IDM Bluetooth Hand-held Scanners
Contents
1. Once you scan one of the above commands the link indicator of the scanner will give 3 blue blinks per 2 seconds during the searching process You have to execute the Bluetooth Discovery procedure to find available Bluetooth devices Select IDMxxx If you use HID Mode please go to step 5 If you use HID Mode with Passkey you will be requested to enter the passkey PIN on the remote host Please enter the passkey PIN accordingly by scanning the Option Codes page 13 and then scan FIN Finish to end the passkey entry Continue with step 5 3 If you scan HID Legacy Mode the passkey PIN may be requested Please enter 00000000 default setting You will see Keyboard on IDMxxx Double click this HID service to establish the connection between the scanner and the remote host device The scanner will emit 4 beeps in ascending tone to indicate the radio is connected At the same time the link indicator of the scanner will give 1 blue blink per 2 5 seconds to indicate the scanner is in radio connected state Please note that if the scanner is not connected to the host device within 1 minute after scanning the above command the scanner will go to sleep automatically You can just press the trigger to wake up the scanner to continue the installation amp The above procedures are based on popular Windows environment However the installation procedure may vary depending on different remote host d2. Auto sense Disable Auto sense amp 7 Sleep Mode amp Power Off The scanner is preset to enter Sleep Mode if the scanner is not used after time out duration When the scanner is under sleep mode it is preset to enter Power Off automatically if it will not be waked up after time out duration If you want your scanner to enter Sleep Mode or Power Off immediately please scan the Sleep Mode or Power Off command The scanner can be waked up by pressing the trigger button mE AMI Power Off 8 Batch Scanning Inventory Mode With the help of the Batch Scanning function the scanner is capable of storing the barcode data of up to 100 000 EAN 13 barcodes This functionality is often used for inventory applications Once you scan the Enter Batch Scanning command to activate this function all scanned barcode data will be stored into the memory storage and the status indicator of scanner will give green blink at regular interval during batch scanning You can scan and store the barcode data till the memory storage is full If the storage is full you will hear 2 long beeps and the status indicator will give 2 red blinks to indicate out of storage To terminate the batch scanning please scan the Exit Batch Scanning command Enter Batch Scanning II Exit Batch Scanning How to Transmit Stored Data The scanner is preset to transmit a
3. 2 5 seconds and the power indicator of the smart cradle turns steady blue If the scanner and smart cradle just give alternative red and green blinks Uninstall state please follow step 5 to establish the connection between scanner and smart cradle Scan the PAIR mode command The status indicator of the scanner will turn steady red immediately s ll PAIR Mode Place the scanner into the smart cradle You will hear one short beep to indicate the activation of the pairing process The scanner will emit continuous short clicks and the link indicator of the scanner will flash blue quickly during the pairing process When you hear 4 beeps in ascending tone the pairing process is completed You will see that the link indicator of the scanner gives 1 blue blink per 2 5 seconds and the power indicator of the smart cradle turns steady blue If the scanner pairing process failed or if the scanner is not placed into the smart cradle within 20 seconds you will hear 2 Di do Di do beeps to warn the failure of pairing The scanner will return to the uninstall state automatically Q Scan the corresponding host interface quick set command to complete the installation IS The default host interface of smart cradle is USB HID If you want to set the interface to USB COM you have to install the USB virtual COM software driver available on www sick com into your host device before using the scanner All host interf
4. 472 3733 South Korea Phone 82 2 786 6321 4 Suomi Phone 358 9 25 15 800 Sverige Phone 46 10 110 10 00 Taiwan Phone 886 2 2375 6288 Turkiye Phone 90 216 528 50 00 United Arab Emirates Phone 971 0 4 8865 878 Italia USA M xico Phone 39 02 27 43 41 Phone 1 952 941 6780 Japan 1 800 325 7425 tollfree Phone 81 0 3 5309 2112 Magyarorsz g Phone 36 1 371 2680 Nederland Phone 31 0 30 229 25 44 Detailed addresses and additional Norge representatives and agencies Phone 47 67 81 50 00 at www sick com SICK SICK AG Waldkirch Germany www sick com Sensor Intelligence
