OBDⅡ User Manual
Contents
1. left of LCD is turned on stop treadling the accelerator and check RPM At this time Green lamp of sensor is turned on KS RnD CO LTD 7 Preparation for measuring engine speed is completed Please tread the accelerator to make level you expected and then measure RPM 2 OBD I Communication 2 1 Preparation before use 1 Hold the hand breake and put the bridging in front and in back of the tire 2 Set the car s gear in neutral and start an engine 2 2 How to Connect Devices 1 Attach the OBD II module in car 2 Connect the DC12V adapter to nv of device 3 When an initial check is completed CHK on the left of LCD is turned on and rdy is marked on LCD display KS RPM User Manual 2 3 Engine speed measurement 1 When the device automatically recognize OBDH communication and properly connected GOOD lamp flashs and current RPM value is marked X Detach the OBD2 module unless you can t measure by phono magnetic methood Oil Temperature measurement Option sis 1 Connect the sensor to ID of the machine 2 TEMP lamp of the right of LCD is turned on and display a current temperature 3 Input your sensor to place that measure the car s engine oil X Watch out burn since engine oil is hot Error of oil temp Display Explanation Temperature is higher than the measurement range over 200 0 C OW Temperature is lower than the measurement range below 200 0 C2. KS RP Mo User Manual KS RnD CO LTD KS RPM OBD I User Manual V0 4 Table of contents User Precaution 3 COMPONEN 22 2 4 QPOs TEN 4 Technical Specifications 5 Material 5 Product Name 6 1 Phono Magnetic Sensor 6 1 1 Preparation before Use 6 1 2 How to Connect Devices 6 1 3 Measurement flow chart 00000000000 7 1 4 Measurement engine speed 8 2 OBDI Communication measurement 9 2 1 Preparation before Users dieses ei eee wees 9 2 2 How to Connect Devices 9 2 3 Measurement engine speed ssssss 10 Measurement Oil Temperature 10 Example of Attaching Sensor 11 KS RnD CO LTD User Precautions Please use this product after you have read the manual carefully to use the device more safely and efficiently lt General Safety Compliance gt 1 Don t use this product except for those who know how to use 2 Do execute text of manual before measurement 3 Do not disassemble the device lt Dangerous gt 1 This product s 12V adapter is dedicated to AC220V Please check the power before use 2 Avoid content with rotor near the engine during measuring engine speed 3 When you measure engine speed be cautious for burn 4 For your safety hold the hand brake
3. Oil sensor has a problem 10 KS RnD CO LTD Example of attaching sensor 11 KS RnD CO LTD Techno park 201 906 1 388 Songnae daero Wonmi gu Bucheon si Gyeonggi do 420 733 Korea Tel 82 32 325 6920 Fax 82 32 325 6921 www ksrnd com
4. and put the bridging in front and in back of the tire KS RPM User Manual KS RPM oBDI Composition Item KS RPM machine body Bluetooth ELM327 Sensor of measuring RPM 5 m X Bluetooth ELM327 example A KS RPM OBD I Option KS RnD CO LTD KS RPM OBDI Technical Specifications maspane Resolving Sensor 1 rom Power 1 rom Power Oil Temperature r Resolving _ 0 1 Power Use Humidity Range 30 90 Communication RS292 KS RPM OBD I Material Sensor Cable soft PVC KS RPM User Manual Product Name RPM status display RPM Temp display Bluetooth antenna Sensor input RPM display RS232 communication Power DC12V 1 Phono Magnetic Sensor 1 1 Preparation before use 1 Hold the hand breake and put the bridging in front and in back of the tire 2 Set the car s gear in neutral and start an engine 3 Open the bonnet of a car 1 2 How to Connect Devices vis 1 Connect the measurement sensor 15 pin connector to AID of device and place where there is no vibration 2 Connect the DC 12V adapter to nv of device KS RnD CO LTD 1 3 Measurement flow chart _ Initial Check CHK GOOD CHK GO0OD _ altemately on Initial check state lamp does not light flicker CHK lamp Initial check state display Err gt put sensor signal a Finish initial Without vibration check state sensors located CHK lamp ligh
5. ts _ Display ray Attach sensor on engine Disconnected sensor Checking idle No change during 10 sec Within 10 sec A normal RPM value Standby checking accelerator Step on the accelerator 3000rpm normal RPM value Finish measure set up KS RPM User Manual 1 4 Engine speed measurement 1 When the power is turned on version is displayed Execute an initial check alternately twinkling CHK and GOOD on the left of LCD 2 When an initial check is completed CHK of the left of LCD is turned on and rdy is marked on LCD display At this time red lamp of sensor is turned on 3 Attach magnet of sensor on flat surface around the engine X Sensor do not touch the rotor around the engine X Attach sensor on flat surface avoiding the edge of the engine refer to page 11 4 After a few seconds CHK and GOOD on the left of LCD are turned on at the same time And then current engine speed is marked on display At this time Yellow lamp of sensor is turned on X Ifthe difference between measurement and RPM gauge value is lage disconnect the sesor and connect the sensor again when rdy is maked or LCD display X IF rdy is maked more than 10 seconds disconnect and connect again the sensor 5 When normal engine speed is displayed maintain 2000 2500 of the engine speed for a few seconds by treadling the accelerator 6 When only GOOD on the
Download Pdf Manuals
Related Search