ULiB 200 - Pellenc
Contents
1. CB5022 Charger 2 2 100 DESCRIPTION 56 11 031A 1 Battery 9 On Off switch 2 Belt 10 Battery charge level indicator 3 Adjustment buckles 12 Charger 6 Tool power connector 13 Charging light Charging connector 14 Charger mains power plug 8 Charging connector cap 15 Charging connector 14 USING FOR THE FIRST TIME Before using the battery for the first time it must be fully charged 99 steady Refer to the battery charging chapter on page 16 1 Remove the battery and belt from their packaging 2 Position battery casing 1 on the belt so that connector 6 is on the left hand side or right hand side of the pack depending on whether you are left handed or right handed 3 Check that the On Off switch 9 is in the off position O red part not visible 4 Connect the tool power lead to the battery connector ADJUSTING THE JACKET 1 Put the jacket on 2 Using the buckles 3 adjust the length of the belt so that it rests on your hips 3 By pulling the straps 4 downwards adjust the height of the shoulder straps so that the etaining straps 5 are half taut 4 Adjust the pectoral adjustment buckle 11 to hold the shoulder straps in position WARNING To protect your back take the time to adjust the jacket correctly 56 10 014A USE 1 To save the battery power and to ensure maximum endurance of the pruning shears we advise you to2. D a EN es a ai 90096409 Translation of the original user guide USER GUIDE Pellenc power tool battery 200 READ THE USER GUIDE CAREFULLY BEFORE USING THE TOOL 56 77851 G 03 2014 Table of contents INTRODUCTION xo Caec A I CO e adde Pace Med dead pe pe Und esa c o erae 3 IMPORTANT SAFETY INSTRUCTIONS E Ca mae n a d Dr ad X Reo Ree d P deris 9 GENERAL SAPETY INSTRUCTIONS FOR THE TOOL breit b bte Liberae cedat bed 10 SAFELY MEASURES ASSOCIATED WITH THE USE OF THE CHARGER 11 SAFETY MEASURES ASSOCIATED M TH BATTERY USE nta eo EQ EIN AS ACA 12 SAFELY MEASURES FOR USING EIE TOOL 12 BATTERY SAFETY INDICATIONS x 13 DESCRIPTION AND TECHNICAL CHARACTERISTICS ee nnn 13 BATTERY TECHNICAL CHARACTERISTICS ect ur 13 CHARGER TECHNICAL CHARACTERISTICS bp bero Dd as M GU s 14 CHARGING CHARGE ba USES EU 14 DESCRIPTION ES uada RR LL I DIM AMI E E MU IL a ete he ee ad 14 USING FOR THE FIRST TIME x RO REFER QE EE EEG beso tweed d edic di cte ane Res 15 ADJUSTING THE JACKET 42 13 mcis ox ue d bei E Pa RO RH E e lap ood 15 USE ie ibi pere rura vd E dde vue
3. sJnou s noy ugaz UG OLE UE O sKep Aep 129 NONAS CLIN NONAS NOIAILIND Aep s ep Aep Aep s ep Aep DBuiunud EE sieays Buiunud di NOIT33H L Buiunud NT sJeous Buiunud uonnio 3 NOIXI n ATOd 00 007 oo NOLLONNSILINW 5 eBpeu NOIT3H SEP lt SJno O L 5410 O 9 O 0 dn YSZ dn o1 dn 810d NONAS LO LC RECOMMENDED USE OF BATTERIES AND TOOLS ACCORDING TO THEIR POWER AND AUTONOMY 21319345 Battery autonomy depends on tool the use and the vegetation being worked Autonomy calculated based the Eco mode Recommended use INTRODUCTION OUR high output MOTORS As well as Lithium Ion technology PELLENC masters the use of another revolutionary PELLENC electronic commutation motors With these revolutionary motors PELLENC has effectively rendered the heat engine obsolete PELLENC intends to impose its idea of the tool for tomorrow powerful light and pollution free tools Furthermore the PELLENC technology motor is the only electric motor with as much power
4. iU eeu Wed iode d Gabe Pure qiii a 15 CHARGING THE BAITERY i diu Rug aod Cw hac bee c ic 16 CHARGELEVELINDICATOR 4 2 ioa P Rea cado CERE Ea 18 REPLACING THE BATTERY 5551383 amp O eb coe beds obese teed deser ed eR 18 OUTSIDE THE WORK PERIOD rri doe e Sob Er oct OR hn 18 INCIDENTS porre 19 SUMMARY OF CHARGE INDICATOR AND MESSAGES Se dhe en Pen P ee Pe aA UV 19 PELLENC SA TERMS OF WARRANTY AND NON RESPONSIBILITY CLAUSE 20 SPECIAL WARRANTY CONDITIONS ERR Che CK A do E EROR E URGE Os 21 EC DECLARATION OF CONFORMITY 593 thei RR RR RR Ra nn Rol Ros 21 INTRODUCTION Dear Customer Thank you for purchasing the Pellenc power tool battery When correctly used and maintained this tool will give you years of satisfaction With more than 20 years of experience in portable electric equipment Pellenc proposes a large range of Lithium lon and Lithium Polymer powered tools intended for professional use and designed for maintenance work in green spaces orchards and vineyards and cleaning equipment for public roads Pellenc sets the stage for a new generation of tools combining the advantages of cordless electricity with the power of Lithium lon and Lithium Polymer designed for intensive high quality work Increasingly quiet and compact environmentally friendly economically very
