GT11H-CNB-37S - User`s Manual JY997D24601-D (04.13
Contents
1. handle it as industrial waste avoid impacts larger than those specified in this manual Failure to do so may cause failures in the unit After transportation verify the operations of the unit Associated Manuals The following manuals are relevant to this product When these loose manuals are required please consult with our local distributor Manual Number Manual name Model Code GT14 Handy GOT User s Manual Describes the Handy GOT hardware relevant content such as part names external JY997D50201 Hardware Utility Connection 1 2 2 2 dimensions mounting power supply wiring specifications and introduction to option JY997D50202 sold separately devices O9R825 GT11 Handy GOT User s Manual Describes the Handy GOT hardware relevant content such as part names external JY997D20101 Hardware Utility Connection 1 2 2 2 dimensions mounting power supply wiring specifications and introduction to option JY997D20102 sold separately devices 09R817 For details of a PLC to be connected refer to the PLC user s manual respectively Bundled Items Bundled item Quantity Mounting fitting 1 Mounting screw M3 x8 3 CONNECTOR CONVERSION BOX GT11H CNB 37S User s Manual This manual 1 1 Features The Connector Conversion Box relays the GOT s external D Sub 37 pin connector to the power supply switch and the PLC s connector and terminal block while enabling users to operate the Handy GOT outside the enclosure Handy GOT GT12. s connector and terminal block while enabling users to operate the Handy GOT outside the enclosure Handy GOT GT14 Handy GT11 Handy Panel face To power supply switch Rats IEC eeeogoooeggaoeae External cable option toptien Relay cable for connection between PLCs option N Connector Conversion Box GT11H CNB 37S blank cable connection fault e When unplugging the cable connected to the unit do not hold and pull the cable portion Doing so can cause the unit or cable to be damaged or can cause a malfunction due to a cable connection fault 2 Part Name 4 2 Mounting with a mounting bracket The name and the function of each part of the Connector Conversion Box are described below e Front Panel 1 Connector for Handy GOT D Sub 37 pin female 5 Connects a Handy GOT through an external connection cable 2 Power switch Supplies the power to the Handy GOT When this switch is set to ON the power is supplied Turn off the power when attaching or detaching the Handy GOT 3 Mounting hole for M3 screw Allows to fix the Connector Conversion Box on the panel face directly or through a mounting bracket e Back Panel 4 Terminal block for power supply and operation switches Connects the 24V DC power supply and operation switches SW1 to SW6 of the Handy GOT Terminal block for connection M3 t
3. to fix the Connector Conversion Box on the panel face directly or K mS ler Ze Bs through a mounting bracket 4 RIF rel g e Back Panel S R Is ol es 4 Terminal block for power supply and operation switches 4 5 oJ 1 DE a Connects the 24V DC power supply and operation switches SW1 to M4 screw and nut AI SW6 of the Handy GOT x 3 sets Terminal block for connection M3 terminal screw provided cover prepared by user ae 5 Terminal block for emergency stop switch grip switch keylock switch k Mounting Connects the emergency stop switch ES 1 ES 2 ES 3 grip switch se Bracket DSW 1 DSW 2 and keylock switch KSW 1 KSW 2 ial a ial Terminal block for connection M3 terminal screw provided cover Unit mm inch 6 Connector for PLC RS 422 D Sub 9 pin female Connects the PLC through a PLC cable RS 422 and RS 232 are not available simultaneously A A Connector model name 17JE 13090 37D23A DDK 4 3 Installation requirements for the rear face of enclosure 3 1 For GT11 Handy ES 3 is not available ta 7 Connector for PLC RS 232 D Sub 9 pin male Make sure that interfering objects are not located within 100mm 3 93 from the rear face so that the connector of a PLC cable is not hindered Connects the PLC through a PLC cable To wire the terminal block keep a space of 25mm 0 98 or more on both sides of the Connector Conversion Box RS 422 and RS 232 are not available simultaneo
