacturer parameters and user parameters are recove
38. graphics are generated and displayed faster and the computing times and the data transfer to the laser are reduced To use the newest software version you might have to abide other requirements Windows 8 32 bit or 64 bit Windows 7 82 bit or 64 bit Windows Vista with Service Pack 1 or later Windows XP with Service Pack 2 or later e 1024 MB of RAM 400 MB of hard disk space e Pentium 3 or 4 processor or AMD Athlon XP e 1024 x 768 or better monitor resolution e 1 free USB interface e 1 free Ethernet interface e Mouse www thunder laser com DONGGUAN THUNDER LASER EQUIPMENT CO LTD tech thunder laser com 23 Tel 86 769 82665376 yl THUNDER LASER MARS 90 3 8 Connections Perform the connections exactly in the order described otherwise electrostatic charging can damage your computer and or the electronics of the laser system 3 8 1 Connecting the Mains Connect one end of the mains cable with the connection socket at the rear side of the laser device see Figure below and the other end with a protected power ouilet Mains voltage and operating voltage must correspond AC 220 V 50 Hz or AC 110 V 60 Hz see information label beside the connection socket The machine certain Power Cable for each country was put inside the Tool box with machine Under no circumstances switch on the device if the voltages do not correspond Tips The main fuses are located inside the connection socket an
39. ing applications with 80 W the use of the cutting table is absolutely necessary 3 Use of the system in other areas is against the designated use The manufacturer does not admit liability for damage to personal and or equipment resulting from such use 4 The system must only be operated maintained and repaired by personnel that are familiar with the designated field of use and the dangers of the machine 5 Non observance of the instructions for operation maintenance and repair described in this Operation Manual excludes any liability of the manufacturer if a defect occurs 6 Caution when processing conductive materials carbon fibers Conductive dust or particles in the ambient air might damage electrical components and lead to short circuits Bear in mind that those defects are not warranted 1 3 Disposal remarks Do not dispose the machine with domestic waste Electronic devices have to be disposed according to the regional directives on electronic and electric waste disposal In case of further questions please ask your supplier He might take care of proper disposal www thunder laser com DONGGUAN THUNDER LASER EQUIPMENT CO LTD tech thunder laser com 6 Tel 86 769 82665376 a THUNDER LASER MARS 90 1 4 Technical Data Device Specification Mechanics Working area Table Size Z Axis Height Max Height of work piece Motorized Table Standard laser head 35 4 x 23 6 900 x 600 mm 39 4 x 28 7
40. int 2 Avoid locations where the system is exposed to mechanical shocks 1 Fuse protection Do not connect other devices via the laser fuse as the laser system requires the full amperage Tips 1 Avoid locations with poor air circulation 2 Select a location whose room temperature is between 15 C and 25 C 59 77 F Avoid higher ambient temperatures and strong exposure of the engraver to the sun Use blinds if required 3 Select a location close to ventilation if available 4 Select a location that is not more than 4 50 m away from your computer max cable length to avoid disturbing interferences 5 Try to place a working table or a place to put things next to it This shall avoid that the machine is misused as a table www thunder laser com DONGGUAN THUNDER LASER EQUIPMENT CO LTD tech thunder laser com 19 Tel 86 769 82665376 YO THUNDER LASER MARS 90 3 4 Before Installation 1 Take out the sponge around the laser tube Like below 2 Take out the nylon cable ties around the honey comb plate and X axis Remove the transparent bag out of the first mirror mounts the second mirror mounts the first mirror mounts and the standard laser head Then install the laser head Like below E MARS 90 Y A ow y e PS is a set of key and a manual focusing tool for users www thunder laser com DONGGUAN THUNDER LASER EQUIPMENT CO LTD tech thunderlaser com Tel
41. ject and the circle pulse Like below x Work Output Doc user Test Transform Enable rotate engrave Enable feeding Feeding 0 Distance mm 500 Backlash reapy optim Enable offset of Laser X 0 Y 0 Select Output and then tick Enable rotate engrave 1 The Circle pulse is set to 8000 2 The diameter of the target item 9 Select Download click Original and Frame on the display please make sure that the material is in the right location and enough space for working 10 Switch on the cooling system And connect the exhaust system and the air pump to behind of the laser Please check the water cooling system is working properly the water is running into and filling the laser tube Please do not starts your work if laser tube isn t full of water because that may led to laser tube damage due to the high temperature 11 Finally press the Start Pause button in the display to start the engraving or cutting process 12 When you don t need to use the rotary axis attachment to work please turn the rotary axis switch off and remove it out of the working table then reset the laser machine www thunder laser com DONGGUAN THUNDER LASER EQUIPMENT CO LTD tech thunder laser com 60 Tel 86 769 82665376 yl THUNDER LASER MARS 90 4 9 For Laser Engraving The engraving depth can easily be varied thr
