Ranger™ Count 2000 Series
Contents
1. OHAUS Ranger Count 2000 Series Instruction Manual Ranger Count 2000 Series EN 1 1 INTRODUCTION This manual contains installation operation and maintenance instructions for the Ranger Count 2000 Series Please read the manual completely before using the scale 1 1 Safety Precautions Please follow these safety precautions e Verify that the AC input voltage printed on the data label matches the local AC power supply e Do not drop loads on the platform e Make sure that the power cord does not pose a potential obstacle or tripping hazard e Use only approved accessories and peripherals Operate the scale only under ambient conditions specified in these instructions Disconnect the scale from the power supply when cleaning Do not operate the scale in hazardous or unstable environments Do not immerse the scale in water or other liquids Do not place the scale upside down on the platform Only use weights within the scale s capacity as specified in these instructions Service should be performed only by authorized personnel 2 INSTALLATION 2 1 Package Contents e Scale e Power Cord e Warranty Card e Pan e Instruction Manual 2 2 Installing Components Install the pan as shown below Press to lock the pan into place Figure 2 1 Installing the pan EN 2 Ranger Count 2000 Series 2 3 Selecting the Location Use the scale on a firm steady surface Avoid locations with excessive air curre2. Calibration R L menu is not accessible Unit is locked at its current setting Zero Range setting is locked at 2 Stable Range setting is locked at 1d Auto Zero Tracking setting is locked at 0 5d Stable Only is locked On Auto Print Continuous is disabled Ib oz is locked Off Ranger Count 2000 Series EN 13 Summary of button navigation functions in menu mode Yes Allows entry into the displayed menu Accepts the displayed setting and advances to the next item No Skips by the displayed menu Rejects the displayed setting or menu item and advances to the next available item Back Moves backwards through the upper and middle level menus Backs out of a list of selectable items to the previous middle level menu Exit Exits from menu directly to the active weighing mode 4 2 Cal Menu Enter this menu to perform calibrations Initial Calibration When the scale is operated for the first time a span calibration is recommended to ensure accurate weighing results Before performing the calibration be sure to have the appropriate calibration weights as listed in table 4 1 Ensure that the LFT switch calibration lock is set to unlocked position See figure 5 1 Or adjust the GEO setting according to your location see table 4 2 Procedure Press and hold Menu until PERU Menu is displayed When the button is released the display will show E A L Press Yes to accept SPAR will t
3. weight or forlibrary record Store an APW value to the current pieces edit recall Zero the COM port application display mode Secondary Off Units Menu Function Tum scale Change the eid Enter user 2 off weighing unit between menu D dio Check Weigh View the Audit Check Count Trail event and Off counters extended press Menu Function Yes No Back Exit Short Press Accept the Advance to Go back to Exit the menu current menu the next the previous Abort the or setting menu or menu or calibration in setting setting progress Increment the Decrement displayed the displayed value value Library Function Yes No Back Exit Short Press Accept the Advance to Go back to Exit the library current the next the previous setting library or library or setting setting Increment the displayed Decrement value the displayed value Ranger Count 2000 Series EN 5 TABLE 3 1 Cont Button 7 89 4 6 c Tare Sample 1 2 3 KE Primary 0 9 e C Tare Sample Function Enter numeric values Enter dot on the Clear the last Perform a tare Display Short Press on the display display character from operation Start the display new APW Secondary l Function Switch between Long Press positive and negative value Notes Short Press Press less than
4. The displayed value is accumulated automatically The gt icon will keep flashing until the weight is removed 3 4 2 Viewing and Clearing Statistical Data When the pan is cleared press the M key to display the statistical information To clear the accumulation data press the Tare key while the statistical information is displayed The display shows L e RCC Press the Yes key to clear the stored data and return to current mode Notes The item must be removed from the pan before the next item can be accumulated Only stable weights are stored to accumulation data Changing the mode will clear the accumulation data 3 5 Check Weighing Press and hold the Target key ChEcF is displayed in the weight window Release the Target key when LJE GH is displayed in the piece weight window Use this mode to compare the weight of items to a target weight range 1 Press the Target key UndEr is displayed in the weight screen The previous under limit will is displayed in the piece weight screen 2 Input the target weight with the numeric keypad The value will be displayed in the count window 3 Press the Yes key to accept the under limit value 8UEr is displayed in the weight screen 4 Repeat step 2 and 3 above to set the over limit If required place an empty container on the pan and press Tare 6 Place sample material on the pan or in the container If the sample weight is under the target weight range the yellow LED will
