Fire Safety & Security Products
Contents
1. 140 F Humidity 10 90 RH non condensing Standards and Guidelines European Directives Directive of Electromagnetic Compatibility Emitted interference EN 61000 6 3 2001 EN 55022 A1 A2 KI B 2003 Interference resistance EN 50130 4 A2 2003 C Tick Standard for Australia and New Zealand equivalent to EN 55022 of the European Directive UL Directives UL 294 Access control units Details can be found under http database ul com cqi bin XY V template LISEXT 1FRAME gfilenbr html with UL File Number BP9490 Siemens Building Technologies Fire Safety amp Security Products 05 2008 Technical specifications 3 1 Dimensions 210 mm 190 mm Locat savour ponsi Fons ek je ey jo Ok e or er er ER oo 4 Ox aa gt MONO eb er STO Di ST eR fef E zZ E E HH BA HH BA HH HH BA EH N MN TETE outs OUT ou Ta ours out OUT 1 FUN asus RELAY OUTPUTS 1 TOS DC POWER IN ou Te ours ox 000090 0000006 009090 XXXXX XX o Fig 1 Dimensions including base plate e Width 250 mm 9 84 e Height 210 mm 8 27 e Depht 40 mm 1 57 Siemens Building Technologies Fire Safety amp Security Products 05 2008 Ordering data 4 Ordering data Type Part no Designation Weight AFO5200 S24246 A2600 A1 Eight Input Output Module 0 7 kg 5 Scope of delivery 1 x AFO5200 mounted on base plate 1 x accessory bag resistor2. host software and download of the firmware instruction set Alternatively the firmware and configuration may be carried out using the FLN Field Service Tool Siemens Building Technologies Fire Safety amp Security Products 05 2008 Connections and LEDs 7 Connections and LEDs 7 1 Connections i It is recommended that you wear a grounding strap while carrying out this procedure 1 Connect all input devices to the ports INPUT1 to 8 supervised For more information see Section 7 3 Wiring of monitored input i Listed end of line resistors must be connected to the wiring for each input device if they are to be Please note this applies to all inputs The total cable run resistance must not exceed 100 Ohms 2 Connect all output devices to the ports RELAY OUTPUTI to 8 Access doors can only be connected to relay outputs that are controlled by readers 3 Connect the wiring from the Fire and Emergency Override system to the FOR IN port Ensure the correct FOR link settings are applied 4 Connect the next device in the Fire Override sequence to the FOR OUT port 5 Connect the FLN wires from the ACC to the FLN RS485 port 6 Connect the active ve and neutral ve wires from the power supply unit PSU to the DC POWER IN port Ensure the polarity of the connection is ma de correctly 7 Check all jumpers For more information see Section 7 5 Links and jumpers 8 Check all connections thorough
3. R input will cause the appropriate output relays to pick up or drop out depending on where the o o links LK10 LK17 are placed FOR disabled LK6 LK7 LK6 LK7 2 The input will have no effect on the relays FOR disabled FOR enabled LK9 RESET Restart Reset the AFO5200 retaining the unit s firmware Interrupt the power supply to the unit for 1 sec or Close link 9 wait for the activity LED to switch off then remove LK9 LINKS 10 17 FOR OUTPUT CONTROL These links control the Fire Over ride activation for each ee FOR EN individual relay output 1 8 e el 00 ron nis Depending on where you place the link the relay output behaviour will be modified by the FOR input or FOR will be disabled for that relay LK10 LK11 Output OUT8 LK10 FOR disabled Output OUT7 LK11 FOR enabled LK18 EOL TERMINATION FLN System Bus This link allows the RS485 bus communication channel to be terminated in lengthy comms lines more than 100 m at 115 kb s Note Only units that are located at the ends of bus lines should have Link 26 set to on LK 19 LK 20 BIAS Jumper placed across LK19 and LK20 These links enable the RS 485 bus biasing resistors The gt RS485 FLN biasing resistors enabled resistors create a voltage divider to force the voltage to be LK19 LK20 less than the threshold of the receiver This prevents invalid data bits that are picked up from the noise on the cable from being transmitted 13 Siemens Building Techn
4. SIEMENS SiPass integrated AFO5200 Installation Manual Fire Safety amp Security Products Siemens Building Technologies Lieferm glichkeiten und technische nderungen vorbehalten Data and design subject to change without notice Supply subject to availability 2008 Copyright by Siemens Building Technologies Wir behalten uns alle Rechte an diesem Dokument und an dem in ihm dargestellten Gegenstand vor Der Empf nger erkennt diese Rechte an und wird dieses Dokument nicht ohne unsere vorg ngige schriftliche Erm chtigung ganz oder teilweise Dritten zug nglich machen oder auBerhalb des Zweckes verwenden zu dem es ihm bergeben worden ist We reserve all rights in this document and in the subject thereof By acceptance of the document the recipient acknowledges these rights and undertakes not to publish the document nor the subject thereof in full or in part nor to make them available to any third party without our prior express written authorization nor to use it for any purpose other than for which it was delivered to him Contents 1 Product description 5 2 SEU EE 5 3 Technical specifications eere 6 3 1 DIMENSIONS ca e a Ba Ann um eM Beeren 7 4 Ordering d l aa is 8 5 Scope of delivery AA 8 6 Installation 2 noii RE 9 7 Connections and LEDs essen enne nennen 10 7 1 Conneccion art nn eM EG te EM dec I dote ride 10 7 2 Portlocations corr