42. ll use the single origin logic You can press the Origin key and set the origin and only this origin can become valid If you select Yes the system will use the multiple origin logic and the Origin key on the keyboard become invalid In such a case the parameter of each origin must be set in the menu as follows gt Origin Enable1 2 3 4 after the multiple origin logic is enabled the four origins can independently be prohibited and enabled gt Set Origin 1 2 3 4 after the multiple origin logic is enabled you can stop the cursor at Set as Origin 1 2 3 4 Press the Enter key on the keyboard and the system will take the coordinate figures of current X Y axles as the corresponding ones to the origin 1 2 3 4 gt Next Origin there are such five digits as 0 4 for option which are the origins to be used for the next figure Origin O means the origin set by the Origin key on the panel in the single origin logic 1 4 means the serial number of the origins in the multiple origin logic Next origin can be modified to any one of origin 1 4 so as to control the start location of next work the premise is that the origin is enabled but it can t be modified to origin 0 www thunderlaser com DONGGUAN THUNDER LASER EQUIPMENT CO LTD tech thunder laser com 49 Tel 86 769 82665376 YO THUNDER LASER MARS 90 Once the multiple origin logic is selected and if the serial number of the next origin is 1 and
43. mirror 2 3 The mirror 3 www thunderlaser com DONGGUAN THUNDER LASER EQUIPMENT CO LTD tech thunderlaser com Tel 86 769 82665376 Q THUNDER LASER MARS 90 5 2 3 Cleaning the Beam Combiner eee 1 The beam combiner must be cleaned carefully by using lens cleaning paper lens cleaning cloth to avoid scratching the surface 2 Do not touch the surface of the beam combiner after cleaning 3 For the beam combiner you can clean them directly www thunder laser com tech thunderlaser com Tel 86 769 82665376 DONGGUAN THUNDER LASER EQUIPMENT CO LTD THUNDER LASER MARS 90 5 3 Maintain the X Y Z Rails It is suggested to add lubricant oil or Rust Preventative Grease to the rails screws at least every two weeks www thunder laser com DONGGUAN THUNDER LASER EQUIPMENT CO LTD tech thunderlaser com Tel 86 769 82665376 a THUNDER LASER MARS 90 5 4 Check the Beam Path After being used for a long time the beam path might be deflective This will reduce the efficient of the laser beam or even cause no laser beam At this moment you will need to re adjust the beam path again If you need to know that about adjust the laser beam path of the video on YouTube released by our company and please link to the URL http www vyoutube com watch v pw8Ro2vEEzY www thunder laser com DONGGUAN THUNDER LASER EQUIPMENT CO LTD tech thunder laser com 69 Tel 86 769 82665376
44. om nd DONGGUAN THUNDER LASER EQUIPMENT CO LTD tech thunderlaser com Tel 86 769 82665376 YO THUNDER LASER MARS 90 4 5 How to adjust focus distance 1 If there s no auto focus function for your machine or there s fault for your auto focus you can refer to below instructions about how to adjust focus by manual 1 For standard laser head find the 6mm Acrylic Focus Tool for help to adjust the focus directly like below DWorking Table LA E AAN Material If the focus tool is not the best one for your material you can use the focus ruler for help like below DWorking Table Material S Focus Ruler 2 How to adjust the focus distance by manual Since HR head is very sensitive for focus distance thus we ve tested and made a special focus tool with a best distance for each HR head like below y a Fy x A DWorking Table Material 3 The Best Focus Distance 4 Focus Tool ee EA www thunderlaser com DONGGUAN THUNDER LASER EQUIPMENT CO LTD tech thunderlaser com Tel 86 769 82665376 54 THUNDER LASER MARS 90 3 How to adjust 4 head focus distance 4 laser head is not so sensitive for focus distance you can set the distance about 10mm with the help of focus ruler DWorking Table Material 8 Focus Ruler 2 If there s Auto Focus function for your machine you can adjust the focus by auto 1 Reset Z axis Z axis will move up until touch the A