5. 25 25 24 24 23 23 22 22 67 57 69735 27 27 26 26 25 25 24 24 23 23 22 69 35 7121 28 27 27 26 26 25 25 24 24 23 23 71721 73 16 28 28 27 27 26 26 25 25 24 24 23 73 16 75724 29 28 28 27 27 26 26 25 25 24 24 7524 7152 29 29 28 28 27 27 26 26 25 25 24 77 52 8056 30 29 29 28 28 27 27 26 26 25 25 80 56 85 45 30 30 29 29 28 28 27 27 26 26 25 85 45 90 00 31 30 30 29 29 28 28 27 27 26 26 Ranger Count 2000 Series EN 25 5 LEGAL FOR TRADE When the scale is used in trade or a legally controlled application it must be set up verified and sealed in accordance with local weights and measures regulations It is the responsibility of the purchaser to ensure that all pertinent legal requirements are met The Menu Lock switch limits changes to the Cal Setup Readout Unit and Print menus The switch in type approved models may set some scale settings as required by the approval agency The switch may be secured using paper seals wire seals or plastic ties Note When LEGAL FOR TRADE is set to ON LFT Switch in locked position the menu settings are affected as follows Calibration R L menu is not accessible Unit is locked at its current setting Zero Range setting is locked at 2 Stable Range setting is locked at 1d Auto Zero Tracking setting is locked at 0 5d Stable Only is locked On Auto
6. OFF disabled ON the Header is printed Note See section 7 3 1 for instructions on how to enter Header line Footer Set the status OFF disabled ON the Footer is printed Note See section 7 3 1 for instructions on how to enter Footer line Mode Set the status OFF disabled ON the Mode is printed Unit Set the status OFF disabled ON the Unit is printed Info Set the status OFF disabled ON the Reference Information is printed APW Set the status OFF disabled ON enabled Accu Set the status OFF disabled RESULT the Accumulation result is printed ALL all the Accumulation data is printed Layout LAYGUE Set the format of the data output to a printer or computer Format Set the printing format MULTI a multi line single column style printout is generate SINGLE a single line printout is generated EN 20 Ranger Count 2000 Series Feed Set the paper feed LINE move a paper up one line after printing 4LF move a paper up four lines after printing FORM a form feed is appended to the printout Data Transfer dRER E Output weighing results directly to a PC application OFF disabled ON enabled Windows XP Setup 1 Click Start Menu in Windows XP and click Settings gt open Control Panel 2 Double click Accessibility Options in Control Panel 3 Select the General tab 4 Check Use Serial Keys and click the Settings button 5 Select the Serial Port set the Bau
7. Print Continuous is disabled Ib oz is locked Off 5 1 Settings Before verification and sealing perform the following steps 1 Verify that the menu settings meet the local weights and measures regulations 2 Perform a calibration see section 4 2 3 Set the switch to Locked See figure 5 1 5 2 Verification The local weights and measures official or authorized service agent must perform the verification procedure 5 3 Sealing The local weights and measures official or authorized service agent must apply a Security seal to prevent tampering with the settings Refer to the illustration below for sealing methods Lock Switch Paper Seal Wire Seal Unlocked Locked with Paper Seal Locked with Wire Seal Figure 5 1 Sealing EN 26 Ranger Count 2000 Series 6 MAINTENANCE 6 1 Cleaning The housing may be cleaned with a cloth dampened with a mild detergent if necessary Do not use solvents chemicals alcohol ammonia or abrasives to clean the housing or control panel 6 2 Troubleshooting The following table lists common problems and possible causes and remedies If the problem persists contact OHAUS or your authorized dealer TABLE 6 1 Symptom Possible Cause Remedy Cannot turn on No power to scale Verify connections and voltage Poor accuracy Improper calibration Unstable environment Perform calibration Move scale to suitable location Cannot
8. Recommended 1g 0 002Ib 2g 0 004Ib 4g 0 001Ib 10g 0 02Ib 20g 0 0410 Sample Weight Minimum Recommended 0 005g 0 00001Ib 0 01g 0 000021b 0 020 0 00005lb 0 05g 0 0001Ib 0 1g 0 000210 APW Repeatability 10 0001 kg 10 0002 kg 0 0004 kg 0 001 kg 0 002 kg Linearity 0 0001 kg 0 0002 kg 0 0004 kg 0 001 kg 0 002 kg Weighing Units g kg Ib oz Ib oz Tare Range To capacity by subtraction Stabilization zi second Time 3 LCD with white LED backlight Weight Display 6 digit 7 segment 20 5 mm 0 8 in in characters Keyboard 20 mechanical buttons Battery Operating Time 210 hours with backlight turned off at 20 C Construction ABS plastic housing with 304 stainless steel SST platform Pan Dimensions 225 x 300 mm Net Weight 3 9 kg 8 6 Ib Gross Weight 5 15 kg 11 4 Ib Ranger Count 2000 Series EN 29 7 2 Drawings 311 mm 12 2 in cm mm 12 9 in S Hl OW exea aa hen E 5 EE M LESE 200 Figure 7 1 Dimensions EN 30 Ranger Count 2000 Series 7 3 Communication The scale is equipped with an RS232 interface located under the Options Cover Connecting the scale to a computer enables you to operate the scale from the computer as well as receive data such as displayed weight 7 3 1 Interface Comma