5. QUICK START IDM Bluetooth Hand held Scanners SICK Sensor Intelligence 1 How to use this guide This document provides a quick reference for installation and operation of IDM Bluetooth scanners A complete user guide can be found on www sick com The document contains a collection of codes that allow you to configure the IDM Factory default values are marked with a symbol To configure the device scan one or in some cases a sequence of codes In some cases you also need to scan option codes contained in the back of this quick start guide Eine deutsche Version der Kurzanleitung steht auf www sick com zur Verf gung for german version of quick start check www sick com 2 Getting familiar with your IDM BT scanner IDM Bluetooth Scanner IDM1441 Series IDM2441 Series Link Indicator Status Indicator Beeper Scan Window Trigger Battery Cavity End Cap Tether Plate Lanyard catch Retaining screw 800000060000 IDMx4x Charging Cradle Power Indicator Host interface port Status Indicators DC Power Jack Paging reset button Reserved USB Bus Power Switch 3 Preparations before Using Battery installation AP Aa Ensure the battery contacts of the battery pack are facing the charging contacts inside the battery cavity Slide the battery pack into the battery cavity until hearing a click sound before locking it with the end cap The scanner will give 4 beeps when the battery pack is installed properly
6. ace quick set codes can be found on page 12 of this guide 4 4 2 Using IDM BT in PICO Mode Ensure the battery is fully charged Choose the interface cable plug it into the smart cradle and connect it to the host device USB PS 2 RS 232 Turn on the power of your host device Ensure the status indicators of the smart cradle give alternative red and green blinks Uninstall state If the smart cradle is paired with other scanners press and hold the paging rest button for more than 5 seconds to un pair all paired scanners This way the smart cradle will return to uninstall state automatically Prepare the scanners you would like to pair with the smart cradle Ensure that the status indicator of each scanner gives alternative red and green blinks Uninstall state If the scanner is no in the Uninstall state scan the Uninstall command to un pair the scanner then scan the PICO Mode command The status indicator of the scanner will turn steady red PICO Mode Place the scanner into the smart cradle You will hear one short beep to indicate the activation of the pairing process The scanner will emit continuous short clicks and the link indicator of the scanner will flash blue quickly during the pairing process When you hear 4 beeps in ascending tone the pairing process is completed You will see that the link indicator of the scanner gives 1 blue blink per 2 5 seconds The power indicator of t
7. default the DPM functionality is not disabled However please note that if you take out the battery of the scanner the DPM functionality will be disabled automatically If you disable the DPM functionality the performance of reading printed 1D and 2D codes will be improved 11 10 Link Mode Quick Set PAIR Mode SPP Master Mode HID Legacy Mode PICO Mode IM a mE ILE HID Mode with Passkey UNINSTALL 11 Host Interface Quick Set Working with Smart Cradle only USB HID Standard Mode USB HID Turbo Mode RS232 Serial PS 2 DOS V Keyboard Replacement USB Com Port Emulation PS 2 DOS V KBW Standard Mode PS 2 DOS V KBW Turbo Mode 12 Keyboard Layout Quick Set USA France Germany Latin America Nertherlands United Kingdom UK Canadian French Spain 12 13 System Commands System Information u I NM 7770 ik LUI IN Power Off Master Default Save Configuration Clone Paging helps to locate the paired smart cradle or scanner If you would like to page the paired smart cradle you can scan the Paging command If you would like to page the paired scanner you can press t