45. ou can have a try with our HR head HR head focuses the laser beam onto a much more concentrated dot than can be practically achieved with standard optics systems increasing the power density of the laser In order to produce a similar dot size using standard optics the focal length would need to be as short as 3 4mm thus HR head can increase the utility of our laser system Laser dots comparison between standard 2 head and HR head With the help of special design HR head is able to absorb and focus co2 laser beam into a tiny dot thus it s very well for engraving high quality pictures on flat material and precisely for cutting very thin material lf you engrave a normal size photo with an HR head you can also get a better result than the standard head As you can see from the photo even the tiger s eyes are very vivid and the whole photo looks lifelike Lo gt i _ ee SU a s A e a Me AIR IN O a EE Fs ee eee ISA TA 6 et ee a esea a a rs a ew Y AAA API Das 5 h RS s a ARAS p 09 S p AA i 7 cc 1 aed it Standard Head HR Head www thunder laser com DONGGUAN THUNDER LASER EQUIPMENT CO LTD tech thunder laser com 14 Tel 86 769 82665376 THUNDER LASER MARS 90 Samples introduction PEE a ee e ES Sel hy x leo OTE Pa ALLE ETE AAA A a __WWW THUNDERLASER COM_ AER IAEA Pos MAE AT Fak ALLEL
46. ough the laser power or the speed To increase the engraving depth reduce the speed or increase the power setting This way you increase the amount of energy per area unit Engraving too deep however reduces the quality of the details With coated materials the required power depends of the kind and thickness of the coating With power set too high the individual lines become too thick and a sharp picture cannot be achieved The resolution of the graphics should usually be at 500 dpi The dpi setting number of laser dots per inch depends on the material The lower this setting is the lower the resolution of the engraved picture will be This however reduces flaming and increases the energy of a pulse which can improve the overall result e g when engraving some sorts of plastic materials 1 Plastics Plastics for engraving are available in many different colors and thicknesses and with many different coatings and surfaces The majority of available plastics can be well engraved and cut with the laser Plastics with a micro porous surface seem to give the best result because less surface material needs to be removed As most plastic materials have a low melting point a low pip setting should be selected to reduce the danger of melting 2 Acrylic There are two different types of acrylic cast and extruded The cast acrylic becomes white or mat after engraving the extruded acrylic remains clear Use extruded acrylic for engravings that are
47. peration maintenance inspection and repair the switch off procedures that may be provided in the Operation Manual must be observed Safety Information for the User and or Operating Personnel 1 No working methods are permitted that affect the safety of the machine 2 The operator must also ensure that no unauthorized persons work with the machine e g by activating equipment without authorization 3 It is the duty of the operator to check the machine before start of work for externally visible damage and defects and to immediately report changes that appear including behavior during operation that affect the safety 4 The user must provide that the machine is only operated in perfect condition 5 The user must guarantee the cleanness and accessibility at and around the machine by corresponding instructions and controls 6 Principally no safety components may be removed or disabled already here we emphasize the imminent dangers for example severe burns loss of eye sight If the removal of safety components is required during repair and service the replacement of the safety components must be performed immediately after completion of the service and repair activities 7 Preparation retooling change of work piece maintenance and repair activities must www thunderlaser com DONGGUAN THUNDER LASER EQUIPMENT CO LTD tech thunder laser com 10 Tel 86 769 82665376 a THUNDER LASER MARS 90 only performed with equi
48. pment switched off by trained personnel 8 Itis forbidden to perform unauthorized modifications and changes to the machine It is emphasized that any unauthorized modifications to the machine are not permitted for safety reasons www thunder laser com DONGGUAN THUNDER LASER EQUIPMENT CO LTD tech thunder laser com 11 Tel 86 769 82665376 a THUNDER LASER MARS 90 2 2 Laser Safety Information 1 To assess the potential dangers laser systems pose they are classified into 4 safety classes thunder laser MARS 90 is a device of class 4 This is guaranteed by the protective housing and the safety installations Please note that improper operation of the device can override the status of safety class 4 and can cause the emission of harmful radiation 2 This laser engraving system contains a carbon dioxide CO2 laser of class 4 that emits intensive and invisible laser radiation Without safety precautions the direct radiation or even diffuse reflected radiation is dangerous 3 Without safety precautions the following risks exist with exposure to laser radiation Eyes Burns to the cornea Skin Burns Clothing Danger of fire 4 Never try to modify or disassemble the laser and do not try to start up a system that had been modified or disassembled 5 Dangerous radiation exposure can result from the use of operation or adjustment equipment other than that described here and if different operational methods are performed ww