4. touch switch s remains active Doing so can cause a failure malfunction injury or fire This may confuse an operator in thinking that the GOT is in screensaver e Do not touch the conductive and electronic parts of the unit directly mode who then tries to release the GOT from this mode by touching the Doing so can cause a unit malfunction or failure display section which may cause a touch switch to operate e The cables connected to the unit must be run in ducts or clamped Note thatthe following Orn WE AOT NORE packighit goes out Not doing so can cause the unit or cable to be damaged due to the dangling The POWER LED flickers green orange and the monitor screen appears motion or accidental pulling of the cables or can cause a malfunction due to a STARTUP MAINTENANCE PRECAUTIONS WARNING e When power is on do not touch the terminals Doing so can cause an electric shock or malfunction e Before starting cleaning or terminal screw retightening always switch off the power externally in all phases Not switching the power off in all phases can cause a unit failure or malfunction Undertightening can cause a short circuit or malfunction Overtightening can cause a short circuit or malfunction due to the damage of the screws or unit STARTUP MAINTENANCE PRECAUTIONS CAUTION TRANSPORTATION PRECAUTIONS CAUTION e The Connector Conversion Box is a precision instrument During transportation e When dis
5. 4 Handy GT11 Handy Panel face To power supply switch WEG Mette SLEE e External cable option toptien Relay cable for connection between PLCs option N Connector Conversion Box GT11H CNB 37S 2 Part Name 4 2 Mounting with a mounting bracket The name and the function of each part of the Connector Conversion Box are described below 1 Attaching a mounting bracket 2 Mounting on the panel face Attach the provided mounting bracket to the Connector Conversion Box Mount the Connector Conversion Box on the panel face e Front Panel Drill screw holes on the panel face as follows 1 Connector for Handy GOT D Sub 37 pin female Front Panel Back Panel C tsa Handy GOT th h ji i bi 2 onnec sa andy rough an external connection cable Connecter Conversion Box 2 Power switch Supplies the power to the Handy GOT Drill 3 4 5 y Terminal name ES 3 1 When this switch is set to ON the power is supplied Mounting bracket Turn off the power when attaching or detaching the Handy GOT accessory D S ae Oe Gg 3 Mounting hole for M3 screw f 4 ig SAM sg Allows
6. OT 1000 10 to 90 RH non condensing The wet bulb temperature is 39 C or less In conforms to JIS B3502 and IEC61131 2 5 to 9Hz Half amplitude 3 5 mm 9 to 150Hz Acceleration 4 9m s2 10 times sweeping in each of X Y and Z directions Operating ambient humidity Vibration resistance Must be free of lamp black corrosive gas flammable gas or excessive amount of electroconductive dust particles and must be no direct sunlight Same as for saving Operating atmosphere External Dimensions 82 3 22 37 5 1 47 Terminal name ES 3 1 PERE H IS ES 2 3 es 3 1 6 2 1 2 com 2 1 4 Dsw psw ksw KSW Es 2 Es es psw Dsw Ksw 1 sw sw sw sw com 2 elelelelelele 113 4 44 Weight about 0 17kg 19 5 0 76 Unit mm inch 18 0 7 1 For GT11 Handy ES 3 is not available 4 Installation The Connector Conversion Box can be installed on the panel face directly or with mounting bracket offered as an accessory 4 1 Direct mounting on the panel face 1 Direct mounting on the panel face 2 Drill a mounting slot of the following size on the panel face Mounting on the panel face Fit the Connector Conversion Bo
7. TENANCE PRECAUTIONS NWARNING e When power is on do not touch the terminals Doing so can cause an electric shock or malfunction e Before starting cleaning or terminal screw retightening always switch off the power externally in all phases Not switching the power off in all phases can cause a unit failure or malfunction Undertightening can cause a short circuit or malfunction Overtightening can cause a short circuit or malfunction due to the damage of the screws or unit STARTUP MAINTENANCE PRECAUTIONS CAUTION e Do not disassemble or modify the unit Doing so can cause a failure malfunction injury or fire e Do not touch the conductive and electronic parts of the unit directly Doing so can cause a unit malfunction or failure e The cables connected to the unit must be run in ducts or clamped Not doing so can cause the unit or cable to be damaged due to the dangling motion or accidental pulling of the cables or can cause a malfunction due to a cable connection fault e When unplugging the cable connected to the unit do not hold and pull the cable portion Doing so can cause the unit or cable to be damaged or can cause a malfunction due to a cable connection fault TRANSPORTATION PRECAUTIONS CAUTION e The Connector Conversion Box is a precision instrument During transportation e When disposing of the product handle it as industrial waste DISPOSAL PRECAUTIONS CAUTION When disposing of the product
