Home

Here

1. m Power Cable m USB Cable au 5 m SD Memory Card 2GB m User Manual OO Power Input SD memory card slot AV OUT Power button USB slot Mode button blackbox mode playback list backward Play button play stop blackbox event video Movie button continuous record playback list forward Status LED Microphone Speaker 1 Camera Module VGA 640x480 CMOS sensor and F 1 8 hi end lens with 160 5 viewing angle 121 horizontal 88 vertical e 15fps video record speed at daylight night parking mode 2 G Sensor Max 8G measuring capability at forward backward up down and left right direction e Max 100 point of measurement data per second for more accurate record during accident event 3 GPS SirfStar Ill supported Provide Longitude Latitude speed direction altitude information Capable of tracking actual location of event accident by connecting to local road street map information 4 Internal and external memory 1GB internal N AN D flash memory Able to support SD SDHC memory card Records all event accident into builtin internal memory for more reliable data record All event accident information can also automatically be saved into external memory card 5 Video Audio output Can link to external video audio devices with A V IN e g car navigator N ot includ
2. Use of non complied AV cable will cause damage to the device User has to take responsibility for device damage or malfunction by use of inappropriate AV cable Video Out YELLOW External Switch Audio Out WHITE RED 13 1 Power ON OFF Power on Device activates itself when the power is connected In addition device activates with its internal battery by pressing device power button even when it is not connected to external power supply e g vehicle battery power supply In this case no other feature other than video audio player will be enabled power off W hen power is disconnected device will automatically be deactivated after few seconds The device can also be deactivated by pressing device s power button for 2 seconds or longer During continuous power supply mode from corresponding vehicle device will monitor vehicle s battery level and deactivates itself when the battery drops below specified voltage level Similarly devices will also deactivate itself when it detects low battery on builtin battery power supply mode The green and red LED will blink in turns fast before it turns off completely x How to turn off the power manually User can deactivate device manually by pushing power button and hold for more than 5 seconds Recommended not to deactivate device manually when the device is recording the event 2 Blackbox Mode Event record Mode Red lighted LED signals that the black
3. Please check and reposition the device when it is exposed to extreme shocks or vibration for a period of time Device will not record appropriate videos if the orientation of blackbox is out from user s intention or holder is loose due to the extreme shocks or vibration In this case user shall park the vehicle at safe place for correction Recording of video quality may be affected for vehicle having heavily tinted windshield Please check the windshield condition before installing the device Please use the power cable supplied for device power from vehicle and power supply shall not exceed indicated voltage range in the specification Using other cable aside from cable supplied or attaching the device to a wrong power supply can lead to system defect malfunction and can cause fire Please do not place any other device or object in front or top of the device after installation GPS signal may be hindered or affected when obstacles are placed along the signal path or sun protection film is installed on windshield Please take note that a video may not be recorded correctly when driving through tunnel under high beam from other side of the road against the direct sunlight and during the night Do not operate or look at the device when driving Itcan lead to unwanted vehicle accident Please take note that under extreme shock the device may not record video by device breakdown m Main Device m Holder
4. UPG RADIN G THE FIRM W ARE 1 Installation Save and unzip truei zip file from SD card provided to a user defined folder From the uncompressed files double click to run truei exe to start true viewer x Note For the latest software update please check the website at www true i com 2 How to use true i Viewer Once the program is executed truei viewer is displayed on the PC screen as below Click O PEN button on screen and select and the BLACKBO X folder from SD card or True device attached to the PC using USB cable Ey Re Ee Please select a RlarkRnx falder se M BSC amp Su 02a C cs 3 UA D DVD RW Sele E AQ DVD CeHIE F 4 em USA OAS G BLACKBOX MOVIE S HANMAN2 m Clicking a file in BLAC KBO X folder as shown on the screen shot below the true Viewer will open and play the file recorded 17 On the bottom of video screen panel time speed and shock values will be displayed Directly below the video screen panel amplitude acceleration shock will be displayed before and after the event recorded And the left bottom of truei Viewer screen a simulated cockpit is displayed with vehicle s speed direction and acceleration information Actual footage of event will be displayed on the Google map when the PC is connected to the internet X Caution The map will not be displaye