5. e Safety amp Security Products 05 2008 18 Siemens Building Technologies Fire Safety amp Security Products 05 2008 Issued by Siemens Building Technologies Fire amp Security Products GmbH amp Co oHG D 76181 Karlsruhe www sbt siemens com 2008 Copyright by Siemens Building Technologies Data and design subject to change without notice Supply subject to availability Printed in the Federal Republic of Germany on environment friendly chlorine free paper Document no A24205 A335 B263 Edition 05 2008
6. e aret ENNA 10 7 3 Wiring of monitored input ssssssseeseeneenenmnenennnnnnn 11 7 4 FOR inputs Lm dre e d etum pe att 11 7 5 Links and jumpers eee a a Aa e a e eia 13 7 6 A aste diit ag de NLA a n ad ue Ped eel a id 14 8 Recommended cable specifications sses 15 9 Programming and firmware download 15 10 Disposal 5 a AA Iu 16 10 1 Record of proper waste management 16 3 Siemens Building Technologies Fire Safety amp Security Products 05 2008 4 Siemens Building Technologies Fire Safety amp Security Products 05 2008 Product description 1 Product description 2 Safety The AFO5200 is an input output module that provides an interface between input and output devices and an Advanced Central Controller ACC in a Siemens ac cess control and security environment We decline any liability for material damage or personal injury caused by im PLEASE NOTE proper use or non observance of these safety instructions In such case any guarantee expires Connection commissioning and maintenance must only be carried out by suita bly qualified personnel Correct and safe operation of this device depends on proper transport storage installation and connection as well as careful operation and maintenance PLEASE NOTE Work on electrical systems should only be performed by trained personn
7. el DANGER under the supervision of a certified electrician in accordance with the appropri ate regulations Siemens Building Technologies Fire Safety amp Security Products 05 2008 Technical specifications 3 Technical specifications 6 Electrical Power input 12 V DC 15 to 10 or 24 V DC 15 to 10 Consumption max 2 A 12 V DC max 1 5 A 24 V DC Fully loaded All Relays are driven and the Aux Power Output supplies its max current of 1 5 A Communications FLN RS 485 two wire half duplex Inputs internally supplied 8 x Auxiliary unsupervised or supervised Outputs 8 x Relay 2 A 30 V DC Fire Override FOR input 1 x Fire Override input Normal or Enhanced Modes e Normal mode requires an input voltage of 12 V DC e Enhanced mode requires the connection of 22 kOhm resistor circuits Cable must be shielded and total cable run resistance must not exceed 100 Ohms Fire Override FOR output 1 x Relay 2 A 30 V DC Local input 1 x passive device connection Local output 1 x open collector 100 mA 9 7 12 V DC Aux Power output 1 5 A Q9 9 7 12 V DC Dimensions with base plate W x H x D 250 x 210 x 40 mm 9 84 x 8 27 x 1 57 without base plate W x H x D 216 x 190 x 28 mm 8 50 x 7 48 x 1 10 Environmental Operating Temp 0 50 C 32 122 F Storage Temp 0 60 C 32
8. ly including the polarity of each connection Once you have verified all connections power can be applied to the AFO5200 7 2 Port locations Port name Description DC POWER IN DC power input 12 V DC or 24 V DC FLN RS485 RS 485 bus for AC5100 FLN bus RELAY OUTPUTS 1 8 Auxiliary relay outputs INPUTS 1 8 Inputs FOR IN FOR input e g fire alarm button FOR OUT FOR output LOCAL IN Tamper input for local tamper detection LOCAL OUT Alarm output e g siren strobe light 12V OUT Auxiliary 12 V DC power output FOR Fire Override 10 Siemens Building Technologies Fire Safety amp Security Products 05 2008 7 3 Wiring of monitored input Connections and LEDs AA O N AFO5200 Connect the shielding to the housing earth Insulate the shielding at the input e g door contact do not connect it DC Door contacts R Terminating resistors 22 kOhm each Fig 2 Wiring of monitored input 7 4 FOR inputs AFO5200 External device Port Remark FOR input normal mode Fire alarm system UB AFO5200 Fire System Fire alarm system output Fire alarm system OK gt 12V In case of fire alarm or malfunc tion 20V FOR input normal mode Fire alarm system relay contact AFO5200 Fire System Power Supply Fire alarm system output Fire alarm system OK 2 contact between NO and COM closed In case of fire alarm or malf