8. a space of 25mm 0 98 or more on both sides of the Connector Conversion Box Thread depth 7 6 0 23 25 0 98 25 0 98 Panel face u 100 3 93 Bor Unit mm inch 5 Cautions for use For the emergency stop SW the b contact type is used When the Handy GOT is installed and removed with the connector the switch changes ON to OFF when removed which is the same as the state where the emergency switch is pressed Design such as configuring a parallel circuit outside must be taken into consideration to avoid emergency stop while the Handy GOT is being removed Handy GOT GT14 Handy GT11 Handy Used as control signals of external device power ON OFF This manual confers no industrial property rights or any rights of any other kind nor does it confer any patent licenses Mitsubishi Electric Corporation cannot be held responsible for any problems involving industrial property rights which may occur as a result of using the contents noted in this manual Warranty Mitsubishi will not be held liable for damage caused by factors found not to be the cause of Mitsubishi opportunity loss or lost profits caused by faults in the Mitsubishi products damage secondary damage accident compensation caused by special factors unpredictable by Mitsubishi damag
9. an cause a short circuit or malfunction Overtightening can cause a short circuit or malfunction due to the damage of the screws or unit Safety Precaution Read these precautions before using Before using this product please read this manual and the relevant manuals introduced in this manual carefully and pay full attention to safety to handle the product correctly The precautions given in this manual are concerned with this product In this manual the safety precautions are ranked as and A CAUTION Indicates that incorrect handling may cause hazardous N WARNING conditions resulting in death or severe injury Indicates that incorrect handling may cause hazardous NCAUTION conditions resulting in medium or slight personal injury or physical damage Depending on circumstances procedures indicated by CAUTION may also be linked to serious results In any case it is important to follow the directions for usage TEST OPERATION PRECAUTIONS N WARNING e Before performing the test operations of the user creation monitor screen such as turning ON or OFF bit device changing the word device current value changing the settings or current values of the timer or counter and changing the buffer memory current value read through the manual carefully and make yourself familiar with the operation method During test operation never change the data of the devices which are used to perform significant operation for the sy
10. be the cause of Mitsubishi opportunity loss or lost profits caused by faults in the it with four M3 screws prepared by user In the Connector Conversion Box thread of M3 6mm 0 23 in depth is cut in each mounting hole Prepare four M3 mounting screws separately while con Mitsubishi products damage secondary damage accident compensation caused by special factors unpredictable by Mitsubishi damages to products 0 7 28 1 1 18 0 7 idari a l i mi sidering the thickness of the panel face Connector Conversion Box Parallel circuit other than Mitsubishi products and to other duties rill 4 3 E Connector Thread depth o XS Conversion Le 0 23 1 For GT11 Handy ES 3 is not available AN For safe use 4 Y Box oO l A 4 o X e This product has been manufactured as a general purpose part for general i lt 3 industries and has not been designed or manufactured to be incorporated in S9 P ae F a device or system used in purposes related to human life ooo Be P e Before using the product for special purposes such as nuclear power electric N g Zz if power aerospace medicine or passenger movement vehicles consult with 2 as Mitsubishi Electric P e This product has been manufactured under strict quality control However oe j 4 A S when installing the product where major accidents or losses could occur if the ae TA _ ier eR product fails install appropriate backup or failsafe functions in
