Manuals - Microh
Contents
1. 3 5m 11 5 5 3m 17 4 7m 23 ATTACHMENT AND BODY SIZE USER MANUAL BRACKET LAMP fitted into projector WARRANTY CARD DMX CABLE SAFETY CORD Attachmentcontents Fig 1 Body Size Fig 2 INSTALLATION AND CONNECTING Installing the projector Fig 3 The projector can be installed on the floor resting on special rubber feet on a truss or on the ceiling or wall WARNING with the exception of when the projector is positioned on the floor the safety cable must be fitted This must be securely fixed to the support structure of the projector and then connected to the fixing point at the centre of the base Connecting to the mains suppply Fig 4 SIGNAL id SCREEN 3 p DMX512 5 PIN I SCREEN gt SIGNAL SIGNAL Connecting to the control signal line DMX Fig 5 O Please use the round 3 or 5 pin XLR plugs amp sockets offered by menu facture to connectthe first projector s output to the second projector input and connect the second projector s output to the third projector s input And the same way for the rest eventually connect the last projector s output all the projectors are together The p2. GOBO CHANGE channel 4 242 255 227 241 212 226 198 211 183 197 168 182 154 167 139 153 124 138 110 123 95 109 80 94 72 79 67 71 61 66 56 60 50 55 45 49 39 44 34 38 28 33 23 27 17 22 12 16 6 11 EFFECT GOBO12 SWING SLOW FAST GOBO11 SWING SLOW FAST GOBO10 SWING SLOW FAST GOBO9 SWING SLOW FAST GOBO8 SWING SLOW FAST GOBO7 SWING SLOW FAST GOBO6 SWING SLOW FAST GOBOS5 SWING SLOW FAST GOBO4 SWING SLOW FAST GOBO3 SWING SLOW FAST GOBO2 SWING SLOW FAST GOBO1 SWING SLOW FAST WHITE GOBO 12 GOBO 11 GOBO 10 GOBO 9 GOBO 8 GOBO 7 GOBO 6 GOBO 5 GOBO 4 GOBO 3 GOBO 2 GOBO 1 GOBO ROTATION channel 5 BIT EFFECT 240 255 224 239 208 223 192 207 128 191 64 127 0 63 SWING FROM SLOW TO FAST 360 SWING FROM SLOW TO FAST 180 SWING FROM SLOW TO FAST 120 SWING FROM SLOW TO FAST 60 FORWARDS ROTATION FROM SLOW TO FAST BACKWARDS ROTATION FROM FAST TO SLOW ANGLE ADJUSTMENT ORIENTATION PRISM channel 6 EFFECT 130 255 PRISM INSERTED 0 129 PRISM EXCLUDED PRISM ROTATION channel 7 9 da e C9 ZOOM channel 9 BIT EFFECT 255 Zoom from Max to Min beam angle FOCUS channel 10 EFFECT NEAR DISTANT BIT EFFECT 240 255 224 239 208 223 192 207 129 191 127 128 64 126 0 63 SWING FROM SLOW TO FAS
3. the projectors from indirect contact and or shorting to earth by using appropriately sized residual current devices Connection to mains supply Connection to the electricity mains must be carried out by a qualified electrical installer Check that the mains frequency and voltage correspond to those for which the projector is designed as given on the electrical data label This label also gives the input power to which you need to refer to evaluate the maximum number of fittings to connect to the electricity line in order to avoid overloading Don t use the power cable when the insulation is damaged It must be the manufacturer or distributor or the professional person to change the damaged power cable in order to avoid any dangerous Temperature of the external surface The maximum temperature that can be reached on the external surface of the fitting in a thermally steady state is 100 C Maintenance Before starting any maintenance work or cleaning the projector cut off power from the mains supply After switching off do not remove any parts of the fitting to avoid getting burnt for at least 30 minutes After this time the likelihood of the lamp exploding is virtually nill The fitting is designed to hold in any splinters produced by a lamp exploding The lenses must be mounted and if visibly Damaged they have to be replaced with genuine spares Lamp The fitting mounts a high pressure lamp that needs an external igniter