49. rastically To format memory drastically and then all the files in memory will be deleted Total the total running times of all the files 2 U Disk File lf the U disk entry in figure 8 4 1 is pressed the system will show as figure 8 4 3 and the operation method is all the same as figure 8 4 1 Read udisk Copy to memery www thunder laser com DONGGUAN THUNDER LASER EQUIPMENT CO LTD tech thunder laser com 54 Tel 86 769 82665376 a THUNDER LASER MARS 90 eo Read Udisk read the file list in the Udisk e Copy to memory copy the target Udisk file to the memory o Delete delete the selected Udisk file This system supports such file formats of Udisk as FAT32 and FAT 16 but it can identify them when the files are put under the root directory of Udisk The file name of more than 8 characters will automatically be cut out by the system The file name that has only English letters and digits will not show when they are copied to the mainboard The files copied from the mainboard to Udisk will be placed under the root directory of Udisk 4 6 21 Alarm Information of Display When users are operating the system or when the machine is running some alarm information such as water protecting error maybe shows as below Water error Push Enter key or Esc key the system will execute some relative steps www thunder laser com DONGGUAN THUNDER LASER EQUIPMENT CO LTD tech thunder laser com D5 Tel
50. rave but before this you must click the Port setting in the software The size of the graphic does not matter as the printer driver adjusts it to the work piece automatically if requested If you have any questions and also consult the Software Manual for further information 5 Double click the Work in the window of Work then you can modify the parameters such as speed Min Power Max Power ramp Effect Ramp Length Interval and so on 6 Select Download you can change the file name If you don t change the file name that will be the default name for default and will be covered the last file 7 Click Original and Frame on the display please make sure that the material is in the right location and there is enough space for working www thunder laser com DONGGUAN THUNDER LASER EQUIPMENT CO LTD tech thunder laser com 56 Tel 86 769 82665376 O THUNDER LASER MARS 90 8 Please check the water cooling system is working properly the water is running into and filling the laser tube Please do not start your work if the laser tube isn t full of water because that may led to laser tube damage due to the high temperature 9 Finally press the Start Pause button in the display to start the engraving process 10 While the laser is engraving you can generate the next graphic 11 When the engraving is complete the laser machine will give out the notification sound and the laser head will go
51. red successfully You can return to the previous menu by press the Enter key 4 6 15 Auto Focus When the cursor stops at Auto Focus press the Enter key to search for the focus When there is z axes and the z axes reset function is enabled the auto focusing is valid press the Esc key to return the prior menu 4 6 16 Language The item Language helps you to select a appropriate langue which is displayed on the www thunder laser com DONGGUAN THUNDER LASER EQUIPMENT CO LTD tech thunder laser com 50 Tel 86 769 82665376 a THUNDER LASER MARS 90 pane Simplify Tradition English 4 6 17 IP Setup When the green block is on this item push the Enter key to show as below IP address Gateway Press Z U move item Modified press Enter Push Z U key to move the changing item then push X keys and Y keys to change the value when all the IP value and the Gateway value are changed push Enter key to validate the change or Esc key to invalidate the change 4 6 18 Diagnoses If the Diagnoses item is pressed the system will show as below www thunderlaser com DONGGUAN THUNDER LASER EQUIPMENT CO LTD tech thunder laser com 51 Tel 86 769 82665376 a THUNDER LASER MARS 90 X Limit m1 X Limit m Y Limit Y Limit Z Limit Z Limit U Limit U Limit _ Water prot1 _ Water prot2 Open prot rear This interfa