11. erminal screw provided cover 5 Terminal block for emergency stop switch grip switch keylock switch Connects the emergency stop switch ES 1 ES 2 ES 3 grip switch DSW 1 DSW 2 and keylock switch KSW 1 KSW 2 Terminal block for connection M3 terminal screw provided cover 6 Connector for PLC RS 422 D Sub 9 pin female 7 Connects the PLC through a PLC cable RS 422 and RS 232 are not available simultaneously Connector model name 17JE 13090 37D23A DDk 7 Connector for PLC RS 232 D Sub 9 pin male Connects the PLC through a PLC cable RS 422 and RS 232 are not available simultaneously Connector model name JES 9P 2A3A JST Back Panel Front Panel 2 4 Terminal name ES 3 1 3 3 eS Ksw ES 1 2 2 com 2 1 2 2 Es Es psw psw ksw ksw ES elelelele Es Es Dsw psw 1 1 1 HOAVQACO COC elelslelele b ea elo 3 6 1 For GT11 Handy ES 3 is not available 3 Specifications General Specifications Applicable GOTs Model name GT1455HS QTBDE GT1450HS QMBDE GT1155HS QSBD GT1150HS QLBD Abbreviations GT14 Handy GOT GT11 Handy GOT Item Specifications Operating ambient temperature 0 to 55 C G
12. es to products other than Mitsubishi products and to other duties e This product has been manufactured as a general purpose part for general industries and has not been designed or manufactured to be incorporated in a device or system used in purposes related to human life Parallel circuit Connector Conversion Box 1 For GT11 Handy ES 3 is not available e Before using the product for special purposes such as nuclear power electric power aerospace medicine or passenger movement vehicles consult with Mitsubishi Electric e This product has been manufactured under strict quality control However when installing the product where major accidents or losses could occur if the product fails install appropriate backup or failsafe functions in the system MITSUBISHI ELECTRIC CORPORATION HEAD OFFICE TOKYO BUILDING 2 7 3 MARUNOUCHI CHIYODA KU TOKYO 100 8310 JAPAN HIMEJI WORKS 840 CHIYODA CHO HIMEJI JAPAN
13. functions Please make sure to ground FG terminal of the Connector Conversion Box power supply section by applying 100 or less which is used exclusively for the GOT Not doing so may cause an electric shock or malfunction Correctly wire the Connector Conversion Box power supply section after confirming the rated voltage and terminal arrangement of the GOT Not doing so can cause a fire or failure Exercise care to avoid foreign matter such as chips and wire offcuts entering the GOT Not doing so can cause a fire failure or malfunction WIRING PRECAUTIONS CAUTION e Plug the communication cable into the connector of the connected unit and tighten the mounting and terminal screws in the specified torque range Undertightening can cause a short circuit or malfunction Overtightening can cause a short circuit or malfunction due to the damage of the screws or unit TEST OPERATION PRECAUTIONS N WARNING e Before performing the test operations of the user creation monitor screen such as turning ON or OFF bit device changing the word device current value changing the settings or current values of the timer or counter and changing the buffer memory current value read through the manual carefully and make yourself familiar with the operation method During test operation never change the data of the devices which are used to perform significant operation for the system False output or malfunction can cause an accident STARTUP MAIN