4. MICROH Ultra Trinity330 PROFESSIONAL SHOW LIGHTING Contents Te Sat ty informati ohuuuu kusa 2 2 Technical information 3 3 Attachment and body s126 uiiii ia 5 4 Installatlon and connecting seriali 6 5 Controllpanel d 7 6 Menu setting u 2 un dier axi A 8 7 Channel 10 8 CIrcuit connecting dlagram 1 ioter erroe rine hio ene exe koe anh exu Resa 15 9 Cleaning and malntenanceS ocioso 16 TO TroUDESHOOt NO iccoiconnncan escarnio ninia 16 11 Duty exonerative and copyright protection ii 17 Congratulations on choosing our company product We thank you for your custom Please note that this product as all the others in the rich my company range has been designed and made with total quality to ensure excellent performance and best meet your expectations and requirements Carefully read this user manual in its entirety and keep it safe for future reference It is essential to know the information and comply with the instructions given in this manual to ensure the fitting is installed used and serviced correctly and safely company disclaims all liability for damage to the fitting orto other property or persons deriving from installation use and maintenance that have not been carried out in conformity with this user m
5. P REDUCING POWER INSTANT ACTION 0 31 UNUSED RANGE Circuit connecting diagram LAMP gigs Bee saadi Power input AC90 240V 50 60Hz MCU1 12 MCU2 I 36 312 oo Fan XA J13 7 J4 Ss o J8 J9 J19 J26 J27 J21 J22 123 311 6 6 5 PRISM GOBOR GOBO STROBE COLOR STROBE FOCUS ZOOM PRISMR FROST Powerinput Electronic ballast Ovraxis motor T Power input output MCUProgrammer port J5 Lithium battery port 33 Edo Connect display line i al isinan Deseo X Y Drive board CLEANING AND MAINTENANCES order to ensure the projector could work normally It should be kept clean always It is recommended that the fans and ventilation in let should be cleaned every 15 days The lens and dichroic colour filters should also be reg ularly cleaned to maintain an optimum light output Do not use any type of solvent on dichroic colour filters It will damage the projector OSuggestion The continue usage of the light don t exceed 4 hours Or it will shorter the usage of the lamp Please use the alternative operation to solve this problems G Please disconnect the power supply when begin to maintenaceor takedown the light Please
6. T 360 SWING FROM SLOW TO FAST 180 SWING FROM SLOW TO FAST 120 SWING FROM SLOW TO FAST 60 BACKWARDS ROTATION FROM SLOW TO FAST STOP FORWARDS ROTATION FROM FAST TO SLOW ROTATION 0 360 ORIENTATION FROST channel 8 EFFECT PAN channel 11 BIT EFFECT 255 540 PAN FINE channel 12 BIT 255 EFFECT 239 TILT FINE channel 14 BIT EFFECT 255 FUNCTION channel 15 BIT EFFECT 212 255 206 211 199 205 192 198 185 191 178 184 171 177 164 170 157 163 146 156 135 145 124 134 113 123 102 112 91 101 80 90 69 79 58 68 47 57 36 46 25 35 14 24 0 13 UNUSED RANGE COMPLETE RESET 5S ALL MOTOR OF HEAD RESET 5S FROST MOTOR RESET 5S FOCUS AND ZOOM MOTOR RESET 5S PRISM MOTOR RESET 5S COLOUR MOTOR RESET 5S GOGO MOTOR RESET 5S STROBE MOTOR RESET 5S UNUSED RANGE LCD POSITIVE 5S LCD REVERSE 5S LCD TURN OFF 5S LCD TURN ON 5S UNUSED RANGE GOBO COLOUR PRISM FROST HEAD FUNCTION CHANGEING BLACKOUT XY GOBO COLOUR PRISM FROST CHANGING BLACKOUT FROST SELECTING BLACKOUT PRISM SELECTING BLACKOUT COLOUR CHANGING BLACKOUT GOGO CHANGING BLACKOUT XY MOVING BLACKOUT UNUSED RANGE LAMP CONTROL channel 16 BIT EFFECT 224 255 LAMP ON 5S 192 223 UNUSED RANGE 160 191 LAMP OFF 5S 64 159 UNUSED RANGE 32 63 LAM
7. This igniter is fitted onto the apparatus Carefully read the operating instructions provided by the lamp manufacturer Immediately replace the lamp if damaged or deformed by heat Battery This product contains a rechargeable lead acid battery To preserve the environment please dispose the battery at the end of its life according to the regulation in force The products referred to in this manual conform to the European Community Directives to which they are subject Low Voltage 2006 95 CE Electromagnetic Compatibility 2004 108 CE 2 TECHNICAL INFORMATION O Power supplies available AC90 240V 50 60Hz G Power 440W 220V 50Hz G Lamp Brand SIRIUS HRI 330W OSRAM Power 330W Colour temperature 7500K Average life 1500h Motors 12PCS mute sound motor 2PCS three phase motor 16bit driver O Channels Standard 16 control channels Beam angle Parallel beam angel 0 20 O inputs DMX 512 WIRELESS DMX 512 Apolegamic Strobe Double lens strobe 0 5 14 times second Dimmer 0 100 linear adjustment Prism One bilateral rotation prism Lens High presision optical lens Wash effect Adjustable wash effects angle Travel PAN 540 TILT 239 Maximum speeds PAN 2 6s 540 TILT 1 24s 239 Resolution PAN 2 11 PAN FINE 0 008 TILT 0 94 TILT FINE 0 004 IP set Automatic charging battery IP could be set without electr