9. nium foil Polyester Tinned Polyethylene tape no braid Copper Power 12 24 Foam V DC Polyethylene Unshielded 9 Programming and firmware download The AFO5200 is programmed using SiPass software via the AC5100 or using the FLN Configurator application Please refer to the appropriate User s Manual for more information 15 Siemens Building Technologies Fire Safety amp Security Products 05 2008 Disposal 10 Disposal AH All electrical and electronic products should be disposed of separately from the municipal waste stream via designated collection facilities appointed by the gov ernment or the local authorities This crossed out wheeled bin symbol on the product means the product is cov ered by the European Directive 2002 96 EC The correct disposal and separate collection of your old appliance will help pre vent potential negative consequences for the environment and human health It is a precondition for reuse and recycling of used electrical and electronic e quipment For more detailed information about disposal of your old appliance please contact your city office waste disposal service or the shop where you purchased the pro duct 10 1 Record of proper waste management 16 A record of proper waste management is not required Siemens Building Technologies Fire Safety amp Security Products 05 2008 17 Siemens Building Technologies Fir
10. ologies Fire Safety amp Security Products 05 2008 Connections and LEDs 7 6 LEDs 14 LED Description PWR LED active power is applied to the PCB COM IN1 8 FOR IN ACTIVITY LED 1 LED blinking quickly Firmware needs to be downloaded 2 LED blinking slowly approx once per sec Firmware has been downloaded The LED flashes when the AFO5200 is sending data to the AC5100 LED active Relay active green LED active relay active Status of inputs LED red Alarm Fire Override at FOR input LED green Normal LED orange Tampering LED off only FOR IN FOR disabled Siemens Building Technologies Fire Safety amp Security Products 05 2008 Recommended cable specifications 8 Recommended cable specifications The table provides a guideline for selecting an appropriate cable type only Other cable types are also compatible with the system and can be used to achieve the same results Communica Recommended Cable Specifications tion Type J Y St Y Wire Type Insulation Shield Jacket Diameter mm RS 485 Tinned Foam Aluminium foil Polyester 28 TERES OG Copper Polyethylene tape braided shield PNG Foam Aluminium foil Polyester Polyethylene tape no braid Foam Aluminium foil Polyester Polyethylene tape no braid AJA HO m JO IN FH fo N 4 6 8 4 6 8 4 6 8 8 Bare Cop per Tinned Copper Bare Cop per Polyethylene Unshielded Alumi
11. s for monitored inputs 1 x installation manual English 1xinstallation manual German 8 Siemens Building Technologies Fire Safety amp Security Products 05 2008 6 Installation Installation Required tools amp material Medium duty drill and associated drill bits 4 mounting screws or standoffs approx 4 mm Flat blade terminal screwdriver Wire cutters Cable strippers Expected installation time 30 minutes Mounting instructions 1 Remove the AFO5200 from its carton and discard the packaging material 2 Place the AFO5200 base plate against the surface to which it is to be affixed and mark the location of the mounting holes We recommend to mount the AFO5200 within a cabinet Align the AFO5200 base plate with the holes located on the cabinet backplane and proceed to step 3 It is recommended that you affix the AFO5200 at all four of the mounting loca tions provided Warning Do not apply power to the AFO5200 or associated components at this stage 3 Select the appropriate drill bit according to the mounting surface hole size and drill the holes in the locations marked if required 4 Fasten the AFO5200 base plate to the surface using the correct type of screws or standoffs for the surface 5 Connect the AFO5200 For more information see Section 7 1 Connections 6 Apply power to the AFO5200 and test its operation This step may require installation and programming of the access control
12. unc tion 2 contact between NO and COM open FOR input enhanced mode Fire alarm system relay contact AFO5200 FOR IN O Fire alarm system output Fire alarm system OK 2 contact between NO and COM closed In case of fire alarm or malfunc tion 2 contact between NO and COM open FOR Fire Override 11 Siemens Building Technologies Fire Safety amp Security Products 05 2008 Connections and LEDs The following diagram provides an example for wiring a door lock in a fail safe mode for fire override operation DOOR LOCK FIRE OUT NO COM NC 12 Siemens Building Technologies Fire Safety amp Security Products 05 2008 Connections and LEDs 7 5 Links and jumpers Jumper LK1 LK2 Description Value FOR MODE LK1 LK2 Configuration of the Fire Override mode Enhanced FOR mode monitored Normal FOR mode floating Jumpers placed over both links gt Input set to Normal FOR mode Jumpers not placed gt Input set to Enhanced FOR mode LK3 LK4 LK8 These links are general purpose links that have been included for future enhancement LK5 GP1 RESET MODE Reset the firmware Close LK5 Close link 9 wait for the activity LED to switch off then remove LK9 Remove LK5 before loading the new firmware LK6 LK7 FOR AKTIVATION FOR ENABLE FOR ENABLE FOR enabled e e 2 Activation of the FO
Download Pdf Manuals
Related Search