14. ions resulting in medium or slight personal injury or physical damage Depending on circumstances procedures indicated by A CAUTION may also be linked to serious results In any case it is important to follow the directions for usage DESIGN PRECAUTIONS WARNING e Some failures of the GOT or cable may keep the outputs on or off An external monitoring circuit should be provided to check for output signals which may lead to a serious accident Not doing so can cause an accident due to false output or malfunction e f a communication fault including cable disconnection occurs during monitoring on the GOT communication between the GOT and PLC CPU is suspended and the GOT becomes inoperative A system where the GOT is used should be configured to perform any significant operation to the system by using the switches of a device other than the GOT on the assumption that a GOT communication fault will occur Not doing so can cause an accident due to false output or malfunction e Do not use the GOT as the warning device that may cause a serious accident An independent and redundant hardware or mechanical interlock is required to configure the device that displays and outputs serious warning Failure to observe this instruction may result in an accident due to incorrect output or malfunction e Incorrect operation of the touch switch s may lead to a serious accident if the GOT backlight is gone out When the GOT backlight goes ou
15. mergency stop while the Handy GOT is being removed a z Handy GOT 4 1 GT14 Handy GT11 Handy 2 1 2 Es Es psw psw ksw ksw ES elelelelelele sw sw sw sw ES ES jcom 2 1 PRESI 113 4 44 ele Weight about 0 17kg 7 9 5 0 76 Unit mm inch Used as 1 For GT11 Handy ES 3 is not available control 3 signals of This manual confers no industrial property rights or any rights of any other kind 4 Installation external nor does it confer any patent licenses Mitsubishi Electric Corporation cannot be device power ON OFF held responsible for any problems involving industrial property rights which may The Connector Conversion Box can be installed on the panel face directly or with mounting bracket offered as an accessory occur as a result of using the contents noted in this manual 4 1 Direct mounting on the panel face 1 Direct mounting on the panel face 2 Mounting on the panel face Warranty Drill a mounting slot of the following size on the panel face Fit the Connector Conversion Box from the back side of the panel face and fix Mitsubishi will not be held liable for damage caused by factors found not to
16. posing of the product handle it as industrial waste DISPOSAL PRECAUTIONS CAUTION When disposing of the product handle it as industrial waste avoid impacts larger than those specified in this manual Failure to do so may cause failures in the unit After transportation verify the operations of the unit Associated Manuals The following manuals are relevant to this product When these loose manuals are required please consult with our local distributor Manual Number Manual name Model Code GT14 Handy GOT User s Manual Describes the Handy GOT hardware relevant content such as part names external JY997D50201 Hardware Utility Connection 1 2 2 2 dimensions mounting power supply wiring specifications and introduction to option JY997D50202 sold separately devices O9R825 GT11 Handy GOT User s Manual Describes the Handy GOT hardware relevant content such as part names external JY997D20101 Hardware Utility Connection 1 2 2 2 dimensions mounting power supply wiring specifications and introduction to option JY997D20102 sold separately devices 09R817 For details of a PLC to be connected refer to the PLC user s manual respectively Bundled Items Bundled item Quantity Mounting fitting 1 Mounting screw M3 x8 3 CONNECTOR CONVERSION BOX GT11H CNB 37S User s Manual This manual 1 1 Features The Connector Conversion Box relays the GOT s external D Sub 37 pin connector to the power supply switch and the PLC
17. side JY997D24601D B EA JAPANESE S E ENGLISH a MITSUBISHI CONNECTOR CONVERSION BOX GT11H CNB 37S User s Manual Manual Number JY997D24601D GRAPHIC OPERATION TERMINAL GOTIOoop This manual describes the part names dimensions mounting and specifications of the product Before use read this manual and manuals of relevant products fully to acquire proficiency in handling and operating the product Make sure to learn all the product information safety information and precautions And store this manual in a safe place so that you can take it out and read it whenever necessary Always forward it to the end user Registration The company name and the product name to be described in this manual are the registered trademarks or trademarks of each company Effective Apr 2013 Specifications are subject to change without notice 2008 Mitsubishi Electric Corporation Safety Precaution Read these precautions before using Before using this product please read this manual and the relevant manuals introduced in this manual carefully and pay full attention to safety to handle the product correctly The precautions given in this manual are concerned with this product In this manual the safety precautions are ranked as and A CAUTION Indicates that incorrect handling may cause hazardous N WARNING conditions resulting in death or severe injury Indicates that incorrect handling may cause hazardous NCAUTION condit