8. anual which must always accompany the fitting My company reserves the right to modify the characteristics stated in this user manual at any time and without prior notice t 100 C SAFETY INFORMATION Installation Make sure all parts for fixing the projector are in a good state of repair Make sure the point of anchorage is stable before positioning the projector The safety chain must be properly hooked onto the fitting and secured to the framework so that if the primary support system fails the fitting falls as little as possible If the safety chain gets used it needs to be replaced with a genuine spare MINIMUM DISTANCE OF ILLUM INATED OBJECTS The projector needs to be positioned so that the objects hit by the beam of light are at least 12 metres from the lens of the projector Minimum distance from flammable materials The projector must be positloned so that any flammable materials are at least 0 2 metres from every point on the surface of the fitting Mounting surfaces It is permissible to mount the fitting on normally flammable surfaces Maximum ambient temperature Do not operate the fixture if the ambient temperature Ta exceeds 38 C Protection against electrical shock Connection must be made to a power supply system fitted with efficient earthing Class appliance according to standard EN 60598 1 It is moreover recommended to protect the supply lines of
9. e life OPlease check if the power supply is enough the connection of the power supply or the circuit are good OPlease check if the switch of the sup temperature is good Though the light is lighting but it couldn t accept the control order Please check the start code address and the function option are correct OPlease check whether the communicate control cable is ongood connection or the cable is too long or interrupt Please check the control system is not valid check the singal amplifier of chain connected is valid OPlease check whether the communicate cable is too long or the other equipment is mutually conjugate OPlease arrange the wire well Shorter the signal cable put the high voltage cable and low voltage cable separ ately OAdd the signal amplify isolator Signal cable is used the excellent screening doublet Resistance 75 9 OThe end ofthe light end and the end resistance When the lamp don t cool down enough but do the incorrect operation will let the trigger up to super high voltage leak It will damage the electric circuit and communicate IC or CPU Under this condition please change the PCB board Mthe light can t move OPlease check if the power supply is suitable for the light voltage data OPlease check the fuse of input voltage is defective OPlease check the light if they are deformating inside parts is broken become wet etc will lead the loose contact OPlease check if the inside lead wire and the connector
10. ht Open return ESC Auto return ESC 1 Close 15S System Version PT Color MCU1 V x Strobe MCU2 V F7 5 Dimmer MCUS V Gobo Fixture ITotal e hrs Gobo Rota Hours Cur Prism Prism Rot Total hrs Frost Cur hrs Zoom Time Clear Clear PWRON Time Focus Clear LAMP Time Pan anrine Fan1 RPM Monitor Fan2 RPM a TiltFine Fan3 RPM Function Lu Lamp Manual Control Lamp return ESC SystemReset Pan Tilt Reset Effect Reset return esc Factory Password Input default 1111 Password Input 2222 Color Adjust return ESC 1 When the dmx signal is fine it shows DMX Input OK Restore the factory parameters Gobo Adjust Value 000 255 Shutter Adjust Value 000 255 Focus Adjust Value 000 255 Zoom Adjust Value 000 255 Pan Adjust Value 000 255 Tilt Adjust Value 000 255 Fan MaxSP Adjust 3 Value 000 255 return ESC 2 When no dmx signal it shows DMX I
