DRS-6/1 Doppler Radar Sensor
Contents
1. ee MULTIDATH DRS 6 1 Doppler Radar Sensor B S Software und Messtechnik GmbH Lochhamer Schlag 17 D 82166 Graefelfing Germany October 1999 User s Manual Doppler Radar Sensor Type DRS 6 1 Users Manual October 1999 DRS 6 SENSOR for speed measurements 1 DRS 6 Functional Description Doppler Radar Sensors provide slip and contact free measurements of speed and distance This sensor measures the vehicle moving speed using the Doppler effect principle That is it measures the frequency shift between transmitted and reflected waves and this shift is proportional to the vehicle speed A sophisticated electronic signal conditioning is required to practically realize this simple principle The microwaves are transmitted and then received after reflection by the same antenna The Doppler frequency is obtained by mixing the outgoing and incoming signals The beam is not focused and therefore the returned beam is reflected from an area and not from a point The result is a spectrum shift rather than a single frequency shift The characteristic frequency is then amplified and filtered This method ensures that the result is as far as possible independent of the type of reflecting surface and unavoidable vibration 24 GHz microwaves are used The Doppler frequency depends on the alignment of the antenna To reduce the errors caused by vehicle pitch two transmitter receiver antennas are used in the DRS 6 They are mounted at 110 deg2. 1999 4 Performing a Measurement Once the sensor is mounted correctly and powered on it is ready to measure without further calibration The digital speed output shows TTL pulses with a frequency of 70 Hz per km h 112 Hz per mph On the analog output the voltage is proportional to the speed 10V 300 km h 185 mph or 10V 200 km h 125 mph The signals can be measured with standard pulse counters or voltmeters or PCs with a serial interface Ask for ME3 software The DRS display option uses the frequency output to calculate the distance and speed and displays these in the required units on a LCD screen 5 DRS 6 Serial Interface The serial interface of the DRS 6 provides the following features e Asynchronous transmitting interface transmit only e Transmission corresponds to RS232C specification with TxD and GND e The Baud rate is 19200 Bit s 8 data bits are transmitted no parity bit 1 stop bit e Data block transmission repetition rate is 10 ms Pinning of the 9pin Sub D connector pa nm 4 ns 7 n 2 TxD 5 GND 8 ne 2 3 m 6 ne 9 nc Doppler Radar Sensor Type DRS 6 1 Users Manual October 1999 Transmission protocol Fe ee 1 INFORMATION FOOTER Fe er of segment bytes in function ae 1 word 2 word ae checksum substructure one aia code low byte of the sum display of the low byte 1 nn byte low byte 2 a byte low byte 6 an byte of bytes in 15 bytes block one blo
3. Type DRS 6 1 Users Manual October 1999 6 Calibration The sensor is designed to operate within the accuracy limits stated in chapter 2 of this manual without any further calibration The instruments attached however must be calibrated in order to achieve the best overall performance The VS display unit offers a setup routine during which you tell it the real distance between pulses Please refer to the VS display manual to set the value Data acquisition systems also offer calibration entries to convert electrical input signals to physical units If you use the ME3 DRS 6 software or any other means reading the serial output please note The values delivered at the serial output depend on an assumed calibration value of 4 000 mm pulse at the pulse output The actual values of the units might differ slightly i e the statement in chapter 2 may say Distance resolution 3 9738 mm per pulse 0 15 inch per pulse Therefore to calibrate the speed value in ME3 DRS 6 you will use the User Unit Menu As first value enter 0 km h 0 lt digits gt As second value enter 200 or 300 km h 4000 3973 8 32767 32983 lt digits gt In this example the calibration values are just multiplied by 1000 to make calculations easier for computers by avoiding to many decimals The distance counters must be calibrated accordingly 0 m 0 lt digits gt 1000m 4000 3973 8 65536 65968 lt digits gt As the highest value to be o
4. apart The base plate should be vertical and the top edge should be horizontal parallel to the reflecting surface ground Thus the sensor is fastened with the transmitting receiving faces looking evenly at 35 degrees into the forward and backward directions The base plate is to be parallel to the moving direction There should be a clear path between the antennas and the reflecting surface The sensor should be fastened to a low vibration area of the vehicle The spray range of the wheels should be avoided The following mounting methods have shown good results e On the side of body panels between the wheels with vacuum suction cups It might be helpful sometimes to tilt the sensor slightly so that the beams do not get to the ground vertically but are reflected away from the vehicle e On the back or front tow loop avoiding the wheel spray range e On the ball hitch of the tow bar e Centrally underneath the vehicle when the minimum distance between surface and sensor can be maintained Various mounting materials are available as accessories The signal is output on a 10 pin connector A ready to use cable is provided The 12V vehicle power can be used to supply the sensor If you use a different cable make sure that frequency and analog outputs are shielded shield ground The sensor base plate is not connected to the measurement ground to prevent possible ground loops Doppler Radar Sensor Type DRS 6 1 Users Manual October