18. stem False output or malfunction can cause an accident DESIGN PRECAUTIONS WARNING e Some failures of the GOT or cable may keep the outputs on or off An external monitoring circuit should be provided to check for output signals which may lead to a serious accident Not doing so can cause an accident due to false output or malfunction e f a communication fault including cable disconnection occurs during monitoring on the GOT communication between the GOT and PLC CPU is suspended and the GOT becomes inoperative A system where the GOT is used should be configured to perform any significant operation to the system by using the switches of a device other than the GOT on the assumption that a GOT communication fault will occur Not doing so can cause an accident due to false output or malfunction e Do not use the GOT as the warning device that may cause a serious accident An independent and redundant hardware or mechanical interlock is required to configure the device that displays and outputs serious warning Failure to observe this instruction may result in an accident due to incorrect output or malfunction e Incorrect operation of the touch switch s may lead to a serious accident if the GOT backlight is gone out When the GOT backlight goes out the POWER LED flickers green orange and the display section turns black and causes the monitor screen to appear e Do not disassemble or modify the unit blank while the input of the
19. subishi Electric Corporation MOUNTING PRECAUTIONS WARNING e Make sure to turn off the Connector Conversion Box s power before attaching or detaching it to from the GOT Failure to do so may cause unit failure or malfunctions MOUNTING PRECAUTIONS CAUTION GRAPHIC OPERATION TERMINAL GOTico9o e Use the Connector Conversion Box within the generic environment specifications described in this manual If the product is used in such conditions electric shock fire malfunctions deterioration or damage may occur WIRING PRECAUTIONS WARNING e Be sure to shut off all phases of the external power supply used by the system before wiring Failure to do so may result in an electric shock product damage or malfunctions Please make sure to ground FG terminal of the Connector Conversion Box power supply section by applying 100 or less which is used exclusively for the GOT Not doing so may cause an electric shock or malfunction Correctly wire the Connector Conversion Box power supply section after confirming the rated voltage and terminal arrangement of the GOT Not doing so can cause a fire or failure Exercise care to avoid foreign matter such as chips and wire offcuts entering the GOT Not doing so can cause a fire failure or malfunction WIRING PRECAUTIONS CAUTION e Plug the communication cable into the connector of the connected unit and tighten the mounting and terminal screws in the specified torque range Undertightening c
20. t the POWER LED flickers green orange and the display section turns black and causes the monitor screen to appear blank while the input of the touch switch s remains active This may confuse an operator in thinking that the GOT is in screensaver mode who then tries to release the GOT from this mode by touching the display section which may cause a touch switch to operate Note that the following occurs on the GOT when the backlight goes out The POWER LED flickers green orange and the monitor screen appears blank DESIGN PRECAUTIONS CAUTION e Do not bundle the control and communication cables with main circuit power or other wiring Run the above cables separately from such wiring and keep them a minimum of 100mm 3 94in apart Not doing so noise can cause a malfunction MOUNTING PRECAUTIONS WARNING e Make sure to turn off the Connector Conversion Box s power before attaching or detaching it to from the GOT Failure to do so may cause unit failure or malfunctions MOUNTING PRECAUTIONS CAUTION e Use the Connector Conversion Box within the generic environment specifications described in this manual If the product is used in such conditions electric shock fire malfunctions deterioration or damage may occur WIRING PRECAUTIONS WARNING e Be sure to shut off all phases of the external power supply used by the system before wiring Failure to do so may result in an electric shock product damage or mal