52. rify whether harmful materials can be generated and whether the filter equipment of the exhaust system is suitable for the harmful materials We emphasize that it is the responsibility of the user to consider the national and regional threshold values for dust fogs and gases when selecting the filters and the exhaust system The values for the maximum workplace concentration must not be exceeded Please refer to the manual of the exhaust system on how and in what intervals you need to replace filters PVC polyvinyl chloride must under no circumstances be processed with the laser Should you have further questions before starting work please feel free to write us an email at tech thunderlaser com www thunder laser com DONGGUAN THUNDER LASER EQUIPMENT CO LTD tech thunder laser com 13 Tel 86 769 82665376 Q THUNDER LASER MARS 90 2 4 Warning and Information Labels The warning and information labels are attached in such positions of the device that could represent a source of danger during set up and operation Therefore follow the information on the labels If labels are lost or damaged they must be replaced immediately INVISIBLE LASER RADIATION AVOID EYE OR SKIN EXPOSURE TO DIRECT OR SCATTERED RADIATION CLASS IV LASER www thunder laser com DONGGUAN THUNDER LASER EQUIPMENT CO LTD tech thunderlaser com Tel 86 769 82665376 THUNDER LASER MARS 90 INVISIBLE LASER RADIATION
53. rs show as below Speed 400 mm s MinPowerl1 22 0 MinPower 2 30 0 30 MaxPowerl MaxPower2 Press Z U move item Modified press Enter User can push Z U Keys to move the green block on the intent parameter then he could change the parameter if needed OK to validate the change and Esc to invalidate the change 4 6 6 Z U Key The Z U key can be pressed when the system is idle or the work is finished On pressing this key it will show some entries in the following interface www thunderlaser com DONGGUAN THUNDER LASER EQUIPMENT CO LTD tech thunder laser com 46 Tel 86 769 82665376 a THUNDER LASER MARS 90 Z move Language U move IP setup Axis reset Diagnoses Manual Set Screen Origin Laser Set zme J Origin set Set Fact Para Def Fact Para Auto Focus Press up and down arrow keys to move the green block to the anticipant item and then push the Enter key to display the sub menu 4 6 7 Z Move When the green block is on Z Move item to move the Z axis table up and down by press left and right arrow keys then press ESC to go back to normal x amp Y axis control 4 6 8 U Move When the green block is on U Move item to move the Z axis table up and down by press left and right arrow keys 4 6 9 Axis Reset When the green block is on this item push the Enter key to show as below XY axis reset X axis reset Y axis reset
54. the display and then you have finished the device connection Like below www thunder laser com DONGGUAN THUNDER LASER EQUIPMENT CO LTD tech thunder laser com 58 Tel 86 769 82665376 YO THUNDER LASER 4 Before you mount the object into the rotary axis attachment measure the diameter of the object at the position to be engraved with a sliding caliper or a similar tool Write down this value And how to set the parameter about Circle Pulse please refer to following the picture indicates Like below small gear diameter of item big gear Diameter of item 80mm OO Gear ratio big gear small gear 2 Microstep Driver See the settings of your motor driver D The subdivision of our motor driver is set to 4000 the Circle Pulse is 4000x2 5 Adjust and fix the slider to make the work piece fitting into the rotary axis attachment 6 Now switch on the laser and wait until the referencing is finished Position the working head over the object at the position where you want to engrave Now focus the object with the focus tool or by auto focus 7 Generate a graphic with the help of the graphics software The graphics size must be adjusted until less than the dimensions of the work piece www thunder laser com tech thunderlaser com Tel 86 769 82665376 DONGGUAN THUNDER LASER EQUIPMENT CO LTD a THUNDER LASER MARS 90 8 Select Output and then input the diameter of the ob
55. urrent if you need to repair please contact with professional maintenance staff 19 PC connection port USB This USB is for connecting computer www thunder laser com DONGGUAN THUNDER LASER EQUIPMENT CO LTD tech thunder laser com 32 Tel 86 769 82665376 Oe THUNDER LASER MARS 90 20 U disk connection port USB 21 Main power switch 22 Laser power switch 23 Power supply socket To connect the main power and the extend power according the label information And in the main power socket have the fuses 24 Laser tube cover There installed the laser tube red dot pointer device beam combiner and the first reflective mirror inside 25 Exhaust hose This is for installing the exhaust device 26 Blow air port This port is for connecting hoses of the air compressor 2 Water in and water out 28 Rear door 29 Manufacture s Label Shows important data of the machine like serial number or manufacturing date etc www thunder laser com DONGGUAN THUNDER LASER EQUIPMENT CO LTD tech thunder laser com 33 Tel 86 769 82665376 YO THUNDER LASER MARS 90 4 2 ON OFF Switch Switches the mains and the laser supply power ON OFF The following conditions must be fulfilled for correct start up Unrestricted freedom of motion of the mechanics No materials under the engraving table Protection covers closed When turn on the power of machine and note that turn on the main switch first and then the laser supply po