9. light If the sample is within the target weight range the green LED will light If the sample is over the target weight range the red LED will light Ranger Count 2000 Series EN 9 3 6 Check Counting Press and hold the Target key ChEcF is displayed in the weight window Release the Target key when Count is displayed in the piece weight window 1 Press the Target key UndEr is displayed in the weight screen The previous under limit will is displayed in the piece weight screen 2 Input the sample size with the numeric keypad The value will be displayed in the count window 3 Press the Yes key to accept the under limit value 8UEr is displayed in the weight screen 4 Repeat step 2 and 3 above to set the over limit If required place an empty container on the pan and press Tare 6 Place sample material on the pan or in the container If the sample quantity is under the target pieces range the yellow LED will light If the sample is within the target pieces range the green LED will light If the sample is over the target pieces range the red LED will light Positive Check Positive check is used to determine when the material added to the scale is within the target range In this case the UNDER and OVER limits must be positive values The OVER limit must be greater than the UNDER limit Add material to the scale until it is within the ACCEPT green range Negative Check Negative check is used to determine
10. parity Stop bit SEGP Set the number of stop bits 1 1 stop bit 2 2 stop bits Handshake HARdSH Set the flow control method NONE no handshaking ON OFF 2 XON XOFF software handshaking Note Hardware handshaking only available for COM1 menu EN 22 Ranger Count 2000 Series Alternate command RLE CP Define command character for the Print Tare and Zero commands Print Set the alternate command character for Print A to Z Tare Set the alternate command character for Tare A to Z Zero Set the alternate command character for Zero A to Z End COM End Advance to the next menu or return to the top of the current menu 4 8 Lock Menu The Lock menu is a software controlled option which can lock menu settings to prevent tampering Reset no yes Lock Cal off on Lock Setup off on Lock Read off on Lock Unit off on Lock Print off on Lock COM off on End Menu Lock Exit menu Reset rESEE Reset the Lock menu to factory defaults NO noreset YES 69561 Lock Cal L CAL Set the status OFF Calibration menu is not locked ON Calibration menu is locked Lock Setup t SEtuP Set the status OFF Setup menu is not locked ON Setup menu is locked Ranger Count 2000 Series EN 23 Lock Read L ERd Set the status OFF Readout menu is not locked ON Readout menu is locked Lock Unit t Un t Set the status OFF Unit menu is not locked ON Unit menu
11. resolve or describe your problem contact your authorized OHAUS service agent For service assistance or technical support in the United States call toll free 1 800 526 0659 between 8 00 AM and 5 00 PM EST An OHAUS product service specialist will be available to provide assistance Outside the USA please visit our web site www ohaus com to locate the OHAUS office nearest you 6 4 Accessories In Use Cover 30037450 Weighing Below Hook 30025993 Printer Contact Ohaus Communication Cables Contact Ohaus EN 28 Ranger Count 2000 Series 7 TECHNICAL DATA The technical data is valid under the following ambient conditions Operating temperature 10 C to 40 C Relative humidity 20 to 85 relative humidity non condensing Height above sea level Up to 2000 m Power AC power 200 240V 50 60 Hz internal rechargeable sealed lead acid battery Main supply voltage fluctuations up to 10 of the nominal voltage 7 1 Specifications TABLE 7 1 MODEL RC21P1502 RC21P3 RC21P6 RC21P15 RC21P30 Capacity x 1 5kg x 0 00005kg 3kg x 0 0001kg 6kg x 0 0002kg 15kg x 0 0005kg 30kg x 0 001kg Readability 1500g x 0 05g 3000g x 0 1g 60000 x 0 2g 15000g x 0 5g 30000g x 1g Max x d non 3lb x 6lb x 0 0002Ib 15lb x 0 0004lb 3010 6010 x 0 002Ib approved 480z x 0 0020z 960z x 0 0030z 2400z x 0 0060z 4800x x 0 020z 9600z x 0 040z Maximum Displayed 1 30000 Resolution Minimum
12. when the material removed from the scale is within the target range In this case the UNDER and OVER limits are both negative values The UNDER limit must be greater than the OVER limit Place the item to be weighed on the scale and press Tare Remove a portion of the item until it is within the ACCEPT range Zero Check Zero check is used when comparing subsequent samples to an initial reference sample In this case the UNDER limit must be a negative value and the OVER limit must be a positive value Place the reference item on the scale and press Tare Remove the reference sample and place the item to be compared on the scale to determine if it is within the ACCEPT range EN 10 Ranger Count 2000 Series 3 7 Library When an item is processed on a regular basis the item s data may be stored in memory for future use This memory is referred to as the scale s Library Storing a record 1 Press the ID key Stor E and t b are displayed in the weight and piece weight windows respectively The first vacant ID number will blink in the count window Press ID key to save the data to the displayed ID number Alternately a different ID number may be selected using the keypad and then pressing the ID key Note Maximum 30 records from 0 to 29 Retrieving a record 1 2 3 Enter the ID number using the keypad and press the ID key ECALL and L b are displayed in the weight and piece weight windows