21. the system Panel cut area r face i 100 3 93 MITSUBISHI ELECTRIC CORPORATION Unit mm inch ee ae 3 93 HEAD OFFICE TOKYO BUILDING 2 7 3 MARUNOUCHI CHIYODA KU TOKYO 100 8310 JAPAN M3 screw x 4 pieces prepared by user Unit mm inch HIMEJ WORKS 840 CHIYODA CHO HIMEJI JAPAN side JY997D24601D B EA JAPANESE S E ENGLISH a MITSUBISHI CONNECTOR CONVERSION BOX GT11H CNB 37S DESIGN PRECAUTIONS NCAUTION e Do not bundle the control and communication cables with main circuit power or other wiring Run the above cables separately from such wiring and keep them a minimum of 100mm 3 94in apart Not doing so noise can cause a malfunction User s Manual Manual Number JY997D24601D This manual describes the part names dimensions mounting and specifications of the product Before use read this manual and manuals of relevant products fully to acquire proficiency in handling and operating the product Make sure to learn all the product information safety information and precautions And store this manual in a safe place so that you can take it out and read it whenever necessary Always forward it to the end user Registration The company name and the product name to be described in this manual are the registered trademarks or trademarks of each company Effective Apr 2013 Specifications are subject to change without notice 2008 Mit
22. usly Connector model name JES 9P 2A3A JST aa depth 25 0 98 25 0 98 3 Specifications 6 0 23 General Specifications Applicable GOTs Model name Abbreviations GT1455HS QTBDE GT1450HS QMBDE 1 GT14 Handy GOT GT11 Handy GOT Item Specifications Operating ambient temperature 0 to 55 C GOT 1000 10 to 90 RH non condensing GT1155HS QSBD GT1150HS QLBD The wet bulb temperature is 39 C or less In conforms to JIS B3502 and IEC61131 2 5 to 9Hz Half amplitude 3 5 mm 9 to 150Hz Acceleration 4 9m s2 10 times sweeping in each of X Y and Z directions Operating ambient humidity Vibration resistance AN haim Must be free of lamp black corrosive gas Panel Lg 3 i flammable gas or excessive amount of K Operating atmosphere electroconductive dust particles and must be no face YU 100 3 93 en ee direct sunlight Same as for saving Je _ l External Dimensions 37 5 1 47 5 Cautions for use For the emergency stop SW the b contact type is used When the Handy GOT is installed and removed with the connector the switch changes ON to OFF when ri A EQ_3 1 Terminal name Eog removed which is the same as the state where the emergency switch is pressed ge Design such as configuring a parallel circuit outside must be taken into consideration Jra to avoid e
23. x from the back side of the panel face and fix it with four M3 screws prepared by user In the Connector Conversion Box thread of M3 6mm 0 23 in depth is cut in each mounting hole Prepare four M3 mounting screws separately while con sidering the thickness of the panel face Connector Thread depth Conversion 6 0 23 Box 18 0 7 28 1 1 _18 0 7 Drill 4 3 5 _ lt 25 0 98 l s 3 Se I 2 a N 5 r Rs i E i r A roasts Panel PTOA Panel cut area r face U Unit mm inch 100 3 93 M3 screw x 4 pieces 1 prepared by user Unit mm inch 1 Attaching a mounting bracket 2 Attach the provided mounting bracket to the Connector Conversion Box Mounting on the panel face Mount the Connector Conversion Box on the panel face Drill screw holes on the panel face as follows Connector Conversion Box Drill 3 4 5 Y Mounting bracket accessory gt i S B S SIS M4 screw and nut S x 3 sets 4 prepared by user se oP Mounting 10 0 39 Mounting screw accessory ee Bracket 20 0 78 zz 3 screw x 3 pieces Unit mm inch 4 3 Installation requirements for the rear face of enclosure Make sure that interfering objects are not located within 100mm 3 93 from the rear face so that the connector of a PLC cable is not hindered To wire the terminal block keep
Download Pdf Manuals
Related Search