5. 5 C 23 F and 35 C 2 95 F Lithium ion battery At the end of its life the battery must be returned to the authorized distributor from whom it was purchased to be recycled in accordance with waste regulations Pruner and battery comply with CE standards 3 3eoe A utiliser uniquement The charger supplied with the tool is exclusively designed to recharge the lithium ion avec le chargeur de batte batterie PELLENC b mod le CB5022 CB5012 REFERENCE A 200 battery UR X ce A utiliser uniquement avec le chargeur de batterie PELLENC mod le CB5022 CB5012 Usar s lo con el cargador de bater a PELLENC del modelo CB5022 CB5012 For use only with PELLENC s battery charger model CB5022 CB5012 Nur zur Verwendung mit dem Ladegerat Modell PELLENC CB5022 CB5012 0 usar com o carregador de bateria PELLENC CB5022 CB5012 modelo Per l utilizzo solo con il caricabatteria modello PELLENC CB5022 CB5012 7 DESCRIPTION AND TECHNICAL CHARACTERISTICS BATTERY TECHNICAL CHARACTERISTICS Nominal battery voltage Battery power 190 Wh Depending on the tool Weight of the battery unit 1 8 kg 3 97 16 13 CHARGER TECHNICAL CHARACTERISTICS Commercial reference of the charger 62398 60026 100 240 50 60Hz 75W 100 240V 50 60Hz 140W Voltage class Il class Charging voltage 50 2 V dc Charging current 1 2A dc max 2 2A dc max CHARGING TIME FULL CHARGE Battery CB5012 charger 1 2 A
6. Keep the power cord away from heat lubricant sharp edges or moving parts 4 f the input and or output cords are cut or damaged bring the entire device back to the authorised distributor where it was purchased 5 Do not introduce any metal objects into the device such as paper clips coins keys nails screws or other small metal objects likely to short circuit its components 6 Do not immerse the device in water PERSONAL SAFETY 1 Remain vigilant watch what you are doing and use common sense when using the device Do not use the device if you are tired or under the influence of drugs alcohol or medication MAINTENANCE AND UPKEEP 1 Have the device serviced by an approved PELLENC dealer using only identical spare parts 10 SAFETY INSTRUCTIONS SAFETY MEASURES ASSOCIATED WITH THE USE OF THE CHARGER 1 When in operation the charger s temperature can reach 60 140 F No flammable material must be within 1 5 metres 4 92 ft of the charger and battery 2 Place the charger out of children s reach and onto a non combustible support 3 Do not interfere with its cooling cycle 4 The charger supplied with the battery is designed to recharge the battery Do not charge non rechargeable batteries 5 The charging location must be equipped with a class D fire extinguisher for metal fire in good working order 6 If the output cord is cut or damaged bring the entire charger back to the authorised distributor
7. Manganese Lithium ion contains 125 Wh kg while Pellenc Lithium ion contains 250 Wh kg Moreover our ultra high capacity batteries have an exceptional service life which varies between 800 and 1 500 cycles where one cycle corresponds to a full charge and discharge Even after hundreds of days of use the battery still reaches over 80 of its initial capacity Equipped with a patented intelligent system Pellenc batteries can be charged at any time without memory effect and without altering their lithium ion components They automatically discharge after several days of non use in order to be stored risk free for several months The ultra high capacity of Ultra Lithium Batteries guarantees a pollution free odourless and quiet operation with a record level of autonomy INTRODUCTION For example a PELLENC ULB 1100 battery is equivalent to over 4700 liters of gasoline and 90 liters of mixture 56 07 011A Characteristics of the ULTRA LITHIUM BATTERY Secure system patented guarantees the preservation of your battery in the event of overloading discharging or over heating Life system patented ensures an optimum service life for your battery by protecting each of the components individually Balance system patented guarantees the balancing of the various battery components in order to optimise balanced operation Power system patented enables use of the entire range of PELLENC tools within the scope of a professional a