13. 1 seconds Long Press Press and hold for more than 2 seconds Weight Piece Weight 1 TNET NET 2 7 275 D DID CI ICI lesse o SOLO s LCD 5 boz pr ape amo amo am e aw e aw DOZ 13 67vY v vv v i APW Lo Wt Lo Auto O T 8 9 10 11 12 Figure 3 2 LCD Displays TABLE 3 2 LCD Symbols Item Description Item Description 1 NET symbol 10 Auto Optimization Symbol 2 Center of Zero symbol 11 Dynamic symbol not used 3 Negative symbol 12 Battery charge symbol 4 Stable weight symbol 13 Pound Ounce Pound Ounce symbols 5 Preset Tare Tare symbols 14 Percent symbol not used 6 Pointer symbols 15 Kilogram gram symbols 7 Accumulation symbol 16 Pieces symbol tonne symbol not used 8 Low Average Piece Weight 17 Scale symbol not used symbol 9 Low Sample Weight Symbol EN 6 Ranger Count 2000 Series The colored LED indicators on the left side of the control panel are used in Checkweighing mode section 3 5 and will light up according to the following rules Z Red Loads gt Upper limit Green Loads lt Lower limit and gt Upper limit V Yellow Loads gt Lower limit Power Input Weigh Below Access T M E 9 2 2 Interface Port below cover N 0 N Lock Switch Figure 3 3 Below view of Ranger Count 2000 3 2 Tur
14. 2 11 11 10 10 9 9 8 8 7 7 31 56 33 09 12 12 11 11 10 10 9 9 8 8 7 3309 34721 13 12 12 11 11 10 10 9 9 8 8 34 21 35791 13 13 12 12 11 11 10 10 9 9 8 35 31 36 41 14 13 13 12 12 11 11 10 10 9 9 36 41 37 50 14 14 13 13 12 12 11 11 10 10 9 37 50 3858 15 14 14 13 13 12 12 11 11 10 10 38 58 40 05 15 15 14 14 13 13 12 12 11 11 10 40 05 41 12 16 15 15 14 14 13 13 12 12 11 11 41 12 42719 16 16 15 15 14 14 13 13 12 12 11 42 19 4326 17 16 16 15 15 14 14 13 13 12 12 43 26 4432 17 17 16 16 15 15 14 14 13 13 12 44932 45 38 18 17 17 16 16 15 15 14 14 13 13 45 38 46745 18 18 17 17 16 16 15 15 14 14 13 46 45 4751 19 18 18 17 17 16 16 15 15 14 14 4751 48758 19 19 18 18 17 17 16 16 15 15 14 48958 50 06 20 19 19 18 18 17 17 16 16 15 15 50 06 51 13 20 20 19 19 18 18 17 17 16 16 15 51 13 5222 21 20 20 19 19 18 18 17 17 16 16 52722 5331 21 21 20 20 19 19 18 18 17 17 16 53931 5441 22 21 21 20 20 19 19 18 18 17 17 5441 55 52 22 22 21 21 20 20 19 19 18 18 17 55 2 5704 23 22 22 21 21 20 20 19 19 18 18 57 04 58 17 23 23 22 22 21 21 20 20 19 19 18 58 17 59732 24 23 23 22 22 21 21 20 20 19 19 59 32 60 49 24 24 23 23 22 22 21 21 20 20 19 60 49 62 90 25 24 24 23 23 22 22 21 21 20 20 62 90 63 30 25 25 24 24 23 23 22 22 21 21 20 63 30 64 55 26 25 25 24 24 23 23 22 22 21 21 64 55 66724 26 26 25 25 24 24 23 23 22 22 21 66 24 67757 27 26 26
15. acking functionality OFF disabled 0 5d the display will maintain zero until a change of 0 5 divisions per second has been exceeded 1d the display will maintain zero until a change of 1 divisions per second has been exceeded 3d the display will maintain zero until a change of 3 divisions per second has been exceeded Ranger Count 2000 Series EN 17 Light L GHE Sets backlight functionality OFF always off ON always on AUTO turns on when a button is pressed or the displayed weight changes Auto off R GFF Set the automatic shut off functionality OFF disabled 1 powers off after 1 minute of no activity 5 powers off after 5 minute of no activity 10 powers off after 10 minute of no activity 4 5 Unit Menu This menu activates units so they will be accessible with the Units button The units in the menu must be turned on to be active Note Available units vary by model and local regulations 4 6 Print Menu Enter this menu to set printing parameters Reset no yes Stable Only off on Auto Print off on stable interval continuous accept Content Part Number gt off on Result gt off on Gross off on Net gt off on Tare off on Header off on Footer gt off on Mode off on Unit off on Info gt off on APW off on Accu off result all Layout Format gt S M Feed Line 4 Lines form Data Transfer off on Print L