5. ck 2 comple ment data format of startbit LSB om MSB stopbit the transmitted 0 BitO Bitl oti Bit6 Bit7 1 bytes Transmitted words Note v max 300 km h or 200 km h according to your model word 1 Filtered speed v as supplied to the analog output Measurement range v max lt v lt v max Output range 0 km h lt v lt v max Output format Binary 15 bits with O km h 0 v max decimal 32767 hex 7FFF word 2 Unfiltered speed v as supplied to the pulse output Measurement range v max lt v lt v max Output range 0 km h lt v lt v max Output format Binary 15 bits with 0 km h 0 v max decimal 32767 hex 7FFF word 3 Acceleration proportional output not calibrated word 4 Distance counter 1 in meters s_m Output range 0 m lt s_m lt 1000 m Output format Binary 16 bits with 0 m 0 1000m decimal 65536 highest value that can be transmitted is one LSB less corresponding to decimal 65535 hex FFFF word 5 Distance counter 2 in km s_km Output range 0 m lt s_km lt 1000 km Output format Binary 16 bits with Om 0 1000km decimal 65536 highest value that can be transmitted is one LSB less decimal 65535 hex FFFF word 6 Sensor status positive blackout no signal while measuring 0 acquisition searching for signal spectrum negative sensor is working normal Note LSB least significant bit the smallest amount that can be expressed in the given data format Doppler Radar Sensor
6. heet lt 1 appr 4mm Pulse see calibration sheet lt 0 2 over 200m 600ft v gt 7 5km h Smph lt 0 4 at 5 degrees deviation appr 70 Hz per km h see calibration sheet 1 1 square wave TTL at v gt 0 2 km h 0 12 mph 0 to 10V 12 bit resolution sensitivity according to calibration sheet RS 232C 19 2 kBaud lt 0 005 C 30 to 70 C 22F to 158F 10 35V lt 5 W integrated DC DC converter 10 pin water tight KPSE connector A ne F RS 232C TxD B ground G pulse out C analog ground H DCin D RS 232C ground I analog out E ne K digital ground 200 800mm 8 32 above the reflecting surface ground 800 1200mm for railway applications base plate at right angle to direction of movement top side of base plate parallel to reflecting surface app 150 x 80 x 73 mm 800 g 5 9 x 3 2 x 2 9 1 8 Ib 24 125 or 24 200 GHz see label At 5mW the radar radiation is of very low intensity and does neither endanger people nor animals Doppler Radar Sensor Type DRS 6 1 Users Manual October 1999 3 Sensor Installation The sensor should always be installed between 200 800mm 8 32 800 1200mm for railway applications above the reflecting surface This guarantees the rated measurement accuracy and ensures that the sensor can function independently of reflecting surface conditions The sensor can be fastened at the base plate using M6 bolts The base plate has 3 fastening holes 57 mm
7. rees to each other 35 to the horizontal one pointing to the direction of movement one in the opposite direction Signal processors are used to convert the results to a square wave with a frequency proportional to the velocity as well as a voltage proportional to the velocity The sensor housing is water tight and protected against condensation caused by temperature changes To prevent ground loops the base plate is isolated from the sensor ground Type overview Product code DRS 6 1 xy X values a for 24 125 GHz microwave frequency b for 24 200 GHz Japan version y values a for 1OV 200 km h 125 mph 69 4 Hz km h 4 mm pulse b for 10V 300 km h 187 mph 69 4 Hz km h 4 mm pulse c for 10V 300 km h 187 mph 10 Hz km h 4 mm pulse d for 1OV 200 km h 125 mph 27 77 Hz km h 10mm pulse e for 5V 300 km h 187 mph 69 4 Hz km h 4 mm pulse f for 10V 200 km h 125 mph 109 36 Hz km h 120 pulses ft 394 pulses m g for 5V 250 km h 156 mph 69 4 Hz km h 4mm pulse Doppler Radar Sensor Type DRS 6 1 Users Manual 2 DRS 6 Specifications Measurement range Speed accuracy Distance resolution Distance accuracy Error due to tilt angle Frequency output DC output Serial interface Temperature error Operating temperature Power supply Connector Mounting position at vehicle Dimensions mass Microwave frequency Note October 1999 200 km h 125 mph or 300 km h 185 mph see calibration s
8. t the interference by one or more of the following ways e Re orientate or relocate the receiving antenna e Increase the separation between equipment and receiver e Connect the equipment to an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help e The use of a non shielded interface cable with the referenced device is prohibited 2170 EEN 350 max 80 CQO Sa 3 X XT Sy off DOK SSO RY SR Te DRS 6 Beam directions and sizes
9. utput with 16 bits is 65535 the maximum distance measured with this output and this sensor can be 1000 65535 65968 993 44 m Doppler Radar Sensor Type DRS 6 1 Users Manual October 1999 7 DRS 6 Accessories The following accessories are available with the Doppler radar sensor DRS 6 e Water tight KPSE connector for user provided cable e 5 or 10m second DRS 6 cable with KPSE connector and connectors for power the analog and frequency outputs and RS232C output e Speed and distance display unit with large alphanumeric display ME3 program for real time display and analysis 150 le 73 gt in mm Doppler Radar Sensor Type DRS 6 1 Users Manual October 1999 8 Interference Considerations Note This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correc
Download Pdf Manuals
Related Search