8. keep the blades closed and to open them only to the size of the wood to be cut 2 he battery is discharged when charge level indicator 10 shows 0 15 CHARGING THE BATTERY When the battery is discharged the tool stops automatically the charge level indicator 10 indicates 0 and the buzzer beeps intermittently see MESSAGE TABLE on page 19 A Set the On Off switch 9 immediately to the off position Before using battery for first time at the start of a new season it must be fully charged 99 steady B Place the charger and the battery in a dry ventilated area at a temperature of between 10 C 50 F and 25 C 77 F and protected from dust Lay the battery in the horizontal position CAUTION Before plugging the charger into the mains make sure that the mains supply corresponds to the rating indicated on the charger see Characteristics p 13 C Connect the mains plug 14 of the charger to the electrical mains The charger s green light comes on D Connect the charging lead 15 to the battery charging connector 7 56 10 003C 16 CHARGING THE BATTERY E When the charge level indicator 10 flashes the battery is charging Charging is complete when the charge level indicator 10 reads 33 steady 56 10 004B F Once the battery is charged disconnect the charging lead on the battery first 15 then the charger power connector 14 NOTE After
9. manual may be reproduced without the written consent of PELLENC The technical characteristics and the illustrations given in this manual are for information purposes and are in no way contractual PELLENC reserves the right to make any modification or improvement to its products as deemed necessary without informing customers already in possession of a similar model This manual forms an integral part of the tool and must accompany the tool if it changes hands KEEP THESE INSTRUCTIONS GENERAL SAFETY INSTRUCTIONS FOR THE TOOL Retain all the safety measures and instructions for later reading CAUTION Read the safety measures and all the instructions This device is not intended for use by anyone including children with reduced physical sensory or mental capabilities nor by anyone lacking in experience or knowledge except if they are supervised or have received prior instructions from a person responsible for their safety WORK AREA SAFETY 1 Keep the work area clean and well lit 2 Do not use electric tools in an explosive atmosphere for example in the presence of flammable liquids gases or dust 3 Keep children and persons present away when using the tool ELECTRICAL SAFETY 1 Never modify the connector or any other part of the device in any way whatsoever 2 Do not expose the device to rain or damp conditions 3 Do not misuse the power cord Never use the power cord to carry pull or disconnect the device
10. of an accident and total or partial destruction of the product PELLENC sa s warranty can only be granted and their responsibility engaged if the party claiming the warranty can provide technical proof specifying the origin of the accident a defect in materials or a structural defect and the product components which are the cause of it This contractual warranty excludes any other responsibility of PELLENC sa whether implicit or explicit For this reason the responsibility of PELLENC sa can not exceed the limits defined above and covers to a limited extent repair or replacement as chosen by PELLENC sa of parts recognized to be defective and when applicable the labour required to perform the repair or replacement on the basis of warranty time as defined by PELLENC sa Any maintenance or repair work whatsoever carried out during the warranty period shall mandatorily be performed by PELLENC sa or by a PELLENC sa authorized dealer under penalty of forfeiture of the warranty All costs arising from the immobilization movement approach and transport shall be in all events for the sole account of the purchaser As concerns parts or equipment that are not manufactured by PELLENC sa in particular ball screw battery etc the warranty is limited to that of the suppliers to PELLENC sa Normal wear parts worn out as the result of use are never under warranty PELLENC sa and the authorized dealer shall not be liable in the following cases
11. output with the added advantage of being small giving it an ideal weight The output of this motor is significantly higher than that of traditional direct current motors with brushes Friction caused by the brushes disappears the output of PELLENC motors is nearly 90 PELLENC motors are Brushless motors This means that their service life is theoretically infinite with only the service life of the ball bearings limiting the motor s service life There is no need for motor maintenance as opposed to heat engines PELLENC Brushless motors stop completely each time the trigger is pressed on the contrary to heat engines Therefore sound emissions are very low to the benefit of the user and his immediate surroundings Finally PELLENC Brushless motors often drive the cutting element directly no clutch or reduction gearbox meaning less noise and wear Motor control is electronic as is the power supply meaning that noises linked to mechanical part movements are extremely limited mM A f in la iA N X f 53 10 071A By using PELLENC battery and motor technology you benefit from several advantages energy savings ease and comfort of use free from motor maintenance power equivalent to and often higher than combustion engines extremely profitable tools lightweight no noise pollution or odors virtually inexistent carbon emissions Immediate start up no need for a starter PELLENC OFFERS TECHNOLOGY W