8. e Mode command and the link indicator of scanner will give 3 blue blinks per 2 seconds during searching process _ Li SPP Slave Mode Execute the Bluetooth Discovery procedure to find all available Bluetooth device list in your remote host You will see IDMxxxx is shown in the list if the scanner is successfully discovered f Double click the IDMxxx on the discovered Bluetooth devices If the PIN Code or Passkey is requested for security connection please enter 00000000 default setting You will see Serial Port on IDMxxx Please double click this SPP service to establish the connection between scanner and remote host device The scanner will emit 4 beeps in ascending tone to indicate the radio is connected At the same time the link indicator of the scanner will give 1 blue blink per 2 5 seconds to indicate the scanner is in radio connected state Please note that if the scanner is not connected to the host device within 1 minute after scanning the SPP Slave Mode command the scanner will go to sleep mode automatically You can just press the trigger to wake up the scanner to continue the installation IS The above procedures are based on popular Windows environment However the installation procedure may vary depending on different remote host devices operating systems and the Bluetooth drivers 5 Out of range Scanning When the radio connection is establ
9. emit 4 beeps in ascending tone to indicate the radio is connected At the same time the link indicator of the scanner will give 1 blue blink per 2 5 seconds to indicate the scanner is in radio connected state Please note that if the scanner failed to connect to the host device within 30 seconds the link indicator will give 3 blue blinks per 2 seconds But the scanner is still continuing to discover the host device for another 30 seconds before go to sleep In the interim you still can scan the Uninstall command to revert the scanner to uninstall state If the scanner is already in sleep mode you just need to press the trigger to wake up the scanner to continue the installation The above procedures are based on popular Windows environment However the installation procedure may vary depending on different remote host devices operating systems and the Bluetooth drivers Establish SPP Slave Connection Ensure the battery is fully charged and a virtual COM port is available in your remote host for connecting the scanner If not please open the folder Client Applications located in Bluetooth Advanced Setting Click the Add COM Port to add one more Bluetooth COM port gt Power on the scanner within radio coverage and ensure the status indicator of scanner gives alternative red and green blinks in Uninstall state If the scanner is not in uninstall state please scan the Uninstall command first Then scan the SPP Slav
10. evices operating systems and the Bluetooth drivers 4 4 Using IDM BT in SPP Mode Establish SPP Master Connection Ensure the battery is fully charged Open the folder Hardware located in Bluetooth Advanced Setting of the remote host device to check its device MAC address Then prepare a 12 character Code 128 barcode of the remote host device MAC address or follow the step 4 to input MAC address by scanning 12 option codes Ensure a virtual COM port is available in your remote host for connecting the scanner If not please open the folder Local Services located in Bluetooth Advanced Setting Click the Add Serial Services to add one more Bluetooth COM port Power on the scanner within radio coverage and ensure the status indicator of the scanner gives alternative red and green blinks Uninstall state If the scanner is not in uninstall state please scan the Uninstall command first then scan the SPP Master Mode command The status indicator of the scanner will turn steady red immediately us ll ll SPP Master Mode 79 Scan a 12 character MAC address barcode or scan 12 option codes and FIN command to confirm your inputs The scanner will emit continuous short clicks and the link indicator of the scanner will flash blue quickly during the radio connecting process If the PIN Code or Passkey is requested please enter 00000000 default setting The scanner will
11. he paging rest button ofthe smart cradle no longer than 5 seconds 14 Operation Mode Quick Set EM LLLI mM UU AUTH Presentation Mode 15 Option Codes UL III MINI INN N UL IN INN N INN IMEN j NN INNIN MT MN MIN HIN INN N 7 F LIT MIN FIN Finish END Exit 16 Indications Scanner Indications IDM Smart Cradle Indications n ag 5 Power Indicator dips P Status Indicator s m The Bink Smart Cradle Upgrade State Steady red Short clicks Uninstall state Alternative red green blinks paged IDM Charging Cradle Indication Power Indicator Steady blue 14 03 02 DD 8M sw int43 8017157 YIT8 2015 Australia Phone 61 3 9457 0600 1800 33 48 O2 tollfree Belgium Luxembourg Phone 32 0 2 466 55 66 Brasil Phone 55 11 3215 4900 Canada Phone 1 905 771 14 44 Cesk republika Phone 420 2 57 91 18 50 China Phone 86 4000 121 000 1852 2153 6300 Danmark Phone 45 45 82 64 00 Deutschland Phone 49 211 5301 301 Espana Phone 34 93 480 31 00 France Phone 33 1 64 62 35 00 Great Britain Phone 44 0 1727 831121 India Phone 91 22 4033 8333 Israel Phone 972 4 6801000 sterreich Phone 43 0 22 36 62 28 8 0 Polska Phone 48 22 837 40 50 Romania Phone 40 356 171 120 Russia Phone 7 495 775 05 30 Schweiz Phone 41 41 619 29 39 Singapore Phone 65 6744 3732 Slovenija Phone 386 0 1 47 69 990 South Africa Phone 27 11