5. device Hanman Technology is not liable for any compensation or legal responsibility of vehicle accidents that caused by operating the device when vehicle was in motion 4 Device specification change Product spec software user manual and or others related to the product are subject to change without prior notice By opening the plastic wrap of the device user has agreed to the all terms as outlined above For any reason user does not agree the above mentioned please do not open the device wrap and return the device to where the product was purchased from For your safety and to protect the device from mishandling and through unintended incident please read and follow instructions as outlined below Do not open repair and or make any change to the device It can lead to system malfunction or defects which Hanman Technology will not be liable for Do not use water or flammable substance when cleaning the device It can cause system defect as well as potential fire or electronic short circuit Do not apply intentional shocks or insert substance into the device It can cause ststem defect or fire and or electronic short circuit Please keep the camera lens clean and free of any obstacles within the lens viewing angle to obtain clean and precise video during the recording It is suggested not to place objects near the blackbox and windshield as they can be seen in the video through reflection from the windshield
6. SMA HAEL SARE AUX Dott MSIZA ux MI2000 21S 0 me Sz Zo Aol thet SE HSE AAEL OXSESMO TU YO E74 UA BS SS AS UW 7154 MAHSol Sst WAY Aol IBS Bote ASRS7 Ztoe AEU OUT LS Al SHAS LE 7S AHAN eo HEME MAIS FAI al zloty FAAL xX O HEME HEURA RESH MAHA OUR HSE AAA Power Supply 12 24V AIX ni 284 TSHR aaz o 70 Re 10Y oldo 528 AE RS ae HET EE 97 Shs a FARNE oo S2 FEA FAH SE SS MEME ES se eee neso ZEEN Eol VHS olol S28 AEE 25E BS ar ze gag ZESA PE Sas CHS SEINO DEF HENASIM AI Al ae5 stew OEFA DAO 5 48 Fal Bou Balm A HERBE Pet ES nee SAL agas ANIA 42 RS HES AAR EAST BS PL EE AS SES ASST QI got Salt Sse 4 IE HUE AIX TO Aal7 FHSS BS RAE RAS MEAE EEEE es 21540 24 4e AA Ss yeast 7 ANSE ARR VER SO E 780 SIA ZS ABH OM D H5779 RCE ljo TAlo HAISIAS BS 7IE MEE XI SAP OL QE geo lst 4e ga sal KI AHAMIE AEA of ARNO el E HE5 TZIO site AS Power Consumption lt 1W Surveillance mode 20 Operating Temperature x The specification is subject to change without prior notice 20 70 C AE 8 792 OIL HHS A wg 7HS LIT HES Bold SS WS EYS ASS BE JEHAN HS5 FAAS AE BAS Ase ASS HZ0 SEU AS SCH lst HO APE NL AE HS Al HS HSS DAA FAH BILICHE AE SO Clst El SPE Ag
7. be turned into USB memory device by connecting USB cable provided onto device and PC s USB port At this event orange LED will be turned on Device will be recognized as USB memory device by PC W hen in USB memory mode 1GB of internal memory can all be used USB memory mode can be deactivated automatically by disconnecting USB cable from its device 15 16 1 Download and save the latest firmware available from Download Center in www true i com to user defined folder or an SD card 2 Unzip the downloaded file to uncompress User will see the files named hmbs200 bin and setup hms as successful unzip of the downloaded file 3 Copy and paste the files into SD card if user saved the files in a PC or other storage device 4 Remove the power supply cable from device and make sure that the device power is completely turned off 5 Insert the SD card with the downloaded files 6 Connect back the power supply cable to device 7 ORANGE LED will be turned on and System will strat upgrading the firmware automatically 8 Updating the firmware may take up to 1 minutes and wait until system reboots the device and RED LED will be turned on 9 If firmware is updated successfully to the device the hmbs200 bin file will be automatically deleted from SD card and device will create BLACKBO X and MO VIE folders x Caution DO NOTTURN OFF THE POW ER SUPPLY AND DO NOT PRESS ANY BUTTONS W HILE
8. box is in event record mode When event such as specified acceleration or impact is detected on its corresponding vehicle 20sec video audio accel GPS info is recorded each before and after the event During event recording interval red LED will be flickered and it will go back to stable RED LED again when the record is completed Parking monitoring mode Surveillance mode Parking monitoring mode activates with GREEN LED lighted when pressing MODE button continuously until beep sound In this parking monitoring mode 20 secs video audio accel GPS info will be saved when shock is detected or visual motion is detected on the camera viewing span angle During this record interval the LED light will be flickered and will activate again when record is completed Mode interchangeability Can interchange event shock record mode and parking monitoring mode by pressing MODE button continuously until a beep sound is heard User can recognize each mode by LED lighted color Depending on car s condition device will automatically set its record mode X Caution Please check the device mode LED before you are driving or 14 parking the vehicle Device may not interchange modes automatically in certain circumstance You may set appropriate mode by pressing the M O DE button Manual record In any mode user can record 20 sec of video audio accel GPS info by pressing any one of three buttons or using external co