16. calibrate LFT locked See chapter 5 for information Cannot access mode Mode not enabled Enter menu and enable mode Cannot access unit Unit not enabled Enter menu and enable unit Battery icon flashing Low Battery error Connect scale to AC power and charge the battery Weight reading exceeds Power On Err B Power On Error Zoro limit Weight reading below Power On Zero Err B 2 Power On Error limit Weight reading exceeds Overload Err 8 3 Over Range Error limit Err B 4 Under Range Error Weight reading below Underload limit Err 5 Tare out of range Adjust tare value to be within range Err 56 Display overflow Weight exceeds 6 digits Err 5 Calibration data error Calibration data not present Bus Displayed during tare setting zero Hd aan y setting printing fig Action not allowed Function not executed Po value outside allowed CAL E pur E nt Move the scale to suitable location 9 Use correct calibration weight Low reference weight Lo cEF warning Increase reference weight Reference weight too small Weight Unacceptable reference on the pan is too small to define a rEF Err weight valid reference weight Increase reference weight Battery fails to charge fully Battery is defective Have battery replaced by Ohaus authorized service dealer Ranger Count 2000 Series EN 27 6 3 Service Information If the troubleshooting section does not
17. d rate to 9600 and click OK 6 Close the Control Panel 7 Run Excel to open one blank sheet Focus the cursor on one item At this time if scale sends data to the PC through the RS232 port the data will be put into the cell and the cursor will automatically move to the next vertical cell Notes For Windows 7 setup contact Ohaus If the weighing value is a negative number set the target cell in TEXT format Otherwise Excel will not distinguish it as a negative number Please do not use this function during continuous printing Print Library P L 4 Print the library data No disabled Yes All library records stored in memory are printed End Print End Advance to the next menu or return to the top of the current menu Ranger Count 2000 Series EN 21 4 7 COM Menu Enter this menu to define communication parameters Reset no yes Baud Rate 300 9600 19200 Parity 7 even 7 odd 7 none 8 none Stop bit 1 2 Handshake none On Off Alternate command Print A P Z Tare A T Z Zero A Z End COM Exit menu Reset rESEE Reset the COM menu to factory defaults NO noreset YES 69561 Baud Rate bRud Set the baud rate 300 bps 600 bps 1200 1200 bps 2400 2400 bps 4800 bps 9600 bps 19200 19200 bps Parity PAr bY Set the data bits and parity 7 EVEN 7 data bits even parity 7 ODD 7 data bits odd parity 7NONE 7 data bits no parity 8NONE 8 data bits no
18. e the Weigh Below hook feature remove power from the scale and remove the protective cover for the weigh below opening Install the hook accessory into the access hole at the bottom of the scale as shown Do not over tighten tighten finger tight Mount the scale onto an appropriate assembly that allows free working space below the hook See figure 3 4 Note Never allow the scale to rest directly on the hook Weigh Below Hook Access Figure 3 4 Setup for the Weigh Below Hook EN 12 Ranger Count 2000 Series 4 MENU SETTINGS The User Menu allows the customizing of scale settings Note Additional Sub Menus may be available if Interface Options are installed See Interface User Manual for the additional setting information 4 1 Menu Navigation User Menu Menu C A L S E t U P r E A d U n i t Span Reset Reset Reset Lin Pwr Un Stable kg Menu GEO Zero Filter g Items End A Opt AZT Ib A Tare Light Oz Bp Opt A Off Ib oz Bp Sig End End Bp Key Accum End P r i n t C O M L O C k E n d Reset Reset L Cal Stable Baud L Setup Menu A Print Parity L Read Items Contnt Stop L Unit Layout Handsh L Print Data Tr Alt Cm L COM End End End Notes Some units may not be available in all models When LEGAL FOR TRADE is set to ON LFT Switch in locked position the menu settings are affected as follows
19. enu or return to the top of the current menu 4 3 Setup Menu Enter this menu to set scale parameters Reset Power on unit Zero Range Auto Opt Auto Tare Beeper Opt Beeper Signal Beeper Key Accumulation End Setup Reset r ESEt no yes auto kg g Ib oz Ib oz 296 1096 off on on off on acc off on off Accept Under Over Under Over off on off auto manual Exit menu Reset the Setup menu to factory defaults NO not reset YES 6561 Ranger Count 2000 Series EN 15 Power on unit Pbur Ufi Set the unit of measure displayed at startup auto last unit in use when turned off kg kilograms g grams Ib pounds OZ ounces lb oz pound ounces Zero Range 2 Set the percentage of scale capacity that may be zeroed 2 zeroup to 2 percent of capacity 10 zero up to 10 percent of capacity Auto Opt R GPE Set the automatic optimization functionality OFF disabled ON APW automatically optimized Auto Tare R ER E Set the automatic tare functionality OFF Automatic Tare is disabled ON the first stable gross weight is tared ON ACC stable gross loads within the accept limits are tared in Checkweigh mode Beeper Opt bP GPt Set whether or not the beeper sounds when APW has been optimized OFF disabled ON enabled Beeper Signal bP 5 16 Set how the beeper responds in Check Weighing mode OFF the beeper is disabled ACCEPT