11. icity Features Remote control lamp s switch function display light and lamp s using time automaticallay adjust cooling fan s speed Drop 60W power when strobe lens 0 P20 protection rating Protected against the entry of solid bodies larger than 12mm No protection against the entry of liquids O Safety Devices Bipolar circuit breaker with thermal protection Automatic break in power supply in case of overheating or failed operation of cooling system O Cooling Forced ventilation with axial fans O Structure Heat proof plastic module pressing alloy materials O CE Marking In conformity with the European Union Low Voltage Directive 2006 95 CE and Electromagnetic compatibility Directive 2004 108 CE O Two side handles for transportation Device locking PAN TILT mechanisms for transportation and maintenance O Weights and size Box Size 450x430x530 mm N W 18kg G W 21 3kg Flycase Size 2PCS 900x580x7 15 mm N W 36kg G W 76kg Gobo Wheel 1 white 12 gobo Color Wheel please refer to the actual material please refer to the actual material Photometric Date Lux fc 600000 55762 550000 51115 115000 10688 92500 8597 70000 6506 4 3 2 BUS 1 L c oF a 1 T 2 3 4 Distance m Om 3m 5m 10m 15m 20m Diameter m ft in Om 1m 3 3 1 8m 5 9
12. is loose OPlease check the electric parts such as the switch transformer ballast electric capacity piezoresistor filter PCB board controller to motor is short circuit or burn down of the projector couldn t be responsled to the controlling order OPlease check the order is correct to the moving Please check the mechanicalpart is deformation or loose OPlease check the function to the motor socket is loose or drive chip is burn down OPlease check the wire of the motor is cut at zig point OPlease check these function to the motor is damaged On working the pan amp tilt couldn t work normally OPlease check according to the above step by step OPlease check the belt of the X Y is broken OPlease check the X Y direction data to the receiver is damage ORe projector reset DUTY EXONERATIVE AND COPYRIGHT PROTECTION The lamp belongs to consumption products that is not guarantee to keep it in good repair OAny products broken that didn t according to the instruction is not guarantee to keep it in good repair OThe commentary for all the instruction belongs to the supplier in final ONo authorize can t copy OThe information in this manual may be changed in the future the company reserve the right to change the data without any advise
13. let the parts cool down 10 minute at least then begin to install If need to replace the lamp please wait 10 minute again at least to let the lamp cool down completely or which maybe burned down G Please inspect the lens or other moving parts timing and keep them clear and static If find anything damaged or losseness must change a lamp or fix the lamp in order to avoid the accident The light use the strong cool system It is easy for the dirty to be collected Please do clear the hot sak one time two week atleast O After you use the light please check the intake place whether there are some wastepaper please clean it up or the windmill will break down and causing fire TROUBESHOOTING Itis recommended some solution for some normal trouble shooting Any unsolutioned problems should always be handle by the professional person Disconnect the power supply before maintenance the light lWlLamp off Please check if install the suitable lamp Please check the connection of the power supply or switch is ok Please check whether the lamp will reach the end of their life can explode please replace a same description lamp Please measure if the power supply is enough Please check if the operation is correct Please wait 30 minutes at least till the lamp cool down enough then could the connect the power supply which could be normal work Please check whether the DMX 512 controller pass the turn on order Please check the connecti