9. d when PC is not connected to the internet or valid GPS data is notrecorded during the event 3 Viewer Configuration User can configure truei blackbox by pressing SETUP button located on the upper right side of the viewer Select blackbox recording mode Select Event and configure record event mode to user defined shock level whereas MPEG4 configure continuous record mode Select MPEG 4 mode and configure recording time interval For example choosing 10min on the pull down menu will allow device to save every 10 mins during continuous record mode 18 Power On event MP4REC jOmin Rec Mode Interval Sensitivity High V Audio On off Acceleration V Sound On off 0 aoe Shock level can be adjusted If the accelerator value is selected too high device would not be able to detect shock needed for appropriate event record Likewise selecting very low shock level will allow device to record even a small shock event Therefore user is suggested to find an appropriate level to user s need Acceleration level can be adjusted Define the level of acceleration or deceleration that device will detect Motion detection level can be adjusted Setting level maximum will focus object close to the device lens whereas setting the level minimum can detect objects farthest away from the device viewing angle The motion detection level should be set appropriately to user s e
10. ed using builtin AV output socket 6 Built in Emergency back up battery W ith Lithium polymer battery builtin Can record event accident even without power supply from external power source e Maximum 10min battery life after fully charged e Battery protection through builtin thermal sensing capability 7 Built in internal speaker 0 4W speaker for event alarming sound 8 USB Mass storage device For file transfer to PC from builtin 1G B internal memory through PC USB slot Can be used as external memory device 8 9 Compact and Light weight Compact 77mm H x54mm V x18mm T and 33mm incl lens and holder Lightweight less than 100g incl holder 10 Event record mode Record total 40sec of video audio acceleration GPS information before after event at 15fps 11 Continuous record mode e Max 25 fps video and 192kbps mono audio record capability using M PEG 4 codec User configurable record time length 12 Parking monitoring mode Surveillance mode Can monitor events during parking mode when continuous power is available vehicle power Low power consumption less than 1W by build in Special power saving feature Can record total 40sec video audio acceleration information before and after event or when motion is detected on the camera viewing span angle Builtin power monitoring feature and auto power cutoff to prevent full vehicle battery discharge Can interchan
11. ge automatically between event record mode and parking monitoring mode 13 Emergency event recording control button Link available for external emergency control button not provided optional Can record total 40sec video audio acceleration GPS information through internal record button or external emergency button required optional emergency recording button 14 Built in video audio player Can play video audio using its builtin player through AV output socket Can link directly to display device or GPS navigator through AV input socket Can be readily displayed on display device or GPS navigator s monitor screen without PC 1 How to attach device holder Attach device holder on the windshield facing user Make sure that the holder does not block or obstruct the camera lens viewing angle Once proper location is found user can easily attach the holder onto the front windshield after removing the protection layer from 3M s tape 2 How to mount device to the holder W hen attaching holder to the main device please tilt and push in the holder to the device as shown in the picture below The device has a locking mechanism to keep the holder in place Please be warned that the holder or device can be damaged when used with excessive force Step 1 Align the device to the device holder Step 3 Dyn Slide in the device User will be able to feel the device is locked onto the lock
12. ing in mechanism 10 3 How to detach device from holder W hen detaching the device from the holder user should tilt the device slightly After the holder is tilted user should use his her thumb to hold on to the front of the device and use your index finger to push the device down from the holder as shown as in the picture below Step 1 Place your index finger on top and user use your thumb to support the holder as shown in the picture Push with your index finger downward i and thumb to support Step 3 Step 4 After it passes through the first locking mechanism tilt the device as shown You can now successfully remove the device 11 ation 4 Adjustment of camera angle Using provided 2 directional holder the device lens viewing angle can be adjusted User can find the desirable viewing angle and rotate the knob clock wise to fix the viewing angle If viewing angle requires new adjustment rotate the knob counter clockwise to release the angle 5 Plug in of power cable Use only the cigarette power cable provided User must use cigarette power cable for power supply from vehicle s cigarette lighter socket For continuous power supply user will need to detach cigarette converting plug and attach the cable to appropriate power supply source in the vehicle X Caution User must take responsibility for any device defect or malfunction from connecting power cable with wro