20. g the scale on battery power TABLE 2 1 Symbol Charge Level O to 10 Remaining n 11 to 40 Remaining um 41 to 70 96 Remaining TT 71 to 100 Remaining Notes When battery symbol blinks fast approximately 30 minutes working time is left When Lo bRE is displayed the scale will shut off Charging the scale must be performed in a dry environment CAUTION Battery is to be replaced only by an authorized Ohaus service dealer Risk of explosion can occur if the rechargeable battery is replaced with the wrong type or if it is not properly connected Dispose of the lead acid battery according to local laws and regulations EN 4 Ranger Count 2000 Series 3 OPERATION 3 1 Displays Weight Piece Weight 0 2888 20 0 0 0 0 4 Doon Es a i Ttc Vac aiat CT Yes lie LI LI L 0 00 00 H Ls Back Exit Y vov Y Y 1 2 3 ID APW BURGI L2 2 v 0 5 Tare Figure 3 1 Ranger Count 2000 Control panel with LCD displays TABLE 3 1 Control Functions On Zero Print M Button Off Units Target Menu APW Yes No Back Exit Primary ON ZERO PRINT Target M ID APW Function Turn scale Send the Initiate the Accumulate the ID number input Display Short Press on displayed function ofthe
21. hen be shown Press Yes to begin the span calibration 0 kg will be displayed Press Yes to accept 6 will be displayed while zero reading is stored Next the display shows the calibration weight value Place the specified calibration mass on the pan Press Yes to accept the weight or No to select an alternate weight 6 will be displayed while the reading is stored The display will show donE if the calibration was successful The scale returns to the previous application mode and is ready for use TABLE 4 1 Suggested Span Calibration Mass sold separately Max Mass Max Mass 1500g 1 5kg 310 15000g 15kg 3010 3000g 3kg 610 30000g 30kg 6010 6000g 6kg 1510 Note Pound masses are used when calibrating in the Ib unit EN 14 Ranger Count 2000 Series Span Linearity Geographic Adjustment End Calibration Perform Perform Set 0 12 31 Exit menu Bold always represents factory default value Span SPAR Initiates a span calibration procedure zero and span Lin t 1f Initiates a linearity calibration procedure zero mid point and span GEO ceo Geographical Adjustment Factor GEO is used to adjust the calibration based on the current location Settings from 0 to 31 are available with 12 being the default Refer to table 4 2 to determine the GEO factor that corresponds to your location End Cal End Advance to the next m
22. ib yes no End Print Exit menu Reset rESEE Reset the Print menu to factory defaults NO 6561 YES 69561 EN 18 Ranger Count 2000 Series Stable Only SERbLE Set the printing criteria OFF values are printed immediately ON values are only printed when the stability criteria are met Auto Print A Pr int Set the automatic printing functionality OFF disabled ON STAB printing occurs each time the stability criteria are met INTER printing occurs at the defined interval ACCEPT printing occurs each time the display is within the Checkweigh accept range and stability criteria are met CONT printing occurs continuously When ON STAB is selected set the condition for printing where LOAD printing occurs when the load is stable and greater than zero LOAD ZR printing occurs when any load is stable and equal to or greater than zero When INTER is selected set the Print Interval 1 to 3600 seconds Content Cann Define the content of the printed data Part Number Set the status OFF disabled ON the part number is printed Result Set the status OFF disabled ON the displayed reading is printed Gross Set the status OFF disabled ON the gross weight is printed Net Set the status OFF disabled ON the net weight is printed Tare Set the status OFF disabled ON the Tare weight is printed Ranger Count 2000 Series EN 19 Header Set the status
23. ins PIN 2 TXD PIN 3 RXD PIN 5 Ground VGN TEN aN Ta MOODY SAN Cem EN ren 9 8 7 6 Figure 7 2 15232 Pins Ranger Count 2000 Series EN 31 7 4 Printouts The following sample print outs are generated by the Print button P Command or alternate print command The content of the printout is defined in the Print Content menu item A maximum of 24 characters can be printed on each line 7 um LEAL AR LF A PN 123456789926 926 PCS 12 33 kg G 11 11 kg NET 1 22 kg T APW 1 2 g N 3 ACC 2875 Pcs VM WU MU en ur yvy Description Part Number line Result line Gross value line Net value line Tare value line Information line Accumulation line Accumulation line Comment If Printx gt Content gt P N is ON If Printx gt Content gt Result is ON If Printx gt Content gt Gross is ON and a tare value is entered If Printx gt Content gt Net is ON and a tare value is entered If Printx gt Content gt Tare is ON and a tare value is entered If Printx gt Content gt Info is ON If Printx gt Content gt Accu is All If Printx gt Content gt Accu is All EN 32 Ranger Count 2000 Series LIMITED WARRANTY OHAUS products are warranted against defects in materials and workmanship from the date of delivery through the duration of the warranty period During the warranty period OHAUS will repair or at its option replace any component s that pro