12. temperature too high gt Im 88 and beep every 2 minutes for 24 Voltage too low after hours of non use Recharge battery hours immediately CHARGING Pb and bf alternating and continuous Battery problem beep Pb and alternating Charger problem 2 Check the battery charge level on the indicator 3 Check that the lead is connected correctly and that the thumbwheel is tightened 4 Set the switch 9 to the on position l Press the operating trigger and the safety trigger depending on the tool 5 f the tool still does not operate return the assembly in its original packaging to an authorized repair station NEVER ATTEMPT TO OPEN EITHER OF THE BATTERY PACK OR CHARGER COMPONENTS you may damage them and in particular you will loose the benefit of the warranty 19 SA TERMS OF WARRANTY AND NON RESPONSIBILITY CLAUSE MACHINE RANGE FOR OEP In the event of failure of a mechanical part and subject to normal rational use and maintenance in compliance with the maintenance manual PELLENC sa guarantees its products for a period of ONE YEAR as of delivery this time shall not exceed a period of 18 months following departure from the factory of the equipment under warranty on one hand in accordance with the conditions stipulated in the warranties of PELLENC sa and on the other hand subject to the delivery report indicating the commissioning date was made known to PELLENC sa In the event
13. where the tool was purchased 7 Only recharge using the charger indicated by the manufacturer A charger adapted to one type of battery unit may present a fire risk if used with a different battery unit 8 This charger is designed to charge the batteries of Pellenc s lithium tools 9 Do not use it for any other purposes 10 Children must be supervised to ensure they do not play with the charger 11 Verify that the cable cannot be folded and does not touch hot surfaces or sharp edges 12 Ensure good ventilation during the charge 13 Never cover the charger 14 This charger must not be used outdoors 15 Make sure the power connector is not exposed to water 16 Never charge a damaged battery 17 Grid connection must comply with national electrical regulations EN60204 1 18 Check the cable of the charger before using it Never use the charger if the cable is damaged 19 When the battery is charging place the charger a non flammable support more than 1 5 m 4 92 ft away from any flammable object 11 SAFETY MEASURES ASSOCIATED WITH BATTERY USE 1 If not using the battery unit store it away from other metal objects such as paper clips coins keys nails screws or other such small metal items that might form a connection between the two terminals Creating a short circuit between the battery terminals can lead to burns or cause a fire 2 Keep the battery out of the reach of children and place it on a n
14. 350 mA EC DECLARATION OF CONFORMITY ONLY CONCERNS EUROPE MANUFACTURER PELLENC S A QUARTIER NOTRE DAME ROUTE DE CAVAILLON B P 47 84122 PERTUIS CEDEX FRANCE PERSON ENTITY AUTHORISED TO COMPILE PELLENC S A THE TECHNICAL DOSSIER ADDRESS QUARTIER NOTRE DAME ROUTE DE CAVAILLON B P 47 84122 PERTUIS CEDEX FRANCE WE HEREBY DECLARE THAT THE EQUIPMENT HEREINAFTER REFERRED TO AS GENERIC DENOMINATION BATTERY INTENDED BATTERY TORPOWERNSTANEHELDELEEHRIE POWERING HAND HELD ELECTRIC FUNCTION PELLENC TOOLS COMMERCIAL NAME ULTRA LITHIUM BATTERY TYPE Li lon Battery MODEL COMPLIES WITH THE PROVISIONS OF THE FOLLOWING EUROPEAN DIRECTIVE ELECTROMAGNETIC COMPATIBILITY 2004 108 CE THE FOLLOWING HARMONISED EUROPEAN STANDARD HAS BEEN USED NF EN 62133 08 2013 THE CHARGER COMPLIES WITH THE FOLLOWING STANDARDS EN 60335 1 2012 EN 60335 2 29 2004 A2 2010 EN 62233 2008 EN 55014 1 2006 A1 2009 A2 2011 EN 55014 2 1997 A1 2001 A2 2008 EN 61000 3 2 2006 A1 2009 A2 2009 EN 61000 3 3 2013 CONCLUDED AT PERTUIS DATED 03 03 2014 ROGER PELLENC CHIEF EXECUTIVE OFFICER 21