13. ng polarity For appropriate power cable installation please consult with an experience automobile mechanics or professionals as the power supply can vary from vehicle to vehicle 12 the device Connecting 1 How to insert removing SD memory card Device must be turned off before inserting or removing SD card from the device W hen inserting SD card Push the SD memory card into SD memory slot on the side of the device until a click is heard or felt through hand W hen removing SD card Push the SD memory card further into SD memory slot SD memory card will automatically be pushed out enough for user to hold and pull the card out from the slot completely X Caution Do not apply too much force when pushing the card into slot or inserting the card User will take responsibility for device malfunction or defect due to user mishandling 2 Connecting or removing USB cable User must connect USB cable into the device before attaching the device to PC W hen attempting to detach the USB cable user has to detach the USB cable from PC first before removing the cable from the device 3 Connecting AV out cable The AV out socket is located at the side of the device The cable is known as 4pole 3 5 Stereo to 3RCA cable Yellow plug is for video red for audio and white for external emergency recording button User can use AV cable when external trigger is needed Xx Caution Use only standard AV cable as specified in the above
14. ntrol button optional 3 Continuous record mode Continuous record mode will be activated with orange LED flashing when pressing MOVIE button continuously until beep Depending on user configuration MPEG4 quality video audio can be recorded for user configured period of time until it s completed and repeat record again Event record mode can be reverted back by pressing MODE button continuously again and deactivates the continuous record mode Xx Caution SD External memory card must be inserted before activating continuous record mode as it can only record into external memory card 4 Blackbox File viewing playing Mode Connect AV cable into device s AV O UT and external video audio device at its appropriate AV socket Please use only standard AV cable as defined in this manual Blackbox events will be played through its builtin video audio player by pressing p player button on the blackbox with small button beep along with red and green LED flashing back and forth continuously Prior or next blackbox file can be played by pressing lt lt or gt gt button during file viewing playing mode Event recode mode can be reverted back by pressing BR button continuously until beep and deactivate file viewing playing mode 5 MPEG4 file player M PEG 4 file codec is not included Please check our website http www true i com for more information 6 USB memory mode Device can
15. nvironment Configure audio record of the device Turns on and off sound Set the time zone of your country Load blackbox configuration file Save blackbox configuration file x Caution The configuration file name must be setup hms and saved to root directory of a SD memory card Otherwise configuration changes cannot be reflected in your blackbox End configuration window 19 Camera Image Sensor CMOS VGA Field of View F D 160 5 H 121 V 88 F 1 8 Voice Mic 192 kbps Mono G Sensor Sensor 3 Axis up to 8G Sampling period 100 Hz Event Record Resolution VGA 640 x480 fixed 15 fps Recording time M ax 40sec per event User Record Resolution M PEG 4 VGA 640 X480 Max 25fps Recording time Set by User Parking Resolution VGA 640 x480 fixed 15 fps Surveillance Detection by Motion amp Impact Recording time Max 40sec per event GPS SirfStar III On Board Intemal NAND Hash Memory 1GB External Memory Card Support SD SDHC USB Interface USB 2 0 Speaker 0 4 W Mono On Board Backup Battery Lithium Polymer 90mAh Video Audio Output NTSC PAL Mono External Switch for Recording 2 pin connector Al amp amp true i Vehicle Blackbox HMBS 200 7 Y 2 20 ra 4 a A AHS Tel HS 7 2 TUU 14 AZ Boll oto HHSEI MSS Tol
16. on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help Disclaimer Safety Guidelines Box Contents Device Features Technical Details Device installation Connecting accessories to the device User manual Firmware Upgrading Procedures true i PC Viewer Specification 10 13 14 16 17 20 Please read the following TERMS OF USE before you use the device TERMS OF USE 1 Device operation Hanman Technology is not liable for any compensation or legal responsibility of unexpected device malfunction or loss of important data at any instance Please read through whole user manual including safety guidelines and operation HMBS 200 blackbox is designed to record video before and after events at normal operation condition however the blackbox does not guarantee video record for all events at any conditions 2 Product abuse Hanman Technology is not liable for any compensation or legal responsibility of individual privacy copyright infringement that arise through user abuse by taking inappropriate video or audio In addition Hanman Technology is not liable for any compensation or legal responsibility of product damage or personal injury that arise through use of the device in an environment not defined by the product use guidelines and spec 3 For safe driving Please park your vehicle at a safe place before operate the
17. truc Vehicle Blackbox HMBS 200 USER MANUAL Caution Any changes or modifications in construction of this device which are not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment This device complies with part 15 of the FCC Rules O peration is subject to the following two conditions 1 This device may not cause harmful interference and 2 This device must accept any interference received including interference that may cause undesired operation NOTE This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions any cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet

Here

Contents

Download Pdf Manuals

Related Search

Related Contents