12. he smart cradle turns steady blue and the status indicators turn steady green If the scanner pairing process failed or if the scanner is not placed into the smart cradle within 20 seconds you will hear 2 Di do Di do beeps to warn the failure of pairing The scanner will return to the uninstall state automatically Scan the corresponding host interface quick set command to complete the installation Repeat the same procedure to pair other scanners up to seven scanners in total with the smart cradle IS For your convenience the smart cradle automatically assigns ID numbers to each scanner Once you completed all pairing processes please scan the System Information code to check the assigned ID number of each scanner 4 hs Using IDM BT in HID Mode Ensure the battery is fully charged Power on the scanner within radio range and ensure the status indicator of the scanner gives alternating red and green blinks Uninstall state If the scanner is not in uninstall state please scan the Uninstall command first Uninstall If your remote host is equipped with the latest Bluetooth drivers or if it is an iOS or Android device we recommend to use HID Mode for quick pairing If necessary you may use HID Mode with Passkey to establish a more secure connection If you experience problems in HID Mode try HID Legacy Mode instead IL LLL m INN IN HID Legacy Mode HID Mode with Passkey
13. if the battery pack still has power Secure the end cap with the screw provided IDMx4x series or via turning the integrated thumb wheel IDMx6x series You can use the overlapping battery label to pull out the battery if needed Charging the Battery 99 Choose an appropriate plug and slot it into the power adapter cavity until it is locked Then plug the AC power plug into the appropriate AC wall socket Plug the DC power cord of the power supply unit into the DC power jack of the cradle The smart cradle emits the power on beeps and the power indicator gives one blue blink If you use the charging cradle the power indicator turns steady blue Place the scanner on the cradle The status indicator of scanner will turn steady red if the battery is not fully charged When the battery is fully charged the status indicator of scanner turns steady green amp Please charge the new battery pack for 8 hours prior to the first use Use USB Bus Power Olf USB 3 0 is available both battery charging and regular nn operation can be supported by the USB Bus Power without using external power supply If you want to use this feature please slide the USB bus power switch to ON Then connect the cradle and host device via USB F cable For USB 2 0 the external power supply unit is needed amp Ensure that the cable is pushed all the way into the RJ inlet of the base cradle 2 4 Radio Link Mode The IDM Bluetoo
14. ished between scanner and remote host device the scanner will transmit each scanned code content right after scanning the barcode However the scanner is preset not to scan any barcode data when it loses the radio connection with the remote host device If you enable the Out of Range scanning function the scanner can continue scanning barcode data while it is out of radio coverage All scanned data will be temporarily stored in the memory buffer until radio link resumed Enable Out of range Scanning Disable Out of range Scanning If the scanner is out of radio coverage you will hear 4 beeps in descending tone to indicate the loss of radio connection The link indicator of the scanner will give 3 blue blinks per 2 seconds Once the scanner is back to radio coverage you will hear 4 beeps in ascending tone to indicate the radio connection is rebuilt and the scanner will give 1 blue blink per 2 5 seconds At the same time all stored scanned data will be transmitted automatically right after the radio link is resumed 6 Presentation Scanning The Presentation Scanning is designed for hand free applications If the Presentation Scanning Auto sense function is enabled the scanner is capable of automatically switching to presentation mode as soon as you place the scanner onto the Presentation Stand or into Smart Cradle Presentation scanning on cradle is only available for IDMx41 series Enable