56. uto focus switch or the machinery limit switch here the coordinate 0 0 please refer to Pic 1 2 Set a correct focus distance please refer to pic 2 3 Select Auto focus on display panel then the table will auto focus directly please refer to pic 3 www thunderlaser com FS DONGGUAN THUNDER LASER EQUIPMENT CO LTD techOthunderlaser com 40 Tel 86 769 82665376 THUNDER LASER Auto home x Auto home Y Auto home z Auto home LU H Go Scale para Go scale mode Go scale blank imm El Other Array processing Return position Focus depthimm Backlash ror Backlash imm Mo Mo Close laser 0 000 Bi dir Array Absolute Origit 3 000 0 000 0 000 r open save Read Jue 3 t Z move Language IP setup Axis reset Diagnoses Manual Set Screen Origin Laser Set Origin set Set Fact Para Def Fact Para Auto Focus www thunderlaser com tech thunder laser com l At NR f JD Tel 86 769 82665376 MARS 90 DONGGUAN THUNDER LASER EQUIPMENT CO LTD a THUNDER LASER MARS 90 4 6 How to use the display 4 6 1 Function of the Buttons THUNDERLASER SYSTEM ETT KZ cXx sST NN iii ZNN QQ CL Lf ESSSSSS88Y O 888 SSA ONG Mi DLL HT MADURAR A A LAA A AAANASSSE 7Z YY 0 PI WAAR EET AAAA AAAA RASS S S E E E E EEE AAAA Min Max Start enn Arrow buttons control the movement of th
57. vidual points of the Operation Manual Operation of the system is only permitted with equipment and spare parts supplied or listed in the spare parts and consumables lists Auxiliary equipment must be adjusted to the base machine any queries to dealer or manufacturer The following symbols are used for easier understanding of the Operation Manual If the Operation Manual is not observed this area represents a particular danger for the operating personnel or the personnel responsible for maintenance Caution This component is under voltage In these areas strictly observe the safety instructions regarding electricity Care is to be taken in particular during maintenance and repair work Caution In this area pay attention to the possible dangers of the laser beam Tips Note or information on individual components of the device that simplify the use or make it more understandable www thunderlaser com DONGGUAN THUNDER LASER EQUIPMENT CO LTD tech thunder laser com 5 Tel 86 769 82665376 yl THUNDER LASER MARS 90 1 2 Designated The THUNDER LASER MARS 90 is used for engraving and cutting of signs stamps and suchlike A wide variety of materials such as rubber acrylic coated metal tin special steel anodized aluminum cork cardboard glass leather marble several plastics and wood can be processed on the laser 1 The engraving process must only be performed with a perfectly adjusted machine 2 For cutt
58. w thunder laser com DONGGUAN THUNDER LASER EQUIPMENT CO LTD tech thunder laser com 12 Tel 86 769 82665376 yl THUNDER LASER MARS 90 2 3 Safety Precautions when Operating the Device In your thunder laser MARS 90 a closed safety system is integrated which immediately switches off the power to the laser tube when the protection cover is opened Consequently an incomplete engraving can occur if the cover is opened during operation Therefore first press the PAUSE button if you want to interrupt an engraving process Please remember the following safety precautions when working with this device A fire extinguisher must always be handy as the laser beam can ignite flammable materials Do not store any flammable materials in the inside of the device or in the immediate vicinity of the device Particularly leftovers of produced materials have to be removed to prevent fire hazard Unsupervised operation of the system is not permitted Because of their low absorption many metals in particular un coated aluminum copper silver and gold cannot be processed with the laser and lead to high reflections of the laser beam Such materials must not be inserted into the beam as a directed reflection could destroy the protection cover Adjustment of the beam path must be performed only by especially trained personnel An improper setting can lead to uncontrolled emission of the laser radiation Before processing materials the user must ve