14. nput Fail CHANNEL FUNCTION CHANNEL CHANNEL CHANNEL MODE COLOUR WHEEL STOP STROBE DIMMER STATIC GOBO CHANGE GOBO ROTATION PRISM PRISM ROTATION FROST 2 3 4 5 6 7 8 9 ZOOM e FOCUS 11 PAN TILT FINE FUNCTION 16 LAMP CONTROL COLOUR WHEEL channel 1 EFFECT 255 FORWARDS ROTATION FROM SLOW TO FAST 128 123 127 BLUE WHITE 118 122 BLUE 112 117 CTB BLUE 107 111 CTB 7200k 102 106 CTO1 CTB 96 101 1 2700 91 95 CTO2 CTO1 86 90 8085 PINK CTO2 75 79 PINK PURPLE PINK 64 69 PURPLE 59 63 GREEN PURPLE 54 58 GREEN 48 53 DARK GREEN GREEN Q 4347 DARK GREEN 38 42 LIGHT BLUE DARK GREEN 3237 LIGHT BLUE 27 31 ORANGE LIGHT BLUE 22 26 ORANGE 16 21 DARK RED ORANGE 41 15 DARK RED 6 10 WHITE DARK RED 05 wz STOPISTROBE channel 2 a BIT EFFECT 250 255 OPEN 210 249 RANDOM STROBE SLOW FAST i 206 209 OPEN amp 181 205 RANDOM OPENING PULSE STROBE SLOW FAST z 156 180 RANDOM CLOSING PULSE STROBE SLOW FAST 152 155 OPEN 127 151 CLOSING PULSE STROBE FROM SLOW TO FAST 126 102 98 101 97 0 OPENING PULSE STROBE FROM SLOW TO FAST OPEN STROBE FAST STROBE SLOW OPEN CLOSED DIMMER channel 3 BIT EFFECT Dimmer intensity from 0 to 100 CLOSED STATIC
15. on of the trigger circuit is loose contact Please check whether the connected point of the trigger point is loose contact faster the connect cable Check menu INFORMATION gt FANS MONITOR gt 1 2 Whether the fan speed in 500RPM above below 500RPM the lamp does not light replace with the specifications of the fan Please check if the switch of the temperature is damaged Check the bottom box driver board WK socket if the resistance 0 between the two line light beam is dark not inhomogeneou When the lamp is to the usage life the light is enough please change a new one for the same description Please check the reflector parts is dirty Keep them clear OPlease measure if the power supply is enough Oo Small adjusting is suitable for change height or screw system till get a ideal light beam TO enter the menu FANCTORY DEFAULT input 2222 enter the COLOR and GOBO regulation until the optical center light shadow is fogging OPlease check the data on the DMX 512 controller is suitable for the electric focus OPlease check the machenical parts is jamging After cleaning please add some temperature durable juice light works interruptly Please check if the fan works normally or mote clogging OPlease check whether the abstract heat have the mote clogging OPlease check if the lamp is to the usag
16. rojectors s control signal output or input by using the or 5 pin pug and socket If need to lengthen the communication cable please make sure the both side of 5 pin plug is one to one one to one two to two three to three Otherwise the communication cable will be interrupted The communicate cable is 2 cord screened cable 759 resistance with each core is atleast a 0 5mm diameter Caution All the inside leading wire of or 5 plug couldn t touch each other or plinth ORecommend to use the DMX signal terminator for the installation to avoid the electronic noise dama ge the digital control signal Simply speaking DMX terminator is an XLR connector with a 1202 1 2W resistor connected across pin 2 and 3 Which is then plugged into the output socket on the last projec tor in the chain Refer to the connection CONTROL PANEL WARNING HOTI Press the switch The projector starts resetting the effects At the same time the following information scrolls on the display minimum please refer to the t H U ON DISTANCE actual material A eM TO FLAMMABLE MATERIAL 12M UP ARROWHEAD Page up or increase DOWN ARROWHEAD Page down or reduce ENTER OK Function RETURE Exit In the choice screen MENU SETTING V4 0 DMX Address Invert Pan return ESC Invert Tilt return ESC Display Reversal BackLig
Download Pdf Manuals
Related Search