15. ll the stored data by scanning the Transmit Stored Data command During the transmission the scanner will emit continuous short clicks and the link indicator will blink blue Then the scanner will give two short beeps after data transmission is completed Transmit Stored Data You are still able to set the scanner to transmit the stored data by placing the scanner onto the cradle as well Transmit Stored Data by Placing Scanner onto Cradle Transmit Stored Data by Scanning Barcode or Placing Scanner onto Cradle If a wrong barcode was scanned the Delete Last Scanned Data command is helpful to recover mistakes By scanning the Delete Last Scanned Data command the last stored data can be deleted Delete Last Scanned Data Transmit Stored Data by Scanning Barcode Command amp For using the quantity feature and changing the output format please refer to the complete user s manual available on www mysick com 10 9 DPM functionality If you own a DPM model IDMxxx x2xx you can enable or disable the DPM code reading functionality by scanning one of the following barcode commands Enable DPM functionality 4 Disable DPM functionality In order to verify if the DPM functionality is enabled please scan the following barcode If you can read this barcode the DPM functionality is enabled amp If you scan factory
16. radle please press and hold the paging reset button of the smart cradle for more than 5 seconds If you just want to un pair part of the paired scanners please take those paired scanners and scan the Uninstall command HID Mode HID communication directly to Bluetooth host without cradle Through the HID service the scanner can work as a Bluetooth Keyboard In this mode the scanner will be discoverable by the radio connection request issued by the remote host device In some cases you may be requested to enter the Passkey PIN to establish the Bluetooth connection for security purpose SPP Master Slave Mode Serial communication directly to Bluetooth host without cradle Through the standard SPP service the scanner can work as a Bluetooth Serial Device In SPP Master Mode the scanner initiates the radio connection request to the remote slave device In SPP slave mode the scanner will be discoverable by the radio connection request issued by the remote host device 4 1 Using IDM BT in PAIR Mode Ensure the battery is fully charged You may refer to the section of Preparations before Using for details Choose the interface cable plug it into the smart cradle and connect it to the host device USB PS 2 RS 232 Turn on the power of your host device f Note that if the scanner is shipped together with a smart cradle they are pre paired already You will see the link indicator of the scanner gives 1 blue blink per
17. th scanners provide several radio link modes to communicate with the host device When the Bluetooth enabled host device is not available the scanner can work with the smart cradle in PAIR mode peer to peer connection or PICO mode multiple connections to provide a plug and play cordless migration of your existing non Bluetooth devices Moreover you are able to use the scanner to work with Bluetooth enabled host devices via SPP mode or HID mode When the radio link is disconnected the scanner is capable of reconnecting the radio link automatically when it returns to the communication coverage Please note that this feature is not available in SPP slave mode If you would like to change the radio link mode please scan the Uninstall command to reset the scanner to the uninstall state PAIR Mode 1 scanner connected to 1 cradle If the Bluetooth device is not available in your existing system PAIR mode is the simplest plug and play solution In this mode a smart cradle can only work with one scanner The smart cradle not only provides the Bluetooth radio link with the scanner but also offers the legacy cabled interfaces to the host device including USB HID USB COM PS 2 DOS V Keyboard Wedge and RS 232 serial PICO Mode up to 7 scanners connected to 1 cradle For the requirement of multiple connections up to 7 scanners can be connected to one smart cradle concurrently If you would like to un pair all scanners paired with the smart c
Download Pdf Manuals
Related Search