59. we advise customs consult the following thinking before encounter problems and hope customs can revise our thinking at any time Laser head impact Limit switch while resetting Here are the fault factors 1 Wrong pulse settings 2 Limit switch type mismatch the laser controller 3 Wiring mistake Here are the solutions Step 1 Wrong pulse setting Resetting the pulse equivalent for how to reset please refer to the lesson why cutting size doesn t match design size Step 2 Limit switch type mismatch laser controller Our Thunder laser controller support NPN NO mechanical switch or sensor switch only Step 3 Wiring mistake Please refer to following diagram for how to wiring the limit switch 1 Mechanical switch 2 sensor switch 24V GND O X Limit Limit Please set the limit switch singal to Low Level Effect in software If you want to know more information about troubleshooting and you can visit our website http www thunderlaser com technical support troubleshooting html If you need any other help just contact with us by sending e mail to tech thunderlaser com End www thunder laser com DONGGUAN THUNDER LASER EQUIPMENT CO LTD tech thunder laser com 12 Tel 86 769 82665376 a THUNDER LASER MARS 90 Chapter 6 The Characteristics of Thunder Laser 1 1 Laser heads for application Different laser head owns different focal distance and laser dot size thus they were used for differ
60. wer lf all covers are closed immediately after being switched on the device starts the referencing process When the referencing process is completed correctly an acoustic signal sounds and the device is ready for operation The operation panel will display the home screen when the laser is completed resets Before switching on the device the user must make sure that no objects of any kind are located inside the operating space which could limit or obstruct the mechanics of the device Tips When switching off the mains supply all processing data is lost www thunder laser com DONGGUAN THUNDER LASER EQUIPMENT CO LTD tech thunder laser com 34 Tel 86 769 82665376 ys THUNDER LASER MARS 90 4 3 How to use the TL Timer The TL Timer is an additional tool for laser machines It will control laser machines periphery like exhaust fan air values warning lights pneumatic lifts electrical locks and lost of other stuff automatically This will increase the ease of use of your laser machine Please note the different types of connection which makes the TL Timer able to work with each kind of laser controller Operation Normal use The TL Timer gets activated by a control signal from laser controller For this case the red LED lights up and all 4 relays will be activated until the signal from controller gets turned off Without control signal the 4 relays will stay turned on until a given delay time has expired Each
61. y are pushed www thunder laser com DONGGUAN THUNDER LASER EQUIPMENT CO LTD tech thunder laser com 44 Tel 86 769 82665376 a THUNDER LASER MARS 90 4 6 3 Speed Key Push the Speed key when the screen is on the main interface it will show as below HOO om Modified press Enter Push the X Keys to move the cursor in the numeral area and push the Y keys to change the value then push the Enter key to save the change push the Esc key to invalidate the change 4 6 4 Max Min Power Keys Push the Max Power or the Min Power keys when the screen is on the main interface it will show as below MaxPowerl 30 0 MaxPower2 30 01 Press Z U move item Modified press Enter MinPowerl 30 0 MinPower 2 30 0 Press Z U move item Modified press Enter When Z U key is pushed the green block can move up and down to denote the changing item then Y keys and X keys can be used to change the value www thunderlaser com DONGGUAN THUNDER LASER EQUIPMENT CO LTD tech thunder laser com 45 Tel 86 769 82665376 a THUNDER LASER MARS 90 4 6 5 Set the Layer Parameters After selecting a file to preview on the main interface user can push Enter key to let the cursor move to the first layer then Y Keys can be pushed to select the intent layer on that time user can push Enter key to check the selected layer s paramete
62. yl THUNDER LASER MARS 90 THUNDER LASER SYSTEMS y Wy MARS 90 de 1 1 User s manual for MARS 90 www thunderlaser com tech thunderlaser com April 27 2014 www thunder laser com DONGGUAN THUNDER LASER EQUIPMENT CO LTD tech thunderlaser com 1 Tel 86 769 82665376 THUNDER LASER MARS 90 Introduction This manual has been designated as the thunder laser systems laser cutting machine installation and user guide The manual is divided into five chapters Including general information instructions safety instructions the key components of every laser cutting systems and the installation steps operation instructions and maintenance instructions from THUNDERLASER Company Frist it should be emphasized that the installation of each system must meet the requirements and make it consistent with the installation requirements of THUNDERLASER If not the machine will not working properly poor performance life shortened maintenance costs increased and even machine damage The note is for getting a specific requirement of system installation and we hope every customer try to understand these notes before installation and usage thus you can correctly install and use If you meet any installation problems you can contact our technical staff and customer service staff At the same time you can also refer to the machine installation video that we posted on youtube The specific URL is www thunderlaser com

User`s manual for MARS-90

Contents

Download Pdf Manuals

Related Search

Related Contents