24. is locked Lock Print L Pr wnt Set the status OFF Print menu is not locked ON Print menu is locked Lock COM L COP Set the status OFF COM menu is not locked ON COM menu is locked End Lock End Advance to the next menu or return to the top of the current menu 4 9 End Menu Press Yes to exit the menu and return to the current application mode Press No to advance to the Calibration menu EN 24 Ranger Count 2000 Series TABLE 4 2 GEO CODES Elevation in meters 0 325 650 975 1300 1625 1950 2275 2600 2925 3250 325 650 975 1300 1625 1950 2275 2600 2925 3250 3575 Elevation in feet 0 1060 2130 3200 4260 5330 6400 7460 8530 9600 10660 1060 2130 3200 4260 5330 6400 7460 8530 9600 10660 11730 Latitude GEO value 000 5 6 5 4 4 3 3 2 2 1 1 0 0 546 2 5 5 4 4 3 3 2 2 1 1 0 952 12 44 6 5 5 4 4 3 3 2 2 1 1 12 44 1506 6 6 5 5 4 4 3 3 2 2 1 1506 17 10 7 6 6 5 5 4 4 3 3 2 2 17 10 19 02 7 7 6 6 5 5 4 4 3 3 2 19 02 20 45 8 7 7 6 6 5 5 4 4 3 3 20 45 22722 8 8 7 7 6 6 5 5 4 4 3 22 22 23 54 9 8 8 7 7 6 6 5 5 4 4 23 54 25 21 9 9 8 8 7 7 6 6 5 5 4 25 21 26 45 10 9 9 8 8 7 7 6 6 5 5 26 45 28 06 10 10 9 9 8 8 7 7 6 6 5 28 06 29 25 11 10 10 9 9 8 8 7 7 6 6 29 25 30 41 11 11 10 10 9 9 8 8 7 7 6 30 41 31 56 1
25. move the samples from the container weight window will now display a negative net reading 4 Input the sample size with the numeric keypad The value will be displayed in the count window Alternatively the Sample key can be used instead Pressing the Sample key and is displayed in the count window Then input the sample size value only integer 5 Press the Sample key will be displayed in both the piece window and the count window 6 The established APW and count will be displayed Entering a known APW 1 Press the APW key will be displayed in the piece window 2 Input the APW value 3 Press the APW key the new APW value will be displayed in piece weight window 3 3 Simple Counting After a valid APW is established if required place a container on the pan and press Tare 2 Place the sample on the pan 3 The quantity will be displayed in the count window EN 8 Ranger Count 2000 Series 3 4 Accumulation and Statistics The Accumulation feature enables manual or automatic totalizing of displayed values Statistical data is stored in memory for review and printing Accumulation works together with Check mode 3 4 1 Accumulating Displayed Values With ACCUMULATE set to MANUAL place the item on the scale and press the M key to add the weight to accumulation data The gt icon will keep flashing until the weight is removed With ACCUMULATE set to AUTO place the item on the scale
26. nds Communicate to the scale using the command characters listed in Table 7 2 TABLE 7 2 Command Function IP Immediate Print of displayed weight stable or unstable P Print displayed weight stable or unstable CP Continuous Print SP Print on Stability xS OS Turn off Stable Only menu item and allow unstable print 1S Turn on Stable Only menu item and only print stable print xP Interval Print x Print Interval 1 3600 sec OP turns auto print OFF Z Same as pressing Zero Key T Same as pressing Tare Key xT Download Tare value in grams positive values only Sending OT clears tare if allowed PU Print current unit g kg lb oz Ib oz t c custom xU Set scale to unit x 12g 2 kg 3 0 4 02 5 0 02 6 t xM Set scale to mode x M will scroll to next enabled mode Version print name software revision and LFT ON if LFT is set PY ON H x text Enter Header line where x line number 1 to 5 text header text up to 24 alphanumeric characters F x text Enter Footer line where x line number 1 to 2 text rear text up to 24 alphanumeric characters Global reset to reset all menu settings to the original factory EscR defaults Escape key R Key 7 3 2 Connections for RS232 The 9 pin female subminiature connector COMI is provided for interfacing to other devices The pin connections are as follows Active p
27. ning Scale On Off To turn the scale on press and hold the On Zero Off button for 1 second The scale performs a display test momentarily displays the software version and then enters the active weighing mode To turn the scale off press and hold the On Zero Off button until OFF is displayed 3 3 Counting Ranger Count 2000 has three display areas Weight Piece Weight and Count information are displayed in these areas respectively 3 3 1 Preset tare Enter a value with the numeric keypad The value will be displayed in the Count window Pressing Tare key the value in current unit will then be saved as the preset tare To clear the tare value clear the pan and press Tare key Ranger Count 2000 Series EN 7 3 3 2 APW Establishment If there is no APW established both the piece weight display and the count display will show 0 Positive Sampling 1 2 4 Place the sample on the pan Input the sample size with the numeric keypad The value is displayed in the count window Alternatively the Sample key can be used instead Pressing the Sample key and is displayed in the count window Then input the sample size value only integer Press the Sample key will be displayed in both the piece window and the count window The established APW and count will be displayed Negative sampling 1 Place container with the samples on the pan 2 Tare the scale a NET 0 will be displayed 3 Re