15. HICH MAKES THE HEAT ENGINE OBSOLETE INTRODUCTION OUR RANGE OF PRODUCTS PELLENC Green and City Technology develops new products every year in an aim to meet the requirements of professionals Today our range of products is growing and our engineers are doing their utmost to create tools thus pushing technology advances further Our passion is innovation with an aim to improve the working quality and conditions for professionals by supplying a complete range of powerful lightweight easy to handle and very profitable tools our blowers operate quietly with power modulation our hedge trimmers combine comfort and performance our grass cutting brush cutters are robust and multi functional our chainsaws are lightweight powerful and very easy to handle our pruning shears are the most powerful in the world our hoeing machines which are unique in the world replace cumbersome rotary hoes our olive harvesters are exceptionally efficient our vine tying machine combines efficiency and profitability our batteries have a very high autonomy our mobile solar panel offers the possibility to charge your batteries anywhere Exceptional light output of our autonomous lighting systems All of our tools have minimal CO2 emissions and meet the requirements of Local Collectivities or other associations in terms of a sustainable environment and ecology PELLENC is the only company to propose a full range of tools which ar
16. a long storage period new battery winter storage etc when you disconnect the charger the charge level indicator may display a value of less than 99 This is a normal phenomenon which can for up to 5 charge cycles with normal use between each charge 56 10 005B 17 CHARGE LEVEL INDICATOR The battery is equipped with a charge level indicator which indicates the charge remaining in the battery The charge indication is expressed as a percentage e The charge level indicator reads 99 when the battery is fully charged If the charge level indicator reads 55 after a day s work it is not necessary to recharge the battery for the next day s work e If the charge level indicator reads 00 or close to this value the battery must be recharged straight away e The charge level indicator can be compared with fuel on a motor When the tool is being used the indicator indicates the power consumption of the electric motor REPLACING THE BATTERY The battery must only be replaced by an authorized distributor OUTSIDE THE WORK PERIOD e Store the battery unit and its charging device in a place away from any heat dust or dampness and ensure that the switch 9 is on the 0 off position Never store the battery at an ambient temperature greater than 45 113 F To conserve the service life of the battery and to prevent its deterioration it is essential to store it in the charged st
17. ate and to recharge it every 10 months when it is not used Do not operate the switch during the storage period n order to ensure the battery s long service life it must be stored in a dry and temperate area between 32 F and 25 C 77 F e No flammable object must be placed within 1 5 meters 4 92 ft of the battery e The charger requires no maintenance Disconnect the charger prior to cleaning it Clean the charger casing using a wet cloth and mild detergent If the battery is not used for 4 days it discharges automatically to prepare for storage During this phase it will become warm 18 INCIDENTS SUMMARY OF CHARGE INDICATOR AND BEEP MESSAGES SUMMARY OF CHARGE INDICATOR AND MESSAGES O Z fixed Battery charge level 0 to 99 seconds gt D 2 Z flashing every 4 seconds Battery charge level 0 to 99 Charging complete 4 D 2 Iri i flashing Standby mode after 4 days of non use 40 to 99 Indicator off DEGRADED MODE MESSAGES Goes into storage after 7 days of non use or voltage too low gt Q Mm T and 55 alternating Stopping the tool battery temperature too high Long beep and 1 short beep otopping the tool intensity too high Long beep and 4 short beeps CHARGING T and 00 alternating Charge interrupted battery temperature too low and 45 alternating FAULT MESSAGES Stopping the tool tool temperature too high Charge interrupted battery