28. nt vibrations heat sources or rapid temperature changes Allow sufficient space around the scale 2 4 Leveling the Equipment The Ranger Count Series has a level indicator as a reminder that the scale should be leveled for accurate weighing To level the scale adjust the feet so the bubble is centered in the circle Be sure the equipment is level each time its location is changed Level Indicator YES NO Adjustable feet Figure 2 2 Level indicator 2 5 Connecting Power AC power is used to power the scale when battery power is not needed First connect the AC power cord supplied to the power input jack then connect the AC plug to an electrical outlet Figure 2 3A Connect the Figure 2 3B Connect the AC AC power plug to the input power plug to the proper AC jack on the back of scale supply Ranger Count 2000 Series EN 3 2 5 1 Battery Power The scale can be used on AC power immediately The scale will automatically switch to battery operation if there is a power failure or the power cord is removed The scale can be operated during charging and the battery is protected against overcharging During battery operation the battery symbol see item 9 in Figure 3 2 indicates the battery charge level The scale will automatically turn off when the batteries are fully discharged For maximum operating time the battery should be charged at room temperature Allow the battery to charge for 12 hours before usin
29. respectively ID number is displayed in the weight window Press the ID or Yes key cECRLL is displayed and the data is retrieved Editing a record 1 Enter the ID number using the keypad and press the ID key rECRLL and L b are displayed in the weight and piece weight windows respectively Long press the ID key Ed amp and t b are momentarily displayed in the weight and piece weight windows respectivel Part number is displayed in the weight and piece weight windows Default setting is 000000 000000 Use the keypad to enter part number if required Press the Yes key to save the part number and advance to the preset Tare setting Use the keypad to enter a preset Tare value if required Press the Yes key to save the preset Tare value and advance to the APW setting Use the keypad to enter a new APW value if required Press the Yes key to save the APW and advance to the Limits setting Use the keypad to enter new under and over limits if required Press the Yes key to save the limits SAVE is displayed in the weight window Press the Yes key to save the data Ranger Count 2000 Series EN 11 Clearing a record 1 Enter the ID number using the keypad and press the ID key c ECRLL and b are displayed in the weight and piece weight windows respectively 2 Press the C key dELEEE is displayed in the weight window Press the Yes key to delete the data 3 8 Additional Features To us
30. the beeper will sound when the weight is within the Accept range UNDER the beeper will sound when the weight is below the Under setting OVER the beeper will sound when the weight is above the Over setting UNDER OVER the beeper will sound when the weight is below the Under setting or above the Over setting Key Beeper bP FEY Set whether the beeper sounds when a button is pressed OFF no sound ON sound EN 16 Ranger Count 2000 Series Accumulation RECur Set the accumulation functionality OFF accumulation disabled AUTO automatic accumulation MAN manual accumulation End Setup End Advance to the next menu or return to the top of the current menu 4 4 Readout Menu Enter this menu to set user preferences Reset no yes Stable Range 0 5 1 2 5 Filter low medium high Auto Zero Tracking off 0 5 1 3 Light off on auto Auto off off 1 5 10 End Readout Exit menu Reset r ESEt Reset the Read menu to factory defaults NO not reset YES reset Stable Range SEAbLE Set the amount the reading can vary while the stability symbol remains on 0 50 0 5 scale division 1d 1 scale division 2d 2 scale division 5d 5 scale division Filter F Le Er Set the amount of signal filtering LOW less stability faster stabilization time MED normal stability stabilization time HI greater stability slower stabilization time Auto Zero Tracking Ret Set the automatic zero tr
31. ves to be defective at no charge provided that the product is returned freight prepaid to OHAUS This warranty does not apply if the product has been damaged by accident or misuse exposed to radioactive or corrosive materials has foreign material penetrating to the inside of the product or as a result of service or modification by other than OHAUS In lieu of a properly returned warranty registration card the warranty period shall begin on the date of shipment to the authorized dealer No other express or implied warranty is given by OHAUS Corporation OHAUS Corporation shall not be liable for any consequential damages As warranty legislation differs from state to state and country to country please contact OHAUS or your local OHAUS dealer for further details 4 OHAUS OHAUS Corporation 7 Campus Drive Suite 310 Parsippany NJ 07054 USA Tel 1 973 377 9000 Fax 1 973 944 7177 With offices worldwide Con oficinas alrededor del mundo Avec des bureaux dans le monde entier Weltweite Gesh ftsstellen Con uffici in tutto il mondo www ohaus com 3 0 0 3 7 4 5 9 x P N 30037459B 2012 OHAUS Corporation all rights reserved todos los derechos reservados tous droits r serv s Alle Rechte vorbehalten tutti i diritti riservati Printed in China Impreso en la China Imprim en Chine Gedruckt in China Stampato in Cina
Download Pdf Manuals
Related Search