18. ctivity thanks to the restitution of the battery s maximum capacity Advantages of the ULTRA LITHIUM BATTERY Environmentally friendly the energy used by PELLENC tools is environmentally friendly and participates in an initiative towards sustainable development Compared to equivalent heat engine powered tools CO2 emissions are 30 to 90 times lower Power PELLENC equipment ensures the user has an unequalled power supply of up to 3 000 W Savings the battery permits up to a full day of work at a derisory total cost Ergonomics PELLENC tools are very quiet and light offering unrivalled comfort and optimal working conditions Cost effectiveness the cost of your battery will be recovered in under a year of use from 135 days The return on investment in the battery over its service life is greater than 5 000 thanks to the savings on fuel which is not required Compatibility of our batteries with our machines All PELLENC multi function Ultra Lithium Batteries can be used on all of our machines However we recommend the use of batteries according to the tool in order to achieve an increased optimization of autonomy power and weight You use 5L of mixture per day at a price of 1 50 per litre Data calculated for the regular use of the ULIB 1100 battery INTRODUCTION J9M0J Q 9 YSNIG 0006 usnuq Bunjno sseJB 0021 NOI T39X3 s noy zo sinoug oe sinou ge 0
19. e 100 clean and with zero CO2 emissions thanks to the SOLERION solar panels which can be used to recharge our batteries 56_10_037B INTRODUCTION Battery converter Power Convertor 1000 W Hedge trimmer HELION Universal Vineyard pruning shears LIXION Evolution Vineyard pruning shears LIXION Evolution Il Chainsaw SELION C20 ui Nieren ULIB Battery Orchard and green space pruning 200 400 700 1100 M POLY 5 OLIVION 2 hands TREELION D45 Orchard and green space pruning shears Blower TREELION M45 AIRION Brush Cutter EXCELION 2000 Grass Cutting Brush Cutter EXCELION 1200 Hoeing machine CULTIVION Chainsaw on pole SELION Pole or Telescopic v Hedge trimmer on pole HELION Pole or Telescopic Olive harvester OLIVION Pole or Telescopic INTRODUCTION ENVIRONMENTAL PROTECTION Your equipment comprises numerous materials which can be valorised or recycled Entrust these to your reseller or to an approved service centre so that they can be processed Comply with the regulations in force in your country as concerns environmental protection mEEN associated with your activity IMPORTANT SAFETY INSTRUCTIONS KEEP THESE INSTRUCTIONS This manual contains important information and operating instructions for the ULIB 200 battery model Before using the battery read all instructions and warnings featured o
20. e Malfunctions due to faulty servicing user inexperience or abnormal use Failure to perform overhauls and checks in accordance with manufacturer s instructions Replacement of genuine parts or accessories with parts of accessories of another origin or when the machine sold has been transformed or modified This warranty is explicitly limited to the terms defined above PELLENC sa shall not be liable under any circumstances for payment of any indemnity for any reason whatsoever However it is specified in compliance with the provisions of decree No 78 464 dated March 24th 1978 that this contractual guarantee does not replace the legal guarantee which obliges the seller to guarantee the buyer against the consequences of defects or hidden defects of the object sold 20 SPECIAL WARRANTY CONDITIONS PELLENC s a guarantees its motor for a period of THREE YEARS from the date of delivery PELLENC s a guarantees the battery for a period of THREE YEARS from the date of delivery on the condition that the number of recharging operations does not exceed 100 per year the battery charging capacity has not exceeded 1 000 000 mAh since it was put into service the battery is used at a temperature of between 5 C and 35 C 23 F and 95 F the battery is charged at a temperature of between 10 C and 25 50 F and 77 F the battery has not been heavily discharged the average consumption does not exceed
21. n the battery charger the battery and the product using the battery Always comply with the instructions and illustrations in the manual The Pellenc power tool battery is a professional tool reserved exclusively for compatible Pellenc tools e PELLENC declines all responsibility in case of damage caused by improper use and use other than for which it is intended e PELLENC also declines all responsibility in case of damage caused by the use of non genuine parts or accessories All through this user guide you will find advisory notes and information entitled REMARK CAUTION WARNING A REMARK provides additional information clarifies a point or explains a step to be followed in detail The CAUTION and WARNING advisories are used to define a procedure which if neglected or incorrectly performed may lead to serious damage to the equipment and or personal injury This advisory indicates that if the procedures or instructions are not complied with any damage will not be covered by the warranty and the owner will be responsible for the repair costs Safety indications are also given on the tool they remind you of the safety precautions to be taken Identify and read these indications before using the tool Immediately replace any indications that may become partially illegible or deteriorated Refer to the SAFETY INDICATIONS heading in order to identify the location of the safety indications on the tool No part of this
22. on combustible support 3 Do not interfere with its cooling cycle 4 Do not use or leave the battery near a heat source gt 60 C or 140 F 5 Do not leave the battery in direct strong sunlight 6 Do not expose the battery to microwaves or high pressure 7 Do not immerse the battery in water 8 The batteries must be charged in a dry ventilated room at a temperature between 10 50 F and 25 77 F maximum away from any moisture 9 f the battery is not used for 4 days it discharges automatically to prepare for storage During this phase it will become warm 10 Over time the capacity of your battery reduces When it reaches half of its original autonomous operating time it should be replaced 11 The battery may lose 1 to 4 of its capacity when exposed to a temperature higher than or equal to 55 131 F for one week 12 The charging location must be equipped with a class D fire extinguisher for metal fire in good working order 13 If the whole tool or the battery is to be shipped somewhere comply with the applicable standards The battery is a classified product UN3091 class 9 packaging group 2 14 Use of a battery other than that provided by Pellenc SA is dangerous risk of serious injury If a different battery is used Pellenc SA cannot be held responsible for any consequences 15 The battery must be protected from any impact and must be positioned and secured appropriately during
23. profitable and complying with ever more strict specifications regarding ergonomics power and autonomy Pellenc tools prove their worth every day whether in vineyards orchards or for the maintenance of green spaces and public sectors Pellenc tools are the world leader in this field Because of the lightweight nature and easy handling of PELLENC tools users can work better with less effort without noise and faster than with heat engine powered tools A single unique energy source powers PELLENC tools intended for professional use The Ultra Lithium Battery This revolutionary battery is available in several models with extended work capabilities Once purchased this battery is compatible with most of the Pellenc Green and City Technology range of products Innovation ability to listen quality and environmental friendliness are PELLENC priorities OUR high capacity Ultra Lithium ion BATTERIES PELLENC is the first and only manufacturer worldwide to propose a whole range of professional tools for Parks and Gardens Local Collectivities Golf Courses Orchards Vineyards etc which operate on ultra high capacity ternary Lithium ion batteries PELLENC has developped its own Lithium based technology in order to achieve the best compromise between output power autonomy weight and ergonomics The result is enlightening as the Pellenc Lithium ion technology is nearly two times more efficient than the Manganese Lithium ion technology
24. transportation 16 In the case of suspicious smoke place the battery outside the charging area or transportation vehicle as far away as possible from any inflammable material 17 Never store a battery when its capacity is below 45 Recharge it before storage if the value is below 45 96 18 Under inappropriate conditions liquid may leak from the batteries avoid any contact In the event of accidental contact rinse with water In the event of contact with eyes seek professional medical help The liquid leaking from the batteries can cause irritations or burns 19 Pellenc power tools must only be used with the battery units designed for the purpose Use of other battery units can present a risk of injury and fire 20 Only recharge using the charger indicated by the manufacturer A charger adapted to one type of battery unit may present a fire risk if used with a different battery unit 21 Do not use the battery for any purpose other than that initially envisaged exclusively for use with Pellenc tools 22 At the end of its life the battery must be returned to the authorized distributor from whom it was purchased to be recycled in accordance with waste regulations 23 Fragile case contains an electronic board and lithium SAFETY MEASURES FOR USING THE TOOL Refer to tool s manual 12 BATTERY SAFETY INDICATIONS Do not expose to rain Read the user manual This equipment must be used at a temperature of between
Download Pdf Manuals
Related Search